easy-to-use and versatile

Electronic indicators,
Dial Gauges, Precision Indicators
E-1

E-2
Error of measurement, µm
20
15
10
5
0
-5
-10
-15
-20
Hysteresis
E L E C T R O N I C I N D I C A T O R S A N D D I A L G A U G E S
EASY-TO-USE AND VERSATILE
As manufacturer of a full range of precision dial gauges for more than 50 years, we are able to provide you with
a wide variety of models.
• Electronic indicators featuring a combined analogue/digital indication with the most up-to-date technology.
• Mechanical dial gauges with high-precision movement and smooth pointer revolution, double-action shockproof
mechanisms as well as measuring spans up to 100 mm.
Which Style Do you Need?
• Digital indication provides error-free readout of the measured values as the fractions of the scale divisions need
not be estimated, visually.
• Analogue indication has the advantage to change smoothly according to the size of the workpiece feature to be
measured. This type of indication is best suited for dynamic measurements, e.g. when determining axial and
radial runout errors.
• Electronic indicators provide many additional functions compared to the mechanical models. For more information,
also read the pages E-8 to E-14.
• Electronic indicators, precision dial gauges as well as dial test indicators have the capability to measure with
the lowest possible hysteresis. Therefore, they are ideally suited for runout inspection where this capability is
required.
• In order to significantly reduce the effects of the systematic errors, we recommend to carry out a number of
comparative measurements because only the actual size of each related nominal length will be read out.
This means that electronic indicators, dial gauges with limited range of indication and precision indicators are
best suited for this purpose.
• These hand-held tools also permit to avoid rough reading errors of the metric range.
• Quality classes: ★★★ Top Quality line – ★★ Standard line – ★ Low cost line.
Standards and Definitions
From now on, the international ISO 463:2006 standard replaces the national ones dealing with dial gauges. Newly
applicable definitions and requirements also imply some changes of the so-called design and metrological characteristics,
which could no be entirely reported in this issue.
This standard, which is part of the matrix «Product Specification (GPS) – Dimensional measuring equipment»,
states the requirements that affect the most significant characteristics mentioned above. Therefore, all values
indicated in this catalogue as limit values for the metrological characteristics only are based on internal
standards proper to our factory.
Electronic indicators
Precision indicators
Definitions used in this section:
Max. perm. errors in one measuring direction
over the whole measuring range
within the local measuring range
in both measuring directions
Repeatability limit
Max. hysteresis
Local measuring
span
Downward plunger movement
Upward plunger movement
Max. error of measurement
0 1 2 3 4 5 6 7 8 9 10
Nominal value, mm
Limits of the permissible error
Mechanical dial gauges
Definitions used in this section for the maximum permissible
errors of a metrological characteristic (MPE):
Error of measurement, µm
20
15
10
5
0
-5
-10
-15
-20
Deviation span
(Error of indication within the measuring range)
Deviation span (error of indication) within
the local measuring span
Total deviation span
(Error of indication within the measuring range)
Repeatability limit of indication
Hysteresis of indication
Hysteresis
Deviation span
Local deviation
span
Downward plunger movement
Upward plunger movement
Total
deviation span
0 1 2 3 4 5 6 7 8 9 10
Nominal value, mm

mm mm mm mm
40 10 10 0÷5÷10 ★ 0141760500 ROCH E-49
10 10 0÷5÷10 ★ 0141760501 ROCH E-49
58 20 10 0÷5÷10 ★ 0141760502 ROCH E-49
30 10 0÷5÷10 ★ 0141760503 ROCH E-49
10 5 0÷2,5÷5 • ★★ 531 COMPAC E-23
58 10 5 0÷2,5÷5 • • ★★ 531B COMPAC E-23
30 5 0÷2,5÷5 • • ★★ 01416038 MERCER E-23
80 10 10 0÷5÷10 ★ 0141760513 ROCH E-49
mm mm mm mm
D I A L G A U G E S
Models with metric reading to 0,1 mm, measuring span up to 30 mm
29 1 1 0÷50÷0 ★★ 01416050 MERCER E-36
40 3 0,5 0÷25÷50
•
•
• • •
★
★
★
0141760560
0141760561
0141760570
ROCH
ROCH
ROCH
E-43
E-43
E-43
★★ 01412010 TESA E-21
40
40
5
5
0,5
0,5
0÷25÷50
0÷25÷0
• •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
★★
★★
★
★★
★★
★★★
★★★
★★★
★★
★★★
★★★
★+
★+
★
★
★
★
01412410
01416014
0141760582
353
353E
01410212
01410210
01410320
01416013
01410211
01410321
0141760635
0141760636
0141760631
0141760632
0141760640
0141760624
TESA
MERCER
ROCH
COMPAC
COMPAC
TESA
TESA
TESA
MERCER
TESA
TESA
ROCH
ROCH
ROCH
ROCH
ROCH
ROCH
01419047
01419048
ETALON
ETALON
E-21
E-21
E-43/42
E-21
E-21
E-15
E-15
E-15
E-21
E-15
E-15
E-44/42
E-44
E-44
E-44
E-44
E-44
58 10 1 0÷50÷100 ★★ 512K COMPAC 01412310 TESA E-24
58
60,4
10
10
1
1
0÷50÷0
0÷50÷100
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
★★
★★
★★
★★
★★★
★★★
★★★
★★
★★★
★★★
★
★
★
01416021
01412411
532
532E
01410612
01410610
01410720
01416020
01410611
01410721
0141761210
0141761211
0141761221
MERCER
TESA
COMPAC
COMPAC
TESA
TESA
TESA
MERCER
TESA
TESA
ROCH
ROCH
ROCH
01412011 TESA
E-24
E-24
E-24
E-24
E-17
E-17
E-17
E-24
E-17
E-17
E-44
E-44
E-45
82 10 1 0÷50÷100 ★★ 01412311 TESA E-28
82 10 1 0÷50÷0
•
•
•
•
★★★
★★★
01410910
01410911
TESA
TESA
E-19
E-19
Classes
Models with metric reading to 0,01 mm, measuring span up to 10 mm
Classes
A-3E-3

