Simulation of electric and magnetic fields using FEMM - FH Aachen ...

More documents

Recommendations

Info

This Bachelor thesis has been carried out at Fachbereich Energietechnik Aachen University of Applied Sciences Jülich , Germany This thesis was supervised by : Prof. Dr. Alexander Kern Prof. Dr. Christoph Helsper I certify that this work has been carried out and written up entirely by myself. No literature references and resources other than cited have been used. Jülich , Germany , June 2011
Acknowledgments I would like to express my deepest gratitude to Prof. Dr. Alexander Kern, for his expertise, understanding and guidance, thanks for correcting this thesis over and over again. And I also want to thank Prof. Dr. Christoph Helsper for his suggestions and supervision of my project. Also I would like to thank both of my professors, for their great help in the past several years. At the same time, I would like to thank all Professors of FH Aachen who had given me so much advises and help during my study in Germany. And I would like to thank my family and my friends for their deep love and support. Thanks very much.
Page 1: Simulation of electric and magnetic
Page 5 and 6: 1.4.1 Create a new file. ..........
Page 7 and 8: 3.2.1 Create new file .............
Page 9 and 10: Current flow procedures: 1. Create
Page 11 and 12: Problem Type: Axisymmetric Length U
Page 13 and 14: Figure 1-7 Voltage on layer 1 Groun
Page 15 and 16: 1.1.7 Generate mesh and run FEA Run
Page 17 and 18: Figure 1-18E,t plot And this plot c
Page 19 and 20: 1.2.2 Set problem definition. Press
Page 21 and 22: But here we have a non-symmetric ca
Page 23 and 24: 1.2.6 Define conductor and material
Page 25 and 26: Figure 1-38 Contour Then select E,
Page 27 and 28: 1.3.3 Create a new model We treat t
Page 29 and 30: 1.3.5 Set up the properties of mate
Page 31 and 32: Figure 1-53 Result 1.3.9 Plot field
Page 33 and 34: Inner cable 2*ri=10 mm Flange(Flans
Page 35 and 36: Figure 1-62 Conductor properties Fi
Page 37 and 38: Figure 1-67Contour Use function to
Page 39 and 40: 1.5.2 Set problem definition. Press
Page 41 and 42: 1.5.6 Define conductor properties T
Page 43 and 44: Figure 1-83D,t plot 1.5.11 Comparis
Page 45 and 46: And this time it seems to be smooth
Page 47 and 48: The outer shell is connected with g
Page 49 and 50: 1.6.8 Plot field values Draw E and
Page 51 and 52: 1.7.3 Create a new model Draw 3 seg
Page 53 and 54:
1.7.8 Display results Figure 1-111R
Page 55 and 56:
2. Electrical Field Before we deal
Page 57 and 58:
2.1.5 Define conductor properties S
Page 59 and 60:
Draw the contour from (0, 0) to (14
Page 61 and 62:
Figure 2-13 New model step 2 2.2.4
Page 63 and 64:
σr=1 for schicht2 Figure 2-19Prope
Page 65 and 66:
2.2.9 Plot field values Choose cont
Page 67 and 68:
Figure 3-2 Problem definition 3.1.3
Page 69 and 70:
3.1.7 Define circuits. Select menu
Page 71 and 72:
3.1.10 Associate Properties with bo
Page 73 and 74:
Click on button . Then in the dialo
Page 75 and 76:
3.2 Air gap Here we have a square c
Page 77 and 78:
Figure 3-24 Circuit 3.2.8 Place Blo
Page 79 and 80:
Figure 3-29 Mesh 3.2.12 Analysis re
Page 81 and 82:
3.2.13 Plot Field Values Draw conto
Page 83 and 84:
List of figures Figure 1-1 Create a
Page 85 and 86:
Figure 1-89 New model .............
Page 87:
List of tables Table 1-1 Values of
show all

Simulation of electric and magnetic fields using FEMM - FH Aachen ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?