2010 Construction and Material Specifications - Ohio Department of ...
2010 Construction and Material Specifications - Ohio Department of ... 2010 Construction and Material Specifications - Ohio Department of ...
725.03 cable and closed securely. Ensure that each tag or band is marked using 1/4 inch (6 mm) minimum height embossed or engraved letters. Ensure that conductors shall be marked "CKT" followed by the circuit designation shown on the plans and that grounding conductors are marked "GND" and that neutral conductors are marked NEU and that hot conductors are marked Line followed by 1" or 2" for single phase power or Phase followed by A or B or C for three phase power. Furnish materials according to the Department’s Qualified Products List (QPL). 725.03 Unit Type Duct-Cable Systems Ensure that factory made cable-induct has conductors as specified, that the duct is high density polyethylene Type III, Class C, Category 5, Grade 34 conforming to NEMA TC-7 and that the duct has the manufacturer's name and the year of manufacture included in the marking. Conductors and neutrals will conform to 725.02. Furnish materials according to the Department’s Qualified Products List (QPL). 725.04 Rigid Galvanized Steel Conduit and Fittings Ensure that rigid galvanized steel conduit complies with the requirements of ANSI C 80.1 and UL 6 Type I and that each length of conduit bears the UL label. Furnish fittings that comply with the requirements of ANSI/NEMA FB 1 AND ANSI/UL 514B. Furnish materials according to the Department’s Qualified Products List (QPL). 725.051 Polyvinyl Chloride Conduits and Fittings. Furnish polyvinyl chloride conduit EPC-40-PVC conforming with NEMA Standard TC 2 for normal above ground or below ground, either concrete encased or direct burial. Use fittings conforming to NEMA Standard TC-2 references. Furnish materials according to the Department’s Qualified Products List (QPL). 725.052 Polyethylene Conduits and Fittings. Furnish polyethylene conduit EPEC-40-HDPE conforming with NEMA Standard TC 7 for below ground only, whether concrete encased or direct burial. Use fittings conforming to ASTM D3350. Furnish materials according to the Department’s Qualified Products List (QPL). 725.06 Polymer Concrete Pull Boxes Ensure that the polymer concrete pull box and cover is of aggregate bound with a polymer resin. Ensure that the body of the box is of one piece construction. Ensure that all surfaces of the box and cover are smooth and that the cover has a molded slip resistant surface. Ensure that the cover is labeled in clearly legible block letters 1 inch to 2 inches (25 mm - 50 mm) in height integral to the cover with the word "TRAFFIC", LIGHTING , "ELECTRIC" or "TELEPHONE to designate the circuit(s) contained. Ensure that the cover closely fits the opening and is secured by stainless steel bolts and hardware and that the threaded holes into which the cover bolts fasten are of open bottom design. Ensure that the box and cover meet the structural requirements of Society of Cable Telecommunications Engineers Tier 15. Furnish materials according to the Department’s Qualified Products List (QPL). 774
775 725.07 725.07 Plastic Pull Boxes Ensure that the plastic pull box and cover is of high density ultraviolet stabilized molded polyethylene with a box wall thickness of at least 1/4 inch (6 mm). The box depth may be obtained through the use of extensions or stacking. Ensure that the cover is slip resistant and has in clearly legible block letters 1 inch to 2 inches (25 mm - 50 mm) in height integral to the cover the word "TRAFFIC”, “LIGHTING”, "ELECTRIC” or "TELEPHONE to designate the circuit(s) contained. Ensure that the cover closely fits the opening and is secured by stainless steel bolts and hardware and that the threaded holes into which the cover bolts fasten are of open bottom design. The box shall meet the structural requirements of Western Underground Committee Guide 3.6. Furnish materials according to the Department’s Qualified Products List (QPL). 