Tender Notice for Purchase of Medical Equipments - Dadra and ...

On Line Tender Notice No.47of 2012-13
Administration of Dadra & Nagar Haveli, U.T.,
Office of the Medical Superintendent,
Shri Vinoba Bhave Civil Hospital
No. MS/VBCH/2012-13/ME/69/6632 Silvassa.
e-Tender Notice
Date:16.10.2012
Tender for Purchase of Medical Equipments for Shri Vinoba Bhave Civil
Hospital, Dadra & Nagar Haveli, Silvassa.
The Medical Superintendent, Shri Vinoba Bhave Civil Hospital, Dadra &
Nagar Haveli, Silvassa on behalf of President of India, invites on line tender on
https://dnh.nprocure.com from the Manufactures/Authorized Dealers/Suppliers for
supply of below mentioned equipment.
Sr.
No.
Particulars EMD
1.
Purchase of Medical Equipments for Shri Vinoba
Bhave Civil Hospital
a. Cardiology Equipments `.88,750/b.
Neonatology Equipments `.1,63,000/c.
Ophthalmology Equipments
1. Under VBCH `.87,500/-
2. Under DBCP `.50,000/d.
Dermatology Equipments `.63,050/e.
Pathology Equipments `.1,02,750/f.
Orthopedic Equipments `.1,14,250/g.
Physiotherapy Equipments `.2,21,500/h.
ENT Equipments `.1,43,000/i.
Urology Equipments `.11,250/j.
CSSD Equipments `.60,750/k.
General Equipments `.26,000/l.
Solar Water Heater Plant `.1,00,000/m.
Instruments `.50,000/-
Tender
Fees
`.2000/-
Non – Refundable

Bid document downloading Start Date : 17.10.2012
Bid document downloading End Date : 06.11.2012, 15:00 Hrs.
Last Date & Time for receipt of Bid : 07.11.2012, 11.00 Hrs.
Preliminary Stage Bid Opening Date : 07.11.2012, 11.10 Hrs
Technical Stage Bid Opening Date : 07.11.2012, 11.30 Hrs
Commercial Stage Bid Opening Date : 10.11.2012, 12.00 Hrs
Bidders have to submit price bid in Electronic format only on
https://dnh.procure.com website till the last date and time for submission. Price Bid in
Physical format shall not be accepted in any case.
Bid submission should be done along with tender Fees and EMD in original
by R.P.A.D./Speed Post in the office of the undersigned. However, Tender Inviting
Authority shall not be responsible for any postal delay.
1. The Tender Fees should not be forwarded by cash.
2. The Tender fees will be accepted only in form of DD/A/c payee Cheque of
any Nationalized or Scheduled Bank of India payable in Silvassa.
3. The EMD will be accepted in form of FDR /A/c Payee Demand Draft /
Bankers Cheque or Bank Guarantee from any commercial banks in an
acceptable form payable at silvassa in favor of under signed.
4. The EMD should not be forwarded by cash.
The tender inviting authority reserves the right to accept or reject any or all the
tender to be received without assigning any reasons thereof.
In case bidder needs any clarification of if training required for participating in online
tender, they can contact the following office. “(n) Code Solution –A Division, GNFC
Ltd.” 403, GNFC info Tower, Bodakdev, Ahmedabad – 380 054, Gujarat (India) Email
: nprocure@gnfc, Net Fax :+97 7926857321, Website : www.nprocure.com.
Medical Superintendent
Shri Vinoba Bhave Civil Hospital
Dadra & Nagar Haveli
Silvassa.

Copy to :-
1) PS to Hon’ble Administrator, Dadra & Nagar Haveli, Silvassa for information.
2) P/A to Secretary (Health), Dadra & Nagar Haveli, Silvassa for information
3) All Heads of Office, Dadra & Nagar Haveli, Silvassa for information & n.a.
4) CPO, Dadra & Nagar Haveli, Silvassa for wide publicity in Newspaper.
5) Director General, Indian Trade Journal, Kolkata for publication on Newspaper.
6) NIC, Dadra & Nagar Haveli, Silvassa with a request to publish in Website.
7) The Deputy Director (OL), Dadra & Nagar Haveli, Silvassa for translation in
Hindi.
8) Accounts Section, Shri VBCH, Silvassa for information
9) Central Store, Shri VBCH, Silvassa for Information.
Medical Superintendent
Shri Vinoba Bhave Civil Hospital
Dadra & Nagar Haveli
Silvassa.

U.T. ADMINISTRATION OF DADRA & NAGAR HAVELI,
OFFICE OF THE MEDICAL SUPERINTENDENT,
SHRI VINOBA BHAVE CIVIL HOSPITAL,
SILVASSA
Terms and Conditions for the “Purchase of Medical Equipments” for
Shri Vinoba Bhave Civil Hospital, Dadra & Nagar Haveli, Silvassa.
� Instructions to Bidders :
1) The rate should be quoted in the prescribed form given by the
department; the rate should be valid upto One Year from the
date of tenderization.
2) All/Taxes/Duties/Royalties Charges payable on the sales/transport
etc. within and/or outside the state shall be payable by the
supplier.
3) Where specifications/make/manufacture is not specified by this
office, the rates should be quoted only for the 1 st class and
standard quality only.
4) The tenderer should specify the name of the manufacturer and
complete specification for the items quoted to be submitted in
the Technical Bid.
5) The decision of the Tender Inviting Officer for
acceptance/rejection of any articles supplied including the
decision for equivalent specifications, standard and quality etc. of
articles shall be final.
6) The Tenderer should enclose along with tender the Earnest
Money Deposit in form of Fix Deposit Receipt/Account Payee
Demand Draft/Banker’s Cheque or Bank Guarantee from any of
the Commercial Banks in an acceptable form payable at Silvassa
in favour of Medical Superintendent, Shri Vinoba Bhave Civil
Hospital, Silvassa. The EMD should not be forwarded by Cash.

Tender received without Earnest Money Deposit will be summarily
rejected.
7) (a) The successful tenderer will have to pay within 10 days from
the date of demand, an amount equal to 10% of the total value of
articles, which may be ordered, as the amount of security deposit.
(b) Non receipt of Security Deposit within stipulated time will
result in automatic cancellation of the order for supply without
any intimation.
(c) However in case if any articles are received for which the
Security Deposit may not have been deposited, the full Security
Deposit as may be due from the supplier will be recovered from
the bill(s) for such articles.
8) The amount of Earnest Money paid by the successful Tenderer(s)
will be adjusted against the amount of Security Deposit to be paid
by the successful tenderer(s) as per condition No.07 above.
9) The tender should be neatly typed or hand written only on letter
head carries the name of supplier and the signature of the
tenderer. No overwriting, correction or erasures will be
considered.
10) All bills should be in TRIPLICATE and should invariably mention the
number and date of supply order.
11) All bills for amount above `.5000/- should be pre-receipted on a
Revenue Stamp of proper value. Bills for amount exceeding
`.5000/- not pre-receipted on Revenue Stamp of proper value will
not be accepted for payment.
12) Each bill in which Sales Tax is charged must contain the following
certificates on the body of the bill: “CERTIFIED” that the goods on
which Sales Tax has been charged have not been exempted under
the Central Sale Tax Act or the Rules made there under and the
amount charged on account of Sales Tax on these goods is not
more than what is payable under the provisions of relevant Act or
Rules made there under”.

13) The Tenders shall be submitted in two-bid system, wherein the
Technical bid and Commercial Bid is to be filled in
www.nprocure.com and the EMD and Tender Fee has to be
submitted in Tender Box along with a covering letter. The
envelope should be super scribing on the envelope as “Sealed
Cover of Bid- Purchase of Medical Equipments for Shri Vinoba
Bhave Civil Hospital”. The EMD and Tender Fees should be
enclosed with BID only. The last date of submission will be
10.09.2012 upto 11.00 hours.
14) The right to accept or reject without assigning any reasons or all
tenders in part or whole is reserved with the Tender Inviting
Officer and his decision(s) on all matters relating to acceptance or
rejection of the tenders as a whole or in part will be final and
binding to all.
15) If the tenderer whose tender is accepted, fails to execute the
supply order within stipulated time the Earnest Money Deposit of
such tenders will stand forfeited to the Government.
16) In case, the supplier does not execute the supply order placed
with him, the EMD of the supplier will be forfeited to the
Government and the contract for the supply shall terminated with
no further liabilities on either party to the contract.
17) No separate agreement will be required to be signed by the
successful tender(s) for the purpose of this contract for supply.
Rates tendered/offered in response to the concerned Tender
Notice shall be considered as acceptance of all above terms and
conditions for supply for all legal purpose.
18) The tender will be accepted during working hours upto 10.09.2012
at 11.00 hours and will open on the same day if possible in the
office of the Medical Superintendent, Shri Vinoba Bhave Civil
Hospital, Silvassa.

� Conditions of Contract :
1) The rate(s) quoted should be strictly for free delivery at FOR
Silvassa and will be valid and operative for supply orders issued
within one year from the date of invitation of tenders.
2) Orders once placed should be delivered within the given time
period and item should be door delivered.
3) No extra charge for packing, forwarding and insurance etc. will be
paid on the rates quoted.
4) The rates should be quoted only for the items specified in the list
of requirement and should be for the items of given special
make/manufacture.
5) Rates quoted for items other than the required
specification/make/manufacture will not be considered.
6) The amount of Earnest Money paid by the tenderer(s) whose
tenders are not accepted will be refunded to them by cheque or
Demand Draft (as may be convenient to the Tender Inviting
Officer if the amount is above `.200/-) drawn on any branch of
State of India or its subsidiary Commercial Bank. Where this mode
of payment is not possible the amount will be refunded at the cost
of the tenderer.
7) Only on satisfactory completion of the supply order for and on
payment of all bills of the supplier, as to be admitted for payment,
the amount of Security Deposit/Earnest Money will be refunded
after expiry of guarantee/warranty period, if any, or any such
date/period as may be mutually agreed upon.
8) The tender inviting officer will consider extension of time for
remitting the Security Deposit as demanded. However, in case of
denial to consider such extension the supplier is bound to abide
by the limit given and liable to make good for the loss made to the
Government on account of his failure to abide by the time limit.

9) Railway Receipt or other transport document should be drawn in
the favor of Officer Inviting tender.
10) Railway Receipt or other transport document should not be send
by VPP or through any Bank as this being a Government Office it is
not possible to clear cash demands of Post Office/Bank for
delivery of RR or other transport documents unless we have
agreed to it as special arrangement.
11) The supplies, materials etc. of inferior quality standard or of
different specifications, brand, manufacturer etc other than that
ordered specified and/or incomplete or broken articles will not be
accepted. The supplier has to replace the same at his own cost
and risk. Intimation of non-acceptance of any materials etc will be
sent to the supplier within 10 days from the date of receipt of the
stores and the same will be returned to the supplier at his own
cost and risk, if he so desires and intimates accordingly within 15
days from the date of dispatch of intimation of the nonacceptance.
However, if no communication is received within 15
days from the date of communication the tender Inviting Officer
will not be responsible for any damages, loss etc. of such rejected
articles.
12) In case of failure to replace the accepted and rejected articles
from the supplies made, as mentioned in the conditions the loss
undergone by the Government will be recovered from the
suppliers Security Deposit/Earnest Money or payment due of any
bill(s) to the extend required.
13) In case of failure to supply the store, materials etc. ordered for, as
per conditions and within the stipulated time, the name articles
will be obtained from the tenderer who offered next higher rates
or from any other sources, as may be decided by the tender
inviting Officer and the loss to the Government on account of such
purchases(s) shall be recovered from the former suppliers Security
Deposit/Earnest Money or bills payable. The suppliers shall have
no right to dispute with such procedure.

14) Extension of time limit for supplies shall be considered by the
Tender Inviting Officer. The extension so granted may be with levy
of compensation for delay in execution of supply order up to 5%
of the cost of supplies ordered for at the discretion of the
authority competent to grant extension of time limit provided
such request is made well in time, depending upon the
circumstances and such decision in the matter will be final.
15) Demurrage charges paid by the Tender Inviting Officer on account
of delayed receipt of dispatch documents intimation will be
recovered from the bills payable to the supplier.
16) If at any time after the order for supply of materials the Tender
Inviting Officer shall for any reason whatsoever not require the
whole or part of the quantity thereof as specified in the order the
Tender Inviting Officer shall give notice in writing of the fact to the
supplier(s) who shall have to claim to any payment of
compensation what so ever on account of any profit or advantage
which the supplier(s) might have derived from the supply of
articles in full, but which did not derive in consequence of the full
quantity of articles not having been purchased, nor shall have any
claim for compensation by reasons of any alterations having been
made in the original instructions which shall invoice any
curtailment of the supply originally contemplated.
17) The Earnest Money(s)/Security Deposit(s) paid by the tender(s)
earlier against any tender(s) or supply order(s) is/are not
adjustable with Earnest Money or Security Deposit required by
these conditions.
18) The tenders/offers received do not confirm with the terms and
conditions of this office will be summarily rejected. If any firm
desires to consider exemption from payment of Earnest Money
Deposit, certified copies of its Registration with D.G.S. & D. should
be attached to their tenders.
19) The items as mentioned in the list are the approximate estimates
invited and actual purchase may more. Accordingly the successful
tenderer has no right for any loss/damages with reference to

approximate requirement shown in tender and actual
requirement.
20) Supplier may ensure the goods at his own cost to safeguard the
delivery of such goods dispatched by him to the consignee; the
department will not be responsible for the damages or pilferage
of goods during transit.
21) The tenderer should attached copies of certificate of
• Experience in the field of selling of similar Medical
Equipments,
• Proof of fulfilling the norms of IS/ISO/CE specification if
any,
• Copy of dealership letter (as per Annexure 15) ,
• License for import,
• PAN No.,
• Catalog of the item quoted etc.
• Documentary evidence of their previous experience in
carrying out similar supply and of their eligibility in support
of their claim for consideration in the matter of award of
contract
22) The manufacturing units who are placed in Silvassa are exempted
for Earnest Money Deposit.
23) Rates should be quoted in the forms issued from the department
and as per the requirement asked for. Rates quoted are for Shri
Vinoba Bhave Civil Hospital, Silvassa.
24) The tender should furnish a declaration regarding the
Blacklisting/Debarring to participate in the Government tender on
the letter head. If the information provided found false the tender
will be rejected and EMD shall be forfeited.
25) As and when necessary, any employee of this institution shall be
given training for the use of equipments by the supplier at their
cost.

