Simpson Anchors - Anchoring and Fastening Systems - BuildSite.com

More documents

Recommendations

Info

Mechanical Anchors 120 TITEN HD ® Titen HD ® Anchor Product Data - Zinc Plated Size (in.) Model No. FIXTURE HOLE DIAMETER: Due to the full shank diameter and larger threads of the Titen HD ® screw anchor, consideration needs to be given to specifying the appropriate diameter Titen HD anchor based on the fi xture hole type to be used. The American Institute of Steel Construction (AISC) has established the following guidelines with regards to fi xture hole sizing depending on the hole type: • “Standard” fi xture holes are ¹⁄₁₆" larger than the nominal anchor diameter. • “Oversized” fi xture holes are ¹⁄₈ -³⁄₁₆" larger than the nominal anchor diameter, depending upon the specifi c anchor diameter. Standard fi xture hole Heavy Duty Screw Anchor for Concrete and Masonry Drill Bit Dia. (in.) Wrench Size (in.) Quantity Box Carton ³⁄₈ x 3 THD37300H 50 200 ³⁄₈ x 4 ³⁄₈ x 5 THD37400H THD37500H ³⁄₈ ⁹⁄₁₆ 50 50 200 100 ³⁄₈ x 6 THD37600H 50 100 ¹⁄₂ x 3 THD50300H 25 100 ¹⁄₂ x 4 THD50400H 20 80 ¹⁄₂ x 5 THD50500H 20 80 ¹⁄₂ x 6 THD50600H 20 80 ¹⁄₂ x 6¹⁄₂ ¹⁄₂ x 8 THD50612H THD50800H ¹⁄₂ ³⁄₄ 20 20 40 40 ¹⁄₂ x 12 THD501200H 20 40 ¹⁄₂ x 13 THD501300H 20 40 ¹⁄₂ x 14 THD501400H 20 40 ¹⁄₂ x 15 THD501500H 20 40 ⁵⁄₈ x 4 THD62400H 10 40 ⁵⁄₈ x 5 THD62500H 10 40 ⁵⁄₈ x 6 THD62600H ⁵⁄₈ ¹⁵⁄₁₆ 10 40 ⁵⁄₈ x 6¹⁄₂ THD62612H 10 40 ⁵⁄₈ x 8 THD62800H 10 20 ³⁄₄ x 4 THD75400H 10 40 ³⁄₄ x 5 THD75500H 5 20 ³⁄₄ x 6 ³⁄₄ x 7 THDT75600H THD75700H ³⁄₄ 1¹⁄₈ 5 5 20 10 ³⁄₄ x 8¹⁄₂ THD75812H 5 10 ³⁄₄ x 10 THD75100H 5 10 1. Zinc plating meets ASTM B633, SC1. 2. Length is measured from the underside of the head to the tip of the anchor. Oversized fi xture hole Use the following table to identify which diameter Titen HD ® screw anchor to use based on the fi xture hole type and diameter. In most cases where a smaller diameter Titen HD anchor is called out in comparison to the competitor's larger diameter anchor, the Titen HD anchor still generally provides allowable tension and shear load values comparable to or greater than those of the competitor's anchor. Titen HD Anchor Product Data - Mechanically Galvanized Size (in.) Model No. Drill Bit Dia. (in.) Wrench Size (in.) Quantity Box Carton ³⁄₈ x 5 ³⁄₈ x 6 THD37500HMG THD37600HMG ³⁄₈ ⁹⁄₁₆ 50 50 100 100 ¹⁄₂ x 5 THD50500HMG 20 80 ¹⁄₂ x 6 ¹⁄₂ x 6¹⁄₂ THD50600HMG THD50612HMG ¹⁄₂ ³⁄₄ 20 20 80 40 ¹⁄₂ x 8 THD50800HMG 20 40 ⁵⁄₈ x 5 THD62500HMG 10 40 ⁵⁄₈ x 6 ⁵⁄₈ x 6¹⁄₂ THD62600HMG THD62612HMG ⁵⁄₈ ¹⁵⁄₁₆ 10 10 40 40 ⁵⁄₈ x 8 THD62800HMG 10 20 ³⁄₄ x 8¹⁄₂ ³⁄₄ x 10 THD75812HMG THD75100HMG ³⁄₄ 1¹⁄₈ 5 5 10 10 1. Mechanical galvanizing meets ASTM B695, Class 65, Type 1. Intended for some pressure-treated wood sill plate applications. Not for use in other corrosive or outdoor environments. See