HANDBOOK REQUIREMENTS - Central Maine Power Company

More documents

Recommendations

Info

93 93 1104. HARMONIC LOADS Equipment that draws current with a high harmonic content can have a serious impact on the quality of the <strong>Company</strong>'s service. The <strong>Company</strong> requires that any service comply with the maximum harmonic current distortion limits given in IEEE Standard 519-1992. Table 10.3 of that standard provides the limits for individual harmonic distortion and Total Demand Distortion as a percent of maximum demand load current. A maximum Total Demand Distortion of 5% is generally required at the point of common coupling as defined in IEEE Standard 519- 1992. Examples of equipment that draw high harmonic content current include variable speed and variable frequency drives, computer power supplies, electronic lighting ballasts and rectifiers.
Page 1:
HANDBOOK OF REQUIREMENTS FOR ELECTR
Page 4 and 5:
To contact us for information or as
Page 6 and 7:
CENTRAL MAINE POWER TOWNS SERVED TO
Page 8 and 9:
TABLE OF CONTENTS I. INTRODUCTION 1
Page 10 and 11:
501. Conductor Identification 502.
Page 12 and 13:
XI. UTILIZATION EQUIPMENT SPECIFICA
Page 14:
25. [364-9 & 364-10] Large 9’ x 9
Page 17 and 18:
2 102. REVISIONS OF REQUIREMENTS Th
Page 19 and 20:
4 II. General Requirements 200. APP
Page 21 and 22:
6 Dwelling Application is used when
Page 23 and 24:
8 be any duty or obligation on the
Page 25 and 26:
10 214. CUSTOMER'S RESPONSIBILITY 1
Page 27 and 28:
12 be provided with suitable automa
Page 29 and 30:
14 219. CUSTOMER CONSTRUCTED/OWNED
Page 31 and 32:
16 16 • Provide the Company a pla
Page 33 and 34:
18 III. STANDARD CHARACTERISTICS 30
Page 35 and 36:
20 20 service (whenever possible) f
Page 37 and 38:
22 22 304. TRANSFORMER VAULTS AND M
Page 39 and 40:
24 recommended to provide adequate
Page 41 and 42:
26 Refer to paragraph 219 for the r
Page 43 and 44:
28 Company requirements. Following
Page 45 and 46:
30 conductor to the neutral. Meteri
Page 47 and 48:
32 ith outlets used as mobile home
Page 49 and 50:
34 34 protection shall be installed
Page 51 and 52:
36 36 conductors must extend at lea
Page 53 and 54:
38 505. SERVICE MAST CONSTRUCTION U
Page 55 and 56:
40 40 of sufficient size to readily
Page 57 and 58: 42 42 double-throw switch or other
Page 59 and 60: 44 VII. GROUNDING AND BONDING 700.
Page 61 and 62: 46 2. Metal frame of building or st
Page 63 and 64: 48 electrode/conductor or metallic
Page 65 and 66: 50 building or structure grounding
Page 67 and 68: 52 test switches and control cable
Page 69 and 70: 54 54 804. POLE MOUNTED METERS Pole
Page 71 and 72: 56 56 identify the area served by e
Page 73 and 74: 58 58 “connected to the grounded
Page 75 and 76: 60 by-pass requirements and the res
Page 77 and 78: 62 Meter mounting devices shall be
Page 79 and 80: 64 64 not to interfere with the ope
Page 81 and 82: 66 66 The mounting of Company meter
Page 83 and 84: 68 68 901. CUSTOMER RESPONSIBILITY
Page 85 and 86: 70 acceptable to mount the riser(s)
Page 87 and 88: 72 72 The Company will make all con
Page 89 and 90: 74 other distribution system exists
Page 91 and 92: 76 76 In cases not meeting the prec
Page 93 and 94: 78 78 Primary service requiring hig
Page 95 and 96: 80 80 Section 321 B. During back-fi
Page 97 and 98: 82 82 Customers electing to install
Page 99 and 100: 84 84 determined (in consultation w
Page 101 and 102: 86 service only if it is built to C
Page 103 and 104: 88 X. SERVICE FROM UNDERGROUND MAIN
Page 105 and 106: 90 XI. UTILIZATION EQUIPMENT SPECIF
Page 107: 92 B. Overload protective devices s
show all

HANDBOOK REQUIREMENTS - Central Maine Power Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?