26) The tender document shall be duly signed by the supplier.
27) The Tenderer has to submit the authorization letter from the
principal manufacturing company as per the format prescribed in
Annexure 14.
28) Training of the Medical Equipments will be borne by the
successful bidder as follows:
a. Training for Medical Specialists at other centre under purview
of a trained doctor outside Silvassa
b. Training for Medical Equipments of Para-medical staff in Shri
VBCH
Signature & Designation of
Tender Inviting Officer…
Medical Superintendent
Shri Vinoba Bhave Civil Hospital
Dadra & Nagar Haveli
Silvassa.
The above terms and conditions are accepted and are binding to me/us.
Place: Signature of tenderer
Dated: Name of tenderer with seal of the
firm
NOTE: Please return One Copy of these terms and conditions duly
signed with seal of firm along with the tender.
Place: Signature of tenderer
Dated: Name of tenderer with seal of the
firm

� Schedule of Requirements, Specifications and Allied
Technical Details:
The Specifications are mentioned on respective Annexure, the bidder has to
fill the relevant annexure duly stamped and signed. Any deviation from the
mentioned specification has to be mentioned in the Annexure-15.
S.N Name of Equipment Mfg Company Preferred Qty Annexure
Medicine
1
Temporary Pacemaker
APC/Maquet/Medtronic/
Biotronic
5 1
2 12 Lead ECG Machine GE/L&T/BPL/Alan 3 1
3 Cardiac Stress Test Machine GE/Allengers/BPL 1 1
4 External Defibrillator
Nihon Kohden/Philips/
GE/Mindray
1 1
5 Internal Defibrillator
Meditronics/Biotronics/St
Jude Medical /Boston Sci.
1 1
6 Holter with Ambulatory BP Vasomedical/Mortara/GE 1 1
Pediatric & Neonatology
Radiant Heat Warmer with
1
resuscitation unit
2 LED Phototherapy
Neotech/Bird
Meditech/Meditrin/Fanem
Neotech/Bird
Meditech/Fanem
9 2
2 2
3 Neonatal Ventilator Drager/GE/Philips 2 2
4 3 Para Monitor Philips/GE/Draeger 1 2
5
Vein Vision device
Dr Morepen/ Abott/Nice
Neotech 1 2
6 Electronic Weight Machine Zeal/SPI/ Accord 2 2
7 CPAP Machine Fisher & Paykel/ Viasys/Fanem 2 2
Ophthalmology
Under VBCH
1 Nd-Yag Laser Lumenis/Opto/Lynton 1 3
2 Fundus Camera
Under DBCP
Biomedix/Leica/Karl Kaps/
Karl Zeiss
1 3
1 Ophthalmic Microscope
Karl Kaps/Karl Zeiss/Moller
Wedel
1 3
2 Cryomachine Basco/Kohden/Leica 1 3
3 Automated perimeter
Topcon/Zeiss/Medmont/
Humphrey/Appasamy
1 3

S.N Name of Equipment Mfg Company Preferred Qty Annexure
Dermatology
1 IPL Laser with RF Derma India/Lumenis/Lynton 1 4
2 Q-Switched Laser Derma India/Lumenis/Lynton 1 4
3 Ultrasonic Face Lift Derma India/Krupa Mediscan 1 4
4 Diode Laser Derma India/ Lumenis/ Lynton 1 4
5 Digital Ionotophoresis Derma India/Krupa Mediscan 1 4
Pathology
1
1
Automated Coagulation
Analyzer Span/Ark/Tulip/Tranasia
1 5
Fully Automated three part
cell counter (18 para)
Span/Ark/Tulip/Tranasia 1 5
2 Binocular Microscope Nikon/Olympus/Zeiss 1 5
3 Rotary Shaker Remi/Standard Company 1 5
4
Four Door Vertical
Refrigerator
Automated System For
Bluestar/Voltas 1 5
5
Identification And Antibiotic
Susceptibility Testing of
Micro Organisms
Biomerieux/Siemens/BD 1 5
6 Automated Slide Stainer
Thermo
Scientific/Sakura/Neutec
1 5
7 Balance Weight Machine Metlar Tolado/Biomerieux 1 5
Orthopedic
1
Battery Operated Drill
Machine Microaire/Stryker/Synthes
2 Hohman Variable retractors
Kalelkar/Synthes/
Teknomedical/Shushrut/Inor
3 Bone Punches
Kalelkar/Synthes/
Teknomedical/Shushrut/Inor
Kalellkar/
4 Peripheral Nerve Locator Synthes/Teknomedical/
Shushrut/Inor
5
Broken screw removal set
(Hollow will) Synthes/Zimmer
6
7
Minimally invasive& miniopen
Discectomy andfusion
system for both cervical and
thoracolumbar use.
Meditronic/Teknomedical/
SMPL/Inor
RF Electrode for Mitek VAPR
System Depuy Mitek
1 6
1
1
1
1
1
5
6
6
6
6
6
6

S.N Name of Equipment Mfg Company Preferred Qty Annexure
8 Flexible Reamer Manman 1 6
9
Wire Cutter tungsten tip
with 2mm wire cutter Synthes/Zimmer/Inor
1
6
10
Sepectrum Instrument
Shoulder Arthos
Codman/Depuy
Mitek/Kallelkar
1
6
11 Monopolar Cautery Cords Galtron/Standard Company 1 6
12 Pencil Drill for Hand Surgery Manman/Medtronic/Codman 1 6
13 Centrifuge- 1800 rpm Remi/Standard Company 1 6
14 Bipolar Cautery Cords Galtron/Standard Company 1 6
15
High definition Camera
System with Xenon Light
Source, 3 chip camera, light
cable (thicker & longer),
video imaging capturing
device
Physiotherapy
1 Isokinetic System
Karl Storz/
Olympus/Maxer/Richard
Wolf/Stryker 1 6
Biotech/ BTE
Technologies/Contrex 1 7
2 Cryotherapy Unit Biotech/ Zimmer/Physiomed 1 7
3 Multi CPM Unit DJO Global/Ormed 1 7
4 Microwave Diathermy Biotech/ Physiomed 1 7
5 Exercise Bike Proxomed/Scifit
Biotech/ Alay Medins/Dev
1 7
6 Trapeze
rehab
Biotech/Alay medins/Dev
1 7
7 4 Channel TENS
rehab/Bionics 1 7
8 Bolsters Biotech/ Alay Medins 1 7
9 Wobble Board Theraband/ Alay Medins 1 7
10
11
High Frequency Chest Wall
Oscillations- Adult &
Pediatric
Biotech/ Electromed/
Respironics/ Philips 1 7
Positive Expiratory Pressure-
Adult & Pediatric Biotech/ Micro 1 7
12 Therassist G5 Biotech/G5 1 7
ENT
1
2
Operating Microscope for
ENT, Plastic, Neuro and
spine.
Nasal Endoscope adult 0
degree 4mm
Karl Zeiss/ Karl Kaps/ Olympus 1 8
Olympus/Richard Wolf/Karl
Storz/Maxer/Fujinon
1 8

S.N Name of Equipment Mfg Company Preferred Qty Annexure
3
4
5
Nasal Endoscope pediatric 0
degree 2.7mm
Nasal Endoscope Adult 30
degree 4 mm
Nasal Endoscope Pediatric
30 degree 2.7mm
Laparoscopy & Urology
1 Ureteroscope
Neonatal/Pediatric
2 Resectoscope
Olympus/Richard Wolf/Karl
Storz/Maxer/Fujinon
Olympus/Richard Wolf/Karl
Storz/Maxer/Fujinon
Olympus/Richard Wolf/Karl
Storz/Maxer/Fujinon
1 8
1 8
1 8
Karl Storz/Olympus/Fujinon/
Richard Wolf 1 9
Karl Storz/Olympus/Fujinon/
Richard Wolf
1
9
CSSD
1 Drying Machine
Tuttaneur/Steridium/Steelco/
Taxus
Steridium/Charmie/Memmert
1 10
2 Incubator
/Medicarft Eqpt. 1 10
3 ETO Taxus/Steridium/3M/PCI 1 10
4 Auto Control Panel for
Autoclave Modi/Shrijee Surgical
2 10
General
1 Fogging Machine
Galtron/J&J/PCI/Radiant/
Idealine/Skan/Aspee
Omron/
7 11
3 Nebulizer
Nulife/Morepen/Philips 10 11
4 Fetal Doppler Teksonic/BPL/Galtron
Nulife/Omron/Metco/Mehta
4 11
5 Needle Destroyer
Surg.
Brightlite/Supreme/Hira/
20 11
6 Suction Machine
Galtron/SPI/Anand 5 11
7 Autoprocessor Prognosys/Chayyagraphics 1 11
8 Solar Water Heater Plant Any Standard Company 1 12
9 Instruments Kalelkar/Inor/Adler/Uma 1 13
The bidders can provide answers by placing the following codes to the right of each
requirement description. Additional information if necessary or helpful can be
included as an attachment. (Format as an Annexure)
Code Meaning
Y Yes. Requirement is met completely
N No. Cannot perform this function and neither an enhancement is planned nor a
modification is proposed.
D Function is present but with slight modification. The deviation has to be mentioned in the
deviation column.

� Price Schedules:
S.N Name of Equipment Mfg Co.
Medicine
Temporary
1
Pacemaker
2 12 Lead ECG Machine
Cardiac Stress Test
3
Machine
4 External Defibrillator
5 Internal Defibrillator
Holter with
6
Ambulatory BP
Pediatric & Neonatology
1
Radiant Heat Warmer
with resuscitation unit
2 LED Phototherapy 2
3 Neonatal Ventilator 2
4 3 Para Monitor 1
5 Vein Vision device 1
6
Electronic Weight
Machine
2
7 CPAP Machine 2
Ophthalmology
Under VBCH
1 Nd-Yag Laser 1
2 Fundus Camera 1
1
Under DBCP
Ophthalmic
Microscope
2 Cryomachine 1
3 Automated Perimeter 1
Dermatology
1 IPL Laser with RF 1
2 Q-Switched Laser 1
3 Ultrasonic Face Lift 1
Model
Name Qty Unit Rate
5
3
1
1
1
1
9
1
Total
Amount

S.N Name of Equipment Mfg Co.
Model
Name
Qty Unit Rate
4 Diode Laser 1
5 Digital Ionotophoresis 1
Pathology
1 Automated
Coagulation Analyzer
Fully Automated three
1 part cell counter (18
para)
2 Binocular Microscope
3 Rotary Shaker
Four Door Vertical
4
Refrigerator
Automated System
For Identification And
5 Antibiotic
Susceptibility Testing
of Micro Organisms
Automated Slide
6
Stainer
Balance Weight
7
Machine
Orthopedic
1
Battery Operated Drill
Machine
1
2
Hohman Variable
retractors
1
3 Bone Punches 1
4 Nerve Locator 1
5
Broken screw removal
set (Hollow will)
Minimally invasive&
mini-open Discectomy
1
6 andfusion system for
both cervical and
thoracolumbar use.
1
7
RF Electrode for Mitek
VAPR System
5
8 Flexible Reamer
Wire Cutter tungsten
1
9 tip with 2mm wire
cutter
1
1
1
1
1
1
1
1
1
Total
Amount

S.N Name of Equipment Mfg Co.
10
11
Sepectrum
Instrument Shoulder
Arthos
Monopolar Cautery
Cords
12
Pencil Drill for Hand
Surgery
1
13 Centrifuge- 1800 rpm 1
14 Bipolar Cautery Cords
High definition
Camera System with
Xenon Light Source, 3
1
15 chip camera, light
cable (thicker &
longer) video imaging
capturing device
1
Physiotherapy
1 Isokinetic System 1
2 Cryotherapy Unit 1
3 Multi CPM Unit 1
4 Microwave Diathermy 1
5 Exercise Bike 1
6 Trapeze 1
7 4 Channel TENS 1
8 Bolsters 1
9 Wobble Board
High Frequency Chest
Wall Oscillations-
1
10 Adult & Pediatric
Positive Expiratory
Pressure- Adult &
1
11 Pediatric
1
12 Therassist G5 1
ENT
1
Operating Microscope
for ENT, Plastic, Neuro
and spine.
Model
Name Qty Unit Rate
1
1
1
Total
Amount

S.N Name of Equipment Mfg Co.
2
3
4
5
Nasal Endoscope
adult 0 degree 4mm
Nasal Endoscope
pediatric 0 degree
2.7mm
Nasal Endoscope
Adult 30 degree 4mm
Nasal Endoscope
Pediatric 30 degree
2.7mm
Laparoscopy & Urology
1 Ureteroscope
Neonatal/Pediatric
2 Resectoscope
CSSD
1 Drying Machine 1
2 Incubator 1
3 ETO 1
4
Auto Control Panel for
Autoclave
2
General
1 Fogging Machine 7
Model
Name Qty Unit Rate
3 Nebulizer 10
4 Fetal Doppler 4
5 Needle Destroyer 20
6 Suction Machine 5
1
1
1
1
1
1
Total
Amount
7 Autoprocessor 1
9
Solar Water Heater
Plant
Please fill in Annexure – 16 and upload on website.
10 Instruments Please fill in Annexure – 17 and upload on website.
Note :
1. The Rates quoted should be inclusive of all taxes.
2. Kindly mention the rates of accessories separately in the financial bids for Future
consideration on letter heads as annexure.

3. The Warranty/Guarantee for one year and free service clause to be clearly
mentioned by the Manufacturer on their letter head. If the Authorized dealer is
going to carry out the service then they have to furnish the authority letter given
by the manufacturer to sale/service the specified product in this Territory.
4. Rates for Annual Maintenance Contract of Medical equipment (both types Labor
& Comprehensive) for seven year should be mentioned separately in the
Financial Bid which will be considered for price evaluation. It should be clearly
mentioned whether AMC /CMC will be done through company itself or its service
franchise/dealers. In that case Manufacturing Company must give authority
letter to such franchise/dealers on their letter head clearly mentioning free
service period and AMC/CMC for period of three years.
Type of
AMC
1 st Year
2 nd Year
3 rd Year
N year
Labor AMC Comprehensive
AMC
Executed by
(manufacturers/authorized
service dealers) Name and
address to be specified here
Medical Superintendent
Signature of Suppliers/Dealers Shri Vinoba Bhave Civil Hospital
With Rubber Stamp Dadra & Nagar Haveli
Silvassa.

Annexure – 1
Department of Medicine
S.N Technical Specifications of Equipment Mfg. Co.
Preferred
1 Temporary Pacemaker
APC/Maquet/
Operating Modes VVI, VOO (over drive :200to350 Medtronic/
ppm)
Biotronic
R-Wave Sensitivity Variable from 1mV to 20mV
(2ms/13 ms triangular test
pulse)
scale accuracy : 1 to 10 mV
±10% 10 to 20 mV ±20%
Input Impedance
Defibrillation
8k ohm ± 10%
Protection Suppression Diode
R-Wave Filter High quality filter for acceptance
of R-Wave specified 22Hz
frequency components
HF-Filter for suppression of high
frequency Interference pulses
Output Pulse Polarity: cathodic, capacitivity
coupled
form: biphasic asymmetric
width :1.5 ms ± 0.03ms
Output Pulse stabilized output variables from
Amplitude 5V to 15V
scale accuracy ±5%
Detection of Output Red LED flashes synchronously
Pulse
Stimulation
to every stimulation pulse
Frequency
Run Away
variable from 30to 180ppm
scale accuracy: 40-100ppm±5%
>100ppm ±10%
Protection 200ppm±15ppm
Refractory Period (0.375*Pulse interval )ms at
nominal setting :313ms±5%
Interference Input pulse sequence
Recognition 4.5 Hz) cause the
system to switch over to the
asynchronous stimulation
frequency

Battery Control Visual Indication
9 Volt 1 no./AA battery (with
backup system while changing
Battery
the batteries)
60mm*115mm*20mm, plastic
Dimension housing
Weight 185g(incl. battery)
Security sockets;1.8 to 2.3 mm
diameter
Connection of Leads
2 12 Channel ECG Machine
• It should have simultaneous 12 channel ECG recording
with 12 lead simultaneous acquisitions.
• It should have minimum 5 inch high resolution foldable
screen.
• QWERTY alphanumeric keyboard
• Built in ECG parameters measurements and
interpretation
• Print Mode: Presample / Real time Sample/Arrhythmia
triggered sample• Capability of storing minimum 100
ECGs
• Should support external archiving i.e. USB drive for
virtually unlimited ECG data storage.
• Built in rechargeable lithium ion battery
• Communication interface: Ethernet, RS 232, USB
• It should have circuit protection from
defibrillator and pacemaker
• It should have sensitivity from 2.5 to 20 AGC (mm/mV)
with CMRR ≥ 100 dB.
• Safety Standard: IECI/CF
• It should have a thermal printer to print A4 size Z fold
or 210 mm roll papers.
• The record speed range from 5 to 50 mm/sec
• Integration with PC with software to store and transmit
the ECG recordings.
Standard Accessories:
1. Patient cable 12 Lead: 1 no.
2. Chest Electrode: 6 nos.
3. Limb Electrode: 4 nos.
4. Jelly Bottle: 1no.
5. Paper Roll: 5 nos.
6. Power Cord: 1 no.
7. User Manual: 1 no.
GE/L&T/BPL/
Alan

