CATERPILLAR

More documents

Recommendations

Info

Illustration 53: SIS Configuration dialog Step 14 On the Ready to Install dialog, click the “Install” button. Illustration 54: Ready to Install dialog 74
Step 15 After the files have been copied, the Installation Complete dialog will be displayed. Click the “Finish” button to end the installation. Be sure to install the SIS data. See instruction below to install SIS data. Illustration 55: Installation Complete dialog Note: SIS is not ready to use. As of 2004B, SIS DVD will need to be licensed before it will work. Also, data profiles and users will need to either be created on the computer or imported before users will be able to fully operate the software. Please see the SIS DVD Installation and Administration.pdf for more information. This file is located in the training folder on the root drive of STW installation CD. 75
Page 1 and 2:
1 CATERPILLAR Service Technician Wo
Page 3 and 4:
Table of Contents Introduction.....
Page 5 and 6:
Installation.......................
Page 7 and 8:
Computer/Software Hardware Recommen
Page 9 and 10:
If you do not have Service Technici
Page 11 and 12:
Illustration 4: The STW setup will
Page 13 and 14:
Select the “Yes” button to cont
Page 15 and 16:
Step 8 Select Components The Select
Page 17 and 18:
Frequently Asked Questions If you a
Page 19 and 20:
Q) How do I subscribe to SIS and/or
Page 21 and 22:
Purpose If communicating Service In
Page 23 and 24: - OR - 7X-1700 - Caterpillar Commun
Page 25 and 26: Instructions To set up the Communic
Page 27 and 28: The service tool will remain unaffe
Page 29 and 30: 202 A required INI file was not loc
Page 31 and 32: Challenger Technician Purpose The C
Page 33 and 34: Dataview DataView measures and logs
Page 35 and 36: • To Delete Existing Lines from a
Page 37 and 38: MNTWOCTL (Direct Labor to Approval
Page 39 and 40: Illustration 14: Enter the intended
Page 41 and 42: Illustration 16: A question mark ca
Page 43 and 44: Illustration 19: Other shift time e
Page 45 and 46: Illustration 22: Enter the appropri
Page 47 and 48: Labor Approval Setup - DBS DBS must
Page 49 and 50: Labor Upload -End of Job Setup Illu
Page 51 and 52: Illustration 29: Open the SIMS DBS
Page 53 and 54: Illustration 32: Save the report te
Page 55 and 56: Select the Upload Settings Tab and
Page 57 and 58: Example of file name and save: AA00
Page 59 and 60: 1-877-598-8920 DCS Support Center:
Page 61 and 62: 1. Run the SIS Setup CD on the netw
Page 63 and 64: o Select the TA inspection to open.
Page 65 and 66: � � Illustration 43: TA Search
Page 67 and 68: o o Illustration 46: The TA Navigat
Page 69 and 70: o Following are items and their bac
Page 71 and 72: Step 9 On the STW installation main
Page 73: Step 12 In the Software License Agr
Page 77 and 78: Illustration 57: Program Maintenanc
Page 79 and 80: Step 17 After the files have been c
Page 81 and 82: Illustration 63: Monthly Data Updat
Page 83 and 84: Service Information System Web (SIS
Page 85 and 86: Parts Integrator Purpose Parts Inte
Page 87 and 88: - The integration software has been
Page 89 and 90: Illustration 74: Step 8 Once the
Page 91: Refer to the STW Knowledge Entry li
show all

CATERPILLAR

Create successful ePaper yourself

Delete template?

Save as template?