YVAA Style A Air-Cooled Screw Liquid Chillers ... - Johnson Controls

More documents

Recommendations

Info

SECTION 5 - TECHNICAL DATA 70 UPPER HOUSING LOWER HOUSING NON-SKID ELASTOMERIC PAD (D) ONE INCH DEFLECTION ISOLATOR INSTALLATION 1. Read the following instructions before beginning installation. 2. Isolators are shipped fully assembled and are to be positioned in accordance with the submittal drawings or as otherwise recommended. 3. Set isolators on floor, housekeeping pad or subbase, ensuring that all isolators centerlines match the equipment mounting holes. The VMC group recommends that the isolator base (“B”) be installed on a level surface. Shim or grout as required, leveling all isolator bases to the same elevation (0.25-inch maximum difference can be tolerated). 4. Bolt or anchor all isolators to supporting structure utilizing base slotted holes (“C”). POSITIONING PIN (H) 0.25” min - 0.5” max (C) (B) FORM 201.28-NM1.1 ISSUE DATE: 8/29/2012 EQUIPMENT BASE (C) 5. Place equipment on top of isolators making sure that mounting holes of the equipment line up with isolator positioning pin (“H”). 6. Equipment or machine is at its full operating weight. 7. Adjust each isolator in sequence by turning spring adjusting bolt (“D”) one full counterclockwise turn at a time. Repeat this procedure on all isolators, one at a time. 8. Continue adjusting each isolator until a minimum of 0.25” clearance is achieved between the lower housing and upper housing. (See illustration above). 9. Fine adjust isolators to level equipment. JOHNSON CONTROLS
FORM 201.28-NM1.1 ISSUE DATE: 8/29/2012 MOUNT TYPE Notes: 1. Use either all CP's or all CP2's at all locations on a unit. ONE INCH DEFLECTION SPRING ISOLATOR �� MODEL NUMBER COLOR CODE �� SECTION 5 - TECHNICAL DATA 2. Installation requires bolting or anchoring mount to support structure with a 2 x 0.625" diameter bolts or 2 x 0.5" diameter concrete anchors. 3. All springs are designed for 50% over-travel. �� CPX-X- JOHNSON CONTROLS 71 �� RATED CAPACITY (FOR UNITS WITH ALL LOAD POINTS LESS THAN 1785 LBS (810 KG) (LBS.) (KG) PART NUMBER CP-1D-510 BLACK Up thru 434 Up thru 197 029-25334-002 CP-1D-900 DARK GREEN 435 thru 765 198 thru 347 029-25334-003 CP-1D-1200 GRAY 766 thru 1020 348 thru 463 029-25334-004 CP-1D-1360 WHITE 1021 thru 1156 464 thru 524 029-25334-005 CP-1D-1785N GRAY/RED 1157 thru 1785 525 thru 810 029-25334-006 MODEL NUMBER COLOR CODE DIMENSION DATA (INCHES) W D L B C T H CP 3 5/8 7-3/4 6-1/2 4-3/4 1/2 5-5/8 C2P 3 5/8 10-1/2 9-1/4 7-3/4 9/16 6 RATED CAPACITY (FOR UNITS WITH ANY LOAD POINT ABOVE 1518 LBS (689 KG) (LBS.) (KG) PART NUMBER C2P-1D-1350 DARK PURPLE Up thru 1148 Up to 521 029-25334-008 C2P-1D-1800 DARK GREEN 1149 thru 1530 522 - 694 029-25334-009 C2P-1D-2400 GRAY 1531 thru 2040 695 - 925 029-25334-010 C2P-1D-2720 WHITE 2041 thru 2312 926 - 1049 029-25334-012 C2P-1D-3570N GRAY/RED 2313 thru 3570 1050 - 1619 029-25334-013 5
Page 1 and 2:
AIR-COOLED SCREW LIQUID CHILLERS IN
Page 3 and 4:
FORM 201.28-NM1.1 ISSUE DATE: 8/29/
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20: FORM 201.28-NM1.1 ISSUE DATE: 8/29/
Page 69: FORM 201.28-NM1.1 ISSUE DATE: 8/29/
Page 75 and 76: FORM 201.28-NM1.1 SECTION 5 - TECHN
Page 77 and 78: FORM 201.28-NM1.1 SECTION 5 - TECHN
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
show all

YVAA Style A Air-Cooled Screw Liquid Chillers ... - Johnson Controls

Create successful ePaper yourself

Delete template?

Save as template?