page 16 for more corrosion information. Hole Dimensions Titen HD Diameter (in.) Wrench Size (in.) The Titen HD ® screw anchor ³⁄₄ x 6 and ³⁄₄ x 7 (models THDT75600H and THD75700H) have a 1" section under the head that is unthreaded to allow installation into tilt-up wall braces. Recommended Fixture Hole Size (in.) ³⁄₈ ⁹⁄₁₆ ¹⁄₂ to ⁹⁄₁₆ ¹⁄₂ ³⁄₄ ⁵⁄₈ to ¹¹⁄₁₆ ⁵⁄₈ ¹⁵⁄₁₆ ³⁄₄ to ¹³⁄₁₆ ³⁄₄ 1¹⁄₈ ⁷⁄₈ to ¹⁵⁄₁₆ Reinstallation of Titen HD ® screw anchor in Original Drilled Hole Titen HD anchors may be removed and reinstalled in the original hole without reducing load capacity if the threads that were cut into the concrete during the original installation are followed. Start reinstallation of the anchor by hand to prevent cross-threading and a possible reduction in load capacity. C-SAS-2009 © 2009 SIMPSON STRONG-TIE COMPANY INC.
C-SAS-2009 © 2009 SIMPSON STRONG-TIE COMPANY INC. TITEN HD ® Heavy Duty Screw Anchor for Concrete and Masonry Titen HD ® Installation Information and Additional Data 1,4 Characteristic Symbol Units Installation Information Nominal Anchor Diameter (inch) ³⁄₈ 4 ¹⁄₂ ³⁄₄ Drill Bit Diameter d in. ³⁄₈ ¹⁄₂ ³⁄₄ Baseplate Clearance Hole Diameter d c in. ¹⁄₂ ⁵⁄₈ ⁷⁄₈ Maximum Installation Torque Tinst,max ft-lb 50 2 65 2 150 2 Maximum Impact Wrench Torque Rating Timpact,max ft-lb 150 3 385 3 385 3 Embedment Depth hnom in. 2¹⁄₂ 3¹⁄₄ 3¹⁄₄ 4 5¹⁄₂ 6¹⁄₄ Critical Edge Distance cac in. 2¹¹⁄₁₆ 3⁵⁄₈ 3⁹⁄₁₆ 4¹⁄₂ 6³�₈ 7⁵⁄₁₆ Minimum Edge Distance cmin in. 1³⁄₄ Minimum Spacing smin in. 3 Minimum Concrete Thickness hmin in. 3³⁄₄ 5 5 6¹⁄₄ 8³⁄₄ 10 Additional Data Anchor Category category - 1 Yield Strength fya psi 97,000 Tensile Strength futa psi 110,000 Minimum Tensile & Shear Stress Area Ase in 2 0.099 0.183 0.414 Axial Stiffness in Service Load Range - Uncracked Concrete βuncr lb/in. 715,000 Axial Stiffness in Service Load Range - Cracked Concrete βcr lb/in. 345,000 1. The information presented in this table is to be used in conjunction with the design criteria of ACI 318 Appendix D. 2. T inst,max is the maximum permitted installation torque for the embedment depth range covered by this table. This is not applicable to other embedment depths published elsewhere in this catalog. 3. Timpact,max is the maximum permitted torque rating for impact wrenches for the embedment depth range covered by this table. This is not applicable to other embedment depths published elsewhere in this catalog. 4. This data at h nom = 2¹⁄₂" is also valid for the THD50234RH installed at hnom = 2³⁄₄". See page 133 for further information regarding the THD50234RH. Mechanical Anchors 121
Page 1 and 2:
��
Page 3 and 4:
Building Codes Are Changing New Anc
Page 5 and 6:
C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 18 and 19:
18 ICC-ES AC308 ULTIMATE STRENGTH D
Page 20 and 21:
