Simulation of electric and magnetic fields using FEMM - FH Aachen ...

More documents

Recommendations

Info

Figure 1-51 Conductor 2 Figure 1-52 Ground 1.3.6 Place block labels and associate them with corresponding materials Set up block properties, using function “Operate on block labels”. Left click on a closed area to mark the label, then right click on the label and press Space button to call the menu. We set every block between 2 boards to „air‟. (air: εx = εy= 1) 1.3.7 Notice If the program can‟t calculate the mesh, which means the angle is too small to calculate, click on to adjust the minimal angle to 1°. 1.3.8 Generate mesh and run analysis Now save the file and click on the toolbar button with yellow mesh . And the result is shown here.
Figure 1-53 Result 1.3.9 Plot field values Then choose a horizontal contour to draw the electrical field plot for this module. Select plot type “E, t”. Figure 1-54 Result (zoom) Figure 1-55E,t plot From the plot we can see the model is perfect homogenous. And it matches the facts.
Page 1 and 2: Simulation of electric and magnetic
Page 3 and 4: Acknowledgments I would like to exp
Page 5 and 6: 1.4.1 Create a new file. ..........
Page 7 and 8: 3.2.1 Create new file .............
Page 9 and 10: Current flow procedures: 1. Create
Page 11 and 12: Problem Type: Axisymmetric Length U
Page 13 and 14: Figure 1-7 Voltage on layer 1 Groun
Page 15 and 16: 1.1.7 Generate mesh and run FEA Run
Page 17 and 18: Figure 1-18E,t plot And this plot c
Page 19 and 20: 1.2.2 Set problem definition. Press
Page 21 and 22: But here we have a non-symmetric ca
Page 23 and 24: 1.2.6 Define conductor and material
Page 25 and 26: Figure 1-38 Contour Then select E,
Page 27 and 28: 1.3.3 Create a new model We treat t
Page 29: 1.3.5 Set up the properties of mate
Page 33 and 34: Inner cable 2*ri=10 mm Flange(Flans
Page 35 and 36: Figure 1-62 Conductor properties Fi
Page 37 and 38: Figure 1-67Contour Use function to
Page 39 and 40: 1.5.2 Set problem definition. Press
Page 41 and 42: 1.5.6 Define conductor properties T
Page 43 and 44: Figure 1-83D,t plot 1.5.11 Comparis
Page 45 and 46: And this time it seems to be smooth
Page 47 and 48: The outer shell is connected with g
Page 49 and 50: 1.6.8 Plot field values Draw E and
Page 51 and 52: 1.7.3 Create a new model Draw 3 seg
Page 53 and 54: 1.7.8 Display results Figure 1-111R
Page 55 and 56: 2. Electrical Field Before we deal
Page 57 and 58: 2.1.5 Define conductor properties S
Page 59 and 60: Draw the contour from (0, 0) to (14
Page 61 and 62: Figure 2-13 New model step 2 2.2.4
Page 63 and 64: σr=1 for schicht2 Figure 2-19Prope
Page 65 and 66: 2.2.9 Plot field values Choose cont
Page 67 and 68: Figure 3-2 Problem definition 3.1.3
Page 69 and 70: 3.1.7 Define circuits. Select menu
Page 71 and 72: 3.1.10 Associate Properties with bo
Page 73 and 74: Click on button . Then in the dialo
Page 75 and 76: 3.2 Air gap Here we have a square c
Page 77 and 78: Figure 3-24 Circuit 3.2.8 Place Blo
Page 79 and 80: Figure 3-29 Mesh 3.2.12 Analysis re
Page 81 and 82:
3.2.13 Plot Field Values Draw conto
Page 83 and 84:
List of figures Figure 1-1 Create a
Page 85 and 86:
Figure 1-89 New model .............
Page 87:
List of tables Table 1-1 Values of
show all

Simulation of electric and magnetic fields using FEMM - FH Aachen ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?