2010 Construction and Material Specifications - Ohio Department of ...
2010 Construction and Material Specifications - Ohio Department of ... 2010 Construction and Material Specifications - Ohio Department of ...
732.05 Fit each compartment of pedestrian signal heads with a visor that is at least 7 inches (175 mm) in length or, in lieu of visors, protect the entire face with a sunshade fastened close to the lens. Furnish a black grid sunshade fabricated of high impact resistant plastic with a nominal depth of 1 1/2 inches (38 mm) and consisting of horizontal members spaced at not more than 1/2-inch (13 mm) and vertical members spaced appropriately. Furnish pedestrian signal heads with required mounting brackets. Furnish either pipe type brackets or, when compatible with the mounting position required by the plans, two-piece hinged type brackets that support the signal head close to the pole. Furnish 1 1/2-inch (38 mm) galvanized steel pipe brackets with necessary fittings and adapters, and that are one-way or two-way as required. Orient the signal face to crosswalks by selective meshing of serration rings or other devices provided on housings and mounting brackets. Make adjustment in increments not greater than 5 degrees of rotation and that is not affected by wind gusts when locked. Furnish two-piece hinged brackets of cast aluminum with stainless steel hinge pins, and when closed will be secured by a tamperproof bolt. Ensure that the mounting incorporates a terminal block for quick disconnect of field wiring. Ensure that the mounting design permits attachment to the pole by banding, bolting or by lag screws in the case of wood poles. Paint signal exterior surfaces black with enamel paint. Paint interior surfaces of visors flat black. Furnish pedestrian signal head types according to Table 732.05-1. TABLE 732.05-1 Signal Head Type Symbol Height, Inches, (mm) Light Source A1 6 (152) Clear lamp A2 9 (229) Incandescent, LED D2 9 (229) Clear lamp Incandescent, LED If specified, furnish the types listed below: A. Type A1. Furnish a signal head that utilizes the housings of two 8-inch (200 mm) lens type vehicular traffic sections connected together to form a vertical unit. Ensure that the sections have square lenses. Ensure that the upper lens displays the symbol of an upraised hand in portland orange and the lower lens will display the symbol of a walking person in white . Install a lamp in each section. Furnish materials according to the Department’s Qualified Products List (QPL). B. Type A2. Furnish a signal head that utilizes the housings of two 12-inch (300 mm) lens type vehicular traffic sections connected together to form a vertical unit. Ensure that the sections have square lenses with the same symbol position as Type A1. Install a lamp in each section. 808
809 732.06 Furnish materials according to the Department’s Qualified Products List (QPL). C. Type D2. Furnish a single housing signal head with a lens in one piece or in two sections, one for each message. Color and mask the lens to display in portland orange the symbol of an upraised hand from the left compartment and the symbol of a walking person in white from the right compartment. Furnish reflectors and baffle that form two light compartments. Install a clear glass incandescent lamp in each compartment. When a LED light source is specified, the upraised hand and the walking person symbols may be integral in the same compartment. D. Countdown. 1. Operation. a. Display driver shall be designed to allow individual LED failures without affecting other LEDs in the same display. b. The countdown timer shall be of the “smart” type, which continuously samples the timing intervals presented by the pedestrian signal load switch driver(s) in order to “learn” the programmed timing being used by the controller. c. During interval sampling time, the countdown timer numerical display shall be blank. d. Sampling time to determine interval settings shall take a maximum of two complete signal cycles. e. The unit shall be capable of displaying a countdown commencing at the onset of the pedestrian clearance interval and reaching zero at the end of the pedestrian clearance interval. f. Any interruption of the flashing pedestrian clearance display, e.g., preemption, timing plan change, during a countdown display shall immediately cause blanking of the countdown numerals. The countdown timer shall “re-learn” the pedestrian clearance interval upon return to normal service after preemption or immediately following a change in walk clearance time associated with a timing plan change. 2. Type A2. The top section shall be identical to the 12 inch (300 mm) Type D2 pedestrian signal. The bottom section shall consist of a countdown display in a 12 inch (300 mm) housing. The display numeral segments shall be comprised of two rows of discrete LEDs. 3. Type D2. The left side of the signal section shall consist of an integral hand/walking person display. The right side compartment shall contain the countdown display. The display numeral segments shall be comprised of two rows of discrete LEDs. Furnish materials according to the Department’s Qualified Products List (QPL). 732.06 Pedestrian Pushbuttons. Furnish pushbuttons of sturdy construction that consist of a base housing and a removable cover. Furnish components that provide a pushbutton with normally open contacts and that include all electrical and mechanical parts required for operation.
- Page 763 and 764: 757 711.04 ASTM A 328/A 328M. Furni
- Page 765 and 766: 759 711.13 17 Ship test bars with t
- Page 767 and 768: 761 711.23 18.7.4.5, and 18.10.3. I
- Page 769 and 770: 763 711.27 Air-dry or kiln-dry timb
- Page 771 and 772: Total calcium and magnesium oxides
- Page 773 and 774: Type A: Underdrains and Slope Drain
- Page 775 and 776: 769 712.11 5. A netting weight of a
- Page 777 and 778: 771 712.11 2. Excelsior cut from wo
- Page 779 and 780: 773 721.02 Furnish materials accord
- Page 781 and 782: 775 725.07 725.07 Plastic Pull Boxe
- Page 783 and 784: TABLE 725. 11-3 ANSI WATTS Horizont
- Page 785 and 786: 779 725.11 Ensure that the luminair
- Page 787 and 788: 781 725.15 Ensure that the box and
- Page 789 and 790: 783 725.19 E. Photoelectric Cell. E
- Page 791 and 792: 785 725.21 Luminaires and Traffic S
- Page 793 and 794: 787 725.21 and bears easily found a
- Page 795 and 796: 789 725.21 designed to develop a co
- Page 797 and 798: 730.01 which has been drilled and t
- Page 799 and 800: 793 730.05 730.05 Handhole Covers.