20 TREATMENT OF DESIGN METHODS UNDE
Page 22 and 23:
22 EXAMPLE CALCULATION Adhesive Anc
Page 24 and 25:
24 EXAMPLE CALCULATION Mechanical A
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
30 EXAMPLE CALCULATION Torque Contr
Page 32 and 33:
32 Continued from page 31. 3 4 ADHE
Page 34:
Epoxy Adhesives 34 SET-XP Structur
Page 39:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 75 and 76: C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 93: C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 98 and 99: Vinylester Adhesive 98 VGC Technica
Page 100 and 101: Crack Injection 100 ETI Injection E
Page 102 and 103: Crack Injection 102 CRACK-PAC ® 1.
Page 104 and 105: Crack Injection 104 EPOXY-TIE ® Tr
Page 106 and 107: Crack Injection 106 CRACK-PAC ® CA
Page 108 and 109: Crack Injection 108 CRACK-PAC ® In
Page 110 and 111: 110 MECHANICAL ANCHORS Heavy-duty g
Page 112 and 113: Mechanical Anchors 112 TORQ-CUT Se
Page 114 and 115: Mechanical Anchors 114 TORQ-CUT Se
Page 116: Mechanical Anchors 116 STRONG-BOLT
Page 119: C-SAS-2009 © 2009 SIMPSON STRONG-T
Page 128 and 129: Mechanical Anchors 128 TITEN HD ®
Page 130 and 131: Mechanical Anchors 130 TITEN HD ®
Page 144: Mechanical Anchors 144 WEDGE-ALL ®
Page 152 and 153: Mechanical Anchors 152 SLEEVE-ALL
Page 154: Mechanical Anchors 154 Drop-In Anch
Page 158 and 159: Mechanical Anchors 158 DROP-IN Tech
Page 160: Mechanical Anchors 160 BLUE BANGER
Page 176 and 177:
Mechanical Anchors 176 HWA Hollow W
Page 178 and 179:
Mechanical Anchors 178 SWTB Spring
Page 180 and 181:
Gas-Actuated Fastening System 180 G
Page 182 and 183:
Gas-Actuated Fastening System 182 G
Page 184 and 185:
Powder-Actuated Fastening Systems 1
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 210 and 211:
Page 212 and 213:
212 CARBIDE DRILL BITS, CORE BITS &
Page 214 and 215:
Drill Bits 214 SDS-PLUS ® SDS-PLUS
Page 216 and 217:
Drill Bits 216 SPLINE/STRAIGHT SHAN
Page 218 and 219:
Drill Bits 218 DEMOLITION BITS For
Page 220 and 221:
Drill Bits 220 DRILL BIT WARRANTY C
Page 222 and 223:
222 GLOSSARY OF COMMON TERMS OBLIQU
Page 224 and 225:
224 C-SAS-2009 © 2009 SIMPSON STRO
Page 226 and 227:
226 C-SAS-2009 © 2009 SIMPSON STRO
Page 228 and 229:
Anchor Selection Software Anchor De
Page 230 and 231:
NCHORING
Page 232 and 233:
4 Anchoring and Fastening Systems f
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
10 Anchoring and Fastening Systems
Page 240 and 241:
Page 242 and 243:
Page 244:
Page 247 and 248:
F-SAS-CSAS2009 ©2011 Simpson Stron
Page 249:
Page 252 and 253:
Page 254 and 255:
26 W Anchoring and Fastening System
Page 256 and 257:
N N 28 W Anchoring and Fastening Sy
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
show all

Simpson Anchors - Anchoring and Fastening Systems - BuildSite.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?