725.08 Portland Concrete Pull Boxes. A. Pull Box. Ensure that the Portland concrete pull box is constructed of reinforced portland cement concrete. When the box is precast, provide pull boxes from suppliers certified to Supplement 1073. Ensure that the pull box cover is constructed according to 725.08B and as shown on the plans. B. Pull Box Covers. Furnish metal pull box covers that conform to the following requirements: 1. Furnish 1/2-inch (13 mm) thick steel plate for the steel cover conforming to 711.01 with 1/2-inch (13 mm) minimum flange around the edge and galvanized to conform to 711.02. Display on the steel cover or on an attached brass or stainless steel plate (tag) clearly legible block letters 1 inch to 2 inches (25 mm to 50 mm) in height with the word "TRAFFIC", "LIGHTING", "ELECTRIC" or "TELEPHONE” to designate the circuit(s) contained. Ensure that the word designating the use is in raised letters that are either integral to the steel cover or integral to a brass or stainless steel plate 1/16 inch (1.6 mm) in thickness securely mechanically attached to the steel cover at the four corners of the tag and at intervals 2 inches to 3 inches (50 mm to 75 mm) along the perimeter between corners. 2. Furnish gray iron or ductile iron with a minimum thickness of 3/8 inch (9 mm) conforming to C&MS 711.14. Certification is required. Ensure that the word “TRAFFIC,” "LIGHTING", “ELECTRIC,” or “TELEPHONE” is cast in the top surface of the cover forming letters 1 inch to 2 inches (25 mm to 50 mm) in height. 725.10 Junction Boxes. Ensure that the junction boxes are iron castings hot-dip galvanized in accordance with 711.02. Ensure that the junction boxes meet the requirements of NEMA ICS-6-Type 3. When a drilled and tapped conduit entry is stipulated, ensure that the junction box has adequate wall thickness and that a boss has been cast into the box if such is necessary. Furnish materials according to the Department’s Qualified Products List (QPL). 725.11 Luminaires. A. Optical System. Furnish a luminaire set to the photometric distribution stipulated in the plan and that the distribution along with the settings required to produce it are clearly indicated on a durable label affixed to the interior of the
- Page 729 and 730: 723 706.06 12.0 Make repairs accord
- Page 731 and 732: 725 706.12 Furnish materials accord
- Page 733 and 734: 727 707.01 8.1.2. Ensure that the m
- Page 735 and 736: 729 707.02 annular corrugation that
- Page 737 and 738: 731 707.10 707.10 Square and Rectan
- Page 739 and 740: 733 707.13 9.3 A bell and spigot jo
- Page 741 and 742: 197M. Pipe Pipe-Arch Diameter Wall
- Page 743 and 744: 737 707.25 7.5.1 Reroll the ends of
- Page 745 and 746: 739 707.41 7.4 When tested in accor
- Page 747 and 748: 9.1 Perform inspection at the proje
- Page 749 and 750: 743 708.02 g. Pot life. SSPC-Paint
- Page 751 and 752: 745 708.02 36M hot rolled steel. Bl
- Page 753 and 754: 747 709.01 775, Section 11, permiss
- Page 755 and 756: 749 710.01 in round column and dril
- Page 757 and 758: 751 710.03 TABLE 710.03-1 STEEL POS
- Page 759 and 760: 753 710.03 plunger bar of the latch
- Page 761 and 762: 710.12 Furnish steel line posts acc
- Page 763 and 764: 757 711.04 ASTM A 328/A 328M. Furni
- Page 765 and 766: 759 711.13 17 Ship test bars with t
- Page 767 and 768: 761 711.23 18.7.4.5, and 18.10.3. I
- Page 769 and 770: 763 711.27 Air-dry or kiln-dry timb
- Page 771 and 772: Total calcium and magnesium oxides
- Page 773 and 774: Type A: Underdrains and Slope Drain
- Page 775 and 776: 769 712.11 5. A netting weight of a
- Page 777 and 778: 771 712.11 2. Excelsior cut from wo
- Page 779: 773 721.02 Furnish materials accord
- Page 783 and 784: TABLE 725. 11-3 ANSI WATTS Horizont
- Page 785 and 786: 779 725.11 Ensure that the luminair
- Page 787 and 788: 781 725.15 Ensure that the box and
- Page 789 and 790: 783 725.19 E. Photoelectric Cell. E
- Page 791 and 792: 785 725.21 Luminaires and Traffic S
- Page 793 and 794: 787 725.21 and bears easily found a
- Page 795 and 796: 789 725.21 designed to develop a co
- Page 797 and 798: 730.01 which has been drilled and t
- Page 799 and 800: 793 730.05 730.05 Handhole Covers.
