Simpson Anchors - Anchoring and Fastening Systems - BuildSite.com

More documents

Recommendations

Info

4 CRACKED-CONCRETE SOLUTIONS ANCHORS DESIGNED AND TESTED TO MEET IBC 2006 CRITERIA SET-XP Anchoring Adhesive SET-XP is an anchoring epoxy formulated and tested in accordance with ICC-ES AC308 to meet the requirements of the 2006 IBC. It has been tested with the IXP anchor, threaded rod and rebar. It has proven to offer increased reliability in adverse conditions in cracked and uncracked concrete including proper functioning in cracked concrete under static and seismic loading. SET-XP cures to a teal color for easy identifi cation as an epoxy formulated for Ultimate Strength Design requirements. Page 34 ICC-ES ESR-2508 IXP Anchor The IXP anchor is a uniquely designed torque-controlled adhesive anchor. When used as a system with SET-XP epoxy, the IXP anchor provides high performance and reliability in adverse conditions, including tension and seismic zones where cracks may intersect the anchor. The IXP anchor was designed to perform in accordance with ICC-ES AC308 to meet the requirements of the 2006 IBC. Page 37 ICC-ES pending Torq-Cut Self Undercutting Anchor The Torq-Cut self undercutting anchor is a heavy-duty, high-capacity anchor designed and tested for use in cracked and uncracked concrete under static and seismic loading conditions. It is designed and tested in accordance with ICC-ES AC-193 to meet the requirements of the 2006 IBC. The built-in ring with hardened cutters expands with installation torque forming undercut grooves in the concrete. This interlocking connection between the anchor and the concrete provides superior load carrying capacity. Page 111 ICC-ES pending Strong-Bolt Anchor The Strong-Bolt wedge anchor is specifi cally designed for optimum performance in both cracked and uncracked concrete. It is designed and tested in accordance with ICC-ES AC-193 to meet the requirements of the 2006 IBC. The Strong-Bolt anchor has proven to offer increased reliability in the most adverse conditions, including proper functioning in cracked concrete under static and seismic loads. Page 115 ICC-ES ESR-1771 Titen HD ® Anchor The Titen HD ® heavy-duty anchor is a patented screw anchor designed for use in concrete and masonry applications. This anchor is code tested to provide outstanding performance in cracked and uncracked concrete under both static and seismic conditions. It is designed and tested in accordance with ICC-ES AC-193 to meet the requirements of the 2006 IBC. In addition to being an ideal anchor for a variety of severe structural applications, the non-expansion installation characteristics make it ideal when minimum edge distance and reduced spacing is a concern. Page 119 ICC-ES ESR-2713 TESTED TO MEET IBC ® 2006 C-SAS-2009 © 2009 SIMPSON STRONG-TIE COMPANY INC.
C-SAS-2009 © 2009 SIMPSON STRONG-TIE COMPANY INC. GCN150 Gas-Actuated Nailer The GCN150 is a portable gas-actuated nailer for attaching light-duty fi xtures such as drywall track, furring strips, hat track and angle track to concrete, steel, block and metal deck. The GCN150 uses a 1,300 shot fuel cell and features a 40 pin magazine for high volume productivity. Page 180 EDOT Anchoring Adhesive EDOT Epoxy-Tie ® is an epoxy adhesive formulated to be an economical and high strength alternative for transportation projects. Available in cartridge and bulk packaging, it is an ideal adhesive for threaded rod anchoring and rebar doweling. Page 62 AT10 Anchoring Adhesive AT10 Acrylic-Tie ® adhesive is a 9.6 ounce single tube cartridge that can be dispensed with a commonly available 10 ounce dispensing tool. A special dispensing tool is not required. AT10 adhesive comes with a mixing nozzle and offers the same performance characteristics as the rest of the Acrylic-Tie product line. Page 68 Stainless-Steel Titen ® Concrete & Masonry Screw The new stainless-steel Titen ® screws are ideal for attaching all types of components to concrete and masonry in environments where corrosion