2010 Construction and Material Specifications - Ohio Department of ...
2010 Construction and Material Specifications - Ohio Department of ... 2010 Construction and Material Specifications - Ohio Department of ...
711.31 Furnish materials according to the Department’s Qualified Products List (QPL). 711.31 Reinforced Propylene Plastic Manhole Steps. Furnish reinforced propylene plastic manhole steps conforming to the details shown on the plans. Furnish steel rod according to 709.01, Grade 60 that is continuous through the entire length of legs and tread. The steel may be coated according to ASTM A 934/A 934M. Ensure that the manufacturer furnishes written certification. Furnish propylene plastic according to ASTM D 4101, Table B 33430. Ensure that the manufacturer furnishes certified test data for the propylene plastic used in each lot of steps. Furnish materials according to the Department’s Qualified Products List (QPL). 712 MISCELLANEOUS 712.01 Expansion Shield Anchors. Furnish anchors conforming to the dimension requirements of the project plans and the following: A. Type A. Federal Specification FF-S-325, Group II, Type 4 Class 1, and Group VIII, Type 1. B. Type B. Federal Specification FF-S-325, Group III, Type 1 (a) or (c). The supplier or producer of the anchors will provide a certification showing certified test results of the proof load required in Federal Specification FF-S-325. Furnish materials according to the Department’s Qualified Products List (QPL). 712.02 Calcium Chloride. Furnish calcium chloride according to ASTM D 98. Furnish materials according to the Department’s Qualified Products List (QPL). 712.03 Sodium Chloride. Furnish sodium chloride according to ASTM D 632, Type I, Grade 1, with the following modification: 4 Total Chlorides (NaCl, CaCl 2, and MgCl 2 as NaCl based on dry weight) not less than 97 percent. 712.04 Lime and Lime Kiln Dust. A. Furnish hydrated lime for masonry purposes according to ASTM C 207, Type S. B. Furnish quick lime for soil stabilization that is certified according to Supplement 1087 and listed on the Department’s Qualified Products List (QPL) and according to ASTM C 977, with the following modification: 4.2.1 Particle size of Quick Lime – Quick lime shall all pass the No. 4 (4.75 mm) sieve. C. Furnish lime kiln dust for soil stabilization that is certified according to Supplemental 1087. Lime kiln dust is a by-product of making lime. Furnish lime kiln dust that meets the following requirements. Perform chemical analysis of the lime kiln dust according to ASTM C 25. 764
Total calcium and magnesium oxides 50 % minimum Total calcium oxides (nonvolatile basis) 50 % minimum Available calcium hydroxide (rapid sugar test) 15 % minimum Loss on ignition (carbon dioxide plus moisture, combined and free on as-received basis) 765 15 % maximum Free water (as-received basis) 2 % maximum Sieve analysis. Sieve Size Minimum Percent Passing No. 4 (4.75 mm) 95 No. 30 (600 µm) 90 No. 100 (150 µm) 75 712.06 Submit test results for the above requirements for every 100 tons (90 metric tons) of lime kiln dust supplied to the Department. If multiple tests were performed, include the average and standard deviation with the results. 712.06 Preservative Treatment for Structural Timber, Lumber, Piling, Posts, Braces, and Blocks. A. General. Furnish structural timber, lumber, and pilings according to 711.26, and posts, braces, and blocks according to 710.14, except that moisture may be removed from the untreated lumber at the time of preservative treatment. Ensure that structural timber, lumber, piling, posts, and braces conform to the current AWPA standards and this subsection. The minimum retention for blocks is 0.40 pounds per cubic foot (6.4 kg/m 3 ). B. Materials. Furnish timber preservatives according to AASHTO M 133. C. Preparation for Treatment. Sort the material into one kind or designated group of kinds of wood and into pieces of approximately equal size and moisture and sapwood content. Separate material to ensure contact of treating medium with all surfaces. D. Framing. Conduct all adzing, boring, chamfering, framing, graining, mortising, and surfacing before treatment. E. Incising. Incise lumber 3 inches (75 mm) or more thick on all four sides. Incise lumber less than 3 inches (75 mm) thick on the wide faces only, except as shown on the plans. Incise Douglas fir with a minimum dimension of 2 inches (50 mm) using a suitable power-driven machine before treatment. Do not incise Douglas fir rails and rail posts. Use the spacing and shape of the cutting teeth and the method of incising necessary to produce a uniform penetration. The minimum required depths of the incisions are as follows:
- Page 719 and 720: 706.05 class. Ensure that the marki
- Page 721 and 722: 706.05 1. All structural design acc
- Page 723 and 724: 717 706.05 handling strengths, then
- Page 725 and 726: 719 706.05 The manufacturer may be
- Page 727 and 728: 721 706.05 The spacing center-to-ce
- Page 729 and 730: 723 706.06 12.0 Make repairs accord
- Page 731 and 732: 725 706.12 Furnish materials accord
- Page 733 and 734: 727 707.01 8.1.2. Ensure that the m
