3U CompactPCI®/Express Core™ 2 Duo SBC - The Simon Group

Recommendations

Info

Industrial Communication 0 MEN 3U CompactPCI and CompactPCI Express F211 – 3U CompactPCI ® Quad Fast Ethernet Interface ■ HP -bit/ -MHz CompactPCI ® ■ full-duplex or half-duplex channels ■ 10Base-T and 100Base-TX physical layer ■ Fully integrated to comply with IEEE80 . u ■ 1 00 V isolation voltage ■ - 0 to +8 °C qualified Ethernet Interfaces ■ Four 10/100Base-TX interfaces ■ Four Micrel KSZ8841 controllers ■ IEEE802.3x support ■ Full-duplex flow control ■ Half-duplex back pressure collision flow control ■ Internal 8KB RX/TX FIFO buffers ■ Auto-negotiation and auto MDIX crossover ■ LinkMD ® cable diagnostics to determine cable length, cable faults and distance to fault ■ Media Access Control (MAC) addresses stored in on-board serial EEPROMs ■ 4x2 status LEDs to signal link status, activity, speed and collision Front Connections ■ Four standard 8-pin RJ45 receptacle connectors CompactPCI ® Bus ■ Compliance with CompactPCI ® Core Specification PICMG 2.0 R3.0 ■ Peripheral slot ■ 32-bit/33-MHz PCI-to-PCI bridge ■ V(I/O): +3.3V or +5V (Universal Board) Electrical Specifications ■ Isolation voltage: 1000V between Ethernet links and 1500V between Ethernet links and shield or ground ■ Supply voltage/power consumption: ■ +3.3V (-3%/+5%), 1A max. ■ MTBF: 875,481h @ 40°C according to IEC/ TR 62380 (RDF 2000) Mechanical Specifications ■ Dimensions: conforming to CompactPCI ® specification for 3U boards ■ Weight: 115g (standard version) Environmental Specifications ■ Temperature range (operation): ■ -40..+85°C (qualified components) ■ Airflow: min. 10m³/h ■ Temperature range (storage): -40..+85°C ■ Relative humidity (operation): max. 95% non-condensing Isolation RJ45/ D-Sub RJ45/ D-Sub RJ45/ D-Sub RJ45/ D-Sub EEPROM EEPROM EEPROM EEPROM 10/100Base-T Ethernet Controller 10/100Base-T Ethernet Controller 10/100Base-T Ethernet Controller 10/100Base-T Ethernet Controller ■ Relative humidity (storage): max. 95% non-condensing ■ Altitude: -300m to + 3,000m ■ Shock: 15g/11ms ■ Bump: 10g/16ms ■ Vibration (sinusoidal): 2g/10..150Hz ■ Conformal coating on request Safety ■ PCB manufactured with a flammability rating of 94V-0 by UL recognized manufacturers EMC ■ Tested according to EN 55022 (radio disturbance), IEC1000-4-2 (ESD) and IEC1000-4-4 (burst) with regard to CE conformity Software Support ■ Drivers for Windows ® , Linux and VxWorks ® from Micrel ■ Driver for QNX ® from QNX ® (in preparation) PCI PCI-to-PCI Bridge PCI CompactPCI® J1
F210 – 3U CompactPCI ® GSM/GPS/UART Interface ■ HP -bit/ -MHz CompactPCI ® ■ GSM-R (Rail) EGSM 00 / GSM 1800 ■ GPS according to NMEA 018 ■ GPS and GSM optically isolated from other functions ■ UARTs via SA-Adapters ■ FPGA for further user-defined functions ■ Reverse SMA connectors to external antennae ■ Extended temperature ranges ■ Conformal coating GSM-R Interface ■ GSM-Rail: Global System for Mobile Communications - Railway ■ Frequency bands ■ EGSM 900, GSM 1800 ■ Compliant to GSM Phase 2/2+ ■ GSM class: Small MS ■ Transmit power: ■ Class 4 (2W) at EGSM 900 ■ Class 1 (1W) at GSM 1800 ■ GPRS connectivity ■ GPRS multi-slot class 10 ■ GPRS mobile station class B ■ Data Services ■ GPRS data downlink transfer: max. 85.6 kbits/s ■ GPRS data uplink transfer: max. 42.8 kbits/s ■ Support of PAP (Password Authentication Protocol) and CHAP (Challenge Handshake Authentication Protocol) for PPP connections ■ Support of PBCCH (Packet Switched Broadcast Control Channel) for enhanced GPRS performance ■ CSD transmission rates: 2.4, 4.8, 9.6, 14.4 kbits/s, non-transparent, V.110 ■ WAP compliant ■ Internet services: TCP, UDP, HTTP, FTP, SMTP, POP3 ■ SMS ■ MT, MO, CB, Text and PDU mode ■ SMS storage: SIM card plus 25 SMS locations in the mobile equipment ■ Transmission