E-4
mm mm mm mm
29 0,2 0,2 0÷10÷0 ★★ 01416051 MERCER E-36
40
40
58
58
3
3
5
5
0,2
0,2
0,2
0,2
0÷10÷20
0÷10÷0
0÷10÷20
0÷10÷0
•
•
•
•
•
•
•
•
•
•
★★
★★
★★★
★★
★★
★★
★★
355
355E
01416007
01416035
555
555E
01416034
COMPAC
COMPAC
MERCER
MERCER
COMPAC
COMPAC
MERCER
E-22
E-22
E-16
E-25
E-25
E-25
E-25
mm mm mm mm
D I A L G A U G E S
Models with metric reading to 0,002 mm,
measuring span up to 5 mm
Models with metric reading to 0,001 mm,
measuring span up to 5 mm
40 1 0,2 0÷100/0÷100 • • ★ 0141761261 ROCH E-47
• • ★ 0141761262 ROCH E-47
• ★★ 367 COMPAC 01412510 TESA E-22
40 1 0,1 0÷50÷100 • • ★★ 367E COMPAC 01412710 TESA E-22
• • ★★★ 01410010 TESA E-16
• • ★★★ 01410120 TESA E-16
• • ★★★ 01410011 TESA E-16
40 1 0,1 0÷50÷0
• • ★★★ 01410121 TESA E-16
• ★ 0141761282 ROCH E-48
58 1 0,2 0÷100/0÷100 • • ★ 0141761283 ROCH E-48
• • • ★ 0141761281 ROCH E-48
• • ★ 0141761284 ROCH E-48
• ★★ 567 COMPAC 01412511 TESA E-26
58 1 0,1 0÷50÷100 • • ★★ 567E COMPAC 01412711 TESA E-26
• • ★★★ 01410410 TESA E-18
• • ★★★ 01410520 TESA E-18
• • ★★★ 01410411 TESA E-18
58 1 0,1 0÷50÷0
• • ★★★ 01410521 TESA E-18
0÷100÷200 • ★★ 556 COMPAC 01412611 TESA E-26
58 5 0,2
0÷10÷20 • • ★★ 556E COMPAC E-26
80 1 0,2 0÷100/0÷100 • ★ 0141761291 ROCH E-48
82 5 0,2 0÷10÷20 • ★★ 556G COMPAC E-29
0÷50÷100 • • ★★★ 01410810 TESA E-20
82 1 0,1
0÷50÷0 • • ★★★ 01410811 TESA E-20
Classes
Classes

mm mm mm mm
Classes
60,4
58
58
58
58
80
82
82
82
82
15
30
50
80
100
100
30
50
100
200
1
1
1
1
1
1
1
1
1
1
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
0÷50÷100
•
•
•
•
•
•
•
•
•
•
•
•inv •
•
•inv •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
★ 0141761213
★ 0141761214
★ 0141760651
★ 0141760652
★ 0141760653
★★ 712
★★ 01416039
★ 0141760661
★ 0141760662
★ 0141760663
★★ 722
★ 0141760671
★★ 732
★ 0141761224
★★ 712G
★★★ 01416040
★★ 722G
★★★ 01416041
★★ 732G
★★ 732GB
★★ 752G
ROCH
ROCH
ROCH
ROCH
ROCH
COMPAC
MERCER
ROCH
ROCH
ROCH
COMPAC
ROCH
COMPAC
ROCH
COMPAC
MERCER
COMPAC
MERCER
COMPAC
COMPAC
COMPAC
01419049 ETALON
01412012 TESA
01419050 ETALON
01412013 TESA
01412014 TESA
E-45
E-45
E-45
E-45
E-45/42
E-27
E-27
E-45
E-45
E-45/42
E-27
E-45
E-27
E-45
E-28
E-19
E-28
E-19
E-28
E-28
E-28
mm mm mm mm
D I A L G A U G E S
Long range models with metric reading to 0,01 mm,
measuring span up to 200 mm
Perpendicular models with metric reading to 0,01 mm
38 1 1
0÷50÷0
0÷50÷100
★★
★★
01416060
01416061
MERCER
MERCER
E-37
E-37
40
40
40
±0,4
3
3
5
1
0,5
1
1
4÷0÷4
0÷25÷50
0÷50÷100
0÷50÷100
•
•
•
•
•
★★
★
★★
★★
★
CP352S
0141760566
CP353
CP352
0141760611
COMPAC
ROCH
COMPAC
COMPAC
ROCH
E-38
E-50
E-38
E-38
E-50
mm mm mm mm Classes
40
±0,08
3
0,2
0,2
8÷0÷8
0÷10÷20
•
•
★★
★★
CP355S
CP355
COMPAC
COMPAC
E-38
E-38
Classes
Perpendicular models with metric reading to 0,002 mm
A-5E-5