3 Cardiac Stress test Machine
1. System should acquire and analyze 12 leads.
2. System should be able should run on Windows operating
system and should be provided with the computer system
with the following configuration: Pentium Core 2Duo or
Dual core CPU with DVD, 19” Color monitor; 160 GB Hard
drive, Mouse, Keyboard and UPS for the CPU.
3. Signal acquisition and digitization from patient should be
performed at the patient itself for elimination of
environmental noise. It should have wireless patient
module between patient and analyzer thus providing
wireless transmission of patients ECG / remote patient
preparation. The wireless module must have display for
ECG waveform, electrode impedance check, low battery/
lead fail display.
4. Should provide standard Full Interpretation of Supine
ECG with reasoning.
5. Should have display of real time 12 lead diagnostic
quality ECG waveform, average complexes beat of all 12
leads with superimposed color comparison along with
digital value of ST level and slope. Display of enlarged
complex and facility of dynamic lead selection for
maximum ST changes. The display of 1mm graph on the
monitor should be similar to the graph on the recording
paper.
6. Automatic detection, display, Storage and review of
arrhythmia, Heart Rate, Double Product and METS. It
should have online HR METs, and ST running trends
available on the screen during exercise.
7. Should have filters for line frequency and special filters
to reduce noise and baseline artifacts without
compromising the ECG frequency response.
8. System should have full disclosure play back, review and
storage of patient ECG raw data for unlimited numbers
depending upon size of the hard disk. The unit should have
the ability to readjust the “J Point” in increments of 1 m
sec and generate a new report from stored raw ECG data.
9. System should provide multiple and customizable
printing formats as per user’s choice on A4 size high
resolution thermal printer for online real time printings. It
should also be possible to print reports on laser printer.
Should be supplied along with the compatible laser printer.
10. System must have ECG trigger output to interface with
external automatic devices.
11. Should be supplied with Heavy Duty Treadmill, with
speed ranging from 0.5 to 12 mph and grade of 0 – 22%
with suitable 3 KVA servo stabilizer. The treadmill should
be US FDA approved OR CE certified.
GE/Allengers/
BPL/ Mortara

12. Should be supplied with Automatic Non-Invasive Blood
Pressure Monitor, which can be programmed to take the
blood pressure automatically with each stage, without any
need to manually take the measurements. The Automatic
NIBP Monitor should be fully compatible with the stress
test system for bi-directional exchange of data. Automatic
NIBP Monitor and the Stress Test System should also have
facility of measuring and recording SpO2 (Pulse Oximetry)
values, automatically with each stage.
13. The Machine should be US FDA approved and CE
marked.
14. Buyback of existing Stress Test Machine of BPL Make
Dynatran which is in working condition.
4 Biphasic Defibrillator with AED pacing
1. The defibrillator should be based on biphasic
waveform technology
2. The machine should have facility for choosing energy
manually from 2 – 360 J in Biphasic Truncated
waveform or up to 200J in Rectilinear Biphasic
waveform and provision of choosing an AED energy
up to minimum 200 j.
3. Charging time should be less than 10s for 200 J
4. Should have facility for manual energy delivery thru
external & internal paddles, synchronized cardioversion
(through hard paddles) and automated
external defibrillation (through pads).
5. Should have built in external pacing facility (both
demand and non demand modes).
6. Should have color LCD/ TFT monitor display for clear
view of the screen from distance.
7. Should work both on 220 VAC and rechargeable built
in battery.
8. It should have LI-ON battery with battery indicator on
the screen
9. Should have a built in recorder minimum 50 mm.
10. Should have optional facility of Masimo Pulse
Oximetery
11. Should be US FDA approved
5 Internal/Implantable Defibrillator
• it should provides single chamber rate adaptive
bradycardia pacing support as well as tachyarrhythmia
detection and therapy with maximum 30 joule energy.
• It should have optional wireless remote home
monitoring facility based on GPRS system
• It should have a facility of ATP where a device delivers
the ATP before charging for fast and stable right
ventricular rates within VF zone
Nihon
Kohden/
Philips/GE/
Mindray
Meditronics
/Biotronics/
St. Jude
Medical/
Boston Sci.

• It should be provided with PRO-MRI ICD Lead with 8F
lead delivery System.
• It should have three zones for programming of
appropriate therapy delivery system.
• It should have service time of more than 7 years with
programming of VVI 60ppm; 2.5V at 0.5 ms; RV 15%
pacing; 700 Ω; quarterly shocks; Home Monitoring and
full HD on.
6 Holter with Ambulatory BP
Power Consumption: 1 aaa alkaline or rechargeable
battery
Dimensions: 66 x 59 x 17 mm
Weight (excl. battery): 50g
Sampling, A/D resolution: 1200Hz or 600Hz, 12 bit
ECG storage: 150, 300 or 600 Hz on a standard MMC/SD
memory card
Storage Capacity: up to 96 hours of ECG (300 Hz, 3
bipolar channels, 1GB memory card)
Frequency Range: 0.05-100 Hz (-3 dB)
Dynamic Range: 16 mVp-v
DC offset tolerance: ±300mV
Input Impedance: 100MOhm
ECG: 1,2,3,5 channels (7 leads)
Data Transfer:
Optical cable with USB plug
Bluetooth
SD/MMC card reader is needed for receiving data
Conformity Certificates: CE
Ambulatory BP
Measurement Method: Oscillometric
Power Consumption:
2AA Rechargeable or alkaline batteries
4AA Rechargeable or alkaline batteries
Dimensions: 98 x 69 x 29 mm & 124 x 82 x 33.5 mm
Weight (excl. batteries) : 190g, 250g
Measurement Range:
Blood Pressure: 30-260 mmHg (4-35 Kpa)
Pulse: 40-200 beat/minute
Passive Accuracy: 3 mmHg or 2% of the measured value
Data Transfer:
Optical cable with USB plug
Wireless Bluetooth
Optical cable with serial/USB plug
Storage Capacity: 600 measurements
Conformity Certificates: CE, FDA
Validation: BHS, AAMI protocol
Vasomedical
/Mortara / GE

Annexure – 2
Department of Pediatrics & Neonatology
S.N Technical Specifications of Equipment Mfg. Co.
Preferred
1 Radiant Heat Warmer with resuscitation unit
• Mobile newborn table with fixed height radiant warmer.
• Antistatic castors, 2 with brakes.
• Table surface with mattress with infant head/ shoulder
support.
• Mattress padding-foam density approximately: 25kg/m 3 Neotech/Bird
Meditech/
Meditrin/
Fanem
.
• Mattress cover: removable with zipper, waterproof,
washable, resistant to cleaning with chlorine based solution
and flame retardant.
• warmer module should easily pivot @ 90 degree in either
direction to facilitate x-ray without affecting thermal
operation
• Side boards transparent acrylic, drop down by single hand
action and lockable.
• Lower shelf & Under table 2 storage drawers, IV Pole and
swivel trays for instrument
• Warmer body fabrication should be in Stainless steel
• Side rails allow for mounting of accessories.
• Hood suspended above the table integrates heating element
and overhead light.
• Overhead light 2 x 50W halogen spot, with dimming function.
• Heating element: Ceramic Heater with parabolic reflector
and protected by metal grid.
• Control unit allows air and skin temperature preset (LED
indicator) and drives radiant heater output (servo & manual).
• Integrated timer: 1-59min, with count-up and count-down
feature.
• Temperature range, skin: 34-38ºC (user pre-settable).
• Monitoring of skin temperature by means of sensor, range:
30-42ºC.
• Heater output & display: 0-100% in increments of 5%.
• It should have automatic pre warm mode that allows long
term controlled warming of mattress
• Four functionally different modes :- Automatic pre warm,
manual, Skin & Air controlled to maintain optimum thermal
environment
• Control unit: audiovisual alarms according to timer and

temperature presets avoiding overheating.
• Displays reports systems errors, heater failure, sensor failure
on LCD.
• Unit should have On Board Calibration Facility with feather
touch keys
• It should have inbuilt optimal resuscitation with safe &
controlled peak inspiratory pressure (PIP) & consistent &
precise PEEP.
• It should be capable to upgrade with infant weighing scale as
well as motorized height adjustment.
• Power requirement: 220V/ 50Hz.
• Power consumption: 800W.
• Device is produced by ISO 13485:2003 certified
manufacturer (certificate to be submitted).
• Infant Warmer should be safety certified according to CE
93/42 / FDA 510k (certificate to be submitted. Manufacturer
should have supplied CE /FDA 510k certified product at least
24 months prior to submission).
• Infant Warmer should be designed & tested as per IEC 601-
1:1998 + A1:1991 + A2:1995, IEC 601-2-21:1994 and IEC
60601-1-2, 2001 (Test certificates from NABL approved
Government laboratory should be submitted).
• Buyback of a. Wall Mounted Radiant Heat Warmer, Meditrin
Make – in Working Condition (5 Nos.), b. Radiant Heat
Warmer, Delta Make – in working condition (1 nos.)
Should be Supplied with:
a) Oxygen Regulator with Hose pipe, place to keep Oxygen
cylinder, Flow meter, Humidifier bottle with tubings
b) Manual Resuscitation Silicon Autoclavable bag with neonate
& infant Mask
c) Inline manometer to monitor pressure of oxygen given by
resuscitation bag
d) Electrically operated suction unit provides safe settable
suction required for neonates
e) Laryngoscopes with blades Malleable stylet
f) ET tubes disposable with slip joints sizes: 2.5, 3.0, 3.5 & 4 mm
2 LED Phototherapy
OVERHEAD SOURCE UNIT (Blue LED)
It should have BLUE LEDs which do not emit light in the
ultraviolet (UV) range - reducing the potential risk of skin
damage
Also it should not emit light in the infrared radiation (IR)
range - reducing the potential risk of fluid loss
It should deliver irradiance > 30 µW/cm2/nm) at distance of
15” from source to patient
Neotech /Bird
Meditech/
Fanem

LEDs should eliminate costly and time-consuming bulb
replacements by providing up to 20,000 hours of use
It should be Totally cool therapy. Should not generate heat
Power consumption should not be more than 40 Watts
It should have stand movable on castors
It should have angle adjustment facility to use with Radiant
Warmer
It should have Digital time totalizer on LCD with backlit
LED Phototherapy should be safety certified according CE
93/42, FDA 510k
Stand fabrication should be in Stainless steel
Phototherapy Should be tested as per IEC 60601-1-2, 2001,
2nd Edition
IEC 601-1:1988 +A1:1991 +A2:1995
IEC 60601-2-50 2000
Luminance : ≥35000 Lux
Color Temperature: 3500-5000 K
Spot Diameter: 150-300 (mm)
Illumination Depth: ≥800 (mm)
Light –adjusting Mode: Eight grade dimmer system
Temperature at Surgeon’s Head: ≤1%
Power Supply: 220 Volts, 50 Hz.
CRI (Ra) : ≥97%
3 Neonatal Ventilator
• Advanced microprocessor based continuous flow , pressure
limited, time cycled ventilator for very low body weight
infants (premature, newborns) upgradeable for additional
functions
• Should be an upgradeable design with software/hardware
upgradeability for new/ future functions with inbuilt graphic
screen
• The ventilator should have ventilation modes as below:
o IPPV / IMV
o Assist Control
o SIMV
o CPAP
o HFOV
o PSV
o VG
• Should have settings for :
Peak Inspiratory Pressure 10 - 80 cmH2O
Flow independent PEEP 0 – 15 cmH2O
Inspiratory Time 0.1 – 2 sec
Expiratory Time 0.2 – 30 sec
Draeger/ GE
/Philips

Maximum Rate (based on Insp. Time and
exp. Time)
200 bpm
Inspiratory flow 1 – 30 lpm
Base flow (VIVE) 1 – 30 lpm
Slope control 0 - 2 sec.
FiO2 21 - 100%
• Should have real time monitoring at Y-piece of:
o Pressure - Peak, Plateau, Mean, CPAP/PEEP
o Expired Tidal Volume (Monitored), Expired Minute
Volume, leakage in %
o Frequency/ Rate - Set (Inspiratory), Spontaneous MV
in %, total , I:E ratio
o FiO2
o Lung Mechanics - Resistance, Compliance , C20/C,
Time constant Tc, RVR
• Should have automatic alarm settings for all alarms. MV
alarm can be manually adjusted along with alarms for :
o Disconnection
o Tube blocked
o Ventilation hose kinked
o High/low Pressure
o High/low Minute Volume
o High Rate
o High Tidal Volume
o Apnoea / apnoea alarm time
o High/low O2 % (automatic settings)
o Oxygen line failure
o Compressed air failure
o Total electronic failure (with error code)
Pressure Support/ Volume Guarantee
• It should be possible to give leakage adapted pressure
support to spontaneously breathing patients with a set
volume guarantee.
• Volume guarantee should be regulated with lowest
possible airway pressure within a set PIP.
Medical Air Compressor
• Dedicated Medical Air Compressor to provide quality air as
per ISO standard
• Snap fit with the ventilator machine
• Peak flow should be minimum 180LPM

• It should be of original company whose ventilator machine
is quoted.
• It should be CE certified.
Nasal CPAP ventilation
• The nasal CPAP unit should be self contained with head
strap, hood, nasal prongs, fixing unit.
• Should be possible to field upgrade the same if required
HFOV
• It should be possible to combine HFOV as below :
o IPPV + HFOV
o CPAP + HFOV.
• The HFOV function should be integrated in same machine
and NOT external facility.
• The HFOV function should control :
o Frequency in Hz : 5 – 20 Hz.
o Amplitude control : 0 – 100%.
• It should be possible to use HFOV WITHOUT disconnecting
the patient by simply switching ON/OFF in the same
machine .If HFOV is offered, separate patient tubings for
same to be offered.
• Should measure parameters in HFOV such as DCO2, VtHF
(tidal volume in HFOV), MVim (MV in IMV strokes in
inspiration), VTim (MV in IMV strokes in expiration)
• Scope of supply should include
o Basic Unit ( 220 - 240 V)
o Modular corrosion free Trolley
o Silicon corrugated Hose set
o High frequency hose set (Autoclavable)
o Servo controlled humidifier with reusable chamber
o Flow sensor – Minimum 10 pcs.
o O2 cell
o Nebuliser
o Oxygen connecting Hose
o Air connecting Hose
o Hinged arm for rail (Support for patient circuit)
o Neonatal test lung
o Instruction Manual
o Medical Air Compressor
• Quality Standards and Support requirements –
o The offered unit should have CE certificate
o The unit also should have FDA certification
o The unit should comply with relevant IEC
Certification
o Indian subsidiary/ dealer should have nationwide

network, support offices and must be also ISO
9001 certified.
4 3 Para Monitor
1. Should be suitable for adult, paediatric neonatal patients
monitoring.
2. Should have minimum 8 channels of waveforms with 15’’
TFT-LCD colour integrated touch screen display (resolution
min 1024*768). Should display 11 waveforms will all ECG
waveforms.
3. Should monitor ECG, Respiration, NIBP, SpO2, Dual
Temperature,Dual & Dual IBP as standard
4. Should have ST analysis, Arrhythmia detection as standard in
every monitor
5. Should have Drug Dose Calculation and OxyCRG as standard
in every monitor
6. Should have pacer spike detection as standard
7. Defib and ESU protection should be present
8. Should have monitoring, surgery and diagnostic mode of
monitoring
9. Arrhythmia monitoring for Asystole, Vfib/Vtac, VT>2,
Couplet, Bigeminy, Trigeminy, R on T, PVC, Tachy, Brady,
Missed Beats, IRR, PNC, Vbrady.
10. Monitor access should be with Touch screen and rotary
knob.
11. Fast access key should be provided for quick function.
12. 120 hrs of trend and 60 events with waveform as standard in
all monitors
13. Color or position of waveforms or parameters should be able
to be adjusted based on users preferences. Big font on
screen format should be present.
14. Nurse call, Analog output, VGA output port should be
standard in every monitor.
15. Monitor should have USB port for software upgrade
16. Anti left lock facility should be possible for better hospital
asset management
17. Should have inbuilt three channel recorder as standard in
every monitor
18. Should have 120 hrs (typically) of battery backup typically as
standard in every monitor
19. Inbuilt three channel recorder as standard with every
monitor as standar
20. Should be CE approved and comply to European Directive
93/42/EEC for both Monitor and software to control
physiologic monitoring systems.
Should have following parameters
Philips/GE/
Draeger

