Sensor systems 2 AS-Interface

Recommendations

Info

VBA-2E-KE2-I/U Masters and Gateways Power Supplies, Extender, Repeaters Safety at work I/O Modules Control cabinet I/O Modules Field application Analogue modules Other modules Inductive sensors Photoelectric sensors Rotary encoders Accessories AS-Interface analogue module Order code VBA-2E-KE2-I/U KE control cabinet module 2 analogue inputs Features Housing with removable terminals Communication monitoring Addressing jack Supply of inputs external or from the module, as required Function indication for bus, internal and external sensor power supply, inputs 204 A D Spec 2.1 Dimensions Electrical connection AS-Interface - AS-Interface + ADDR U AUX + U AUX - 22.5 7 85 U+ U- Plug-in jumpers Indicating/operating means 2 ON OFF EXT INT . .. VBA-2E-KE2-I/U Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group Tel.: Germany +49 621 776-0 USA +1 330 4253555 Singapore +65 67799091 Internet http://www.pepperl-fuchs.com µP Vor dem Öffnen alle Anschlüsse spannungsfrei schalten / de-energize all connections before opening 1 Entriegeln / unlock Auf BEIDEN Seiten drücken / press on BOTH sides 2 Öffnen / open Oberteil bis zum STOPP herausziehen / pull upper part until STOP 3 Schalter einstellen / set switches INT= Sensorversorgung aus AS-Interface / sensor supply from AS-Interface EXT= Sensorversorgung extern / external sensor supply 2 ON= Kanal 2 an / Channel 2 on 2 OFF= Kanal 2 aus / Channel 2 off 3 1 2 4 7 5 6 8 24V ext. Sig + Sig - 0V ext. + Sig + Sig - - I1 Sig+ I2 Sig+ I1 Sig- I2 Sig- 99 2-wire 3-wire 4-wire + U+ U+ - I/U I/U+ 24V ext. 24V ext. PWR AUX ADDR U- I/U- U- Connections Input 1 I1 Sig. + 2 I1 Sig. - 3 24 V ext. 4 0 V ext. 5 I2 Sig. + 6 I2 Sig. - 7 24 V ext. 8 0 V ext. 9 U1 Sig. + 10 U1 Sig. - 11 U2 Sig. + 12 U2 Sig. - 13 AS-Interface + 14 AS-Interface - 15 AUX + 16 AUX - 0V ext. 0V ext. INPUT 1 2 1 2 U OK I FAULT INT U1 Sig+ U1 Sig- U2 Sig+ U2 Sig- AS-i+ AS-i- AUX+ AUX- Beschriftungsfeld / label field Issue date 2004-11-19 - Catalogue AS-Interface 2004/2005
Issue date 2004-11-19 - Catalogue AS-Interface 2004/2005 AS-Interface analogue module Technical data Indicators/operating means LED FAULT error display; LED red red: communication error red flashing: periphery fault LED INT Internal input voltage active; LED green LED PWR AS-Interface voltage; LED green LED AUX ext. auxiliary voltage UAUX ; LED green LED -/OK Status input signal; LED green Off: Not connected (Only current module) On: Signal within measuring range Flashing: Signal outside measuring range LED U/I Current or voltage module; Green LED Off: Voltage input On: Current input Electrical specifications Auxiliary voltage (output) UAUX 24 V DC ± 15 % PELV (protection class 3 according to VDE 0106/IEC 364-4-41) Insulation voltage Ui ≥ 500 V Rated operational voltage Ue 26.5 ... 31.6 V from AS-Interface Rated operational current Ie ≤ 80 mA Input Number/Type 2 analogue inputs Current: 4 ... 20 mA voltage: 0 ... 10 V Supply from AS-Interface or from external auxiliary voltage as required UAUX Current loading capacity ≤ 40 mA per input Input resistance For current module: 50 Ω For voltage module: 100 kΩ Switching point Changeover current/voltage module: current module with Iinput ≥ 1 mA voltage module with Uinput ≥ 1 V Resolution 16 Bit / 1 µA (Current module) or 16 bit / 1 mV (Voltage module) Programming instructions Profile S-7.3.D IO code 7 ID code 3 ID2 code D Data bits (function via AS-Interface) The transfer of the data value is based on AS-Interface Profile 7.3. Parameter bits (programmable via AS-i) function P0 mains power frequency filter P0=1, 50 Hz filter active P0=0, 60 Hz filter active P1 projecting of the 2nd channel P1=1, channel 2 is projected P1=0, channel 2 is not projected P2 Message of peripheral error P2=1, periphery fault is reported P2=0, periphery fault is not reported P3 not used Standard conformity Electromagnetic compatibility EN 50295, EN 61326 Ambient conditions Ambient temperature 0 ... 70 °C (273 ... 343 K) Storage temperature -25 ... 85 °C (248 ... 358 K) Mechanical specifications Protection degree IP20 according to DIN 40050 Connection removable terminals, terminal connection ≤ 2.5 mm 2 Mass 350 g Mounting DIN rail Function VBA-2E-KE2-I/U The VBA-2E-KE2-I/U analog module is equipped with two analog inputs that can be current inputs (4 mA ... 