MIPS R10000 Microprocessor User's Manual - SGI TechPubs Library

More documents

Recommendations

Info

8 Chapter 1. Edge of Known World External Agent or Cluster Coordinator System Bus: 64-bit data, 8-bit check, 12-bit command System Interface Secondary Cache Ctlr 128-bit refill Instruction Cache 32 Kbytes 2-way Set Associative 16-word blocks Unaligned access Addr Four 32-bit instr. fetch Addr Branch Unit Clocks Up to 4 R10000 Microprocessors may be directly connected. Instruction Decode Register Mapping R10000 Address Queue Integer Queue FP Queue 64 Integer Registers 64 Flt.Pt. Registers 128-bit refill or writeback Data Cache 32 Kbytes 2-way Set Associative 2 Banks 8-word blocks 64-bit load or store Switch Adr.Calc. ALU1 ALU2 Adder Multiplier Figure 1-5 Block Diagram of the R10000 Processor Version 2.0 of January 29, 1997 MIPS R10000 Microprocessor User's Manual TLB 19+way Tag 26+7 Data 128+10 Secondary Cache SC Address Secondary Cache (512 Kbytes to 16 Mbytes) Synchronous Static RAM (4-Mbyte cache requires ten 256Kx18-bit RAM chips)
Introduction to the R10000 Processor 9 Functional Units Primary Instruction Cache (I-cache) Primary Data Cache (D-cache) The five execution pipelines allow overlapped instruction execution by issuing instructions to the following five functional units: • two integer ALUs (ALU1 and ALU2) • the Load/Store unit (address calculate) • the floating-point adder • the floating-point multiplier There are also three “iterative” units to compute more complex results: • Integer multiply and divide operations are performed by an Integer Multiply/Divide execution unit; these instructions are issued to ALU2. ALU2 remains busy for the duration of the divide. • Floating-point divides are performed by the Divide execution unit; these instructions are issued to the floating-point multiplier. • Floating-point square root are performed by the Square-root execution unit; these instructions are issued to the floating-point multiplier. The primary instruction cache has the following characteristics: • it contains 32 Kbytes, organized into 16-word blocks, is 2-way set associative, using a least-recently used (LRU) replacement algorithm • it reads four consecutive instructions per cycle, beginning on any word boundary within a cache block, but cannot fetch across a block boundary. • its instructions are predecoded, its fields are rearranged, and a 4-bit unit select code is appended • it checks parity on each word • it permits non-blocking instruction fetch The primary data cache has the following characteristics: • it has two interleaved arrays (two 16 Kbyte ways) • it contains 32 Kbytes, organized into 8-word blocks, is 2-way set associative, using an LRU replacement algorithm. • it handles 64-bit load/store operations • it handles 128-bit refill or write-back operations • it permits non-blocking loads and stores • it checks parity on each byte MIPS R10000 Microprocessor User's Manual Version 2.0 of January 29, 1997
Page 1 and 2: MIPS R10000 Microprocessor User’s
Page 3 and 4: Acknowledgments This book represent
Page 5 and 6: About This Manual Glossary Stylisti
Page 7 and 8: Table of Contents vii Contents Ackn
Page 9 and 10: Table of Contents ix Superscalar In
Page 11 and 12: Table of Contents xi 3 Interface Si
Page 13 and 14: Table of Contents xiii 5 Secondary
Page 15 and 16: Table of Contents xv SysAD[63:0] Ad
Page 17 and 18: Table of Contents xvii 7 Clock Sign
Page 19 and 20: Table of Contents xix 9 Error Prote
Page 21 and 22: Table of Contents xxi 11 JTAG Inter
Page 23 and 24: Table of Contents xxiii 13 Packagin
Page 25 and 26: Table of Contents xxv Branch on Cop
Page 27 and 28: Table of Contents xxvii 16 Memory M
Page 29 and 30: Table of Contents xxix 18 A Cache T
Page 31 and 32: 1. Introduction to the R10000 Proce
Page 33 and 34: Introduction to the R10000 Processo
Page 37: Introduction to the R10000 Processo
Page 63 and 64: 2. System Configurations The R10000
Page 65 and 66: System Configurations 35 2.2 Multip
Page 67 and 68: 3. Interface Signal Descriptions Th
Page 69 and 70: Interface Signal Descriptions 39 3.
