Simpson Anchors - Anchoring and Fastening Systems - BuildSite.com

More documents

Recommendations

Info

12 Anchoring and Fastening Systems for Concrete and Masonry Addendum Adhesive Accessories Two new adhesive dispensing tools designed to provide reliable, trouble-free dispensing of Simpson Strong-Tie Anchor Systems ® adhesives are now available. EDT22S – Manual Dispensing Tool for 22 oz. Epoxy-Tie ® Adhesive Cartridges The EDT22S epoxy adhesive tool features a steel carriage and is engineered for high-volume, continuous use, delivering maximum performance for all 22 oz. Simpson Strong-Tie Anchor Systems adhesives. FEATURES: • 26:1 thrust ratio delivers maximum dispensing power • Double-gripping plates eliminates drive rod slippage • Cartridges snap into place for better alignment • All steel construction for durability ADT30S – Manual Dispensing Tool for 30 oz. Acrylic-Tie ® Adhesive Cartridges The ADT30S features a steel carriage for ultimate durability and is engineered for continuous, high-volume use. FEATURES: • 26:1 thrust ratio • Double-gripping plates eliminates drive rod slippage • Rugged and durable steel construction • Engineered for continuous, high-volume use hole Cleaning Brushes A new 1 5 ⁄ x 6" hole cleaning brush has been added to our broad line of sizes. The ETB12 brush is used for cleaning drilled holes 1 3 ⁄16"–1 3 ⁄8" in diameter prior to adhesive anchor installation. The brushes have a twisted wire handle with nylon bristles. Description ½" x 3" brush (8" total length) 3 ⁄4" x 4" brush (16" total length) 1" x 4" brush (16" total length) 1" x 4" brush (24" total length) ⁄4" x 4" brush (29" total length) 1 ⁄8 x 6" brush (34" total length) Model No. For Anchor/Rebar Diameter (in.) For hole Diameter (in.) Ctn Qty ETB4 ⁄4– ⁄ 3 ⁄ – 7 ⁄ 6 24 ETB6 3 ⁄8– ⁄8 ⁄2– ⁄4 24 ETB8 ⁄ ⁄ – ⁄ 24 ETB8L 3 ⁄ 13 ⁄ – 7 ⁄ 24 ETB10 7 ⁄ – 1– 1 ⁄ 24 ETB12 1 ⁄4 1 ⁄16–1 ⁄8 24 EDT22S ADT30S ETB F-SAS-CSAS2009 ©2011 Simpson Strong-Tie Company Inc.
F-SAS-CSAS2009 ©2011 Simpson Strong-Tie Company Inc. Anchoring and Fastening Systems for Concrete and Masonry Addendum Torq-Cut Self-Undercutting Anchor for Cracked and Uncracked Concrete The Torq-Cut self-undercutting anchor is a heavy-duty, high-capacity anchor designed and tested for use in cracked and uncracked concrete under static and seismic loading conditions. It is designed to meet the stringent requirements of the 2006 and 2009 IBC for post-installed anchors. The built-in ring with hardened cutters expands with installation torque forming undercut grooves in the concrete. This interlocking connection between the anchor and the concrete provides superior load carrying capacity. FEATURES: • Self-undercutting feature provides higher load carrying capacity than conventional mechanical anchors • AC193 code tested to ensure outstanding performance in both cracked and uncracked concrete • Excellent for resisting seismic and vibratory loads • Suitable for seismic applications categories A-F • Ductile steel rod provides consistent, reliable performance • Specially designed, low-friction expansion cone minimizes binding and speeds installation • Installs just like a conventional expansion anchor, no special tool, drill bit, or secondary drilling is required • The head is stamped with the Simpson Strong-Tie ® "≠" sign and size identification for easy post installation verification