Geon 138 - Excel Polymers
Geon 138 - Excel Polymers Geon 138 - Excel Polymers
TECHNICAL DATA SHEET GEON COPOLYMER DISPERSION RESIN GEON ® 138 4% VINYL ESTER / VINYL CHLORIDE COPOLYMER BENEFITS − Geon ® 138 is a 4% vinyl ester copolymer dispersion resin exhibiting fast fusion at low processing temperatures, resulting in energy savings and the ability to work with heat sensitive substrates − Vinyl ester copolymers exhibit stable Brookfield viscosity aging characteristics − Mechanically and chemically foamable RECOMMENDED USES Geon ® 138 is recommended for applications where low processing temperatures are required, such as: 1. Carpet tile and walk-off mat backings 2. Plastisol inks 3. General low temperature processing applications 4. Automotive sealants TYPICAL PROPERTIES (1) Typical Resin Properties Inherent Viscosity (ASTM-D-1243-60-A) 1.20 Relative Viscosity (Cyclohexanone 1%) 2.71 K-Value 77 Degree of Polymerization 1,750 Methanol Extractables (Geon ® 894) 2.3% % Moisture (Karl Fisher-Geon ® 683) 0.06% Appearance Fine White Powder Bulk Density 20-25 lbs./cu. ft. 0.34 - 0.42 gm/cm Specific Gravity 1.40 Typical Plastisol Properties (2) Initial Brookfield Viscosity - V12 (Geon ® 1010) 2,400 cps One-Day Brookfield Viscosity-V12 (Geon ® 1010) 5,700 cps Severs Efflux - 95 psi (Geon ® 1010) 19.9 gms/100 sec. North Fineness (Geon ® 390) 5.5 Typical Fused Film Properties (3) Gel Temperature (ALTC-29) 144°F 62°C Clarity - Light Transmittance (ALTC-66) 88% Gloss - 60° (ALTC-65) 85% reflectance Optimum Tensile (ASTM-D-638) 2,700 psi 18.6 mPa Elongation at Optimum Tensile (ASTM-D-412) 380% (1) The values set forth represent “typical” values and The Geon Company, therefore, makes no representation that the material in any particular shipment will conform to the listed properties. (2) ® Formulation: 100 parts Geon 138, 60 parts DOP (3) ® Formulation: 100 parts Geon 138, 57 parts DOP, 3 parts epoxy soybean oil, 2 parts Synpron 940 SERVICE VALUE RELIABILITY
TECHNICAL DATA SHEET<br />
GEON COPOLYMER DISPERSION RESIN<br />
GEON ® <strong>138</strong><br />
4% VINYL ESTER / VINYL CHLORIDE COPOLYMER<br />
BENEFITS<br />
− <strong>Geon</strong> ® <strong>138</strong> is a 4% vinyl ester copolymer dispersion resin exhibiting fast fusion at<br />
low processing temperatures, resulting in energy savings and the ability to work<br />
with heat sensitive substrates<br />
− Vinyl ester copolymers exhibit stable Brookfield viscosity aging characteristics<br />
− Mechanically and chemically foamable<br />
RECOMMENDED USES<br />
<strong>Geon</strong> ® <strong>138</strong> is recommended for applications where low processing temperatures are<br />
required, such as:<br />
1. Carpet tile and walk-off mat backings<br />
2. Plastisol inks<br />
3. General low temperature processing applications<br />
4. Automotive sealants<br />
TYPICAL PROPERTIES (1)<br />
Typical Resin Properties<br />
Inherent Viscosity (ASTM-D-1243-60-A) 1.20<br />
Relative Viscosity (Cyclohexanone 1%) 2.71<br />
K-Value 77<br />
Degree of Polymerization 1,750<br />
Methanol Extractables (<strong>Geon</strong> ® 894) 2.3%<br />
% Moisture (Karl Fisher-<strong>Geon</strong> ® 683) 0.06%<br />
Appearance Fine White Powder<br />
Bulk Density 20-25 lbs./cu. ft.<br />
0.34 - 0.42 gm/cm<br />
Specific Gravity 1.40<br />
Typical Plastisol Properties (2)<br />
Initial Brookfield Viscosity - V12 (<strong>Geon</strong> ® 1010) 2,400 cps<br />
One-Day Brookfield Viscosity-V12 (<strong>Geon</strong> ® 1010) 5,700 cps<br />