E-6
mm mm mm mm µm µm µm
40 ±0,2 4,5 20÷0÷20 9 3 3 • ★★ 0141760551 ROCH E-43
9 3 3 • ★★ 353S COMPAC 01412210 TESA E-21
40 ±0,2 3,3 20÷0÷20
9 3 3 • • ★★ 01416031 MERCER E-21
58 ±0,4 9 40÷0÷40 9 3 3 • ★★ 0141760601 ROCH E-44
9 3 3 • ★★ 532S COMPAC 01412211 TESA E-24
58 ±0,4 4 40÷0÷40
9 3 3 • • ★★ 01416032 MERCER E-24
9 3 3 • ★★ 533S COMPAC E-24
58 ±0,5 4 50÷0÷50
9 3 3 • • ★★★ 01416029 MERCER E-17
62 ±0,25 2,5 25÷0÷25 12 5 5 • • ★★ 0141761371 ROCH E-41
mm mm mm mm µm µm µm
40 ±0,08 1,5 8÷0÷8 4 1 1 • ★★ 365S COMPAC E-22
4 1 1 • ★★ 565S COMPAC E-25
58 ±0,08 3,3 8÷0÷8
4 1 1 • • ★★★ 01416030 MERCER E-18
mm mm mm mm µm µm µm
D I A L G A U G E S
Models with restricted range of indication, reading to 0,01 mm in both directions
Models with restricted range of indication, reading to 0,002 mm in both directions
Models with restricted range of indication, reading to 0,001 mm in both directions
40 ±0,04 1,5 4÷0÷4 4 1 1 • ★★ 367S COMPAC E-22
4 1 1 • ★★ 567S COMPAC E-26
58 ±0,04 3,3 4÷0÷4
4 1 1 • • ★★★ 01416028 MERCER E-18
1,2 0,5 0,5 • • ★★ 01419051 ETALON 014161373 ROCH E-41
62 ±0,05 3 50÷0÷50
1,2 0,5 0,5 • • • ★★ 01419052 ETALON E-41
mm mm mm mm mm mN µm µm µm
500 0,8 0,4 0,3 ★★★ 01410420 MCA8-1-500 E-40
62 0,0005 ± 0,025 3 25÷0÷25 150 0,8 0,,4 0,3 ★★★ 01410421 MCA8-1-150 E-40
300 0,8 0,4 0,3 ★★★ 01410422 MCA8-1-300 E-40
500 0,8 0,3 0,3 ★★★ 01410423 MCA8-2-500 E-40
62 0,001 ± 0,05 3 50÷0÷50 150 0,8 0,3 0,3 ★★★ 01410425 MCA8-2-150 E-40
300 0,8 0,3 0,3 ★★★ 01410426 MCA8-2-300 E-40
500 1 0,3 0,3 ★★★ 01410427 MCA8-3-500 E-40
62 0,002 ± 0,1 3 100÷0÷100 150 1 0,3 0,3 ★★★ 01410428 MCA8-3-150 E-40
300 1 0,3 0,3 ★★★ 01410429 MCA8-3-300 E-40
mm mm mm mm mm mN µm µm µm
62 0,001 ± 0,05 3 50÷0÷50 500 0,8 0,3 0,3 ★★★ 01410420 MCA8-1-500 E-40
Classes
Classes
Classes
TESA CARY Micro-comparators MCA-8 with low measuring force
Lateral model
Classes
Classes

mm in in in
29 0.04 0.04 0÷20÷0 71 ★★ 01426050 MERCER E-36
0÷50÷0 181-1 • ★★ 01426010 MERCER E-33
40 0.200 0.1
0÷50÷100 182-1 • ★★ 01426011 MERCER E-33
0÷25÷0 181-1TQ • • ★★★ 01426001 MERCER E-30
40 0.200 0.05
0÷25÷50 182-1TQ • • ★★★ 01426002 MERCER E-30
0÷50÷0 210-1 • ★★ 01426026 MERCER E-34
58 0.400 0.1
0÷50÷100 211-1 • ★★ 01426027 MERCER E-34
58 1 0.1 0÷50÷100 216-1 • • ★★ 01426031 MERCER E-35
mm in in in
0÷25÷0 183-1 • • ★★ 01426012 MERCER E-33
40 0.200 0.05
0÷25÷50 184-1 • • ★★ 01426013 MERCER E-33
40 0.200 0.02 0÷10÷0 183-1TQ • • ★★★ 01426003 MERCER E-30
• ★★ 354A COMPAC E-33
40 0.200 0.02 0÷10÷20 • • ★★ 354AE COMPAC E-33
184-1TQ • • ★★★ 01426004 MERCER E-30
58 ±0.02 20÷0÷20 212SRc-1TQ • • ★★★ 01426025 MERCER E-31
0÷25÷0 212-1 • ★★ 01426020 MERCER E-34
58 0.400 0.05 0÷25÷0 212HD-1TQ • • ★★★ 01426024 MERCER E-31
0÷25÷50 213-1 • ★★ 01426021 MERCER E-34
58 1 0.05 0÷25÷50 217-1 • • ★★ 01426032 MERCER E-35
1 222-1TQ • • ★★★ 01426040 MERCER E-32
82
2 0.05 0÷25÷50 222A-1TQ • • ★★★ 01426041 MERCER E-32
mm in in in
29 0.01 0.01 0÷20÷0 73 ★★ 01426051 MERCER E-36
0÷50÷0 193-1TQ • • ★★★ 01426005 MERCER E-30
40 0.120 0.01 0÷50÷100 194-1TQ • • ★★★ 01426006 MERCER E-30
0÷50÷100 • • ★★ 355AE COMPAC E-33
240-1 • ★★ 01426028 MERCER E-34
58 0.200 0.01 0÷50÷0
240-1TQ • • ★★★ 01426022 MERCER E-31
241-1 • ★★ 01426029 MERCER E-34
58 0.200 0.01 0÷50÷100 • • ★★ 555AE COMPAC E-34
241-1TQ • • ★★★ 01426023 MERCER E-31
mm in in in
38 0,05 0,05
D I A L G A U G E S
Models with inch reading to 0,001 in,
measuring span up to 1 in
Classes
Models with inch reading to 0,0005 in,
measuring span up to 2 in
Classes
Models with inch reading to 0,0001 in,
measuring span up to 2 in
Models with inch reading to 0,001 in
Classes
Classes
0÷25÷0 91 ★★ 01426060 MERCER E-37
0÷25÷50 92 ★★ 01426061 MERCER E-37
A-7E-7