MATERIAL: ASTM A193 grade B7 or B7M rod with SAE J403 grade 1144 undercut expansion ring and expansion cone FINISh: Zinc plated CODES: ICC-ES pending The load tables list values based upon results from the most recent testing and may not relect those in current code reports. Where additonal local jurisdiction requirements apply, consult the current reports for applicable load values. TEST CRITERIA: The Torq-Cut anchor has been tested in accordance with ICC-ES's Acceptance Criteria for Mechanical Anchors in Concrete Elements (AC193) and ACI 355.2 for the following: • Static tension and shear loading in cracked and uncracked concrete • Seismic and wind loading in cracked and uncracked concrete • Performance in cracked concrete Torq-Cut Setting Tool The TCAST is the steel setting tool used to install the Torq-Cut anchor. It is used to drive the anchor into the pre-drilled hole and protect the threads on the Torq-Cut from being damaged by hammer blows. INSTALLATION: Caution: Oversized holes in the base material will make it dificult to set the anchor and will reduce the anchor’s load capacity. Do not use an impact wrench to set or tighten the Torq-Cut anchor. Installation Instructions: Pre-Set Version 1. Drill a hole in the base material to the specified embedment depth using the appropriate diameter carbide drill bit specified for each diameter. 2. Blow the hole clean using compressed air. 3. Assemble the anchor with nut and washer and finger tighten nut so all components are snug (spacer sleeve, expansion sleeve and cone). The bottom of the threaded rod should be flush with the bottom of the cone. 4. Place the anchor into the drilled hole and use a hammer and setting tool to drive the anchor until the washer and nut are tight against the surface of the base material. 5. Remove the nut and washer and install the fixture. Re-assemble the nut and washer over the fixture. 6. Tighten to the required installation torque. Installation Instructions: Through-Set Version 1. Drill a hole in the base material to the specified embedment depth using the appropriate diameter carbide drill bit specified for each diameter. 2. Blow the hole clean using compressed air. 3. Assemble the anchor with nut and washer and finger tighten nut so all components are snug (spacer sleeve, expansion sleeve and cone). The bottom of the threaded rod should be flush with the bottom of the cone. 4. Place the anchor through the fixture and into the drilled hole. Use a hammer and setting tool to drive the anchor until the washer and nut are tight against the fixture. 5. Tighten to the required installation torque. AppLICATION: Interior environment where low levels of moisture and corrosive chemicals are present SUggESTED SpECIFICATIONS: Self-undercutting anchors shall have an expansion ring with undercutting teeth which expands by tightening the nut that pushes the ring into a cone expander via a spacer sleeve. The anchor shall have been tested and qualiied for performance in cracked and uncracked concrete per ACI 355.2 and ICC-ES AC193. Undercut anchor shall be the Torq-Cut self-undercutting anchor from Simpson Strong-Tie, Pleasanton, CA, and be installed following the Simpson Strong-Tie instructions. TESTED TO MEET Torq-Cut Self-Undercutting Anchor U.S. patent 7,357,613 Installation Sequence Steps 4, 5, 6 – pre-Set Version 4 5 6 Setting Tool Steps 4, 5 – Through-Set Version 4 5 Setting Tool �� Æ �� Torq-Cut Anchor Installation Data Nominal Anchor Dia (in) ⁄ ⁄ ⁄ ⁄ Drill Bit Size (in) ⁄ 7 ⁄ 1 1 ⁄ Min. Fixture Hole Dia Pre-Set (in) Min. Fixture Hole Dia Through-Set (in) Torq-Cut Setting Tool (Sold separately) Steps 1, 2, 3 – pre-Set and Through-Set Version 1 2 3 ⁄ 6 ⁄ 6 ⁄ ⁄ ⁄ 6 ⁄ ⁄ 1 ⁄ Wrench Size (in) ⁄ 6 ⁄4 ⁄ 1 ⁄ Setting Tool Required TCAST37 TCAST50 TCAST62 TCAST75 13