ECG
− Monitor should have capability for display upto 7Lead .
− ST Analysis
− Waveform Freeze option with review of 120 sec
RESPIRATION
− Through impedance pneumography method or EtCO2
SpO2
− Should display digital value and Plethysmograph
NIBP
− By oscillometric principle of measurement.
− Should display Systolic, diastolic, mean pressure in
large easy to read display
Dual Temperature – core and skin
Dual IBP – Should include Starter kit and simultaneous
monitoring of dual temp and dual IBP should be possible
Manufacturer should have ISO 9001, ISO 13485 and ISO 14001
certification
Quoted product should be CE certified.
Scope of supply must include:
− Basic unit with ECG, Resp, SpO2, Dual Temp, NIBP, Dual IBP,
Inbuilt battery, Inbuilt three channel recorder -
− 3 and 5 lead ECG Cable – 1 no each per monitor
− ECG disposable electrodes – 30 nos per monitor
− SpO2 finger sensor and extension cable – 1 no
− Skin temperature probe – 1 no
− Rectal temperature probe – 1 no
− NIBP Hose with Adult & child cuff – 1 no r
− Should be supplied with intermediate IBP cable and
transducer – 1no
− Paper rolls- 4no
− Instruction for Use per monitor
− Manual per monitor
5 Vein Vision Device
• It should be designed specifically for Neonates & Infant
patient.
• It should provide complete solution for finding the artery &
also assist in the diagnosis of pneumothorax.
• It should be micro computer controlled system.
• It should be cool white LED light system so that heat does
not interfere in procedures. The light intensity should be
variable 0 to 100%
• It should be supplied with long fibre optic cable approx. 1
mtr length with optical cable lock facility.
• It should be compact, light & user friendly system mounted
on sturdy trolley from same manufacturer.
Dr Morepen /
Abott/Nice
Neotech

• It should display parameters like % of intensity, usage hours
& timer.
• It should have alarm indications like fan fail, temperature
sensor fail, light source over temperature etc etc.
• The manufacturer should be ISO 9001: 2008, ISO 13485:
3003& CE approved Co only & all necessary documents
should be enclosed in the bid.
6 Electronic Weight Machine
Capacity = 35Kg
Accuracy= +/- 5g
High Bright LED Display
Kg to Lbs Conversion facility
Facility to weigh accurate weight of crying / active baby
Baby Pan size = 22 X 14”
Platform size = 12 X 12”
Detached Platform and Console
Operating Voltages = 200V to 260V A
7 CPAP Machine
• It should be relatively quiet, mobile and sturdy, simple to
operate.
• It should have facilities to provide CPAP from 3-10 cm of H2O
• It should also have facility to deliver Bubbling CPAP.
• It should have facility to deliver manual IPPR.
• It should have inbuilt Air Source.
• It should have inbuilt Blender of Air & Oxygen for 21% - 100%
FiO2 Adjustment
• It should have servo heated wire humidifier for warming gas
delivered to patient.
• Humidifier should have separate LED display for chamber
temperature and proximal end temperature.
• Auto cleavable, transparent, unbreakable Humidifier
chamber.
• It should have Digital and Analog display of delivered
pressure measured at proximal end.
• High and Low CPAP Level settings with alarm.
• Safety pressure relief in event of accidental over pressure.
• Patient Interface System like Head Cap, Nasal Cannula should
be provided.
Zeal/Accord/
SPI
Fisher &
Paykel /
Fanem/ Viasys

Annexure – 3
Department of Ophthalmology
1. Under VBCH
S.N Technical Specifications of Equipment Mfg. Co.
Preferred
1 Nd-Yag Laser
LASER
Lumenis /
Opto/Lynton
Laser Source Q-Swiitched Nd:YAG
Wavelength 1064 nm
Energy 0,5 to 10 mj per pulse in 30 steps
Spot Size

2 Fundus Camera
Max Image Capture Rate: 3 images per second
Capture Sensor: 5.3 Megapixel Sensor
Video Capture: 640 x 480 @17fps
Flash: 10 step LED
Fixation: External fixation lamp
Mount: Slip lamp mount/hand held
Camera Module Dimensions: 4.8” (w) x 6.1” (d) x 9.7” (h)
Camera Module Weight: approx 1 kg
Retina Module Specification:
Working Distance: 43mm
Compensation range: -30 to 30 diopter
Visual Observation: NIR or Visible light via laptop screen
Mydriatic Field of view: 35 degrees
Non-Mydriatic field of view: 30 degrees
Biomedix/
Leica/ Karl
Kaps/ Karl
Zeiss

2. Under DBCP
S.N Technical Specifications of Equipment Mfg. Co.
Preferred
1 Ophthalmic Microscope
Karl Zeiss /Karl
Microscope An integrated 5-step apochromatic Kaps/ Moller
magnification changer motorized focusing
and fiber optic illumination.
Wedel
Magnification 5 step magnification changer with factors
0.4/0.6/1.0/1.6 / 2.5
Focusing Motorized
Objectives F = 200mm /175mm
Binocular Tube 45 o inclined tube f = 170mm with IPD: 55
mm to 75 mm
Illumination Fiber optic illumination with 12V 100W
halogen reflector lamp
Filters UV Filters, blue barrier filter
Retinal Protection Device.
Work flexibly Compact, design for flexible positioning.
Motorized focus enables bi-manual work
High capacity suspension system for
Precise
movement
Camera
Attachments
(Indian Make)
that should be
compatible with
this microscope.
increased functionality with accessories
Smooth positioning through adjustable
resistance
Easy motion in the focusing plane with
optional XY coupling
Camera with video adaptor and beam
splitter (Indian make)
2 Cryo-Machine
Totally non-electric Cryo Console Unit. The absence of electric
connections ensures safe handling. Cryo is functionally designed
to simplify Cataract, Retinal, and Glaucoma procedures by use of
a variety of surgical probes.
Ophthalmic Deluxe Cryo
The Cryo is foot operated and very sleek enabling easy handling
and the pedal control enables instant freezing and defrosting.
The console face includes a pressure indicator and ON-OFF
reading for visual indication of the system.
Special Features
Basco
/Kohden/Leica

Useful for Cataract, Retinal, Glaucoma and Intravitreous.
Foot control provision for easy handling and instant freezing and
defrosting.
Liquid nitrous or Carbon-DI-oxide gases technique is used for
low temperature achievement.
Non-electric.
1.It has got a reverse flow control mechanism and it cleans the
inner line of the gas conveying tube automatically when the foot
is released.
2. It has got a seperate cylinder connector for fixing with the
cylinder, which increases the length of the usages.
3. Gas starts flowing in the probe only when the pedal is
pressed. So the probe is saved with high pressure gas
accumulated in the inner line, results long lasting of the probe
and the gas is released in the console unit and minimising the
noise.
4. Breaken 'O' rings in the inlet and outlet of the probe will not
stop the functioning of the cryo probe as the gas is passed
through the probe only.
5. For camp work the deluxe works properly and the 'O'
rings(washer) will not get pluged, and it can be removed at any
time when needed and any probe can be changed.
6. Cylinder need not be brought near the patient since it has got
a two meter cylinder connector to increase the length.
7. Defrosting will take place without any trouble within two
seconds, because of reverse flow control system.
8. It had got ON-OFF indicator to check whether the gas enters
inside the probe properly or not.
3 Automated Perimeter
Test Capability: Central & peripheral 100° (upto 160° with
fixation shift)
Test Mode: Static
Stimulator Screen: Part Hemispherical radius 300mm.
Integrating diffusing surface
Background Illumination (with auto ambience level
control): 10asb standard perimtery
320 asb for blue on yellow (SWAP)
Stimulus Source: Rear Projection LED
Stimulus Color: Green or Blue
Stimulus Size: Goldman III (0.43°) for standard perimetry
Stimulus Intensity: 0.03 asb – 1000 asb
Stimulus Duration: Adjustable 0.1 – 9.9 sec & adaptive
Patient response Time: Adjustable 0.1-9.9 sec & adaptive
Topcon/Zeiss/
Medmont/
Humphrey/
Appasamy

Inter Stimulus delay: Adjustable 0.1-9.9 sec & adaptive
Pupil measurement: semi automatic
Specialty test Strategies: Flicker Sensitivity
Standard Test Strategies:
• Threshold
• Fast Threshold
• Smart Threshold
• Fast Scan
• Screening
• Neurological
• 2-Zone
• 3-Zone
• Quantify Defect
• Driving
• Binocular Driving
• Binocular Single Vision
• Custom
Fixation Methods: Digital eye tracking with camera view
Heijl-Krakau blind spot method with camera view
Fixation Target: Red LED 650nm
Test lens Diameter: 38mm
Patient Database Backup: CD,DVD,USB with auto procedure
, on External PC
User Interface: External PC, Monitor, keyboard & Mouse
Electrical Requirements:
110-230VAC 50/60Hz
Power Consumption: max 35 W

Annexure – 4
Department of Dermatology
S.N Technical Specifications of Equipment Mfg. Co.
Preferred
Derma India
/Lumenis
/Lynton
1 IPL Laser with RF
IPL Laser with RF
Treatment Handle: 3 Types
Spot Size: 60mm x 15mm & 8mm x 40mm
Spectrum:
HR 610-1200nm
SR 560-1200nm
AC 430-1200nm
PL 530-1200nm
VL 585-1200nm
RF Frequency: 750 ±10% KHz
Energy Density: 20-50j/cm 2
RF Duration: 0.1-3.0s
Discharge Interval: 3-5s
Input Power: 1200w
1 st Pulse: 0.1-10.0 ms
Power Supply: AC 220v 50Hz 10A
Sub Pulse: 0.1-10.0 ms
Cooling: WATer, Air, Semi-conductor cooling
Cooling Temperature: -5°C
Dimension: 650mm x 400mm x 450mm
Net Weight: 25.5 Kgs
2 Q-Switched laser
Laser Type - Q – Switched Nd Yag laser
Wave length - 1064 nm & 532 nm
Frequency - upto 6 Hz
Width of pulse - 20 ns
Energy Density - ≤180 mJ (single pulse); ≤1000mj (direct
pulse)
Spot diameter - 1-6 nm
Electrical requirement - 230 V/50Hz
Cooling system - Internal water-to-air cooled
Dimension (cm) - 24 X 40 X 18
Net Weight - 7 kg
Wattage - 420 W
3 Ultrasonic Face Lift
FEATURES
Microprocessor based on operating system.
S.M.P.S power supply
Derma India /
Lumenis/
Lynton
Derma India/
Krupa
Mediscan

Inbuilt Guard Protection.
Feather Touch Keypad
Three different type pules mode.
Adjustable digital Intensity.
Digital Count Down Timer.
Auto Cut-off Facility with beep sound.
Two types of probe mode available.
Shock proof cabinet.
Highly Powder Coated.
SPECIFICATION:
Power – 220v/240v 50 HZ AC.
Frequency Out Put – 3Mhz.
Power – 0 to 25w Adjustable.
Intensity – 9 Levels
APPLICATIONS
FACE LIFT
BREAST LIFT
EYE CARE
REMOVE WRINKLESS
IMPROVE BODY LINES
IMPROVES NECK & CHEEK LAXITY
4 Diode Laser
Technical Specifications
Light Source - Diode (Continuous, Pulse Wave)
Wavelength - 808 nm
Optical Energy - Up to 50 J/cm 2
Pulse Duration - 350 ms
Repetition/Coverage Rate -1 – 10 Hz/hr (10 Hz), ST (1-10 Hz)
Spot Size - 14 X 5.5 mm
Optical guide - Sapphire Crystal
Cooling - 0 º c
Electrical Requirement - 230 V – 50 Hz
Weight - 30kg
5 Digital Ionotophoresis
Power – A.C. 220/240v 50HZ.
Microprocessor- Power Supply.
Digital Procedure Count down Adjustable Time.
Spike Guard Protection.
Digital Force Display.
Indivisual Gel for Application.
Variable force adjustment.
PROBE
Pencil Probe with steel roller.
Earthing Probe.
Plastic Tray for lonotophoresis (2Psc)
Derma
India/Lumenis
/Lynton
Derma
India/Krupa
Mediscan

Electrode Plates.
APPLICATIONS
Pegmetation
Under Eye Dark Circles.
Oily Skin.
Active Acne.
Face Lifting.
Skin Lighting.
Hyperhidrosis.

Annexure – 5
Department of Pathology & Microbiology
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Automated Coagulation Analyzer
• Machine should be random access, Bench Top fully
automated walk away system.
• Principal should be based on optic clot detection system.
• It should have inbuilt windows based software for
functioning of machine.
• It should have touch screen and additional facility of
external keypad.
• It should strictly work with inbuilt software and no
external computer should be required to avoid computer
break downs.
• Machine should be capable to perform Clotting,
chromogenic and immunologic test.
• It should have 8 measuring channels working
simultaneously for different test protocols.
• Machine should have 5 channels for clot detection, 1
channel for chromogenic and 1 channel for immunologic
test.
• Probe should have liquid level sensor, probe crash sensor,
preheating for reagents.
• Machine should have internal and external washing
facility for probes after each step of reagent/ sample
addition.
• Syringe capacity should be 4 – 400 micro liters with
precision of 1.0 micro liter.
• Machine should have 23 reagent positions.
• On board cooling facility should be available with the
machine.
• Machine should have reagent mixing facility. Machine
should have stirrer for reagent mixing.
• Machine should have 27 sample positions.
• Facility to load primary tubes as well as sample cups
simultaneously should be available.
• Auto dilution facility should be available for samples.
• Auto and manual calibration facility should be available
Abott/Siemens/
Tulip

with the machine.
• It should have dedicated QC parameters like 7 controls,
multirules etc.
• Machine should work on bidirectional mode so that it can
participate in LIS.
• Machine should have inbuilt printer only and it should
print calibration and reaction curve printouts.
• Power supply should be AC 110V/220V, 60Hz/50Hz.
• Machine should be CE/ US FDA approved.
• Company should be ISO 13485 certified.
2 Fully Automated three part cell counter (18 para)
Fully automated Cell counter with 18 parameters and
with 3 differential counters & platelets with histograms
Principles: WBC, RBC and PLT : electrical Resistance detection
HGB: SLS Hemoglobin, dual transducer
HCT: Cumulative Pulse Height Detection
Parameters: 18 Parameters
WBC, RBC, HGB, HCT, MCV, MCH, MCHC, PLT, LYM%, MXD%,
NEUT%, LYM#, MXD#, NEUT#, RDW-SD, PDW MPV, P-LCR
Automatic Sample probe cleaning function
Automatic liquid circuit cleaning fast
Working Mode: 24 hrs running continous, auto sleeping &
wake up
Throughput: Approx. 60 Samples / Hour
Sample Volume: Whole Blood mode - 10µl, 20µl,
Precision: Parameter Whole Blood Mode
WBC 3.5%or lower
RBC 2.0%or lower
HGB 1.5%or lower
HCT 2.0%or lower
PLT 6.0%or lower
Linearity:
WBC 1.0-99.99x10 3 /µl (within ± 0.3x10 3 /µl or ± 3%)
RBC 0.30-7.00x10 6 /µl (within ± 0.3x10 6 /µl or ± 3%)
HGB 0.1-25.0g/dl (within ± 0.2 g/dl or ± 2%)
HCT 10.00-60.0% HCT% (within ± 1.0 HCT% or ± 3%)
PLT 10-999x10 3 /µl (within ± 10x10 3 /µl or ± 5%)
(When RBC < 7.00x10 6 /µl)
Data Storage: 240 patient results
Touch screen back lighting LCD
Interfaces: 1 parallel interface, 2 usb interface 2ps/2
interface, 2 rs232 interface (with net)
Built-in thermal Printer: 5x7 dots, 21 characters per line (128
dots/line)
Abott/Siemens/
Tulip