E-8
TESA Models
mm mm in in
01930000 DIGICO 1 30 0,001 / 0,01 1.18 0.00005 / 0.0005
01930001 DIGICO 2 60 0,001 / 0,01 3.36 0.00005 / 0.0005
IP54 model with rubber bellow
S19060524 DIGICO 1 30 0,001 / 0,01 1.18 0.00005 / 0.0005
COMPAC Models*
E L E C T R O N I C I N D I C A T O R S
TESA DIGICO 1 and 2
Electronic Indicators
Both models are remarkable for their versatile functions, long measuring
travel, high accuracy.
• Analogue and digital display; the latter can be displaced for easy
reading in any position.
• Zero setting at any point within the measuring span.
• Data input through the keyboard.
• Counting sense reversal.
• Entry of limit values for classification through displayed symbols.
Additional green, red or amber coloured background in case the tool
is connected to the mains.
• Value storage by means of the functions «Highest value», «Lowest value»
or «Highest value minus lowest value».
01990004 MC 2030-MT
01990006 MC 2060-MT
S19070744 MC 2030-FC
30 mm model with 9 pairs of tolerances
30 mm model with 9 pairs of tolerances
30 mm model with correction against 2 reference standards
* As for TESA DIGICO 1 and 2, all indicated data depend on the measuring span.
✓
LC display
with coloured
background
6 decades plus
minus sign
9 x 4,5 mm digit
height (H x W)
See table
opposite
Metric/inch
conversion
40 mm
scale length
25 scale divisions
According
to selected
tolerances
30,4 mm
(DIGICO 1)
or 60,4 mm
(DIGICO 2)
Incremental
glass scale
max. 1 m/s
Max. 1 m/s
(DIGICO 1) or
max. 2 m/s
(DIGICO 2)
Plunger
guiding on a
plain bearing
Measuring insert with
M2,5 thread
DIGICO 1: 2 µm
DIGICO 2: 3 µm
1 µm
1 µm
See table
on page E-9
RS 232
3,6 V
lithium battery
or mains adapter

≈ 1000 h with
lithium battery
0,002% /°C
10°C to 40°C
–10°C to 50°C
✓
Housing
of regular
models to
IP 54
(IEC 60529)
290 g (DIGICO 1)
310 g (DIGICO 2)
Moved mass
through the measuring bolt:
28 g (DIGICO 1)
27 g (DIGICO 2)
Supplied in a
suited carrying
case along with
1 lithium battery
No. 01960007 and
1 lever No. 01960005
Identification
number
Inspection report
with a declaration
of conformity
✓
Measuring force
Measuring force* close
to plunger stop
– bottom
– top
Hysteresis*
18/17
ø8 h6
ø4,5
6
49
04761037
04761057
01960007
01960005
01960009
01960008
01960010
01960011
04768000
E L E C T R O N I C I N D I C A T O R S
20
30 / 60
57 / 86,5
DIGICO 1 DIGICO 2
0,85 N ± 0,15 N 0,90 N ± 0,20 N
1,10 N ± 0,20 N 1,45 N ± 0,25 N
199 / 233
0,10 N 0,15 N
* Valid with the indicator used vertically, with downward oriented plunger,
or in static measurement.
9
Accessories for TESA DIGICO 1 and 2
29
230 V mains adapter, 50 Hz, 9 V, 200 mA,
1,8 VA
110 V mains adapter
3,6 V lithium battery, LR6, AA
Lever for plunger retraction
Connector for vacuum plunger lift,
suitable for DIGICO 1
Same as above, but for DIGICO 2
Connector for pneumatic plunger retraction,
suitable for DIGICO 1 only
Adapter for use of the mains adapter
together with the switch for triggering
data transfer
Hand switch
for triggering data transfer
For ordering information on connecting cable etc., see section N
01960008
01960009
01960010
ø3
ø3
ø3
A-9E-9

E-10
ø 60
ø 12
ø8 h6
ø 4
M2,5
E L E C T R O N I C I N D I C A T O R S
TESA DIGICO 10 and 11 as well as
MIN/MAX Electronic Indicators
These three versions are made for optimum adaptation to your metrology
applications.
• Zero-setting of display anywhere within the measuring span.
• Display and keyboard rotating through 270°.
• Ability to hold the measured values.
• Digit entry (PRESET function).
• Two datum points.
• Digital output.
Models TESA DIGICO 10
Provided with all the features listed above.
ø10
B
A
56.6
34.9 47.4
9,5 21,5
24,5
ø 12
ø8 h6
B
A
✓
6-dcade
LC display.
plus minus sign
8,5 mm
digit height
See tables
Metric/inch
conversion
Glass scale with
incremental divisions,
capacitive
Max. perm.:
1,5 m/s
Case in light
alloy. Front face
in polyamide.
Stainless steel plunger
guided on a plain bearing.
Measuring insert with a
M2,5 thread.
See tables
0,01 mm = 10 µm
0,001 mm = 2 µm
2 µm
(0,001 mm)
See table
on page E-12
RS 232,
opto-coupled
3V lithium battery,
type CR 2032
DIGICO 10
≈ 4000 h.
DIGICO 11/
MIN/MAX ≈ 2000 h
5°C to 40°C
-20°C to 60°C
EN 50081-1:1993
EN 50082-1:1993