- Page 801 and 802: 795 730.19 730.192 Reflective Sheet
- Page 803 and 804: 797 731.07 60 times per minute with
- Page 805 and 806: Furnish a visor with each signal se
- Page 807 and 808: 801 732.04 percent humidity. Operat
- Page 809 and 810: 803 732.04 q. The module shall be d
- Page 811 and 812: 805 732.04 period of 60 months, ove
- Page 813: 807 732.05 The LED signal lamp unit
- Page 817 and 818: 811 732.08 B. NEMA TS-2. Furnish lo
- Page 819 and 820: 813 732.15 expanding or screw type
- Page 821 and 822: Cable or Wire Number of Conductors
- Page 823 and 824: 817 733.02 1. NEMA 8 phase, dual ri
- Page 825 and 826: 733.03 Model 2070-3B Front Panel, D
- Page 827 and 828: 821 733.03 hardware and equipment f
- Page 829 and 830: 823 733.03 withstand a peak current
- Page 831 and 832: 825 733.03 l. Terminal Blocks. Furn
- Page 833 and 834: 827 733.03 (7) Furnish loop detecto
- Page 835 and 836: 829 733.03 c. Install red monitor c
- Page 837 and 838: light to display. 831 733.03 (c) En
- Page 839 and 840: 733.03 circuits, yellow timing, mul
- Page 841 and 842: 733.03 (h) MULT IND. Illuminates wh
- Page 843 and 844: 837 733.03 Watchdog Timer, 24VDC, C
- Page 845 and 846: (l) Event logs 839 733.03 (5) Furni
- Page 847 and 848: 733.05 A. Cabinet Riser for NEMA Ca
- Page 849 and 850: 843 733.06 b. Time of day/day of we
- Page 851 and 852: 3. Modem 4. Printer 5. Accessory It
- Page 853 and 854: 847 740.01 Furnish two (2) sets of
- Page 855 and 856: 849 740.03 Minimum Maximum 1. Consi
- Page 857 and 858: H. Color. 851 740.05 Minimum Maximu
- Page 859 and 860: 853 740.08 Allow samples to cure at
- Page 861 and 862: 855 748.00 Roundness (Percent by We
- Page 863 and 864: Pipe Diameter Wall Thickness Wall T
732.05<br />
Fit each compartment <strong>of</strong> pedestrian signal heads with a visor that is at least 7<br />
inches (175 mm) in length or, in lieu <strong>of</strong> visors, protect the entire face with a<br />
sunshade fastened close to the lens. Furnish a black grid sunshade fabricated <strong>of</strong><br />
high impact resistant plastic with a nominal depth <strong>of</strong> 1 1/2 inches (38 mm) <strong>and</strong><br />
consisting <strong>of</strong> horizontal members spaced at not more than 1/2-inch (13 mm) <strong>and</strong><br />
vertical members spaced appropriately.<br />
Furnish pedestrian signal heads with required mounting brackets. Furnish either<br />
pipe type brackets or, when compatible with the mounting position required by the<br />
plans, two-piece hinged type brackets that support the signal head close to the<br />
pole.<br />
Furnish 1 1/2-inch (38 mm) galvanized steel pipe brackets with necessary<br />
fittings <strong>and</strong> adapters, <strong>and</strong> that are one-way or two-way as required. Orient the<br />
signal face to crosswalks by selective meshing <strong>of</strong> serration rings or other devices<br />
provided on housings <strong>and</strong> mounting brackets. Make adjustment in increments not<br />
greater than 5 degrees <strong>of</strong> rotation <strong>and</strong> that is not affected by wind gusts when<br />
locked.<br />
Furnish two-piece hinged brackets <strong>of</strong> cast aluminum with stainless steel hinge<br />
pins, <strong>and</strong> when closed will be secured by a tamperpro<strong>of</strong> bolt. Ensure that the<br />
mounting incorporates a terminal block for quick disconnect <strong>of</strong> field wiring.<br />
Ensure that the mounting design permits attachment to the pole by b<strong>and</strong>ing,<br />
bolting or by lag screws in the case <strong>of</strong> wood poles.<br />
Paint signal exterior surfaces black with enamel paint. Paint interior surfaces <strong>of</strong><br />
visors flat black.<br />
Furnish pedestrian signal head types according to Table 732.05-1.<br />
TABLE 732.05-1<br />
Signal Head Type Symbol Height, Inches, (mm) Light Source<br />
A1<br />
6 (152)<br />
Clear lamp<br />
A2<br />
9 (229)<br />
Inc<strong>and</strong>escent, LED<br />
D2 9 (229) Clear lamp<br />
Inc<strong>and</strong>escent, LED<br />
If specified, furnish the types listed below:<br />
A. Type A1. Furnish a signal head that utilizes the housings <strong>of</strong> two 8-inch (200<br />
mm) lens type vehicular traffic sections connected together to form a vertical unit.<br />
Ensure that the sections have square lenses. Ensure that the upper lens displays the<br />
symbol <strong>of</strong> an upraised h<strong>and</strong> in portl<strong>and</strong> orange <strong>and</strong> the lower lens will display the<br />
symbol <strong>of</strong> a walking person in white . Install a lamp in each section.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List<br />
(QPL).<br />
B. Type A2. Furnish a signal head that utilizes the housings <strong>of</strong> two 12-inch<br />
(300 mm) lens type vehicular traffic sections connected together to form a vertical<br />
unit. Ensure that the sections have square lenses with the same symbol position as<br />
Type A1. Install a lamp in each section.<br />
808