Dimensions: Approx. 420x480x355
W x H x D (mm)
Weight (Kg): 28
Power Consumption: 230 VA or less
3 Binocular Microscope
Fully imported Microscope with Siedentopf tube with 30’
viewing angle in upper & lower position , tube can be
rotated 360”
Colour Corrected Infinity Optics with Plan Achromat 4x/0.12,
10x/0.25, 40x/0.65, 100x/1.25 Oil Objectives
Modular illumination with 30 watt Halogen light.
Blue light intensity display on both sides of the stand.
Fixed Koehler illumination with Abbe condenser 0.91/1.25
Up gradable for Dark field, 40x Phase and contrast
techniques.
Quadruple 4x nosepiece pointing towards back.
WF10x/18mm focusable eyepiece –1 NO. for binocular
Microscope
Precise & sensitive coaxial fine focusing control with special
gear of 0.3 mm/rotation. Coarse drive 4mm/ rotation
Magnification up to 1000x.
Standard set complete with built-in 6V20W halogen light
illuminator, quadruple ball bearing nosepiece, focusing by Coaxil
coarse and fine focusing controls, high resolution long
barrel achromatic objectives 4x, 10x, 40x (Spring) and 100x
(Spring, Oil Imm.), with an inclined binocular observation
tube ratable through 360 degree fitted with fungus resistant,
anti-reflaction coated prism, compensating widefield
eyepiece WF10x (F.N. 18) and with right hand co-axil low
drive mechanical stage, substage Abbe condenser 1.25 N.A.
with iris diaphragm focusable with rack & pinion
4 Rotary Shaker With 0 -15 minutes timer & speed
regulator
5 Four Door Vertical Refrigerator (Deep Freezer)
Temperature range: -18 degree C to +6 degree C
(adjustable with digital indicator cum thermostat)
Insulation: 2” injected puff
No of Doors: four insulated doors with gasket, lock & key
with spring loaded hinges
Construction: outer body/tank and doors are fabricated
with S S Sheets of 20/22 swg.
No of Shelves: three adjustable (wire mesh of S S 304
quality)
Condensing Unit: fitted on top with suitable kirloskar
Nikon/Olympus/
Zeiss
Remi/Standard
Company
Bluestar/Voltas/
Standard Company

Copeland/tecums compressor, condenser, fan motor,
dryer.
Electrical: operates on I phase, 230 volts, 50 Hz of
electric supply
6 Fully Automated System for Identification & Antibiotic
Susceptibility testing of micro-organisms
• Requirement for the fully automated system for
Identification and Antibiotic Susceptibility testing of micro
organisms for both Bacteria and Yeast.
• System should be totally automated for sample
standardization, panel inoculation and loading, incubation
and reading with minimum number of manual steps.
• System should be capable of processing atleast 30 cards
at a time.
• Along with Bacteria and Yeast system should be capable
of identification of Anaerobes, corynebacterium and
fastidious organisms like Neisseria and Hemophilus and
HACEK group of organisms.
• System should have separate panels for Identification and
antibiotic susceptibility testing thus making it more cost
effective.
• System should use reliable and world renown technology
for identification like colorimetry
• System should provide MIC values for drugs and the
analysis of the Antibiotic susceptibility testing results
should be done based on the CLSI guidelines.
• System should be able to perform the phenotypic analysis
to give a complete detail on resistant phenotypes of the
microorganisms based on the MIC values.
• System should make use of panels with barcodes and
should have internal barcode scanning facility to facilitate
the ease of data entry and data management
• System should have the LIS facility thus enabling the bidirectional
data transfer.
• System should have the facility to transfer the data
directly into excel sheet for further analysis.
• System should allow the use of USB drivers or DVD for
data backup
• System should make use of closed or sealed
panels/strips/cards to ensure high level of security for
Siemens/
Biomerieux/BD

oth test and users.
• Panels used in the system should be sufficed with all the
necessary reagents required for the analysis. Thus there
should not be any need to use additional reagents other
than those present in the panel.
• System should be capable of providing rapid results i.e.
within 2-10 hours for routine bacteria such as GNB and
GPC
7 Automated Slide Stainer
A Multi-disciplinary Slide bi-linear batch stainer offering low
cost access to automated staining.
Easy to operate via hand held LCD controller
10 program memory for rapid selection of desired protocol
Should have full range of accessories including: Drying
machine, fume hood, water baths and plumbing kit that can
be added to a standard 10 bath unit.
It should be portable
Power Supply: 12V
Applications:
1. Cytology
2. Haematology
3. Microbiology
4. Histopathology
Capacity: 38 mL/ 10 bath
Standard Scope of Supply along with machine
1. Drying module
2. Fume hood
3. External Bath with lid
4. Add. Rack of 5 slide cap
5. Add.Dish/Bath
6. Tap
7. Plumbing kit
Biomerieux/
Siemens
8 Balance Weight Machine Metlar
Tolado/Biomerieux

Annexure – 6
Department of Orthopedic
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Battery Operated Drill Machine
Drill/Reamer Handpiece. 1
Battery operated, Drill speed 750 RPM. Tourque 50
In. lbs. Reaming speed 250 RPM. Tourque 150 In. lbs.
With 4.9mm Cannulation , With Facility For Pulse
Lavage Attachment, should be Single Trigger operated
with reverser and forward facility by the single trigger
Oscillating Saw Handpiece 1
Battery Operated, Saw Speed 15,000CPM Arc 4º. with
8 Position rotating head. Saw Blade should be fittend
in with pull up and down position ( vertical)
Saw Blades 10
Universal Battery Charger 1
UL2601-1 Complete battery charger with four charging
bays
Battery 8
14.4 Volt Nickel Metal Hybride (NiMH) rechargeable,
Autoclavable Battery,
Connections For the above Handpiece
All the connecting accessories should be attach by
Pulling Mechanism for easy coupling
(1) Jacobs Coupler for Drilling, with 750 RPM Speed 2
(2) A.O.Synthes Coupler, with 750 RPM Speed 2
(3) Synthes Reamer Coupler, with 250 RPM Speed 2
(4) Wire and Pin Driver Coupler, with 750 RPM Speed,
should accept wires and pins from 1.6mm to 2.8mm
2
Microaire/Stryker/
Synthes
(5) SS Case 2
2 Hohman Variable Retractors Kalellkar/
Synthes/Teknomedi
cal/Shushrut/ Inor
3 Bone Punches Kalellkar/
Synthes/Teknomedi
cal/Shushrut/ Inor
4 Peripheral Nerve Locator
Kalellkar/
1. Constant current
Synthes/Teknomedi
2. Microprocessor based.
3. LED display.
4. Current range – 0 to 99 mA, variable in steps at 5mA.
5. Pulse width – 200 microseconds.
6. Availability of single twitch, train of four, tetanus (50Hz),
cal/Shushrut/ Inor

double burs stimulation 3:3, post titanic count modes of
stimulation
7. Single twitch every 1 seconds option.
8. Single twitch every 10 seconds option.
9. Train of four every 10 seconds option.
10. 9 volt battery operated.
5 Broken Screw removal set (Hollow will)
Graphic case for instruments (empty) 1
Assembly pin 1
Assembly forceps 1
Connecting end to hollow reamer 02.00002.015 1
Connecting end to hollow reamer 02.00002.020 1
Connecting end to hollow reamer 02.00002.027 1
Connecting end to hollow reamer 02.00002.035 1
Connecting end to hollow reamer 02.00002.045 1
Connecting end to hollow reamer 02.00002.065 1
Connection end with cent. Pin for 02.00002.015 1
Connection end with cent. Pin for 02.00002.020 1
Connection end with cent. Pin for 02.00002.027 1
Connection end with cent. Pin for 02.00002.035 1
Connection end with cent. Pin for 02.00002.045 1
Connection end with cent. Pin for 02.00002.065 1
Hollow reamer for screws 1.5mm 1
Hollow reamer for screws 2.0mm 1
Hollow reamer for screws 2.7mm 1
Hollow reamer for screws 3.5+4.0mm 1
Hollow reamer for screws 4.5mm 1
Hollow reamer for screws 6.5+7mm 1
Extraction bolt for screws 1.5 mm 1
Extraction bolt for screws 2.0 mm 1
Extraction bolt for screws 2.5 mm 1
Extraction bolt for screws 3.5 + 4 mm 1
Extraction bolt for screws 4.5 mm 1
Extraction bolt for screws 6.5 + 7 mm 1
Conical extraction screw for screws 1.5+2.0 mm 1
Conical extraction screw for screws 2.7 + 3.5 + 4.0 mm 1
Conical extraction screw for screws 4.5 + 6.5 + 7.0 mm 1
Holding forceps 1
Straight hollow gouge, straight left 1
Mallet 200g 1
Universal chuck cannulated with T-handle 1
T-handle with quick coupling 1
Sharp hook, L. 150 mm 1
Synthes /Zimmer

6 Minimally invasive& mini-open Discectomy and
fusion system for both cervical and
thoracolumbar use.
Minimally Invasive discectomy& fusion system of
Herniated Nucleoluspulpous and bony decompression of
the root.
System should to allow PLIF, TLIF,Laminectomy,and
Facectotomy, Ligament Flavum removal, Nerve root
retraction and discectomy.
System should have capability to multi-Level posterior
fusion allowing pedicle to pedicle access at least40mm
for fusion.
System should be adaptable to camera, Microscope
and Loop.
The following components should be integral part of
system.
1. Introducing instruments :-
System should have sequential dilators and outer
sheath for endoscope to avoid cutting of muscles and
hence providing Muscle Sparing Approach to Spinal
Surgery.
2. Flexible Arm Assembly :
Flexible arm with rod connection to secure the
introducing system to OT table should be adjustable in
multi direction.
Should have black bayoneted instruments for universal
applications with Endoscope/microscope/ loop.
The following items should be manufactured by firms
of international repute and should have US FDA
approval.
Micro Endoscopic Discectomy and fusion
System
Guide wire
Flexible Arm Assembly 1
Dilator Diameter
1 each
5.3mm,9.4mm,12.8mm,14.6mm,16.8mm,
18.8mm and 20.8mm, 22.8mm, 24.8mm
Bed Rail attachment 1
1
Meditronic/Teknom
edical/SMPL/Inor

7
Expandable retractor 25 x 60, 70mm 2 each
Openers for above 1 each
RF Electrode for Mitek VAPR System
90° Electrode with Suction Hole – Model S90 – 2 nos.
50° Electrode with Suction Hole – Model S50 – 2nos.
90° Hook Electrode -1 no.
Depuy Mitek
8 Flexible Reamer
Fixed Head Reamer Shaft with Synthes type reaming coupler-
Dia. 6 mm to 15 mm with difference of 0.5 mm
Manman
9 Wire Cutter tungsten tip with 3 mm wire cutter length 9”, Synthes/Zimmer/
double action with straight jaw
Inor
10 Specectrum Shoulder Arthoscopy
Codman/Depuy
CordCutter *EA 1 Mitek/Kallelkar
Arthro Knot Manip Full *EA 1
Arthro Calibrated Probe*EA 1
Arthro Rasp 20 UpBend *EA 1
Arthro TissLib Blade Up*EA 1
Expressew III Flexible Suture Passer 12
Expressew III Flexible Suture Passer Needles 15
Clever Hook, right 1
Clever Hook, left 1
Sixter, right 1
Sixter, left 1
Suture Manipulator 1
Switching Stick, 4mm 1
SS Box for Above 1
11 Reusable Monopolar Cautery Cords Galtron/Standard
Company
12 Pencil Drill for Hand Surgery
Manman/
Pen Type Drill Handpiece
Is should designed for general purpose.
Medtronic/ Codman
It should be useful for superficial use in Foot, Hand and Paediatric Surgery
Simple holding mechanism
Bottle shape
Comfortable grip
Light weight – 300 gms.
Powerful micro motor inside.
Autoclavable with special connector
Should Hold 1,1.5,2mm Drill Bit / Bur
Mini Sagittal Saw Handpiece
Bottle shape
Comfortable grip

Light weight – 300 gms.
Powerful micro motor inside.
Autoclavable with special connector
Saw Blade
5 Different Shapes from 0.3mm to 0.5mm thickness 10
Power Consol 1
Knob for Linear Speed Control Starting from 0-25000 cpm
Toggle switch for selecting Saw & Drill.
Slide Switch for cw / ccw
Indicator for status of Foot Control
Mains on / off switch
Sockets for drill, Foot Control & saw
Socket for AC power supply 220 V / 5 A
Accessories
Supply Cord 1
Autoclavable
Smooth touch
Length 3 mtr.
Push pull connectors
Feather weight
Foor Control 1
On / Off switch
2.5mtr. long cord
Not to be autoclaved
Power supply cord 1
Bur of Different Sizes 10
Drill bits of Different size from 1, 1.5, 2, 25mm 10
13 Centrifuge – 1800 rpm Remi /Standard
Company
14 Reusable bipolar cautery cords Galtron/ Standard
15 High definition Camera System with Xenon Light Source, 3
chip camera, light cable (thicker and longer), video imaging
capturing device
• HD 3CCD CAMERA
1. It should have Max. Resolution 1920 x 1080 Pixel, in
DVI format.
2. Progressive Scan CCD should be - 1/3" x 3
3. Aspect Ratio should be 16:9
4. Sensitivity should not be more than 1.5 Lux. to get
optimum color resolution with all kind of light source.
5. It should have 3 Programmable buttons on head.
6. It should have Freeze Function through button on
Company
Karl Storz/ Richard
Wolf/Maxer/Stryker

head .
7. There should be a facility of Digital Zoom and Optical
zoom also.
8. It should have Facility to invert or flip the image for
allowing surgeon to operate from opposite side of
camera.
9. There should be a function of multi step digital
enhancer.
10. Facility to select different light sources such as LED,
Xenon, Halogen for optimum colors on all.
11. It should have detachable C-mount for use of different
couplers .
12. Video Outputs - HD-SDI -2, Y/C - 2, Composite -2, DVI
-1 , RGB -1
13. Key Board Connectivity for data input.
14. Specialist wise Surgery Selection for optimum setting
for different surgeries.
15. It should also have function of Window, Gain & Antimoire
filter.
16. It should be certified with EN60601-1 , EN60601-2-
18 & CE according to MDD93/42/EEC.
� FULL HD LCD MEDICAL GRADE MONITOR
1. Size of the monitor should not less than 21”.
2. Monitor should have full HD, 1920 x 1200 resolution.
3. It should accepts High Definition signal of 1920x1200
through DVI-D & HD-SDI
4. It should have digital DVI-D input.
5. It should also have other inputs like HD-SDI, RGBS,
composite, s-video etc.
6. All other on screen menu adjustments like gamma,
color, contrast, brightness etc should be provided.
7. Viewing angle should be 180°.
8. It should be provided with Table stand.
9. It should be certified with CE .
• LIGHT SOURCE XENON - 300W
1. It should have integrated 300W xenon bulb .
2. It should have manual or electronic iris to adjust light
intensity.
3. Preferable the lamp hour meter should be on the
front panel of light source.
4. It should have universal Turret to except various make

fiber optic cables.
5. There should be easy replacement of xenon lamp.
6. It should provide with compatible Fiber Optic Light
cable .
7. It should be certified with ISO 13485 & CE - 93/42/EEC
HD VIDEO RECORDING SYSTEM.
1) The system should be a medical grade panel PC with
High Definition video capture card.
2) The system should be configured with Microsoft
Windows 7 operating system , 500 GB hard disk , Intel
Core 2 Duo processor, DVD R/W optical drive, 22”TFT
touch screen display.
3) The system should capable to capture and compress
video signals up to a resolutions of 1080p in real time.
4) The system should be suitable for digital video signals
SDI , HDMI , DVI and analog video signals
COMPONENT , S-VIDEO & COMPOSITE.
5) There should be integrated software for electronic
management of medical records.
6) System should able to stream video & audio signals
from the OT to any computer on the local network.
Endoscopy Trolley :-
There should be 5 shelves , & locker at bottom , sturdy ,at
least one plug should be 15amp,& monitor fixing facility on
top.
Voltage stabilizer – Servo 2KVA , Tolarance ± 1% , ------ 1No.