is a concern. These screws, available in hex and phillips head styles, combine the versatility of our standard Titen screws with the benefi ts of enhanced corrosion protection. Page 166 CIP-F Paste-Over CIP-F is a fl exible, peelable and fast-curing polyurea paste-over material. It is used to temporarily seal cracks and to secure injection ports over concrete prior to epoxy or urethane foam injection repair. CIP-F can be peeled off at the completion of a crack injection job by pulling on starter tabs initially placed under the top surface of the paste-over at the time of application or by prying under the paste-over. Page 109 CIP Paste-Over CIP is a fast-curing, two-part epoxy paste-over material. It is used to seal cracks and to secure injection ports over concrete prior to epoxy or urethane foam injection repair. CIP sets up hard and can either be left on the concrete or ground or chiseled off at the completion of a crack injection job. Page 109 ADDITIONAL NEW PRODUCTS 5
Page 1 and 2: ��
Page 3: Building Codes Are Changing New Anc
Page 7 and 8: C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 18 and 19: 18 ICC-ES AC308 ULTIMATE STRENGTH D
Page 20 and 21: 20 TREATMENT OF DESIGN METHODS UNDE
Page 22 and 23: 22 EXAMPLE CALCULATION Adhesive Anc
Page 24 and 25: 24 EXAMPLE CALCULATION Mechanical A
Page 30 and 31: 30 EXAMPLE CALCULATION Torque Contr
Page 32 and 33: 32 Continued from page 31. 3 4 ADHE
Page 34: Epoxy Adhesives 34 SET-XP Structur
Page 39: C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 59 and 60:
C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93:
Page 98 and 99:
Vinylester Adhesive 98 VGC Technica
Page 100 and 101:
Crack Injection 100 ETI Injection E
Page 102 and 103:
Crack Injection 102 CRACK-PAC ® 1.
Page 104 and 105:
Crack Injection 104 EPOXY-TIE ® Tr
Page 106 and 107:
Crack Injection 106 CRACK-PAC ® CA
Page 108 and 109:
Crack Injection 108 CRACK-PAC ® In
Page 110 and 111:
110 MECHANICAL ANCHORS Heavy-duty g
Page 112 and 113:
Mechanical Anchors 112 TORQ-CUT Se
Page 114 and 115:
Mechanical Anchors 114 TORQ-CUT Se
Page 116:
Mechanical Anchors 116 STRONG-BOLT
Page 119 and 120:
Page 121:
Page 128 and 129:
Mechanical Anchors 128 TITEN HD ®
Page 130 and 131:
Mechanical Anchors 130 TITEN HD ®
Page 135 and 136:
Page 137 and 138:
Page 144:
Mechanical Anchors 144 WEDGE-ALL ®
Page 147 and 148:
Page 149 and 150:
Page 152 and 153:
Mechanical Anchors 152 SLEEVE-ALL
Page 154:
Mechanical Anchors 154 Drop-In Anch
Page 158 and 159:
Mechanical Anchors 158 DROP-IN Tech
Page 160:
Mechanical Anchors 160 BLUE BANGER
Page 167 and 168:
Page 169 and 170:
Page 176 and 177:
Mechanical Anchors 176 HWA Hollow W
Page 178 and 179:
Mechanical Anchors 178 SWTB Spring
Page 180 and 181:
Gas-Actuated Fastening System 180 G
Page 182 and 183:
Gas-Actuated Fastening System 182 G
Page 184 and 185:
Powder-Actuated Fastening Systems 1
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 210 and 211:
Page 212 and 213:
212 CARBIDE DRILL BITS, CORE BITS &
Page 214 and 215:
Drill Bits 214 SDS-PLUS ® SDS-PLUS
Page 216 and 217:
Drill Bits 216 SPLINE/STRAIGHT SHAN
Page 218 and 219:
Drill Bits 218 DEMOLITION BITS For
Page 220 and 221:
Drill Bits 220 DRILL BIT WARRANTY C
Page 222 and 223:
222 GLOSSARY OF COMMON TERMS OBLIQU
Page 224 and 225:
224 C-SAS-2009 © 2009 SIMPSON STRO
Page 226 and 227:
226 C-SAS-2009 © 2009 SIMPSON STRO
Page 228 and 229:
Anchor Selection Software Anchor De
Page 230 and 231:
NCHORING
Page 232 and 233:
4 Anchoring and Fastening Systems f
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
10 Anchoring and Fastening Systems
Page 240 and 241:
Page 242 and 243:
Page 244:
Page 247 and 248:
F-SAS-CSAS2009 ©2011 Simpson Stron
Page 249:
Page 252 and 253:
Page 254 and 255:
26 W Anchoring and Fastening System
Page 256 and 257:
N N 28 W Anchoring and Fastening Sy
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

Simpson Anchors - Anchoring and Fastening Systems - BuildSite.com

Create successful ePaper yourself

Delete template?

Save as template?