Simulation of electric and magnetic fields using FEMM - FH Aachen ...

More documents

Recommendations

Info

Figure 1-96 Mesh Figure 1-97 Mesh (zoom) 1.6.7 Display results Figure 1-98 Result
1.6.8 Plot field values Draw E and D plot for this module. First choose the contour . Connect the two nodes (0, 0.1) and (0, 40). Figure 1-99 Contour Figure 1-100 X-Y plot of field values dialogue box We choose E,t here because we need electrical field along the red line. Normal field means the field vertical to the line we chose. So is D,t. If you find your curve too rough, you can go back to 1.6.6 to change the mesh size and run the analysis again. The smaller the mesh size is, the finer your curve may get. Figure 1-101E,t plot
Page 1 and 2: Simulation of electric and magnetic
Page 3 and 4: Acknowledgments I would like to exp
Page 5 and 6: 1.4.1 Create a new file. ..........
Page 7 and 8: 3.2.1 Create new file .............
Page 9 and 10: Current flow procedures: 1. Create
Page 11 and 12: Problem Type: Axisymmetric Length U
Page 13 and 14: Figure 1-7 Voltage on layer 1 Groun
Page 15 and 16: 1.1.7 Generate mesh and run FEA Run
Page 17 and 18: Figure 1-18E,t plot And this plot c
Page 19 and 20: 1.2.2 Set problem definition. Press
Page 21 and 22: But here we have a non-symmetric ca
Page 23 and 24: 1.2.6 Define conductor and material
Page 25 and 26: Figure 1-38 Contour Then select E,
Page 27 and 28: 1.3.3 Create a new model We treat t
Page 29 and 30: 1.3.5 Set up the properties of mate
Page 31 and 32: Figure 1-53 Result 1.3.9 Plot field
Page 33 and 34: Inner cable 2*ri=10 mm Flange(Flans
Page 35 and 36: Figure 1-62 Conductor properties Fi
Page 37 and 38: Figure 1-67Contour Use function to
Page 39 and 40: 1.5.2 Set problem definition. Press
Page 41 and 42: 1.5.6 Define conductor properties T
Page 43 and 44: Figure 1-83D,t plot 1.5.11 Comparis
Page 45 and 46: And this time it seems to be smooth
Page 47: The outer shell is connected with g
Page 51 and 52: 1.7.3 Create a new model Draw 3 seg
Page 53 and 54: 1.7.8 Display results Figure 1-111R
Page 55 and 56: 2. Electrical Field Before we deal
Page 57 and 58: 2.1.5 Define conductor properties S
Page 59 and 60: Draw the contour from (0, 0) to (14
Page 61 and 62: Figure 2-13 New model step 2 2.2.4
Page 63 and 64: σr=1 for schicht2 Figure 2-19Prope
Page 65 and 66: 2.2.9 Plot field values Choose cont
Page 67 and 68: Figure 3-2 Problem definition 3.1.3
Page 69 and 70: 3.1.7 Define circuits. Select menu
Page 71 and 72: 3.1.10 Associate Properties with bo
Page 73 and 74: Click on button . Then in the dialo
Page 75 and 76: 3.2 Air gap Here we have a square c
Page 77 and 78: Figure 3-24 Circuit 3.2.8 Place Blo
Page 79 and 80: Figure 3-29 Mesh 3.2.12 Analysis re
Page 81 and 82: 3.2.13 Plot Field Values Draw conto
Page 83 and 84: List of figures Figure 1-1 Create a
Page 85 and 86: Figure 1-89 New model .............
Page 87: List of tables Table 1-1 Values of

Simulation of electric and magnetic fields using FEMM - FH Aachen ...

Create successful ePaper yourself

Delete template?

Save as template?