Annexure – 7
Department of Physiotherapy
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Comprehensive Rehabilitation System
Biotech/BTE
The Rehabilitation Equipment should be a computer-controlled Technologies/
Machine that can simulate functional tasks for the purpose Contrex
of
assessment and training, and allow for isolated muscle and joint
testing and training for upper and lower extremities.
Equipment should be supplied with minimum following
attachments to cover, Rehabilitation , Work simulation and
Sports testing and training :
� Key
� Ball knob: with more than 1.5 inch diameters
� Flat knobs: with minimum two sizes
� Screwdrivers: large and medium sized
� Large and small adjustable lever with interchangeable
handle
� Fixed axis linear motion attachment
� Grip tool
� Pinch tool
� Steering wheel
� Multiple handle crossbar/Ladder climb attachment
� Cable system to allow linear motion (such as
lifting)and 3 dimensional movement (such as PNF
patterns and work task simulations)
� Tool adapter to use standard wrenches & screwdrivers
as exercise tools.
� Calibration Kit
� Swing Tool which can Simulate swings for various
sports activities including Trunk Rotation , Lumbar
Stabilization, Elbow Extension, Forearm
Pronation/Supination
� Cricket Attachment which can Simulate Cricket ball
throw, PNF Diagonal Patterns, Triceps Extension,
Scapular Retraction/ Adduction
� Padded Wrist Straps
� Waist Belt Strap
� Thigh Cinch Strap
� Padded Harness
� Ankle Cinch Strap
Equipment should have following minimum Exercise
types & modes

• Isometric
• Isokinetic: concentric/eccentric,
concentric/concentric concentric/off
• Isotonic: concentric/eccentric,
concentric/concentric concentric/off
• CPM
Actuator / Dynamometer height should have adjustable
height range from approx 20 to 82 inches above floor.
Equipment should have facility to be also used by
wheelchair patients
Actuator / Dynamometer rotation position should be
adjustable full 360-degree rotation
Equipment should be supplied with detachable Patient chair
/ Bench
Equipment should be supplied with suitable cart ( Trolley) ,
Computer and software with following minimum features :
� Monitor with Touch screen interface software
� Lift testing protocol
� Standardized strength protocol
� Isokinetic force curves
� Motor control training feedback in CPM
� Anatomy Software
Immediate comparisons of results at the end of each
exercise
2 Cryotherapy Unit
• Unit should provide cold air up to -32° C.
• Unit should use normal air as princple energy source,
no consumable required to run machine
• It should have air capacity up to 1500 l/min
• System should supply with one tube, one slotted
nozzle and 5mm,10mm and 15 mm size nozzle
attachments.
• Safety class 1 Type B
• Unit should have castores for easy mobility.
• Should work on 230VAC.
3 Multi CPM Unit
All CPM should work separately and simultaneously.
Knee CPM
• Unit should be able to work on adult and pediatric
• Unit should have facility automatically increasing the
programmed flexion angle by 1° every hour up to 5 ° per
24 hour period of time
• Unit should have facility to work more in working ROM
Biotech/Zimmer/
Physiomed
DJO Global /
Ormed

mimicking oscillation with hand.
• Unit should Accelerates quicker through the non-working
ROM
• Unit should have facility when the patient’s threshold for
pain is reached, allows the unit to continue working the
affected limb but at a reduced flexion angle limit.
• Force Reversal: Safety allowing the therapist to set an
amount of passive force without causing damage to the
surgery or unnecessary pain.
Should have following Specification:
• extension (-10°) to (120°)
• Speed Range : 35 degree min to 150 degree min
• Overall Length 37".
• High-quality, easy to attach patient kit
• Carriage width : 28cm (11 in.)
• Power : -230VAC-50/60Hz,
Safety Class : Class I, Type B
Safety Tests : CE0413, UL 2601-1 CAN/CSA 601.1
IEC/EN 601.1, IEC/EN 60601-1-1
Shoulder CPM
• The Shoulder CPM should have following features:
• Hand-held pendant
• Storage card for storing programmed values.
• universal left/right design for both arm activity.
• Anatomically correct adjustment
• Motor Control: on/off
• Reverse-on-load – unit should switch to the opposite
direction when patient resistance increase the target set
value.
• Patient compliance meter should calculates the
cumulative patient use time
• Warm-up mode – the unit should recognizes the start and
stop angles and midpoint. From that point, motion should
initiated 3 degrees from all angles until full ROM is
achieved.
• Pauses: 0-20 seconds
• Speed: 0-100%
• Timer: 0-250 minutes
The Shoulder CPM should allows the following motions of the
shoulder joint:
Adduction/Abduction 0°- 30° - 175°
Internal/External Rotation 90°- 0° - 90°
Elevation (Flexion) with 60° - 90° flexion of the elbow 30° -
175°
Ante/Retroversion (horizontal adduction/abduction) set

manually 0° - 125°
Mains Power: 230V, 50/60 Hz,
Elbow CPM
• It should have facility of Timer in minutes or hours or
continuous operation
• It should have 0 – 59 seconds pause time
• It should have Speed range 1 % to 100 %
• Reverse on load in steps (motor A and B separately)1 – 25
/ patient safety feature
• It should have facility of plantar flexion/extension or
pronation/supination
• It should have Plantar extension/flexion -5° / 0° / 140°
• It should have pronation/supination 90° / 0° / 90°
• It should have facility for gradual and smooth increase of
the range of motion
• It should have higher rate of motion in EROM
• It should display graphic presentation of the overall
treatment cycle
• It should have warm-up protocol for gradual progression
to the maximum range of motion
• It should separate exercising in both directions
• It should have Patient chip card storage facility for store
patient-specific therapy parameters
• It should have less than 30kgs Weight
• It should supply with dedicated fix chair for CPM
4 Microwave Diathermy
• It should have Easy touch button control.
• It should have Adjustable arm
• It should have Overheating (80ºC) is prevented with
magnetron protective circuit.
• System Operation start only at zero intensity.
• System should supply with circular irradiator.
• It should have facility to give treatment to any part of
body by set direction and angle of arm
Technical Specification:
• Power : AC 220V, 50Hz
• Output Power : 0 – 240W
• Output Frequency : 2450Mhz
• Wavelength : 124.4 nm
• Output modes : (1) Continuous (2) Intermittent
• Timer : 5 to 30 Minute
5 Exercise Bike
System should have facility of integrated chip card system so
that all parameter should set according patient condition.
Biotech/
Physiomed
Proxomed/Scifit

• Clear access for easy positioning for training
• It should have Horizontal seat adjustment according patient
height.
• It should have Transport rollers for moving facility.
• Maximum patient weight capacity should be 190kg.
• Accuracy 5% to 400 W, from 400 W 10%
• It should have Induction brake system
• It should have Speed range from 25-115 rpm
• It should have Power range 20-500 W
• Power should Increment in 5 W steps
• It should have following Training Programs
1. Quick start,
2. pulse-based programs,
3. constant watt programs,
4. Isokinetic,
5. hill training
• It should have facility of POLAR pulse measurement single
channel ECG accuracy
• It should have facility of Adjustable pedals
6 Trapeze
Mounts easily to most metal frame headboards (use the
Trapeze Base, below, for nonmetal headboards) and is
constructed from chromeplated, heavy gauge two-piece
square steel tubing for maximum support. Easy to install
without tools (mounting brackets included).Easy to adjust for
height, length, and horizontal position. Can hold up to 250
lbs.
7 4 Channel TENS
Features :-
� should have Micro controller based platform for optimum
accuracy
� Should have Back Light LCD Display for clear viewing.
� Should have Various Modes like Continuous, Burst, Pulse
Width & Frequency Modulation.
� Should have 4 channel to cover more patient at a time
with different Intensity control.
� ABS Shock Proof cabinet.
� Portable & Light Weight.
Specification:-
Biotech/Alay/ Dev
rehab
Biotech/Alay
Medins/ Dev
Rehab/ Bionics

OUTPUT CHANNELS : 4
MODE : a) Continuous : Variable Frequency from 4 to
150 Hz
b) Burst – Variable from 0.5 to 4 Sec
c) FM – It automatically generates impulses from 4
to 150 Hz
d) PWM – It automatically generates impulses of
variable pulse width from 30 to 250 micro second
INTENSITY: Adjustable from Zero to 120 volts for each
channel.
DISPLAY : Back Light LCD Display.
WAVE SHAPE : Biphasic
MAINS SUPPLY : 230 V A.C.
8 Bolsters
• It should make from good quality forms without any
sharp corner.
• It should have three different size
1. Small
2. Medium
3. Large
9 Wobble Board
• It should have aggressive anti-slip base design with a
sensory stimulation surface to offer a new performance
level to balance training.
• It should have rounded bottom that moves in all
directions.
• It should made from lightweight molded plastic.
10 High Frequency Chest Wall Oscillations – Adult &
Pediatric
A system to remove excess mucus from lungs.
Should have full coverage pulsation
Should have a garment system and pump system to generate
high frequency pulsation
Unit should be programmable to suit individual patient needs
System should be supplied with three different size garments
to cover patients from pediatric to adults.
11 Positive Expiratory Pressure Measurement System- Adult
& Pediatric
• System should measure combined, mouth and nasal
pressure measurements
• System should have digital display of the results
• It should small, portable and lightweight
Biotech/Alay
Medins/ Dev
Rehab
Theraband/ Alay
Medins/ Dev rehab
Biotech/
Electromed/
Respironics/
Philips
Biotech/Micro

• System should used latest piezo resistive pressure
sensing technology
• System should battery operated
Technical Specifications
• System should Measure Maximum Expiratory
Pressure (MEP),Maximum Inspiratory Pressure (MIP)
and Sniff Nasal Inspiratory Pressure (SNIP)
• System should have operating pressure +/-300 cmH20
(+/-5PSID)
• System should have burst pressure +/-700 cmH2O (+/-
20PSID)
• System should have resolution 1 cmH2O
• System should have Accuracy +/-3%
• Power Supply Single 9 volt battery
12 Heavy Duty percussion System
• System should provide percussion, oscillation and
vibration.
• It should use for physical therapy, respiratory therapy
and sports medicine application.
• It should provide directional stroking action combines
both Horizontal and Vertical Forces is must.
• Variable frequency controls 10 to 60 cycles per second
• It should have facility of dial controls with visual
display of CPS, time and pulsation range.
• It should have high quality 1/17 horse power motor
• Should have the international safety standard like CE.
• It should supply with following different applicators
1. Percussion adaptor
2. Small sponge adaptor
3. Large sponge adaptor
4. Round firm adaptor
5. Curved sponge adaptor
• It should supply with rolling caster stand and
accessory tray.
• It should operated on 230Volts/50 Hz
• Standard Scope of supply is included.
Biotech/G5

Annexure – 8
Department of ENT
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Operating Microscope for ENT, Plastic, Neuro and
Spine
Apochromatic Optics:
Motorized focus, working distance 200-500mm
Motorized zoom; 1:6 zoom ratio
10x magnetic widefield eyepiece with integrated
eyecups
12.5x magnetic widefield with integrated eyecups
Illumination:
180W Xenon light source
Automatic Iris Control for adjusting the illumination to
the field of view
Display of remaining lamp life time
System Setup:
Manual Balance with guidance via user interface
General Video: Integrated 17” digital display
Connectivity/data Management:
Video-in for external SD video sources
Can be integrated with external 3 chip CCD camera
System Operation:
Multifunctional programmable handgrips
Magnetic clutches for all system axes
Central user interface
Overhead display for showing important system
parameters
Standard Scope of Supply will include:
1. Microscope with support arm
2. Electrical components
3. Xenon Illumination
4. Dust Cover
5. Light guide 2.5m with 90° connector
6. Floor stand with fixed column
7. Tiltable binocular tube f=170mm, 180 degrees
8. Widefield pushin eyepiece 10x
9. Pack of 5 sterile drapes, type 71
10. Pack of 20 sterile drapes, type 88
11. Coupling for microscope
Karl Zeiss/Karl
Kaps/Olympus

12. Pack of 6 asespsis caps for PD adjustment of
180° tube
13. Pack of 6 asespsis caps 27mm
14. Pack of 6 asespsis caps 12 mm
15. Pack of 6 asespsis caps 22 mm
2 Nasal endoscope Adult 0 degree 4 mm
• Should have Wide angled field of vision.
• Should have 3 types of adaptors for fiber optic
cable.
• Should have working length of 175 mm
• Should be Autoclavable.
3 Nasal Endoscope Pediatric 0 degree 2.7 mm
• Should have Wide angled field of vision.
• Should have 3 types of adaptors for fiber optic
cable.
• Should have working length of 50 mm
• Should be Autoclavable.
4 Nasal Endoscope Adult 30 degree 4 mm
• Should have Wide angled field of vision.
• Should have 3 types of adaptors for fiber optic
cable.
• Should have working length of 175 mm
• Should be Autoclavable.
5 Nasal Endoscope Pediatric 30 degree 2.7mm
• Should have Wide angled field of vision.
• Should have 3 types of adaptors for fiber optic
cable.
• Should have working length of 50 mm
• Should be Autoclavable.
Olympus/Richard
Wolf/Karl
Storz/Maxer/Fujinon
Olympus/Richard
Wolf/Karl
Storz/Maxer/Fujinon
Olympus/Richard
Wolf/Karl
Storz/Maxer/Fujinon
Olympus/Richard
Wolf/Karl
Storz/Maxer/Fujinon

Annexure – 9
Department of Laparoscopy & Urology
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Ureteroscope
Fiber-Uretero-Reno scope, compact 7.5 / 9,8 Fr.
Oval irrigation and instrument channel: for accessory
instruments of max 5 Fr.
Angle of view : 12° with offset eyepiece
Distal tip of sheath: 8 Fr. WL 425 mm
2 Neonatal/Pediatric Resectoscope
PANOVIEW-Telescope PANOVIEW-Telescope,
diameter 2,7 mm angle of view 0°, working length
185 mm with Universal-eyepiece, autoclavable
2. Sheath 12 Fr. with Obturator Cysto- Urethroscope
for telescope 2,7 mm, for small children
3. Grasping Forcep flexible Flexible grasping forceps
with overload protection for Cysto-Urethroscope, 4
Fr., WL 230 mm
4. Sheath 11,5 Fr. with Obturator for Resectoscope
with telescope for small children
5. Attachment without instrument port for
Resectoscope with telescope for small children
6. Working element passive cutting action for
Resectoscope with telescope for small children
7. Cutting electrode
8. Coagulating electrode
9. HF Monopolar connecting cable
Olympus/Fujinon/ Karl
Storz/Richard Wolf
Olympus/Fujinon/ Karl
Storz/Richard Wolf

Annexure – 10
Department of CSSD
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Drying Machine
Physical characteristics
1. Manufactured in stainless steel AISI 304
2. Temperature control password protected
3. Temperature setting from 1 up to 99 min, or continuous
4. 16 luer lock air connection for laparoscopic instruments,
Optional
5. 8 shelves capacity
6. Glass door
7. Lockable door
8. Doors can be configured right or left opening
9. Single and double door (pass-through) versions
10. Indirect UV air treatment during the whole cycle Optional
Drying characteristics and control
1. One drying circuits double speed for cabinet
2. Flashing air flow visual alarm indicators if either drying
circuit fails
3. Air flow alarm with re-settable audible alarm, (flashing
alarm indication remains until the air flow is restored)
4. HEPA filtration on drying circuit
5. Pressure sensors for monitoring HEPA filter replacement
6. Indicator on panel advising when HEPA filter replacement
is required
7. Drying temperature settable from ambient to 90ºC
(password protected)
8. Temperature alarms is disabled when door is open, and
for time required to re-equilibrate temperatures in cabinet
after door is closed.
9. Visual indicator to indicate when door is open.
Optional
1. 16 luer lock air connections
2. UV air treatment
TECHNICAL INFORMATION
DIMENSIONS
- Width………approx 710 mm
- Depth …… approx 790 mm
- Height ……approx 1930 mm
- Net weight………approx 190 kg
Tuttaneur / Steridium/
Steelco/ Taxus

CONNECTIONS
- Electric connection…………… 230V/50Hz
Power……………… 2200 W
- Max room temperature admitted……… + 5°C ÷ +40°C
Should carry ISO 13485:2003, ISO 9001:2008, CE, EC and
should Comply with latest European Guidelines
2 Incubator
1. Interior : approx Size 295 mm X 262 mm X 300
mm.(hxwxd)
2. Exterior: ST Powder coated
3. External Dimensions: approx 620 mm high, 370mm Wide,
420 mm deep.
4. Shelving: (3) Shelf positions (2) shelves supplied.
5. Shelf Spacing : Useable space between shelves 80 mm.
6. Heating: 0.7KW Stainless sheathed element.
7. Control system: Microprocessor control System with large
bright
8. Digital temperature display system incorporates control
9. Failsafe functions.
10. Temperature Range: 50 to 200 Degree C max. (Other
Ranges available).
11. Accuracy: + 0.1 degree C at sensor.
3 Full automatic Ethylene Oxide Sterilizer
This equipment is an ethylene oxide gas sterilizer used for
the sterilization of medical disposables for heat sensitive
products like probes, catheters, endoscopes etc. The
chamber and all contact parts are made from Stainless Steel
304. It has a single door arrangement with a silicon gasket
for leak proof operation.
EQUIPMENT DESCRIPTION
The sterilizer consists of:
Chamber: Single door, stainless steel
Chamber Size : 5CFT (140 Ltr)
With Following Systems.
· heating system,
· vacuum system
· humidity system
· 0.2 micron ultra fine air inlet filter,
· programmable controller.
· alphanumeric LCD display
· ENVIRO-PRO system
Steridium /
Charmie/Memmert/
Medicraft Ept.
Taxus/Steridium/3M/
PCI

The chamber as well as the door should made from stainless
steel. The door is provided with a silicon rubber gasket to
ensure leak proof operation.
The entire machinery should housed inside a single cabinet.
Easy access for maintenance is obtained by opening the
doors of the cabinet the system temperature is selectable
and the chamber is electrically heated.
The chamber has a cartridge breaking system, which breaks
the gas-containing cartridge inside the chamber during the
process.
The electrical and electronic control and indicating
equipment should housed in the same cabinet. Audiovisual
indication and a powerful and sturdy microprocessor ensure
reliable and safe operation every time; and in case of fault
provide the operator with correct information regarding the
fault.
Control Facility:
The Machine should provide two types of controls for our
sterilizer: Automatic as well as Manual
In AUTO MODE :
In AUTO mode , the sterilization is a one – touch operation ;
where the operator loads the material in the trolley provided
along with
the machine , closes the door and then presses the Start
button to initiate the cycle; the cycle then its own and after
sterilizing and aerating the load; informs the operator that
the cycle is complete.
The sterilizer automatically performs all stages of
sterilization treatment using ethylene oxide, with control of
the essential parameters:
· vacuum / pressure / humidification / contact time
(exposure period) / chamber temperature / aeration of
load
In MANUAL MODE :
In case of unforeseen problems occurring in the machine,
there is a provision to changeover from AUTO mode to
MANUAL mode; for operating the machine in Manual Mode.
A separate set of operating switches are provided to enable
the operator to take a cycle in manual mode also.
Display & Printouts
The alphanumeric green display shows the various cycle
statuses and displays the current time, the date, the batch
no., the time remaining in Gas exposure phase, the time
remaining in the Aeration phase. Besides this the display also
shows the various parameters, and the actual error and also
the error code as and when applicable.

