Service Guide 2009 - Club Piscine

More documents

Recommendations

Info

4 APPENDICES SERVICE MANUAL VERSION 0.30 1. LOWER BOARD AND CONNECTOR LOCATIONS Figure 5 Lower board connectors and components 2. TECHNICAL DATA T10 Length (storage position) ............... 185 cm (83 cm) Height (storage position) ................ 133 cm (175 cm) Width ............................................. 88 cm Weight ........................................... 94 kg Running surface ............................ 47 x 133 cm Speed ............................................. 0.8-16.0 km/h Elevation range ............................. 0-12 % Motor.............................................. 2.0 HP T20 & T30 Length (storage position) ............... 190 cm (82 cm) Height (storage position) ................ 144 cm (186 cm) Width ............................................. 86 cm Weight ........................................... 99 kg Running surface ............................ 51 x 141 cm Speed ............................................. 0.8-20.0 km/h Elevation range ............................. 0-12 % Motor.............................................. 2.0 HP - 9 -
SERVICE MANUAL VERSION 0.30 The T10 treadmill meets the requirements of the EU’s EMC Directives on electromagnetic compatibility (89/336/EEC) and electrical equipment designed for use within certain voltage limits (73/23/EEC). This product therefore carries the CE label. The T10, T20 and T30 treadmills meet EN precision and safety standards (EN-957). Due to our continuous policy of product development, Tunturi reserves the right to change specifications without notice. 3. TROUBLESHOOTING • Treadmill is making knocking noise - he best way to start finding the root cause of the problem is to listen to the frequence of the noise. For example, the running belt seam overlaps a roller twice per revolution, should this be the frequency of the noise, the belt needs to be adjusted or replaced. If the noise has significantly higher frequency it is likely to be caused by a damaged front or rear roller bearing. - Adjust the rear foot to make the treadmill deck even with the floor • Heart rate readings are inaccurate - The motor wires needs to be wrapped through a ferrite ring and twisted around each other in order to prevent possible heart rate reading interference - Home appliances, e.g. TV and mobile phone, and electric network can generate interference. Try using equipment in different environment • Circuit breaker (6A) trips repeatedly - Check that the treadmill is running mechanically free - Check belt lubrication - If the wall outlet voltage is lower than normal the required current is higher and might cause the breaker to trip 4. SPARE PART DIAGRAMS Please refer to the next page. - 10 -
Page 1 and 2: Service Guide 2009
Page 3 and 4: Pliant Delta and Sigma Bremshey Pat
Page 5 and 6: Press „START‟ to test lower boa
Page 7 and 8: Magnet missing from the front rolle
Page 9 and 10: VER. 1.00 TREADLINE Control Trail P
Page 11 and 12: SERVICE MANUAL VERSION 1.00 - 2 - C
Page 13 and 14: 4. Press ‘ENTER’ to show ISP ve
Page 15 and 16: SERVICE MANUAL VERSION 1.00 Lift mo
Page 17 and 18: E7 Instruction in the owner's manua
Page 19 and 20: Speed .............................
Page 21 and 22: VER. 0.30 Service Manual Tunturi T1
Page 23 and 24: SERVICE MANUAL VERSION 0.30 1 FOREW
Page 25 and 26: SERVICE MANUAL VERSION 0.30 5. Pres
Page 27 and 28: 8 % 810 ± 30 9 % 940 ± 30 10 % 10
Page 29: E7 Instruction in the owner's manua
Page 33 and 34: If the potentiometer has lost its p
Page 35 and 36: TREADMILLS BELT AND DECK REPLACEMEN
Page 37 and 38: BREMSHEY TREADMILLS CHANGING FROM M
Page 39 and 40: BREMSHEY TREADMILLS TESTING & 10 MO
Page 41 and 42: What Creates Static Shock On Treadm
Page 45 and 46: Rear Drive Ellipticals
Page 47 and 48: • Power machine up (If no power r
Page 49 and 50: To access the internal components o
Page 51 and 52: Resistance Mechanisms There are 3 t
Page 53 and 54: Servo Motor Resistance Control The
Page 55 and 56: complains that either of these sett
Page 58 and 59: ( l ) Section 3 Flywheel & Transmis
Page 60 and 61: h . 3. Before replacing the belt en
Page 62 and 63: Type 2 transmission 1. Slacken off
Page 64: 4. Separating drum cover and cross
Page 67 and 68: The resistance flywheel rotates on
Page 69 and 70: Section 4 Bearings and joints The l
Page 71 and 72: within the area between each bush (
Page 73: ELLIPTICALS CRANK PULLER MODIFICATI
Page 76 and 77: Technical product matrix Console 20
Page 78 and 79: 1. TUNTURI T-GEN (40-85) Brake cali
Page 80 and 81:
1. TUNTURI T-GEN (40-85) •DC volt
Page 82 and 83:
1. TUNTURI T-GEN (40-85) Error code
Page 84 and 85:
2. 3. Technical specification •Sw
Page 86 and 87:
2. 3. Error codes E-2 •Data conne
Page 88 and 89:
VER. 0.90 Tunturi F30, E40, E45, E6
Page 90 and 91:
SERVICE MANUAL VERSION 0.90 F30 E30
Page 92 and 93:
3 ELECTRONICS SERVICE MANUAL VERSIO
Page 94 and 95:
4 UPDATING SOFTWARE SERVICE MANUAL
Page 96 and 97:
5 CALIBRATION SERVICE MANUAL VERSIO
Page 98 and 99:
SERVICE MANUAL VERSION 0.90 F30 E30
Page 100:
7 APPENDICES TROUBLESHOOTING SERVIC
show all

Service Guide 2009 - Club Piscine

Create successful ePaper yourself

Delete template?

Save as template?