Page 75 and 76: 4. Cache Organization and Coherency
Page 77 and 78: Cache Organization and Coherency 47
Page 89 and 90:
5. Secondary Cache Interface The pr
Page 91 and 92:
Secondary Cache Interface 61 5.2 Se
Page 93 and 94:
Secondary Cache Interface 63 Indexi
Page 95 and 96:
Secondary Cache Interface 65 Errata
Page 97 and 98:
Secondary Cache Interface 67 SCTag(
Page 99 and 100:
Secondary Cache Interface 69 4-Word
Page 101 and 102:
Secondary Cache Interface 71 16 or
Page 103 and 104:
Secondary Cache Interface 73 5.7 Wr
Page 105 and 106:
Secondary Cache Interface 75 8-Word
Page 107 and 108:
Secondary Cache Interface 77 Tag Wr
Page 109 and 110:
6. System Interface Operations The
Page 111 and 112:
System Interface Operations 81 6.4
Page 113 and 114:
Page 115 and 116:
System Interface Operations 85 Mult
Page 117 and 118:
System Interface Operations 87 Exte
Page 119 and 120:
Page 121 and 122:
System Interface Operations 91 Outg
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
System Interface Operations 97 Duri
Page 129 and 130:
System Interface Operations 99 Erra
Page 131 and 132:
System Interface Operations 101 Cyc
Page 133 and 134:
System Interface Operations 103 Sys
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
System Interface Operations 111 Mul
Page 143 and 144:
System Interface Operations 113 Err
Page 145 and 146:
System Interface Operations 115 Pro
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
System Interface Operations 127 Ext
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
Page 173 and 174:
System Interface Operations 143 Coh
Page 175 and 176:
Page 177 and 178:
System Interface Operations 147 The
Page 179 and 180:
System Interface Operations 149 In
Page 181 and 182:
Page 183 and 184:
Page 185 and 186:
7. Clock Signals The R10000 process
Page 187 and 188:
Clock Signals 157 7.2 Secondary Cac
Page 189 and 190:
8. Initialization This section desc
Page 191 and 192:
Initialization 161 Errata Vcc VccQ[
Page 193 and 194:
Initialization 163 8.4 Soft Reset S
Page 195 and 196:
Initialization 165 Table 8-1 (cont.
Page 197 and 198:
9. Error Protection and Handling Th
Page 199 and 200:
Error Protection and Handling 169 9
Page 201 and 202:
Page 203 and 204:
Page 205 and 206:
Page 207 and 208:
Error Protection and Handling 177 D
Page 209 and 210:
Error Protection and Handling 179 T
Page 211 and 212:
Error Protection and Handling 181 E
Page 213 and 214:
Error Protection and Handling 183 W
Page 215 and 216:
Error Protection and Handling 185 P
Page 217 and 218:
10. CACHE Instructions This chapter
Page 219 and 220:
CACHE Instructions 189 TLB Refill a
Page 221 and 222:
CACHE Instructions 191 Op Field Enc
Page 223 and 224:
CACHE Instructions 193 10.4 Index W
Page 225 and 226:
CACHE Instructions 195 10.7 Index L
Page 227 and 228:
CACHE Instructions 197 10.11 Hit In
Page 229 and 230:
CACHE Instructions 199 10.15 Hit Wr
Page 231 and 232:
CACHE Instructions 201 10.17 Index
Page 233 and 234:
11. JTAG Interface Operation Errata
Page 235 and 236:
JTAG Interface Operation 205 11.2 I
Page 237 and 238:
JTAG Interface Operation 207 ‡ Wi
Page 239 and 240:
12. Electrical Specifications This
Page 241 and 242:
Electrical Specifications 211 DCOk
Page 243 and 244:
Electrical Specifications 213 Unuse
Page 245 and 246:
Electrical Specifications 215 12.2
Page 247 and 248:
Electrical Specifications 217 12.3
Page 249 and 250:
13. Packaging The R10000 microproce
Page 251 and 252:
Packaging 221 Electrical Characteri
Page 253 and 254:
Packaging 223 Figure 13-1 R10000 59
Page 255 and 256:
Packaging 225 Table 13-3 (cont.) Si
Page 257 and 258:
Page 259 and 260:
Page 261 and 262:
Packaging 231 Figure 13-3 599LGA PW
Page 263 and 264:
Packaging 233 Figure 13-5 599LGA Bo
Page 265 and 266:
14. Coprocessor 0 This chapter desc
Page 267 and 268:
Coprocessor 0 237 14.1 Index Regist
Page 269 and 270:
Coprocessor 0 239 14.3 EntryLo0 (2)
Page 271 and 272:
Coprocessor 0 241 14.4 Context (4)
Page 273 and 274:
Coprocessor 0 243 14.6 Wired Regist
Page 275 and 276:
Coprocessor 0 245 14.9 EntryHi Regi
Page 277 and 278:
Coprocessor 0 247 CU2 CU2 CU1 CU1 C
Page 279 and 280:
Coprocessor 0 249 Diagnostic Status
Page 281 and 282:
Coprocessor 0 251 Coprocessor Acces
Page 283 and 284:
Coprocessor 0 253 Table 14-13 Cause
Page 285 and 286:
Coprocessor 0 255 14.13 Processor R
Page 287 and 288:
Coprocessor 0 257 14.15 Load Linked
Page 289 and 290:
Coprocessor 0 259 14.17 XContext Re
Page 291 and 292:
Coprocessor 0 261 14.19 Diagnostic
Page 293 and 294:
Coprocessor 0 263 Errata There are
Page 295 and 296:
Coprocessor 0 265 Errata Errata The
Page 297 and 298:
Coprocessor 0 267 Event 1 for Count
Page 299 and 300:
Coprocessor 0 269 Event 6 for Count
Page 301 and 302:
Coprocessor 0 271 Event 14 for Coun
Page 303 and 304:
Coprocessor 0 273 14.21 ECC Registe
Page 305 and 306:
Coprocessor 0 275 CacheErr Register
Page 307 and 308:
Coprocessor 0 277 CacheErr Register
Page 309 and 310:
Coprocessor 0 279 Errata Primary In
Page 311 and 312:
Coprocessor 0 281 Errata Errata Sec
Page 313 and 314:
Coprocessor 0 283 Primary Data Cach
Page 315 and 316:
Coprocessor 0 285 14.25 CP0 Instruc
Page 317 and 318:
Coprocessor 0 287 14.27 CACHE Instr
Page 319 and 320:
Coprocessor 0 289 Cache CACHE (cont
Page 321 and 322:
Coprocessor 0 291 14.29 DMTC0 Instr
Page 323 and 324:
Coprocessor 0 293 14.31 MFC0 Instru
Page 325 and 326:
Coprocessor 0 295 MTPS 31 Format: M
Page 327 and 328:
Coprocessor 0 297 14.34 TLBP Instru
Page 329 and 330:
Coprocessor 0 299 14.36 TLBWI Instr
Page 331 and 332:
15. Floating-Point Unit This sectio
Page 333 and 334:
Floating-Point Unit 303 15.2 Floati
Page 335 and 336:
Floating-Point Unit 305 Load and St
Page 337 and 338:
Floating-Point Unit 307 63 63 Doubl
Page 339 and 340:
Floating-Point Unit 309 Floating-Po
Page 341 and 342:
Floating-Point Unit 311 Loading the
Page 343 and 344:
Floating-Point Unit 313 Moves and C
Page 345 and 346:
16. Memory Management This section
Page 347 and 348:
Memory Management 317 Addressing Mo
Page 349 and 350:
Memory Management 319 32-bit User M
Page 351 and 352:
Memory Management 321 32-bit Superv
Page 353 and 354:
Memory Management 323 32-bit Kernel
Page 355 and 356:
Memory Management 325 0X BFFFFFFF 0
Page 357 and 358:
Memory Management 327 64-bit Virtua
Page 359 and 360:
Memory Management 329 Using the TLB
Page 361 and 362:
17. CPU Exceptions This chapter des
Page 363 and 364:
CPU Exceptions 333 17.3 TLB Refill
Page 365 and 366:
CPU Exceptions 335 Priority of Exce
Page 367 and 368:
CPU Exceptions 337 Soft † Reset E
Page 369 and 370:
CPU Exceptions 339 NMI Exception Ca
Page 371 and 372:
CPU Exceptions 341 TLB Exceptions T
Page 373 and 374:
CPU Exceptions 343 TLB Invalid Exce
Page 375 and 376:
CPU Exceptions 345 Cache Error Exce
Page 377 and 378:
CPU Exceptions 347 Integer Overflow
Page 379 and 380:
CPU Exceptions 349 System Call Exce
Page 381 and 382:
CPU Exceptions 351 Reserved Instruc
Page 383 and 384:
CPU Exceptions 353 Floating-Point E
Page 385 and 386:
CPU Exceptions 355 Interrupt Except
Page 387 and 388:
CPU Exceptions 357 17.5 COP0 Instru
Page 389 and 390:
18. Cache Test Mode The R10000 proc
Page 391 and 392:
Cache Test Mode 361 18.3 Entering C
Page 393 and 394:
Cache Test Mode 363 18.5 SysAD(63:0
Page 395 and 396:
Cache Test Mode 365 Auto-Increment
Page 397 and 398:
Cache Test Mode 367 Auto-Increment
Page 399 and 400:
A. Glossary The following terms are
Page 401 and 402:
A.6 Dynamic Scheduling The R10000 p
Page 403 and 404:
A.11 Nonblocking Loads and Stores M
Page 405 and 406:
A.13 Logical and Physical Registers
Page 407 and 408:
Index I-1 Index Numerics 16-word, c
Page 409 and 410:
Index I-3 uncached accelerated, des
Page 411 and 412:
Index I-5 branch on CP0 instruction
Page 413 and 414:
Index I-7 F fetch pipeline 6, 17 fe
Page 415 and 416:
Index I-9 TLBWR 285, 300 unsupporte
Page 417 and 418:
Index I-11 NMI see also nonmaskable
Page 419 and 420:
Index I-13 CP0 (description of) 235
Page 421 and 422:
Index I-15 SysAD[20:16] interrupt r
Page 423 and 424:
Index I-17 SysWrRdy, signal 41, 118
show all

MIPS R10000 Microprocessor User's Manual - SGI TechPubs Library

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?