The printer indicates the various parameters like the Start
time, End time, Date, the batch no. and the operator’s ID
mark, errors and error codes, the various parameters, Gas
exposure time, Aeration Time as and when applicable.
Safety Features:
·All sensors linked to the automation ensure reliability and
failsafe operation.
·Every cycle there is a Leak test period; which checks the
leakage and aborts the cycle if there is a leakage in the
system.
·Locked door sensor during cycle
·Constant watch over entries and break diagnostic from
automation, which warns the operator, by means of
messages on indicator and buzzer.
·Cycle completion record is shown on the printout.
·Auto - Abort facility in case of abnormal conditions.
·Three degassing cycles, before aeration starts, to enhance
removal of residual EO.
Special Features
·Stainless steel chamber and fittings.
·Special easily operable flat door with interlock for added
safety.
·Evacuation of chamber during washing cycle and aeration is
programmable.
·Auto – Manual Changeover possible in case of failure of
auto system.
·Password Protection to change of instructions.
Disposable Items:
1. ETO Cartridge – 10 Nos.
2. Sterie Roll – 5cm, 7.5cm, 10cm, 15cm, 20cm,& 25cm. – 2
each
4 Auto Control Panel for Autoclave (two nos.)
• standard plc control system based on the hi-tech
state of the art micro-processor circuit technology,
ensuring a complete automatic operations along with
high efficiency and great reliability.
• 100% automatic operation throughout the sterilization
cycle of both the horizontal autoclave ( Surgikraft &
Medicare Eqpt. make).
• No intermediary human intervention should be
required after choosing the parameters and initiating
the sterilization process in the autoclaves..
• The primary cycle phase and the actual parameters of
the horizontal autoclave and along with set values
should be displayed on the LCD panel during the entire
cycle progress.
Modi /Shrijee Surgical

• The main parameters of the process such as,
temperature, pressure, time should be controlled and
displayed, on the LCD panel of the system.
• Ergonomically designed keyboard located on the front
level should enable the user to choose the desired
program, initiate and terminate the cycle, and allow a
trained technician to preset the main parameters using
an access code.
• Easy to use, user friendly and fully programmable.
• For a elaborate and presentable documentation of
cycle process, the logic control unit should be
provided with a diligent wipro/epson dot matrix
printer, which is connected to the central
microprocessor system.. The printer should generate
a hard copy of the printout of the relevant or
desired information relating to the cycle operation like
the pressure , sterilization time, temperature at any
given/preset time interval, vacuum, and drying time,
number of cycles, number of pulsing etc.
• The PLC control system is designed to operate up to six
standard sterilization programs between 105oC and
137oC and two test programs optional and selectable
through keyboard on the panel. Other parameters such
as air removal, sterilization and drying stages should be
programmable.
• Fully Automatic operation; cycle begins by press of the
START button.
• Initial air purging cycle; at the beginning air is
automatically removed from the chamber.
• Microprocessor based Digital Temperature Indicator
Controller. Controls temperature / pressure precisely
at set value.
• In built adjusted digital timer; programmable as per
sterilization load requirement.
• Automatic steam exhaust at the end of cycle.
• Unique microprocessor temperature controller
provides facility to program the cycle, with a feather
touch panel.
• Auto control Panel with LCD Display
• Shows Down Times
• Display of Status
• Easy setting of Six type of different Programs in six
different temperature
• 10 Memory Save Cycle
• Online printing & Self-Temperature setup.

Annexure – 11
Department of General OPD & Wards
S.N Technical Specifications of Equipment Mfg. Co. Preferred
1 Fogging Machine
Specifications:
• Tank Capacity: 7.5 ltrs (HDPE – Engg. Plastic grade non
corrosive).
• Tank with graduated marking and liquid level visibility
from outside. Range from 1 litre ~ 7.5 litres in step of
0.5 litres.
• With Attached “Electronic Timer Device” to run for 60
mins. in absence of attender.
• Aluminium Power Head Housing corrosion resistant &
SS304 fittings.
• Nozzle Assembly: Non rotating, Non clogging & Vortex
design.
• Liquid line connectors/Strainers & Wire mesh SS 304.
• Air-Filter with attached rubber ring & SS clamp.
• Area coverage: Upto 10,000 cu. fts.
• Liquid discharge rate: 0 ~ 300 ml/min. (Adjustable with
“Flow Control Mechanism).
• Volume of Airflow: 3.00 ~ 4.00 cubic mtr/min.
• Pressure Clamp and leak proof fittings.
• Reach: > 10 mtrs distance & > 5 mtrs height.
• Particle Size: 1 ~ 40 microns (Adjustable with “Flow
Control Mechanism”).
• Rotating Knob: Available in SS 304 & Plastic Make.
• 230 volts / 50 Hz. AC current.
• Motor speed: 20,000 RPM.
• Motor Type: High Thrust Double Stage/Impellor motor
with Class B insulation, inbuilt circuit for thermal
overload protection.
• Motor CFM: 105 Cubic Fts/min.
• Motor Rating: 120 minutes.
• 7 Kgs. Light weight and portable.
• All fitting components SS304 only.
• Spares: Extra Air Filter.
Galtron/J&J/PCI/
Radiant/Idealine/Skan/
Aspee

2 Nebulizer
•With V.V.T. (Virtual Valve Technology) nebulizer kit, for
efficient delivery of medication
•without silicon valve
•High Nebulization rate ensuring optimized treatment
duration
•Leaves minimal residual medication
•Easy to operate and maintain, with easy-to-clean
Nebulizer kit without silicon valves
V.V.T. Nebulizer kit- 2 Nos.
3 Fetal Doppler
1. Doppler should display beat to beat measurement of FHR of
Foetus & Adult.
2. It Should have 1 TRANDUCERS Clinical Hand Probe of Plastic
body with Crystal and Metal Handle.
3. Individually adjustable Bradycardia/Tachycardia FHR limits
with audio /visuals Alarms.
4. Alarms Silence Facility.
5. On power OFF alarms settings should remain unchanged.
6. It should have facility to measure Foetal & adult heart rate.
7. It should have clamp for holding the transducer probe.
8. Mains as well as battery operated.
9. Feather touch key operated volume control.
10. Highly sensitive ultrasonic beam permits hearing the Foetal
heart beats clearly from 10-12th week of pregnancy.
11. The output can be presented in two different ways:
a. Built in speaker b. Display readout
12. Compact, lightweight, portable ABS cabinet.
Applications:
Detection of foetal heart at 10 to 12 weeks
Localization of Placenta.
Detects Foetal Distress & Intrauterine death.
Determine multiple pregnancies
Accessories:
Transducer Probe with cable, Oil Bottle
Carrying case, Mains Adaptor
Technical Specifications:
1] Body: Shock proof
2] Battery: 6 X 1.5 v D size
3] Mains adaptor
4] Frequency: 2 MHz
5] Weight: 1kg
Omron/Nulife/
Morepen/Philips
Galtron/BPL/Teksonic

4 Electric Needle Destroyer
With Needle Cutting and cap burning facility
5 Electric Suction Machine LIPO fully stainless steel body
Rotary High-Vac are double stage pumps of larger capacities,
which are known as Lipo for fats extraction and full in cosmetics
surgery, the main assembly of the pump consist of a stator with
a rotor mounted eccentrically in it. The rotor is fitted with two
spring loaded diametrically opposed vanes, which move in and
out of their slots pressing against the inner surface of the stator
these are oil sealed self lubricated, silent running, it is designed
to achieve maximum vacuum in a very short time, it reduce the
wear and tear of its components and makes it suitable for
noiseless and trouble free performance for years and thus helps
in reduction of repair bills, these are very compact but so simple
in design that all minor repairs in case of need can be carried
out easily, it run continuously for many hours at a time. The
entire pump and motor are placed in an attractive solid
STAINLESS STEEL cabinet having steel top, which is giving extra
protection, reduces heat noise and vibration to the minimum
the suction mechanism is oil immersed. The unit is mounted on
smooth moving ball bearing heavy-duty castors, and noiseless. It
crates vacuum of 700 to 760mm of Hg (28” to 30”) the suction
system is accurately controlled and precisely regulated by knob
this unit is fitted with filter and automatic cut off by float
mechanism, vacuum gauge, pilot light and protection fuse, this
unit is fitted with 1/2HP ball bearing double shaft motor
working on 220-250V single phase 50cycle Suction Capacity:
25Lts /p minutes Max Vacuum: 700mm to 760mm of Hg
Consumption: ½ HP Voltage: 220 V 50 Cycles Castors: 5cm
Antistatic Weight: Approx 43kg Dimensions: 38cmx38cmx85cm
with castor Sound: almost whispers Finish: SS cabinet Suction
Jar: 2nos 2500ml with over flow safety device
6 Autoprocessor
1. should process sheet films.
2. film size min-4x4 ad max 14x17.
3. Tank volume 5litres.
4.Developer temp 30 to 37 deg adjustable
5. fixer temp 30 to 37 deg adjustable.
6. Direr temp 70 deg max.
7. Replenishment tanks-25 litres.
8. Facility for anti crystallization ad anti oxidation
programme.
9. it should have international standards ad safety
requirements.
10. should be light weight 40 to 50 kgs.
11. dimension app:80cmsx60x44 or less.
12.heat emission should be less than1.5kj/sec
Omron/Nulife/Metco/
Mehta Surg.
Brightlite/Supreme/
Hira/Galtron/SPI/
Anand
Chhayagraphics/
Prognosys Medical

13. power consumption less than 1.5kwh during
processing.
14. auto manual filling of chemicals.
15chemical circulation continuous.
16film in feed by detection switch.
17. Processing time100/167 sec.
18. Special requirements: manufactures ad suppliers
should have own manufacturing unit in India with good
service backup.
Company should have iso9001 standards and CE
certification also.
19. Machine should have two piece body shell.

Annexure – 12
Solar Water Heater System
Sr.
No.
Description Quantity*
1.
Labor room/NICU
Solar water heating system
Capacity 1500 liters per day
1 no.
2. Cold water hdpe tank capacity 1000 ltrs isi
1 no.
3 Stand for cold water tank
1 no.
4 Cold water piping gi b class / kitec
20 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum aluminium
cladding
35mtrs
6 Electrical backup tank capacity: 500 liters with
control panel
Gynecology ward
1 no.
1. Solar water heating system
Capacity 2500 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs isi
1 no.
3 Stand for cold water tank 1 no.
4 Cold water piping gi b class / kitec
22 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum aluminium
cladding
45 mtrs
6 Electrical backup tank capacity: 500 liters with
control panel
Surgical/OT
1 no.
1. Solar water heating system
Capacity 800 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs isi
1 no.
3 Stand for cold water tank 1 no.

4 Cold water piping gi b class / kitec
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum aluminium
cladding
6 Electrical backup tank capacity: 250 liters with
control panel
Deluxe/Male medical ward
1. Solar water heating system
Capacity 3000 liters per day
20 mtrs
30mtrs
1 no.
1 no.
2. Cold water hdpe tank capacity 500 ltrs isi
3 Stand for cold water tank
1 no.
1 no.
4 Cold water piping gi b class /kitec
30 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum aluminium
cladding
94 mtrs
6 Electrical backup tank capacity: 500 liters with
1 no.
control panel
Pediatric/ orthopedic/Female medical
1. Solar water heating system
Capacity 2500 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs isi
3 Stand for cold water tank
1 no.
1 no.
4 Cold water piping gi b class
30 mtrs
5 Hot water piping
Gi b class
Insulation: rockwool 48 kg/ cum aluminium
cladding
90 mtrs
6 Electrical backup tank capacity: 500 liters with
1 no.
control panel
Trauma
1. Solar water heating system
Capacity 800 liters per day
2. Cold water hdpe tank capacity 500 ltrs isi
1 no.
1 no.

3 Stand for cold water tank 1 no.
4 Cold water piping gi b class /kitec
20 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum aluminium
cladding
45 mtrs
6 Electrical backup tank capacity: 250 liters with
control panel
1 no.
*The above quantities are approximate and hence may differ slightly at the
time of installation which will be under the scope of the successful bidder.
SCOPE OF WORK:
A) Supply & installation of solar collectors on flat surface.
B) Supply & installation of insulated hot water tank of mentioned
capacity.
C) Supply & installation of system piping.
D) System designing.
E) Testing & commissioning of the system.

