2010 Construction and Material Specifications - Ohio Department of ...

631
700.00
Spec No. Material Material only Inspection or Sampling
Requirements
Post Inspection Instructions
515.15 Prestressed Concrete Verify company and brand name of material is For Precast beams delivered on
Bridge Members - on QPL at the time of use. Document in CMS TE-24, verification performed by
Corrosion Inhibitors (Trns.port SiteManager ).
OMM.
526 Approach Slabs Make 6"x12" cylinders for each day, each 200 Within 24 to 48 hours after
yd³. Document in CMS (Trns.port SiteManager sampling, ship cylinders to
). Make two beams if testing before 7 days. Laboratory with required
Field or Standard Cure according to
ACI/ODOT specifications.
documentation.
601.12 Tied Concrete Block Verify company and brand name of material is Notify District Testing if rejecting
Mats
on QPL at the time of use. Ensure proper type material.
(Slope/Channel and inspect material for condition.
If material non-performs or looks
Protection) Document in CMS (Trns.port SiteManager ). defective during use submit a
representative qty of defective
material to the Laboratory.
603.02 External Sealing Verify company and brand name of material is Notify District Testing if rejecting
Bands Joint Wrap on QPL at the time of use. Inspect material for material.
condition.
If material non-performs or looks
609.02 Curbing, Concrete
Document in CMS (Trns.port SiteManager ). defective during use submit a
representative qty of defective
material to the OMM.
Contact District Testing and OMM Aggregate
Medians, and Traffic Section to assure stone curb conforms to
Islands - Stone
Curbs
requirements of 609.02
610 Cellular Retaining 610.04.A Cellular Products will be supplied by Notify District Testing if rejecting
Walls
a source on the Certified Lists for S-1073 material.
maintained by OMM.
If material non-performs or looks
Received with TE-24.
defective during use notify District
Check dimension, condition and compliance
with approved drawings.
610.04.B Cellular Products accept by certified
test data documentation at the Project .
Document in CMS (Trns.port SiteManager ).
Testing and OMM.
613 Low Strength Mortar
Backfill
632.11 Traffic Signal
Equipment
Loop Detector
Sealant
633 Traffic Signal
Controllers
653.02
Supplier to perform trial batches of 1 cy to
ensure flowable consistency and yield.
Refer to Item 613.05 for alternate mix design.
Alternate mix designs will be submitted for
approval 30 days prior to placement.. Submit
written permission form to EPA 10 days prior
to placement.
Notify District Testing if rejecting
material.
If material non-performs or looks
defective during use notify District
Testing and OMM.
Verify manufacturer is on QPL.
Notify District Testing if rejecting
Inspect for condition, appearance and package material.
markings.
If material non-performs or looks
Document in CMS (Trns.port SiteManager ). defective during use notify District
Testing and OMM.
Inspect material for condition and conformance Notify District Testing if rejecting
to shop drawings.
material.
Manufacturer’s certified test data required for
acceptance.
Refer to Handbook of Procedures for
Contractor Certification of Lighting, Signing &
Traffic Signal Working Drawings on OMM
Manual website.
Topsoil Obtain one (1) pint sample of material from
each source and/or stockpile of visually
different material from same source.
Use friction top, air tight metal container
supplied by the Department.
Submit to Office of Geotechnical Engineering
Operations.
Samples will include a TE-31 form or CMS
(Trns.port SiteManager ) print screen
657.02 RipRap for Tree
Protection
Confirm with DET that the aggregate source
has a acceptable performance history. For
sources with poor performance require test data
conforming to ASTM D5240