IP51
(IEC 60529)
See tables
Supplied in a
suited carrying
case including
1 lithium battery, type
CR 2032 (No. 01961000)
Identification
number
Inspection report
with a declaration
of conformity
mm mm µm g A mm B mm in in
01930110* 12,5 0,01 10 120 69,9 64 0.5 0.0005
01930111* 25 0,01 10 130 82,4 64 1 0.0005
01930112* 50 0,01 20 210 150,5 90,5 2 0.0005
01930113* 100 0,01 20 250 250,5 140,5 4 0.0005
01930101 12,5 0,001 5 120 69,9 64 0.5 0.00005
01930100 25 0,001 5 130 82,4 64 1 0.00005
01930102 50 0,001 12 210 150,5 90,5 2 0.00005
01930103 100 0,001 15 250 250,5 140,5 4 0.00005
* Delivered without inspection report.
Models
TESA DIGICO 11
With same base features as set forth plus
the following functions:
E L E C T R O N I C I N D I C A T O R S
• Possible entry of limit values for classification
through colour LEDs: green for «Good», red for
«Scrap», amber for «Rework».
• Value storage using the functions «Highest value»,
«Lowest value» and «Highest value minus lowest
value».
• Counting sense reversal.
mm mm µm g A mm B mm in in
01930104 12,5 0,001 5 120 69,9 64 0.5 0.00005
01930105 25 0,001 5 130 82,4 64 1 0.00005
Models TESA DIGICO MIN/MAX
With same key features as TESA DIGICO 11, except for the PRESET function that’s unavailable
when used in normal mode. Provided without LEDs for value classification.
• Mainly used for registering the measured values through the function «Highest value minus
lowest value».
mm mm µm g A mm B mm in in
01930120 12,5 0,001 5 120 69,9 64 0.5 0.00005
A-11 E-11

E-12
3
Measuring force
E L E C T R O N I C I N D I C A T O R S
mm Lower limit value Upper limit value
12,5 0,7 N 0,95 N
25 0,6 N 1,1 N
50 2,5 N 4,0 N
100 2,5 N 4,0 N
With the indicator used vertically and downward oriented plunger, or in static measurement.
Accessories for TESA DIGICO 10 and 11
as well as MIN/MAX
6
12
5
4
8
7
Ø58.8
2
Ø58.8
6.35
10
9
3.5 ∏ 6 bar
01961000 Lithium battery, type CR 2032, 3 V, 190 mAh
Suited for
all models
01961009 1 Top mounted dust cap
L = 23 mm 12,5 mm
01961010 L = 36 mm 25 mm
01961003 2 Back with lug all models
01960005 3 Plunger retracting lever, at the bottom all models
01961005 4 Plunger retracting lever, at the top
2,5 mm/25 mm
01961011 5 Plunger retracting cable, at the top
2,5 mm/25 mm
01961006 6 Pneumatic device for plunger retraction,
alone without foot switch
12,5 mm/25 mm
01961008 7 Foot switch with pressure regulator for N 12,5 mm/25 mm
01961007 8
12,5 mm/25 mm
S19001431 9 50 mm/100 mm
S19001448 10
S19001447 11
01961002 12
o 01961006
Pneumatic device for plunger retraction, complete
with foot switch and pressure regulator
Vacuum lifting device
Pressure regulator for No S19001431
Foot switch for No S19001431
Flat back all models
For ordering information on connecting cable etc., see section N.
Ø12
1
19
Ø 6.35
h
11
✓

✓
LCD,
5 digits + sign
6 mm
digit height
Zero-setting
of display
20 µm
5 µm
0,5 to 0,9 N
(±0,15 N)
Max. 2 m/s
Number of
measurements
per second: 7
Working temper -
ature range:
+5°C to +40°C
3V lithium battery,
type CR 2032
Battery life
> 3500 hours
RS 232
70 g
EN 61326-1
IP65 (IEC 529)
Shipping
packaging
incl. 1 lithium
battery, type CR 2032
(No. 01961000)
Serial number
Declaration
of conformity
without for
models 0,01 mm
with for
models 0,001 mm
101.5
1,65
13
8,54
6,4
Ø 8 h6
Ø 4
Ø 44
ø 1,5
19.3
5
E L E C T R O N I C I N D I C A T O R S
TESA DIGICO 12
Small Electronic Dial Gauges
Made to measure in extreme workshop conditions – Water and coolant
resistant (IP65) – Housing with a 44 mm diameter – Let you take advantage
of the mechanics combined with digital reading.
Models TESA DIGICO 12 – Standard
• 44 mm dia. dial gauge housing.
• Water and coolant resistant (IP65).
• RS 232 data output combined with external
power supply.
• Inductive measuring system, patented.
• Choice between absolute («ABS») and
relative («REL») modes.
• Numerical display.
• Possible setting of PRESET value to ±200 mm.
• Switchable measuring direction.
• Direct metric/inch conversion.
• Automatic shut down.
13
42.5
13 18 58 12.5
mm/in mm in
01930130 12,5/0.5 0,01 0.0005 IP65
01930132 12,5/0.5 0,001 / 0,01 0.00005 / 0.0005 IP65
01930131 12,5/0.5 0,01 0.0005 IP65
01930133 12,5/0.5 0,001 / 0,01 0.00005 / 0.0005 IP65
58
18
25.8
101.8
Module
Models to IP65 with electronic module protected against the penetration of liquids
Models to IP65 with both mechanics and electronics protected against the penetration of liquids
A-13 E-13