Annexure – 13
General Instruments
Sr. No Particulars Total Mfg Company
1 Needle Holder 8" 112
2 Needle Holder 6" 127
3 Needle Holder 4" 20
4 Needle Holder 10" 15
5 Gauze Cutting Scissor 35
6 Artery forcep(curved)6' 243
7 Cockers 8" 40
8 S.S Drum12*15 50
9 S.S Drum10*9 55
10 S.S Drum10*5 24
11 Tooth Forcep6" 110
12 Sponge Holder 8" 118
13 Speculum 20
14 S.S tray 12*8" 63
15 S.S tray 9*6" 40
16 S.S tray 12*10" 25
17 Enema set 3
18 x-ray Hanger12*15" 30
19 x-ray Hanger11*15" 30
20 x-ray Hanger10*12" 30
21 x-ray Hanger10*8" 30
22
x-ray Devloping tank cover,22.5
ltr
3
23 Mayo scissor 8" 89
24 Mayo scissor 6" 35
25 Mosquito artery curved 4" 97
26 Scoop 19
27 Suture cutting scissor 38
28 Skin stappler remover 14
29 s. s Bowl small 201
30 s. s Bowl 4" diameter 55
31 Metzen bone scissor straight 20
32 b.p. handle No. 3 27
33 b.p. handle No. 4 25
34 mosquito artery straight 4" 35
35 Allies 6" 95

Sr. No Particulars Total Mfg Company
36 Allies 4" 20
37 Hammer 11
38 paed. Ambu bag 1 Liter 7
39 Adson tooth forceps 22
40 E.T Tube stilet (adult) 32
41 laryngoscope bulb 65
42 Bipap mask( adult) 3
Portabale ventilator circuit-
Double Water Trap
1
43 (Autoclavable)
44 linen trolley 1
45 mayo trolley four rails big 1
46 F.B.Hook 2
47 Hookson Hook 1
48 Fine Scissor 20
49 Tuff scissor 10
50
Tracheostomy set (single
puncture)
51 Bone holding forcep(humerous)
2
52 Bone holding forcep(tibia) 1
53 Bone holding forcep(Femur) 2
54 Flexible fix head reamer no. 11
1
55 O2 Mask paed 5
56
laparoscopic trocar
(versapotNo.10)
2
57
laparoscopic trocar
(versapotNo.12)
2
58 Mariland 2
59 Laparoscopic bap Cock 4
60 Laparoscopic alliz 2
61 Monopolar cautry cord 50
62 Bipolar Cautry (curved point) 2
63 Formalin chamber big 2
64 Formalin chamber smol 2
65
Hand reamer 8 to 13
(tibia/Femur)
53
1 set
66 Hand reamer 4 to 7 (Humurous)
1set
67 Punch 3

Sr. No Particulars Total Mfg Company
68 Periosteum Small 2
69 Periosteum Small Curved 2
70 Periosteum Large 2
71
Intestinal clamp non crushing
curved
6
72
Intestinal clamp non crushing
straigst
6
73 Bur perforator for cramiotimy 1 set
74 Reservoir bag 2 Ltr 5
75 Reservoir bag 2.5 Ltr 5
76 Turp loop (indian) 10
77 Bain circuit for troley 5
78 JRO circurt Paed 2
79 Retrograbe Dialator 1
80 Uretic cathetor fr. 3,4,5 2 each
81 Double D. J .Stent Fr 3,4,5 2 each
82 Sclero Therapy Needle 10
83 Plier 5
84
Nibbler (Rounger) 30 Degree
Bent
5
85 Nibbler (Rounger) Straigst 5
86 Nibbler (Rounger) Large 5
87 Nibbler (Rounger) Small 5
88 Man Man Key 10
89 Awl for tibia 2
90 Awl for femur 2
91 Awl Long Handel For femur 1
92 Awl For Radius 2
93 Blunt Disscetor 5
94 Hammer for Ortho Small 2
95 Hammer for Ortho Midium 2
96 Hammer for Ortho heavy 2
97 Homan Retractor 2 set
98 T.Handle For K-Wire 5
99 Hand Dril 1
100 Shanez Pin T. handle 2
101 Uterin Holding for ceps 3
102 Deavers Medium Sige 5
103 Tongue Deprassor 12
104 Fistila Probe 5
105 Mixtard 3 Pair

Sr. No Particulars Total Mfg Company
106 Suprapubic Trocher 2
107 Suctiom Tip Multipores 4 To 1
2 Set
108
Scissor For Plastic Suragiry
3"(metzenbaum)
5
109 Towel Clip 65
110 Cannulated Screw Driver 4.5 2
111 Cannulated Dril Bit 6.5 3
112 Bone Marrow Needle no. 16 S.S
113
Small Size Spike For
R/U/Humerous
2 Set
114
Plate Holding Forceps
R/U/Humerous
1 Set
115 Proseal LMA No. 3-4 2 Each
116
Combined Spinal 27G Epidural
Needle16 G
20
117 Epidural needle 16G 10
118 Epidural Catheter No.16 20
119 Cord Holding For ceps 4
Non scalpal Vasectomy NSV Hook 4 Each
120 Vas Holding Forceps
121 AO Drill Bit 3.5 3
122 AO Drill Bit 4.5 3
123 AO Drill Bit 2.5 3
124 Counter synk 3.5 1
125 Counter synk 4.5 1
126 Acetabulum Retractor (all Sizes)
127
Wire cutter (Tumy Sleeve tip) For
2 mm
128
Wire cutter (Tumy Sleeve tip) For
5 mm
1
129 AO Tap 3.5 mm 1
130 AO Tap 4.5 mm 1
131
Dissecting sleeve With Tumy
Sleeve Tip
3
132 Bone Cutter Small 2
133 Bone Cutter Heavy 2
20
1
1

Sr. No Particulars Total Mfg Company
134
Osteotome set All Sizes With
Wooden Handle (AO)
1
135 Adaptor For Suction (Steel) 2
136 IDL Mirror 4
137 Siegels Pneumetic Speculum 2
138 T Elevator 8
139 Mouth Mirror 45
140 Upper Anterior forceps 10
141 Third Molar Forceps 9
142 Hockey stick (Dental) 7
143 Mouth Gag 3
144 Magles forcep 6
145 Nasal Speculun 5
146 Plastic kidney tray (blue) 148
147 IOL Manipulater( Blunt edge) 4
148 Lim's tooth Forceps 5
149 Plain forceps (Opthalmic) 5
150 Wire Vectis 4
151 Phaco Choppper Sharp end 1
152 Tunnel Knife 50
153 Phaco Sleeve 5
154 Phaco Tubing Set 2
155 Keratoplasty set 1
156 Diamond knipe 1
157 Endocapsuler Tension Rings 10
158 Iris Hook (self Retaining) 4
159 Silicon Sling for Ptosis 5
160 Rhexcis Forceps 2
161 Vitrectomy cutter 1
162 Glass Syringe 10 ml,5ml,2ml 20 each
163 AC Maintainer 5
164
165
V P Shunt Introducer (Adult)
All Size
V P Shunt Introducer (Paed)
All Size
Preferred Manufacturing Company is mentioned by the department on
Schedule of Requirement, Specification and allied technical Details.
1
1

Annexure – 14
(FORMAT OF AUTHORIZATION LETTER FOR AUTHORIZED
DISTRIBUTOR)
I / We hereby declare that....
1. M/s.
________________________________________________________________
___is our authorized distributor for our products in India from date and they
are authorized to quote and follow up on our behalf and the said agreement is
valid in force as on date;
2. I/We undertake to supply the drugs / items for which the quotations of
following items are submitted by
M/s.__________________________________________on our behalf in
respect of Tender Enquiry # :___________________________
Sr.No. Item No. Name of Item
(1)
(2)
3. I / We have read all the terms and conditions of the tender enquiry and the
same are irrevocably binding upon us till the expiry of the contract signed &
executed on our behalf;
4. I/We shall notify the Medical Superintendent, Shree Vinoba Bhave Civil
Hospital, Silvassa. immediately if there is any change in the agreement
between M/s. _____________________________and me/us regarding
authorized distributorship of our products and further undertake to supply the
items quoted by the distributor on my / our behalf at the quoted in the tender
enquiry in case of such a change of agreement.
5. This authority is applicable only for Tender Enquiry of Shree Vinoba Bhave
Civil Hospital, Silvassa. Annual E Tender for Year 2012-13 due on
______________.
Date:-
Signature of Authorized Signatory

Annexure - 15
Specifications of Medical Equipments for Department of
__________________________________________
(Department name to be filled by the bidder)
S.N Name of
Equipment
Mfg
Company
Preferred
Mfg
Company
quoted
Y/N/D Deviation if any

Annexure – 16
Price Schedule of Solar Water Heater System
Sr.
No.
Description
Labor room/NICU
Quantity* Unit Rate
1. Solar water heating system
Capacity 1500 liters per day
1 no.
2. Cold water hdpe tank capacity 1000 ltrs
isi
1 no.
3 Stand for cold water tank
1 no.
4 Cold water piping gi b class / kitec
20 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum
aluminium cladding
35mtrs
6 Electrical backup tank capacity: 500 1 no.
liters with control panel
1.
Gynecology ward
Solar water heating system
Capacity 2500 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs
isi
1 no.
3 Stand for cold water tank 1 no.
4 Cold water piping gi b class / kitec
22 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum
aluminium cladding
45 mtrs
6 Electrical backup tank capacity: 500
liters with control panel
Surgical/OT
1 no.
1. Solar water heating system
Capacity 800 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs
isi
1 no.
3 Stand for cold water tank 1 no.

4 Cold water piping gi b class / kitec
20 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum
aluminium cladding
30mtrs
6 Electrical backup tank capacity: 250
liters with control panel
Deluxe/Male medical ward
1 no.
1. Solar water heating system
Capacity 3000 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs
isi
1 no.
3 Stand for cold water tank 1 no.
4 Cold water piping gi b class /kitec
30 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum
aluminium cladding
94 mtrs
6 Electrical backup tank capacity: 500
liters with control panel
Pediatric/ orthopedic/Female medical
1 no.
1. Solar water heating system
Capacity 2500 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs
isi
1 no.
3 Stand for cold water tank 1 no.
4 Cold water piping gi b class
30 mtrs
5 Hot water piping
Gi b class
Insulation: rockwool 48 kg/ cum
aluminium cladding
90 mtrs
6 Electrical backup tank capacity: 500
liters with control panel
Trauma
1 no.
1. Solar water heating system
Capacity 800 liters per day
1 no.
2. Cold water hdpe tank capacity 500 ltrs
isi
1 no.

3 Stand for cold water tank 1 no.
4 Cold water piping gi b class /kitec
20 mtrs
5 Hot water piping
Gi b class / kitec
Insulation: rockwool 48 kg/ cum
aluminium cladding
45 mtrs
6 Electrical backup tank capacity: 250
liters with control panel
1 no.
The total Cost of the Solar water Heater Plant is
___________________(in figures)
___________________________________________________________
__________________________________________________(in words)
The above cost includes all the installation, commissioning,
transportation and training charges. No other charges will be borne by
the Hospital other than the rates mentioned above.
Signature:
Stamp:

Annexure – 17
Price Schedule for General Instruments
Sr. No Particulars Total Unit Rate Total
1 Needle Holder 8" 112
2 Needle Holder 6" 127
3 Needle Holder 4" 20
4 Needle Holder 10" 15
5 Gauze Cutting Scissor 35
6 Artery forcep(curved)6' 243
7 Cockers 8" 40
8 S.S Drum12*15 50
9 S.S Drum10*9 55
10 S.S Drum10*5 24
11 Tooth Forcep6" 110
12 Sponge Holder 8" 118
13 Speculum 20
14 S.S tray 12*8" 63
15 S.S tray 9*6" 40
16 S.S tray 12*10" 25
17 Enema set 3
18 x-ray Hanger12*15" 30
19 x-ray Hanger11*15" 30
20 x-ray Hanger10*12" 30
21 x-ray Hanger10*8" 30
22
x-ray Devloping tank cover,22.5
ltr
3
23 Mayo scissor 8" 89
24 Mayo scissor 6" 35
25 Mosquito artery curved 4" 97
26 Scoop 19
27 Suture cutting scissor 38
28 Skin stappler remover 14
29 s. s Bowl small 201
30 s. s Bowl 4" diameter 55
31 Metzen bone scissor straight 20
32 b.p. handle No. 3 27
33 b.p. handle No. 4 25
34 mosquito artery straight 4" 35
35 Allies 6" 95

Sr. No Particulars Total Unit Rate Total
36 Allies 4" 20
37 Hammer 11
38 paed. Ambu bag 1 Liter 7
39 Adson tooth forceps 22
40 E.T Tube stilet (adult) 32
41 laryngoscope bulb 65
42 Bipap mask( adult) 3
Portabale ventilator circuit-
Double Water Trap
1
43 (Autoclavable)
44 linen trolley 1
45 mayo trolley four rails big 1
46 F.B.Hook 2
47 Hookson Hook 1
48 Fine Scissor 20
49 Tuff scissor 10
50
Tracheostomy set (single
puncture)
51 Bone holding forcep(humerous)
2
52 Bone holding forcep(tibia) 1
53 Bone holding forcep(Femur) 2
54 Flexible fix head reamer no. 11
1
55 O2 Mask paed 5
56
laparoscopic trocar
(versapotNo.10)
2
57
laparoscopic trocar
(versapotNo.12)
2
58 Mariland 2
59 Laparoscopic bap Cock 4
60 Laparoscopic alliz 2
61 Monopolar cautry cord 50
62 Bipolar Cautry (curved point) 2
63 Formalin chamber big 2
64 Formalin chamber smol 2
65
Hand reamer 8 to 13
(tibia/Femur)
53
1 set
66 Hand reamer 4 to 7 (Humurous)
1set
67 Punch 3

Sr. No Particulars Total Unit Rate Total
68 Periosteum Small 2
69 Periosteum Small Curved 2
70 Periosteum Large 2
71
Intestinal clamp non crushing
curved
6
72
Intestinal clamp non crushing
straigst
6
73 Bur perforator for cramiotimy 1 set
74 Reservoir bag 2 Ltr 5
75 Reservoir bag 2.5 Ltr 5
76 Turp loop (indian) 10
77 Bain circuit for troley 5
78 JRO circurt Paed 2
79 Retrograbe Dialator 1
80 Uretic cathetor fr. 3,4,5 2 each
81 Double D. J .Stent Fr 3,4,5 2 each
82 Sclero Therapy Needle 10
83 Plier 5
84
Nibbler (Rounger) 30 Degree
Bent
5
85 Nibbler (Rounger) Straigst 5
86 Nibbler (Rounger) Large 5
87 Nibbler (Rounger) Small 5
88 Man Man Key 10
89 Awl for tibia 2
90 Awl for femur 2
91 Awl Long Handel For femur 1
92 Awl For Radius 2
93 Blunt Disscetor 5
94 Hammer for Ortho Small 2
95 Hammer for Ortho Midium 2
96 Hammer for Ortho heavy 2
97 Homan Retractor 2 set
98 T.Handle For K-Wire 5
99 Hand Dril 1
100 Shanez Pin T. handle 2
101 Uterin Holding for ceps 3
102 Deavers Medium Sige 5
103 Tongue Deprassor 12
104 Fistila Probe 5
105 Mixtard 3 Pair

Sr. No Particulars Total Unit Rate Total
106 Suprapubic Trocher 2
107 Suctiom Tip Multipores 4 To 1
2 Set
108
Scissor For Plastic Suragiry
3"(metzenbaum)
5
109 Towel Clip 65
110 Cannulated Screw Driver 4.5 2
111 Cannulated Dril Bit 6.5 3
112 Bone Marrow Needle no. 16 S.S
113
Small Size Spike For
R/U/Humerous
2 Set
114
Plate Holding Forceps
R/U/Humerous
1 Set
115 Proseal LMA No. 3-4 2 Each
116
Combined Spinal 27G Epidural
Needle16 G
20
117 Epidural needle 16G 10
118 Epidural Catheter No.16 20
119 Cord Holding For ceps 4
Non scalpal Vasectomy NSV Hook 4 Each
120 Vas Holding Forceps
121 AO Drill Bit 3.5 3
122 AO Drill Bit 4.5 3
123 AO Drill Bit 2.5 3
124 Counter synk 3.5 1
125 Counter synk 4.5 1
126 Acetabulum Retractor (all Sizes)
127
Wire cutter (Tumy Sleeve tip) For
2 mm
128
Wire cutter (Tumy Sleeve tip) For
5 mm
1
129 AO Tap 3.5 mm 1
130 AO Tap 4.5 mm 1
131
Dissecting sleeve With Tumy
Sleeve Tip
3
132 Bone Cutter Small 2
133
Bone Cutter Heavy
2
20
1
1

Sr. No Particulars Total Unit Rate Total
134
Osteotome set All Sizes With
Wooden Handle (AO)
1
135 Adaptor For Suction (Steel) 2
136 IDL Mirror 4
137 Siegels Pneumetic Speculum 2
138 T Elevator 8
139 Mouth Mirror 45
140 Upper Anterior forceps 10
141 Third Molar Forceps 9
142 Hockey stick (Dental) 7
143 Mouth Gag 3
144 Magles forcep 6
145 Nasal Speculun 5
146 Plastic kidney tray (blue) 148
147 IOL Manipulater( Blunt edge) 4
148 Lim's tooth Forceps 5
149 Plain forceps (Opthalmic) 5
150 Wire Vectis 4
151 Phaco Choppper Sharp end 1
152 Tunnel Knife 50
153 Phaco Sleeve 5
154 Phaco Tubing Set 2
155 Keratoplasty set 1
156 Diamond knipe 1
157 Endocapsuler Tension Rings 10
158 Iris Hook (self Retaining) 4
159 Silicon Sling for Ptosis 5
160 Rhexcis Forceps 2
161 Vitrectomy cutter 1
162 Glass Syringe 10 ml,5ml,2ml 20 each
163 AC Maintainer 5
164
165
V P Shunt Introducer (Adult)
All Size
V P Shunt Introducer (Paed)
All Size
The above mentioned rates are including all freight & taxes.
Sign:
Stamp:
1
1