LABTOOL-848XP - Advantech Equipment Corp.
LABTOOL-848XP - Advantech Equipment Corp. LABTOOL-848XP - Advantech Equipment Corp.
Verifying a device Menu Device | Verify Hot-key Alt+V Figure 4-4 Programming progress screen This function compares the contents of the active device with the contents of the memory buffer. It will display an error message and the address if it finds an address where the data differs. It will also abort the process when this happens. 26
Memory Protect Figure 4-5 Device verification screen Menu Device | Memory Prot/Prog Config Hot-key Alt+Y This function is a device-specific command; it appears on the main menu only after chips having this capability are selected. The function must be configured before use. When properly configured, it can be selected and will automatically set memory protection on the chips immediately after they have been programmed. Erasing a device Menu Device | Erase Hot-key Alt+K This function is a device-specific command; it appears on the main menu only after electronically erasable chips have been selected. The function can be used to erase a desired memory range from a chip. Configuration Menu Device | Configuration Hot-key Alt+U This function is a device-specific command for a single Flash chip with a software protect block, an option register, configure word and lock bit. The function must be configured before use. When used, 27
- Page 1 and 2: LABTOOL-848XP Turbo Gang Programmer
- Page 3 and 4: How to use this manual Thank you fo
- Page 5 and 6: Contents Chapter 0 Quick Start.....
- Page 7 and 8: CHAPTER Quick Start 0 7
- Page 9 and 10: CHAPTER General Information 1 9
- Page 11 and 12: operator adjustable time. If the op
- Page 13 and 14: Hot Keys Main Menu Sub Menu Device
- Page 15 and 16: Minimum PC System Requirements O.S.
- Page 17 and 18: LABTOOL-848XP Command Hierarchy Fil
- Page 19 and 20: LED Display on Each Socket Each of
- Page 21 and 22: From File Address If only a selecte
- Page 23 and 24: Keyboard Press TAB until the cursor
- Page 25: This button controls the display of
- Page 29 and 30: Figure 4-7 Example screen: Modify a
- Page 31 and 32: When the insertion timer is enabled
- Page 33 and 34: Statistic Commands Figure 4-10 Para
- Page 35 and 36: Self Test Menu Diagnostics | Self T
- Page 37 and 38: Adapter requirements The LABTOOL-84
- Page 39 and 40: Adapter Types Adapter Adapter Decsr
- Page 41 and 42: Error Messages This function is not
- Page 43 and 44: APPENDIX USB Software General Infor
- Page 45 and 46: Multiple Programmers Operation The
Memory Protect<br />
Figure 4-5 Device verification screen<br />
Menu Device | Memory Prot/Prog Config<br />
Hot-key Alt+Y<br />
This function is a device-specific command; it appears on the main menu only after chips having<br />
this capability are selected. The function must be configured before use. When properly configured,<br />
it can be selected and will automatically set memory protection on the chips immediately after they<br />
have been programmed.<br />
Erasing a device<br />
Menu Device | Erase<br />
Hot-key Alt+K<br />
This function is a device-specific command; it appears on the main menu only after electronically<br />
erasable chips have been selected. The function can be used to erase a desired memory range from a<br />
chip.<br />
Configuration<br />
Menu Device | Configuration<br />
Hot-key Alt+U<br />
This function is a device-specific command for a single Flash chip with a software protect block, an<br />
option register, configure word and lock bit. The function must be configured before use. When used,<br />
27