Page 1 and 2:
��
Page 3 and 4:
Building Codes Are Changing New Anc
Page 5 and 6:
C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 18 and 19:
18 ICC-ES AC308 ULTIMATE STRENGTH D
Page 20 and 21:
20 TREATMENT OF DESIGN METHODS UNDE
Page 22 and 23:
22 EXAMPLE CALCULATION Adhesive Anc
Page 24 and 25:
24 EXAMPLE CALCULATION Mechanical A
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
30 EXAMPLE CALCULATION Torque Contr
Page 32 and 33:
32 Continued from page 31. 3 4 ADHE
Page 34:
Epoxy Adhesives 34 SET-XP Structur
Page 39:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93:
Page 98 and 99:
Vinylester Adhesive 98 VGC Technica
Page 100 and 101:
Crack Injection 100 ETI Injection E
Page 102 and 103:
Crack Injection 102 CRACK-PAC ® 1.
Page 104 and 105:
Crack Injection 104 EPOXY-TIE ® Tr
Page 106 and 107:
Crack Injection 106 CRACK-PAC ® CA
Page 108 and 109:
Crack Injection 108 CRACK-PAC ® In
Page 110 and 111:
110 MECHANICAL ANCHORS Heavy-duty g
Page 112 and 113:
Mechanical Anchors 112 TORQ-CUT Se
Page 114 and 115:
Mechanical Anchors 114 TORQ-CUT Se
Page 116:
Mechanical Anchors 116 STRONG-BOLT
Page 119 and 120:
Page 121:
Page 128 and 129:
Mechanical Anchors 128 TITEN HD ®
Page 130 and 131:
Mechanical Anchors 130 TITEN HD ®
Page 135 and 136:
Page 137 and 138:
Page 144:
Mechanical Anchors 144 WEDGE-ALL ®
Page 147 and 148:
Page 149 and 150:
Page 152 and 153:
Mechanical Anchors 152 SLEEVE-ALL
Page 154:
Mechanical Anchors 154 Drop-In Anch
Page 158 and 159:
Mechanical Anchors 158 DROP-IN Tech
Page 160:
Mechanical Anchors 160 BLUE BANGER
Page 167 and 168:
Page 169 and 170:
Page 176 and 177:
Mechanical Anchors 176 HWA Hollow W
Page 178 and 179:
Mechanical Anchors 178 SWTB Spring
Page 180 and 181:
Gas-Actuated Fastening System 180 G
Page 182 and 183:
Gas-Actuated Fastening System 182 G
Page 184 and 185:
Powder-Actuated Fastening Systems 1
Page 186 and 187:
Page 188 and 189:
Page 190 and 191: Powder-Actuated Fastening Systems 1
Page 212 and 213: 212 CARBIDE DRILL BITS, CORE BITS &
Page 214 and 215: Drill Bits 214 SDS-PLUS ® SDS-PLUS
Page 216 and 217: Drill Bits 216 SPLINE/STRAIGHT SHAN
Page 218 and 219: Drill Bits 218 DEMOLITION BITS For
Page 220 and 221: Drill Bits 220 DRILL BIT WARRANTY C
Page 222 and 223: 222 GLOSSARY OF COMMON TERMS OBLIQU
Page 224 and 225: 224 C-SAS-2009 © 2009 SIMPSON STRO
Page 226 and 227: 226 C-SAS-2009 © 2009 SIMPSON STRO
Page 228 and 229: Anchor Selection Software Anchor De
Page 230 and 231: NCHORING
Page 232 and 233: 4 Anchoring and Fastening Systems f
Page 238 and 239: 10 Anchoring and Fastening Systems
Page 244: 16 Anchoring and Fastening Systems
Page 247 and 248: F-SAS-CSAS2009 ©2011 Simpson Stron
Page 249: F-SAS-CSAS2009 ©2011 Simpson Stron
Page 254 and 255: 26 W Anchoring and Fastening System
Page 256 and 257: N N 28 W Anchoring and Fastening Sy
show all

Simpson Anchors - Anchoring and Fastening Systems - BuildSite.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?