Severs Efflux - 95 psi (<strong>Geon</strong> ® 1010) 19.9 gms/100 sec.<br />
North Fineness (<strong>Geon</strong> ® 390) 5.5<br />
Typical Fused Film Properties (3)<br />
Gel Temperature (ALTC-29) 144°F<br />
62°C<br />
Clarity - Light Transmittance (ALTC-66) 88%<br />
Gloss - 60° (ALTC-65) 85% reflectance<br />
Optimum Tensile (ASTM-D-638) 2,700 psi<br />
18.6 mPa<br />
Elongation at Optimum Tensile (ASTM-D-412) 380%<br />
(1)<br />
The values set forth represent “typical” values and The <strong>Geon</strong> Company, therefore, makes no<br />
representation that the material in any particular shipment will conform to the listed properties.<br />
(2) ®<br />
Formulation: 100 parts <strong>Geon</strong> <strong>138</strong>, 60 parts DOP<br />
(3) ®<br />
Formulation: 100 parts <strong>Geon</strong> <strong>138</strong>, 57 parts DOP, 3 parts epoxy soybean oil,<br />
2 parts Synpron 940<br />
SERVICE VALUE RELIABILITY
BROOKFIELD VISCOSITY (CPS)<br />
TENSILE STRENGTH (PSI)<br />
8,000<br />
7,000<br />
6,000<br />
5,000<br />
4,000<br />
3,000<br />
2,000<br />
3000<br />
2500<br />
2000<br />
1500<br />
1000<br />
500<br />
2 RPM<br />
BROOKFIELD VISCOSITY AGING CHARACTERISTICS<br />
0 1 2 3 4 5 6 7<br />
FUSION TEMPERATURE VS. TENSILE STRENGTH & ELONGATION<br />
TENSILE<br />
TIME (DAYS)<br />
FORMULATION: 100 PHR RESIN, 57 PHR DOP, 3 PHR ESO, 2 PHR SYNPRON 940<br />
0<br />
0<br />
250 275 300 325 350 375 400<br />
FUSION TEMP (DEG. F)<br />
ELONGATION<br />
20 M IL FILM FUSED 5 M IN . F ORM ULATIO N: 100 PHR RESIN , 57 PHR DOP, 3 PHR ESO, 2 PHR SYNPRON 940<br />
MANUFACTURING<br />
YIELD<br />
20 RPM<br />
<strong>Geon</strong> ® <strong>138</strong> is produced at The <strong>Geon</strong> Company’s Pedricktown, NJ facility, which is ISO 9002 certified.<br />
PACKAGING<br />
Shipped in multi-wall paper bags, net weight 50 pounds, 2,500 pounds per pallet. Information shown on the<br />
package includes commercial identification number, lot number and net weight.<br />
PolyOne © Corporation, 1997<br />
PolyOne © Corporation<br />
The information contained herein is believed to<br />
be reliable, but no representations, guarantees<br />
or warranties of any kind are made as to its<br />
accuracy, suitability for particular applications<br />
or the results to be obtained therefrom. The<br />
information is based on laboratory work with<br />
small-scale equipment and does not<br />
necessarily indicate end product performance.<br />
Because of variations in methods, conditions<br />
and equipment used commercially in<br />
processing these materials, no warranties or<br />
guarantees are made as to suitability of the<br />
products for the application disclosed. Fullscale<br />
testing and end product performance<br />
are the responsibility of the user. PolyOne<br />
shall not be liable for and the customer<br />
assumes all risk and liability of any use or<br />
handling of any material beyond PolyOne's<br />
direct<br />
1.2<br />
1.1<br />
1<br />
0.9<br />
0.8<br />
0.7<br />
0.6<br />
600<br />
500<br />
400<br />
300<br />
200<br />
100<br />
YIELD<br />
control. POLYONE MAKES NO<br />
WARRANTIES, EXPRESS OR IMPLIED,<br />
INCLUDING, BUT NOT LIMITED TO, THE<br />
IMPLIED WARRANTIES OF<br />
MERCHANTABILITY AND FITNESS FOR A<br />
PARTICULAR PURPOSE. Nothing contained<br />
herein is to be considered as permission,<br />
recommendation, nor as an inducement to<br />
practice any patented invention without<br />
permission of the patent owner.<br />
Printed in U.S.A. PolyOne Corporation April, 1997<br />
ELONGATION (%)