- Page 801 and 802: 795 730.19 730.192 Reflective Sheet
- Page 803 and 804: 797 731.07 60 times per minute with
- Page 805 and 806: Furnish a visor with each signal se
- Page 807 and 808: 801 732.04 percent humidity. Operat
- Page 809 and 810: 803 732.04 q. The module shall be d
- Page 811 and 812: 805 732.04 period of 60 months, ove
- Page 813 and 814: 807 732.05 The LED signal lamp unit
- Page 815 and 816: 809 732.06 Furnish materials accord
- Page 817 and 818: 811 732.08 B. NEMA TS-2. Furnish lo
- Page 819 and 820: 813 732.15 expanding or screw type
- Page 821 and 822: Cable or Wire Number of Conductors
- Page 823 and 824: 817 733.02 1. NEMA 8 phase, dual ri
- Page 825 and 826: 733.03 Model 2070-3B Front Panel, D
- Page 827 and 828: 821 733.03 hardware and equipment f
- Page 829 and 830: 823 733.03 withstand a peak current
725.03<br />
cable <strong>and</strong> closed securely. Ensure that each tag or b<strong>and</strong> is marked using 1/4 inch<br />
(6 mm) minimum height embossed or engraved letters.<br />
Ensure that conductors shall be marked "CKT" followed by the circuit<br />
designation shown on the plans <strong>and</strong> that grounding conductors are marked "GND"<br />
<strong>and</strong> that neutral conductors are marked NEU <strong>and</strong> that hot conductors are marked<br />
Line followed by 1" or 2" for single phase power or Phase followed by A or<br />
B or C for three phase power.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
725.03 Unit Type Duct-Cable Systems Ensure that factory made cable-induct<br />
has conductors as specified, that the duct is high density polyethylene Type<br />
III, Class C, Category 5, Grade 34 conforming to NEMA TC-7 <strong>and</strong> that the duct<br />
has the manufacturer's name <strong>and</strong> the year <strong>of</strong> manufacture included in the marking.<br />
Conductors <strong>and</strong> neutrals will conform to 725.02.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
725.04 Rigid Galvanized Steel Conduit <strong>and</strong> Fittings Ensure that rigid<br />
galvanized steel conduit complies with the requirements <strong>of</strong> ANSI C 80.1 <strong>and</strong> UL 6<br />
Type I <strong>and</strong> that each length <strong>of</strong> conduit bears the UL label. Furnish fittings that<br />
comply with the requirements <strong>of</strong> ANSI/NEMA FB 1 AND ANSI/UL 514B.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
725.051 Polyvinyl Chloride Conduits <strong>and</strong> Fittings. Furnish polyvinyl<br />
chloride conduit EPC-40-PVC conforming with NEMA St<strong>and</strong>ard TC 2 for normal<br />
above ground or below ground, either concrete encased or direct burial. Use<br />
fittings conforming to NEMA St<strong>and</strong>ard TC-2 references.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
725.052 Polyethylene Conduits <strong>and</strong> Fittings. Furnish polyethylene conduit<br />
EPEC-40-HDPE conforming with NEMA St<strong>and</strong>ard TC 7 for below ground only,<br />
whether concrete encased or direct burial. Use fittings conforming to ASTM<br />
D3350.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
725.06 Polymer Concrete Pull Boxes Ensure that the polymer concrete pull<br />
box <strong>and</strong> cover is <strong>of</strong> aggregate bound with a polymer resin. Ensure that the body <strong>of</strong><br />
the box is <strong>of</strong> one piece construction. Ensure that all surfaces <strong>of</strong> the box <strong>and</strong> cover<br />
are smooth <strong>and</strong> that the cover has a molded slip resistant surface. Ensure that the<br />
cover is labeled in clearly legible block letters 1 inch to 2 inches (25 mm - 50 mm)<br />
in height integral to the cover with the word "TRAFFIC", LIGHTING ,<br />
"ELECTRIC" or "TELEPHONE to designate the circuit(s) contained. Ensure that<br />
the cover closely fits the opening <strong>and</strong> is secured by stainless steel bolts <strong>and</strong><br />
hardware <strong>and</strong> that the threaded holes into which the cover bolts fasten are <strong>of</strong> open<br />
bottom design. Ensure that the box <strong>and</strong> cover meet the structural requirements <strong>of</strong><br />
Society <strong>of</strong> Cable Telecommunications Engineers Tier 15.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
774