E-14
9,5
14,3
19,05
26,2
1,65
ø 6,4
6,4
03238013
01961012
01960005
01961013
04761060
01961000
mm/in mm in
01930134 5/0.210 0,001 / 0,01 0.00005 / 0.0005 IP65
01930135 5/0.210 0,001 / 0,01 0.00005 / 0.0005 IP65
8,54
6,4
Accessories
E L E C T R O N I C I N D I C A T O R S
Models TESA DIGICO 12 – HP
• High-precision measuring system.
• Water and coolant resistant (IP65).
• Combined analogue/digital display.
• Analogue readoutfrom ±0,025 to ±1,25 mm.
• Measuring modes NOR/MIN/MAX/MAX-MIN.
• Housing with a 44 mm diameter dial.
• RS 232 data output combined with external power supply.
• Inductive measuring system, patented.
• Zero-setting of display.
• Direct metric/inch conversion.
• Auto shut down. Can also be locked.
Models to IP65 with electronic module protected against the penetration of liquids
03238013 01961012 01961013
ø 1,5
50
24.5
10
50.5
18
16.3
84.8
86.5
55
13
Ø 4
52.5
Ø 8 h6
1
15
Ø 44
5
9
Module
Model to IP65 with both mechanics and electronics protected against the penetration of liquids
Back with lug
Upper lift lever
Lower lift lever
Pneumatic retraction device
RS 232 connecting cable with external power supply
3 V lithium battery, type CR 2032, 190 mAh
19.3
5
5
42.5
13
5.5 18 50.5 12.5
Ø 2.5/4
✓
LCD,
5 digits + sign
6 mm
digit height
Zero-setting
of display
4 µm
2 µm
0,4 to 0,75 N
(±0,15 N)
Max. 2 m/s
Number of
measurements
per second: 9
Working temper -
rature range:
+5°C to +40°C
3V lithium
battery,
type CR 2032
Battery life
> 4000 hours
RS 232
70 g
EN 61326-1
IP65 (IEC 529)
Shipping
packaging
including
1 lithium battery, type
CR 2032 (No. 01961000)
Serial number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory standard
0,01 mm
2,2 mm
Rotating dial.
Regular models
with dial lock.
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers.
Insert with
M2,5 thread
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
TOP Quality line
29
48.4
37
ø37
6
ø3
6.5 14.5
ø10
ø8 h6
ø4
ø5
mm mm mm mm
ø40
01410210 0,01 5 5,4 • 0,5 0 ÷ 25 ÷ 50 •
01410211 0,01 5 5,4 • 0,5 0 ÷ 25 ÷ 0 •
01410212 0,01 5 5,4 • 0,5 0 ÷ 25 ÷ 50 –
TOP Quality line IP54 protected against the penetration of liquids
01410320 0,01 5 5,4 • 0,5 0 ÷ 25 ÷ 50 –
01410321 0,01 5 5,4 • 0,5 0 ÷ 25 ÷ 0 –
Permissible limits of a metrological characteristic (MPE/MPL)
Deviation span
Deviation span within the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force TOP Quality line
TOP Quality line IP54
D I A L G A U G E S
TESA YR and MERCER
Precision Dial Gauges – TOP Quality
These TOP Quality precision dial gauges combine excellent metrological
properties with extra-long life.
• Smooth, full-jewelled movement with rubies.
• Full-metal bezel and case housing.
• Shock proof mechanism effective in the two directions
towards the plunger moves.
• Non-dazzling dial.
• Swiss Made.
TESA YR – TOP Quality
40 mm dial diameter, 0,01 mm reading
(77.4)
57
37 30
ø37
6
ø3
ø10
0,01 mm
12 µm
6 µm
14 µm
3 3 µm µm
6.5 14.5
3 3 µm µm
≤ 1,4 N
≤ 2 N
ø8 h6
ø5
ø40
A-15 E-15

E-16
TOP Quality line, with dial lock
mm mm mm mm
01410010 0,001 1 1,5 • 0,1 0 ÷ 50 ÷ 100
01410011 0,001 1 1,5 • 0,1 0 ÷ 50 ÷ 0
01416007 195-1TQ 0,002 3 3,3 • 0,2 0 ÷ 10 ÷ 0
TOP Quality line IP54 protected against the penetration of liquids, without dial lock
01410120 0,001 1 1,5 • 0,1 0 ÷ 50 ÷ 100
01410121 0,001 1 1,5 • 0,1 0 ÷ 50 ÷ 0
Permissible limits of a metrological characteristic (MPE/MPL)
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force TOP Quality line
TOP Quality line IP54
29
48.4
37
ø37
6
ø3
6.5 14.5
ø10
ø8 h6
ø4
ø5
D I A L G A U G E S
TESA YR and MERCER Dial Gauges – TOP Quality
40 mm dial diameter, 0,001 or 0,002 mm reading
ø40
(77.4)
57
37 30
ø37
6
ø3
0,002 mm 0,001 mm
10 µm 4 µm
6 µm 4 µm
12 µm 5 µm
1,5 µm 1 µm
2 µm 1 µm
≤ 1,4 N ≤ 1,7 N
≤ 2 N
6.5 14.5
ø10
ø8 h6
ø5
ø40
✓
EN ISO 463
Factory
standard
0,001 mm
0.002 mm
1,1 mm
Rotating dial.
Regular
models with
dial lock
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers
Measuring insert
with M2,5 thread.
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory standard
0,01 mm
1,5 mm
Rotating dial.
Regular
models with
dial lock
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread.
3 mm dia.
ball tip, already
mounted
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
TOP Quality line, with dial lock
mm mm mm mm
01410610 0,01 10 10,5 • 1 0 ÷ 50 ÷ 100
01410611 0,01 10 10,5 • 1 0 ÷ 50 ÷ 0
01410612 0,01 10 10,5 • 1 0 ÷ 50 ÷ 100
TOP Quality line IP54 protected against the penetration of liquids, without dial lock
01410720 0,01 10 10,5 • 1 0 ÷ 50 ÷ 100
01410721 0,01 10 10,5 • 1 0 ÷ 50 ÷ 0
TOP Quality line with restricted reading range
01416029 250SRc-1TQ 0,01 ±0,5 4 • 1 50 ÷ 0 ÷ 50
Permissible limits of a metrological characteristic (MPE/MPL)
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force TOP Quality line
TOP Quality line IP54
(111)
ø57
6
ø8 h6
15.7
ø4.5
ø5
ø10
9
ø3
ø53
50
43
68
D I A L G A U G E S
TESA YR and MERCER Dial Gauges – TOP Quality
57 or 58 mm dial diameter, 0,01 mm reading
(142.5)
ø58
6
ø8 h6
15.7
ø5
10
ø3
ø53
50
57.5
85
0,01 mm 0,01 mm
1 mm 10 mm
7 µm 15 µm
5 µm 8 µm
9 µm 17 µm
3 µm 3 µm
3 µm 3 µm
≤ 1,4 N ≤ 1,4 N
≤ 2,2 N
A-17 E-17