20 mA) or voltage inputs (0 ... 10 V). The module can also be connected as a combined current/voltage module. In this case the module type must be the same for each channel. Depending on the setting of the internal sliding switch, the power supply for the measurement value transmitter is via the module (from the AS-Interface) or through an external power supply. The input power supply selection is displayed via the INT and AUX LEDs. Measurement values are converted and data is transferred asynchronously based on AS- Interface Profile 7.3. The resolution of analog values is 16 bits with a value range of 4,000 ... 20,000 (current module) or 0 ... 10,000 (voltage module). Power faults can be eliminated with a parameterizable filter (50 Hz/60 Hz) in the A/D converter. The second channel can be turned off with a second slide switch to allow for faster data transfer. The housing, only 22.5 mm in width, takes up little place in the switch cabinet. The module is installed by snapping on the 35-mm carrier rail in accordance with EN 50022. It can be connected by plug-in terminals (COMBICON). 4X terminal blocks (black) are used for the inputs. The connection of the external auxiliary supply and AS-Interface is made through the 2-way-terminal blocks (auxiliary supply gray, AS-Interface yellow). This makes it possible to separate individual sensors or to supply power during commissioning or servicing. Note: The device is equipped with communication monitoring that turns off the outputs if no AS- Interface communication has taken place with the device for more than 40 ms. An overload of the internal input supply is reported by the 'periphery error' to the AS- Interface master. Communication over the AS-Interface remains in effect. Accessories VBP-HH1 Hand-held programming device VAZ-PK-1,5M-V1-G Connection cable module/hand-held programming device Subject to reasonable modifications due to technical advances. Copyright Pepperl+Fuchs, Printed in Germany Pepperl+Fuchs Group Tel.: Germany +49 621 776-0 USA +1 330 4253555 Singapore +65 67799091 Internet http://www.pepperl-fuchs.com 205 Masters and Gateways Power Supplies, Extender, Repeaters Safety at work I/O Modules Control cabinet I/O Modules Field application Analogue modules Other modules Inductive sensors Photoelectric sensors Rotary encoders Accessories
Page 1 and 2:
FACTORY AUTOMATION Sensor systems 2
Page 3 and 4:
Issue date 2004-11-19 - Catalogue A
Page 5 and 6:
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150: Issue date 2004-11-19 - Catalogue A
Page 199: Issue date 2004-11-19 - Catalogue A
Page 251 and 252:
Page 253 and 254:
Page 255 and 256:
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Page 263 and 264:
Page 265 and 266:
Page 267 and 268:
Page 269 and 270:
Page 271 and 272:
Page 273 and 274:
Page 275 and 276:
Page 277 and 278:
Page 279 and 280:
Page 281 and 282:
Page 283 and 284:
Page 285 and 286:
Page 287 and 288:
Page 289 and 290:
Page 291 and 292:
Page 293 and 294:
Page 295 and 296:
Page 297 and 298:
Page 299 and 300:
Page 301 and 302:
Page 303 and 304:
Page 305 and 306:
Page 307 and 308:
VAZ-PB-SIM Issue date 2004-11-19 -
Page 309 and 310:
VAZ-R4-R2 Issue date 2004-11-19 - C
Page 311 and 312:
U-G1FA Issue date 2004-11-19 - Cata
Page 313 and 314:
U-G1FFA Issue date 2004-11-19 - Cat
Page 315 and 316:
U-G1PP Issue date 2004-11-19 - Cata
Page 317 and 318:
U-G3FF Issue date 2004-11-19 - Cata
Page 319 and 320:
VAZ-T1-FK-1M-PUR-V1-W Issue date 20
Page 321 and 322:
VAZ-T1-G2F Issue date 2004-11-19 -
Page 323 and 324:
VAZ-T1-FK-M20 Issue date 2004-11-19
Page 325 and 326:
VAZ-V1-B Issue date 2004-11-19 - Ca
Page 327 and 328:
VAZ-TERM Issue date 2004-11-19 - Ca
Page 329 and 330:
Page 331 and 332:
UPR-05 Issue date 2004-11-19 - Cata
Page 333 and 334:
Page 335 and 336:
Page 337 and 338:
Page 339 and 340:
Page 341 and 342:
Page 343 and 344:
Page 345 and 346:
Page 347 and 348:
Page 349 and 350:
Date of issue 2004-19-11 - Catalogu
Page 351 and 352:
Page 353 and 354:
Page 355 and 356:
show all

Sensor systems 2 AS-Interface

Create successful ePaper yourself

Delete template?

Save as template?