- Page 735 and 736: 729 707.02 annular corrugation that
- Page 737 and 738: 731 707.10 707.10 Square and Rectan
- Page 739 and 740: 733 707.13 9.3 A bell and spigot jo
- Page 741 and 742: 197M. Pipe Pipe-Arch Diameter Wall
- Page 743 and 744: 737 707.25 7.5.1 Reroll the ends of
- Page 745 and 746: 739 707.41 7.4 When tested in accor
- Page 747 and 748: 9.1 Perform inspection at the proje
- Page 749 and 750: 743 708.02 g. Pot life. SSPC-Paint
- Page 751 and 752: 745 708.02 36M hot rolled steel. Bl
- Page 753 and 754: 747 709.01 775, Section 11, permiss
- Page 755 and 756: 749 710.01 in round column and dril
- Page 757 and 758: 751 710.03 TABLE 710.03-1 STEEL POS
- Page 759 and 760: 753 710.03 plunger bar of the latch
- Page 761 and 762: 710.12 Furnish steel line posts acc
- Page 763 and 764: 757 711.04 ASTM A 328/A 328M. Furni
- Page 765 and 766: 759 711.13 17 Ship test bars with t
- Page 767 and 768: 761 711.23 18.7.4.5, and 18.10.3. I
- Page 769: 763 711.27 Air-dry or kiln-dry timb
- Page 773 and 774: Type A: Underdrains and Slope Drain
- Page 775 and 776: 769 712.11 5. A netting weight of a
- Page 777 and 778: 771 712.11 2. Excelsior cut from wo
- Page 779 and 780: 773 721.02 Furnish materials accord
- Page 781 and 782: 775 725.07 725.07 Plastic Pull Boxe
- Page 783 and 784: TABLE 725. 11-3 ANSI WATTS Horizont
- Page 785 and 786: 779 725.11 Ensure that the luminair
- Page 787 and 788: 781 725.15 Ensure that the box and
- Page 789 and 790: 783 725.19 E. Photoelectric Cell. E
- Page 791 and 792: 785 725.21 Luminaires and Traffic S
- Page 793 and 794: 787 725.21 and bears easily found a
- Page 795 and 796: 789 725.21 designed to develop a co
- Page 797 and 798: 730.01 which has been drilled and t
- Page 799 and 800: 793 730.05 730.05 Handhole Covers.
- Page 801 and 802: 795 730.19 730.192 Reflective Sheet
- Page 803 and 804: 797 731.07 60 times per minute with
- Page 805 and 806: Furnish a visor with each signal se
- Page 807 and 808: 801 732.04 percent humidity. Operat
- Page 809 and 810: 803 732.04 q. The module shall be d
- Page 811 and 812: 805 732.04 period of 60 months, ove
- Page 813 and 814: 807 732.05 The LED signal lamp unit
- Page 815 and 816: 809 732.06 Furnish materials accord
- Page 817 and 818: 811 732.08 B. NEMA TS-2. Furnish lo
- Page 819 and 820: 813 732.15 expanding or screw type
711.31<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
711.31 Reinforced Propylene Plastic Manhole Steps. Furnish reinforced<br />
propylene plastic manhole steps conforming to the details shown on the plans.<br />
Furnish steel rod according to 709.01, Grade 60 that is continuous through the<br />
entire length <strong>of</strong> legs <strong>and</strong> tread. The steel may be coated according to ASTM A<br />
934/A 934M. Ensure that the manufacturer furnishes written certification.<br />
Furnish propylene plastic according to ASTM D 4101, Table B 33430. Ensure<br />
that the manufacturer furnishes certified test data for the propylene plastic used in<br />
each lot <strong>of</strong> steps.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
712 MISCELLANEOUS<br />
712.01 Expansion Shield Anchors. Furnish anchors conforming to the<br />
dimension requirements <strong>of</strong> the project plans <strong>and</strong> the following:<br />
A. Type A. Federal Specification FF-S-325, Group II, Type 4 Class 1, <strong>and</strong><br />
Group VIII, Type 1.<br />
B. Type B. Federal Specification FF-S-325, Group III, Type 1 (a) or (c).<br />
The supplier or producer <strong>of</strong> the anchors will provide a certification showing<br />
certified test results <strong>of</strong> the pro<strong>of</strong> load required in Federal Specification FF-S-325.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
712.02 Calcium Chloride. Furnish calcium chloride according to ASTM D<br />
98.<br />
Furnish materials according to the <strong>Department</strong>’s Qualified Products List (QPL).<br />
712.03 Sodium Chloride. Furnish sodium chloride according to ASTM D<br />
632, Type I, Grade 1, with the following modification:<br />
4 Total Chlorides (NaCl, CaCl 2, <strong>and</strong> MgCl 2 as NaCl based on dry weight)<br />
not less than 97 percent.<br />
712.04 Lime <strong>and</strong> Lime Kiln Dust.<br />
A. Furnish hydrated lime for masonry purposes according to ASTM C 207,<br />
Type S.<br />
B. Furnish quick lime for soil stabilization that is certified according to<br />
Supplement 1087 <strong>and</strong> listed on the <strong>Department</strong>’s Qualified Products List (QPL)<br />
<strong>and</strong> according to ASTM C 977, with the following modification:<br />
4.2.1 Particle size <strong>of</strong> Quick Lime – Quick lime shall all pass the No. 4 (4.75<br />
mm) sieve.<br />
C. Furnish lime kiln dust for soil stabilization that is certified according to<br />
Supplemental 1087. Lime kiln dust is a by-product <strong>of</strong> making lime. Furnish lime<br />
kiln dust that meets the following requirements. Perform chemical analysis <strong>of</strong> the<br />
lime kiln dust according to ASTM C 25.<br />
764