E-18
TOP Quality line, with dial lock
mm mm mm mm
01410410 0,001 1 3,3 • 0,1 0 ÷ 50 ÷ 100
01410411 0,001 1 3,3 • 0,1 0 ÷ 50 ÷ 0
TOP Quality line IP54 protected against the penetration of liquids, without dial lock
01410520 0,001 1 3,3 • 0,1 0 ÷ 50 ÷ 100
01410521 0,001 1 3,3 • 0,1 0 ÷ 50 ÷ 0
TOP Quality line with restricted reading range
01416030 253SRc-1TQ 0,002 ±0,08 3 • 0,16 8 ÷ 0 ÷ 8
01416028 SRc 0,001 ±0,04 3 • 0,08 40 ÷ 0 ÷ 40
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force TOP Quality line
TOP Quality line IP54
(105)
ø58
6
ø8 h6
15.7
ø4.5
ø5
ø10
9
ø3
ø53
50
43
62
D I A L G A U G E S
TESA YR and MERCER Dial Gauges – TOP Quality
57 or 58 mm dial diameter, 0,001 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
(129)
ø58
6
ø8 h6
15.7
ø5
10
ø3
ø53
50
0,002 mm 0,001 mm 0,001 mm
1 mm 0,08 mm
2 µm 4 µm 1,5 µm
2 µm 4 µm 1,5 µm
4 µm 5 µm 4 µm
1 µm 1 µm 1 µm
1 µm 1 µm 1 µm
≤ 1,5 N ≤ 1,7 N ≤ 1,5 N
≤ 2 N
57.5
71.5
✓
EN ISO 463
Factory
standard
0,01 mm
0,001 mm
0.002 mm
1,5 mm
Rotating dial.
Regular
models with
dial lock.
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers
Measuring insert
with M2,5 thread.
3 mm dia.
ball tip, already
mounted
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory
standard
0,01 mm
2,3 mm
Rotating dial,
lockable.
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers
Measuring insert
with M2,5 thread.
3 mm dia.
ball tip, already
mounted
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
TOP Quality line, with dial lock
mm mm mm mm
01410910 0,01 10 10,5 • 0,1 0 ÷ 50 ÷ 100
01410911 0,01 10 10,5 • 0,1 0 ÷ 50 ÷ 0
TOP Quality line with long range and dial lock
01416040 259-1TQ 0,01 30 30,5 • 0,1 0 ÷ 50 ÷ 100
01416041 259A-1TQ 0,01 50 50,5 • 0,1 0 ÷ 50 ÷ 100
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YR and MERCER Dial Gauges – TOP Quality
82 mm dial diameter, 0,01 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
(121)
ø82
6
19,2
ø5
ø10
9
ø8 h6
ø4.5
ø3
ø53
60
43
78
ø82
19.2
15.7
ø8h6
M 2,5 - 6H
ø4.5
20/19
6
10/9
10 mm 30 mm 50 mm
15 µm 20 µm 25 µm
8 µm 20 µm 25 µm
17 µm 25 µm 30 µm
3 µm 3 µm 3 µm
3 µm 5 µm 5 µm
≤ 1,4 N ≤ 2,2 N ≤ 2,5 N
ø5
ø3
ø6.4
60
98 / 117,2
158 / 228
A-19 E-19

E-20
TOP Quality line, with dial lock
mm mm mm mm
01410810 0,001 1 3,3 • 0,1 0 ÷ 50 ÷ 100
01410811 0,001 1 3,3 • 0,1 0 ÷ 50 ÷ 0
Deviation span
Deviation span within the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YR Dial Gauges – TOP Quality
82 mm dial diameter, 0,001 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
(145)
ø82
6
19,2
ø5
ø10
9
ø4.5
ø3
4 µm
4 µm
5 µm
1 µm
1 µm
ø8 h6
≤ 1,7 N
ø53
60
0,001 mm
43
72
✓
EN ISO 463
Factory
standard
0,001 mm
2,3 mm
Rotating dial,
lockable.
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread.
3 mm dia.
ball tip, already
mounted
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory
standard
0,01 mm
2,2 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread.
3 mm dia.
ball tip, already
mounted
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
Standard line
mm mm mm mm
01412010 0,01 5 5,4 – – 0,5 0 ÷ 25 ÷ 50
01416013 x185-1 0,01 5 5,4 – • 0,5 0 ÷ 25 ÷ 0
01416014 186-1 0,01 5 5,4 – • 0,5 0 ÷ 25 ÷ 50
353 0,01 5 5,4 • – 0,5 0 ÷ 25 ÷ 50
Standard line IP54 protected against the penetration of liquids
01412410 0,01 5 5,4 – – 0,5 0 ÷ 25 ÷ 50
353E 0,01 5 5,4 • – 0,5 0 ÷ 25 ÷ 50
Standard line with restricted reading range
01412210 0,01 ±0.2 3,3 • – 0,5 20 ÷ 0 ÷ 20
01416031 SRc 0,01 ±0.2 3,3 • • 0,5 20 ÷ 0 ÷ 20
353S 0,01 ±0.2 3,3 • – 0,5 20 ÷ 0 ÷ 20
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force Standard line
Standard line IP54
D I A L G A U G E S
TESA YE, MERCER and COMPAC
Precision Dial Gauges – Standard
40 mm dial diameter, 0,001 mm reading
Remarkably robust, these precision dial gauges are essential for the
workshop.
• Smooth, jewelled movement with rubies.
• Full-metal case housing.
• Optimum protection against shocks.
• Swiss Made.
Permissible limits of a metrological characteristic (MPE/MPL)
29
48.4
37
ø37
6
ø3
6.5 14.5
ø10
ø8 h6
ø4
ø5
ø40
(77.4)
57
5 mm ± 0,2 mm
12 µm 7 µm
6 µm 5 µm
37 30
ø37
14 µm 9 µm
3 µm 3 µm
6
3 µm 3 µm
≤ 1,4 N ≤ 1,4 N
≤ 2 N
ø3
6.5 14.5
ø10
ø8 h6
ø5
ø40
A-21 E-21

