Service Guide 2009 - Club Piscine

More documents

Recommendations

Info

TREADMILLS USING COMMUTATOR CLEANER STONE Bremshey & Tunturi Models 1. Remove power from tread. Take off motor cover and remove brush port cover. 2. Remove brush retainer spring clip and slide brush out of slide. 3. Insert commutator stone and press against copper commutator. 4. Rotate motor by hand while pressing stone end against commutator. Move it back and forth to clean all the area the brush touches. Only needs to be done on one side. 5. Replace brushes. Make sure the brush clips are seated firmly. Re-install brush port covers.
BREMSHEY TREADMILLS CHANGING FROM MILES TO KM Scout Model 1. During the power ON position (initial mode), first Hold the ENTER /SELECT button then press and hold the SPEED + button together to enter the <strong>Service</strong> Menu. 2. Incline window shows model number, distance window the software version, kcal window the year, time window the date, speed window the diameter of roller. 3. Press ENTER / SELECT - the window shows LDU version and ISP version 4. Press ENTER / SELECT to enter KM/MILE switch mode, Press SPEED + - or INCLINE + - to select KM or MILE. The “+” button will give you KM and a “1” in the window, the “-“ button will give you Miles and a “0” in the window. The console then flashes a quick series of numbers as it changes to your selection. Easiest way to check which you are in is to look at starting speed = 0.5 for Miles, 0.8 for Km. 5. Press ENTER / SELECT – the window shows total distance. 6. Press ENTER / SELECT – the window shows total hour. 7. Press ENTER / SELECT – the console goes back to initial mode.
Page 1 and 2: Service Guide 2009
Page 3 and 4: Pliant Delta and Sigma Bremshey Pat
Page 5 and 6: Press „START‟ to test lower boa
Page 7 and 8: Magnet missing from the front rolle
Page 9 and 10: VER. 1.00 TREADLINE Control Trail P
Page 11 and 12: SERVICE MANUAL VERSION 1.00 - 2 - C
Page 13 and 14: 4. Press ‘ENTER’ to show ISP ve
Page 15 and 16: SERVICE MANUAL VERSION 1.00 Lift mo
Page 17 and 18: E7 Instruction in the owner's manua
Page 19 and 20: Speed .............................
Page 21 and 22: VER. 0.30 Service Manual Tunturi T1
Page 23 and 24: SERVICE MANUAL VERSION 0.30 1 FOREW
Page 25 and 26: SERVICE MANUAL VERSION 0.30 5. Pres
Page 27 and 28: 8 % 810 ± 30 9 % 940 ± 30 10 % 10
Page 29 and 30: E7 Instruction in the owner's manua
Page 31 and 32: SERVICE MANUAL VERSION 0.30 The T10
Page 33 and 34: If the potentiometer has lost its p
Page 35: TREADMILLS BELT AND DECK REPLACEMEN
Page 39 and 40: BREMSHEY TREADMILLS TESTING & 10 MO
Page 41 and 42: What Creates Static Shock On Treadm
Page 45 and 46: Rear Drive Ellipticals
Page 47 and 48: • Power machine up (If no power r
Page 49 and 50: To access the internal components o
Page 51 and 52: Resistance Mechanisms There are 3 t
Page 53 and 54: Servo Motor Resistance Control The
Page 55 and 56: complains that either of these sett
Page 58 and 59: ( l ) Section 3 Flywheel & Transmis
Page 60 and 61: h . 3. Before replacing the belt en
Page 62 and 63: Type 2 transmission 1. Slacken off
Page 64: 4. Separating drum cover and cross
Page 67 and 68: The resistance flywheel rotates on
Page 69 and 70: Section 4 Bearings and joints The l
Page 71 and 72: within the area between each bush (
Page 73: ELLIPTICALS CRANK PULLER MODIFICATI
Page 76 and 77: Technical product matrix Console 20
Page 78 and 79: 1. TUNTURI T-GEN (40-85) Brake cali
Page 80 and 81: 1. TUNTURI T-GEN (40-85) •DC volt
Page 82 and 83: 1. TUNTURI T-GEN (40-85) Error code
Page 84 and 85: 2. 3. Technical specification •Sw
Page 86 and 87:
2. 3. Error codes E-2 •Data conne
Page 88 and 89:
VER. 0.90 Tunturi F30, E40, E45, E6
Page 90 and 91:
SERVICE MANUAL VERSION 0.90 F30 E30
Page 92 and 93:
3 ELECTRONICS SERVICE MANUAL VERSIO
Page 94 and 95:
4 UPDATING SOFTWARE SERVICE MANUAL
Page 96 and 97:
5 CALIBRATION SERVICE MANUAL VERSIO
Page 98 and 99:
SERVICE MANUAL VERSION 0.90 F30 E30
Page 100:
7 APPENDICES TROUBLESHOOTING SERVIC
show all

Service Guide 2009 - Club Piscine

Create successful ePaper yourself

Delete template?

Save as template?