of SMS alternatively over CSD or GPRS (user-defined) ■ MMS compliant ■ Fax: Group 3, Class 2 ■ On-board SIM card interface ■ Supported SIM card: 3V ■ Coding scheme CS 1, 2, 3, 4 ■ Optical isolation: 1kV DC ■ One antenna connector at front panel ■ For the use of an external antenna ■ Rugged screw connection ■ Please note that MEN does not offer SIM cards or mobile telephony contracts! GPS Interface ■ 20-parallel-channel GPS (Global Positioning System) receiver ■ GPS Band/Code: L1 frequency, C/A code ■ Integrated TCXO, RTC ■ Horizontal accuracy: better than 2.1m (CEP) 5.2m 2dRMS ■ Time To First Fix (TTFF): ■ Cold start: 34s typ. ■ Warm start: 32s typ. ■ Hot start: 0.5s typ. ■ Sensitivity: ■ Acquisition: -155dBm ■ Navigation: -157dBm ■ Tracking: -159dBm ■ GPS modes ■ TricklePower mode for power saving ■ Push-To-Fix mode ■ Protocol: NMEA 0183 ■ SiRF ® binary messages: altitude, longitude, elevation, velocity, heading, time, satellite tracking status, command/control messages ■ SiRF ® binary interface: raw data ■ Antenna voltage supervision ■ 3GPP compliance ■ Optical isolation: 1kV DC ■ One antenna connector at front panel ■ For the use of an external active antenna ■ Rugged screw connection UARTs ■ Two channels ■ Accessible via on-board connectors ■ Physical interface at front panel using SA-Adapters ■ Two SA-Adapters can be directly plugged within 4HP ■ Different physical layers depending on SA-Adapter: RS232, RS422, RS485 with or without optical isolation ■ SA-Adapters to be ordered separately ■ Data rates up to 2 Mbits/s ■ 60-byte transmit/receive buffer ■ Handshake lines: full support; lines depend on SA-Adapters F B Front panel 4 HP Antenna F Antenna Front connector On-board connector SA SA-Adapter Options Second front panel (+ 4 HP) F F GSM-R Controller GPS Controller F SA B F F F SA SA SA SA B B MEN 3U CompactPCI and CompactPCI Express Front Connections ■ Two Reverse SMA antenna connectors ■ Two cut-outs for SA-Adapters FPGA ■ Standard factory FPGA configuration: ■ Main bus interface ■ 16Z057_UART - UART controller (controls in-system GSM-R/GPS communication and UARTs) ■ 16Z045_FLASH - Flash interface ■ The FPGA offers the possibility to add customized I/O functionality. See FPGA. CompactPCI ® Bus ■ Compliance with CompactPCI ® Core Specification PICMG 2.0 R3.0 ■ Peripheral slot ■ 32-bit/33-MHz PCI-to-PCI bridge ■ V(I/O): +3.3V Electrical Specifications ■ Supply voltage/power consumption: ■ Depends on mounted SA-Adapters and used functions ■ +5V (-3%/+5%), 1900mA max. ■ +3.3V (-3%/+5%), 850mA max. ■ MTBF: 194,570h @ 40°C according to IEC/TR 62380 (RDF 2000) Mechanical Specifications ■ Dimensions: conforming to CompactPCI ® specification for 3U boards ■ Front panel: ■ 4HP with ejector ■ 3U single-slot front panel for two antennae and up to two UART connectors ■ Weight: 170g Isolation UART TTL UART TTL User-defined User-defined User-defined FPGA SDRAM (option) CompactPCI® J1 Industrial Communication 1
Page 1 and 2: Embedded Solutions 3U CompactPCI®
Page 3 and 4: Contents 4 Intel ® -based 3U Compa
Page 5 and 6: F18 - 3U CompactPCI ® /Express Cor
Page 9 and 10: F600 - 3U CompactPCI ® Side Card f
Page 11 and 12: F603 - 3U CompactPCI ® Side Card U
Page 13 and 14: F11N - 3U CompactPCI ® /PXI Penti
Page 15 and 16: F13 - 3U CompactPCI ® MPC8540 SBC
Page 17 and 18: F206N - 3U CompactPCI ® Nios ® II
Page 19: F301 - 3U CompactPCI ® 9-Port Ethe
Page 23 and 24: F206 - 3U CompactPCI ® Octal UART
Page 25 and 26: F212 - 3U CompactPCI ® PCIe MiniCa
Page 27 and 28: F205/F204 - 3U CompactPCI ® /PXI
Page 29 and 30: Individual Solutions 4U 84HP Compac
Page 31 and 32: Standard CompactPCI ® Desktop - 3
Page 35 and 36: CompactPCI ® Express Rack 0701-004

3U CompactPCI®/Express Core™ 2 Duo SBC - The Simon Group

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?