Service Guide 2009 - Club Piscine

More documents

Recommendations

Info

2 ELECTRONICS SERVICE MANUAL VERSION 0.30 The main electrical components of the Tunturi T10 and T20 are user interface (B02), power board (B44), motor (B18), lift motor (B25) speed sensor (B23), and power cable (B29). Figure 1 Tunturi T10 and T20 electrical components and their connections (numbering refers to spare part diagram) 2.1 SERVICE MENUS 2.1.1 Engineering Mode B23 B18 1. Enter the engineering mode after switching the treadmill POWER ON by pushing first ‘SELECT’ and then ‘ENTER’ and hold buttons pressed simultaneously 2. The SPEED window shows the treadmill software version number, TIME window shows the software design year and DISTANCE window shows the design date in “MM.DD” format 3. Press ‘ENTER’ to show LDU version number (Display control software) B25 4. Press ‘ENTER’ to show ISP version number B29 - 3 - B44 B02 B15 (included in B09) FERRITE RING
SERVICE MANUAL VERSION 0.30 5. Press ‘ENTER’ to enter KM/MILE switch mode, 1 for KM, 0 for MILE • Switch between the KM or MILE setting by pressing SPEED +/- or ELEVATION +/- 6. Press ‘ENTER’ to show total distance 7. Press ‘ENTER’ to show total usage hours 8. Press ‘ENTER’ to return to the normal mode 2.1.2 Testing Mode 1. Enter the testing mode after switching the treadmill POWER ON by pushing first ‘SELECT’ and then ‘SPEED DOWN’ and hold buttons pressed simultaneously 2. LED scanning mode for verifying display functionality 3. Press ‘ENTER’ to scan DATA LINES to verify display functionality 4. Press ‘ENTER’ to scan SACN LINES to verify display functionality 5. Press ‘ENTER’ to scan LED’s to verify display functionality 6. After pressing ‘ENTER’ the TIME window shows “test” and the keypad functionality can be tested (the value displayed changes when a button is being pressed) 7. Press ‘ENTER’ to enter IO mode (TIME display shows lift motor potentiometer value, SPEED reads speed from speed sensor and DISTANCE shows heart rate pulse) - 4 - POTENTIOMETER VALUE SPEED VALUE • Press ‘START’ to test lower board relay (a “click” sound) and then press ‘ELEVATION UP’ for 2 seconds to increase the elevation to 8%. Press ‘ELEVATION DOWN’ to decrease the elevation to minimum percentage 0% HR VALUE • Press ‘SPEED UP’ to increase speed value and ‘SPEED DOWN’ to decrease speed value. Press ‘ENTER’ to repeat above test or ‘SELECT’ and ‘ SPEED DOWN’ buttons simultaneously to return to the normal mode 2.1.3 Lift motor calibration The lift motor calibration is done manually by following the following steps: 1. Drive the lift motor to 0% from user interface (inclination display must be 0%) 2. Switch off the treadmill and unplug the power cable 3. Remove motor cover 4. Fold up the running deck 5. Loosen two screws (A) attaching the lift motor nut (B) to the incline frame (Figure 2) 6. Adjust the lift motor nut (B) so that there is 9 mm gap between the upper end of the nut and the lift motor frame (Figure 2) 7. Tighten the screws (A) and verify correct elevation by measuring (Figure 3)
Page 1 and 2: Service Guide 2009
Page 3 and 4: Pliant Delta and Sigma Bremshey Pat
Page 5 and 6: Press „START‟ to test lower boa
Page 7 and 8: Magnet missing from the front rolle
Page 9 and 10: VER. 1.00 TREADLINE Control Trail P
Page 11 and 12: SERVICE MANUAL VERSION 1.00 - 2 - C
Page 13 and 14: 4. Press ‘ENTER’ to show ISP ve
Page 15 and 16: SERVICE MANUAL VERSION 1.00 Lift mo
Page 17 and 18: E7 Instruction in the owner's manua
Page 19 and 20: Speed .............................
Page 21 and 22: VER. 0.30 Service Manual Tunturi T1
Page 23: SERVICE MANUAL VERSION 0.30 1 FOREW
Page 27 and 28: 8 % 810 ± 30 9 % 940 ± 30 10 % 10
Page 29 and 30: E7 Instruction in the owner's manua
Page 31 and 32: SERVICE MANUAL VERSION 0.30 The T10
Page 33 and 34: If the potentiometer has lost its p
Page 35 and 36: TREADMILLS BELT AND DECK REPLACEMEN
Page 37 and 38: BREMSHEY TREADMILLS CHANGING FROM M
Page 39 and 40: BREMSHEY TREADMILLS TESTING & 10 MO
Page 41 and 42: What Creates Static Shock On Treadm
Page 45 and 46: Rear Drive Ellipticals
Page 47 and 48: • Power machine up (If no power r
Page 49 and 50: To access the internal components o
Page 51 and 52: Resistance Mechanisms There are 3 t
Page 53 and 54: Servo Motor Resistance Control The
Page 55 and 56: complains that either of these sett
Page 58 and 59: ( l ) Section 3 Flywheel & Transmis
Page 60 and 61: h . 3. Before replacing the belt en
Page 62 and 63: Type 2 transmission 1. Slacken off
Page 64: 4. Separating drum cover and cross
Page 67 and 68: The resistance flywheel rotates on
Page 69 and 70: Section 4 Bearings and joints The l
Page 71 and 72: within the area between each bush (
Page 73: ELLIPTICALS CRANK PULLER MODIFICATI
Page 76 and 77:
Technical product matrix Console 20
Page 78 and 79:
1. TUNTURI T-GEN (40-85) Brake cali
Page 80 and 81:
1. TUNTURI T-GEN (40-85) •DC volt
Page 82 and 83:
1. TUNTURI T-GEN (40-85) Error code
Page 84 and 85:
2. 3. Technical specification •Sw
Page 86 and 87:
2. 3. Error codes E-2 •Data conne
Page 88 and 89:
VER. 0.90 Tunturi F30, E40, E45, E6
Page 90 and 91:
SERVICE MANUAL VERSION 0.90 F30 E30
Page 92 and 93:
3 ELECTRONICS SERVICE MANUAL VERSIO
Page 94 and 95:
4 UPDATING SOFTWARE SERVICE MANUAL
Page 96 and 97:
5 CALIBRATION SERVICE MANUAL VERSIO
Page 98 and 99:
SERVICE MANUAL VERSION 0.90 F30 E30
Page 100:
7 APPENDICES TROUBLESHOOTING SERVIC
show all

Service Guide 2009 - Club Piscine

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?