E-22
Standard line
29
48.4
37
ø37
6
6.5 14.5
ø8 h6
ø4
mm mm mm mm
355 0,002 3 3,3 • – 0,2 0 ÷ 10 ÷ 20
01412510 0,001 1 1,5 • • 0,1 0 ÷ 50 ÷ 100
367 0,001 1 1,5 • – 0,1 0 ÷ 5 ÷ 10
Standard line IP54 protected against the penetration of liquids
ø10
ø5
355E 0,002 3 3,3 • – 0,2 0 ÷ 10 ÷ 20
01412710 0,001 1 1,5 • – 0,1 0 ÷ 50 ÷ 100
367E 0,001 1 1,5 • – 0,1 0 ÷ 5 ÷ 10
Standard line with restricted reading range
ø40
(77.4)
365S 0,002 ±0,08 1,5 • – 0,2 8 ÷ 0 ÷ 8
367S 0,001 ±0,04 1,5 • – 0,1 4 ÷ 0 ÷ 4
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force Standard line
Standard line IP54
ø3
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
40 mm dial diameter, 0,001 or 0,002 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
57
37 30
ø37
6
ø3
6.5 14.5
ø10
ø5
ø8 h6
ø40
3 mm 1 mm ±0,08/±0,04 mm
10 µm 4 µm 2 µm
6 µm 4 µm 2 µm
12 µm 5 µm 4 µm
1,5 µm 1 µm 1 µm
2 µm 1 µm 1 µm
≤ 1,4 N ≤ 1,4 N ≤ 1,4 N
≤ 1,7 N ≤ 1,7 N
✓
EN ISO 463
Factory
standard
0,001 mm
0,002 mm
1,1 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel.
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread.
3 mm dia.
ball tip, already
mounted
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory
standard
0,1 mm
1,5 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel.
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread.
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
(111)
ø58
6
Standard line
ø8 h6
15.7
ø4.5
ø5
ø10
9
ø3
ø53
50
M 2,5 - 6H
43
68
mm mm mm mm
531 0,1 10 10,5 • – 5 0 ÷ 2,5 ÷ 5
531B 0,1 10 10,5 • – 5 0 ÷ 2,5 ÷ 5
01416038 249-1 0,1 30 30,5 • • 5 0 ÷ 5
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
58 mm dial diameter, 0,1 mm reading
ø58
ø8h6
M 2,5 - 6H
Permissible limits of a metrological characteristic (MPE/MPL)
15.7
ø4.5
ø5
20
ø3
6
10
ø6.4
50
88
148
10 mm 30 mm
30 µm 30 µm
35 µm 40 µm
5 µm 10 µm
10 µm 10 µm
≤ 1,5 N ≤ 2,2 N
A-23 E-23

E-24
(111)
ø57
6
Standard line
ø8 h6
15.7
ø4.5
ø5
ø10
9
ø3
ø53
50
43
mm mm mm mm
01412011 0,01 10 10,5 • – 1 0 ÷ 50 ÷ 100
01412310 0,01 10 10,5 – – 1 0 ÷ 50 ÷ 100
01416020 250-1 0,01 10 10,5 – • 1 0 ÷ 50 ÷ 0
01416021 251-1 0,01 10 10,5 – • 1 0 ÷ 50 ÷ 100
512K JET 0,01 10 10,5 – – 1 0 ÷ 50 ÷ 100
532 0,01 10 10,5 • – 1 0 ÷ 50 ÷ 100
Standard line IP54 protected against the penetration of liquids
68
01412411 0,01 10 10,5 – – 1 0 ÷ 50 ÷ 100
532E 0,01 10 10,5 • – 1 0 ÷ 50 ÷ 100
Standard line with restricted reading range
01412211 0,01 ±0,4 4 • – 1,27 40 ÷ 0 ÷ 40
01416032 0,01 ±0,4 4 • – 1,27 40 ÷ 0 ÷ 40
532S 0,01 ±0,4 4 • • 1,27 40 ÷ 0 ÷ 40
533S 0,01 ±0,5 4 • – 1,27 50 ÷ 0 ÷ 50
Deviation span
Deviation span within
the local measuring span 0,10 mm
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force Standard line
Standard line IP54
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
58 mm dial diameter, 0,01 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
(142.5)
ø58
6
ø8 h6
15.7
ø5
10
ø3
ø53
50
57.5
85
10 mm ±0,4 / ±0,5 mm
15 µm 7 µm
8 µm 5 µm
17 µm 9 µm
3 µm 3 µm
3 µm 3 µm
≤ 1,5 N ≤ 1 N
≤ 2,2 N
✓
EN ISO 463
Factory
standard
0,01 mm
1,5 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread.
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory
standard
0,002 mm
1,5 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel.
Adjustable
tolerance markers
Measuring insert
with M2,5 thread.
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
Standard line
(105)
ø58
6
15.7
ø4.5
ø5
ø10
9
ø3
ø53
ø8 h6
50
43
62
mm mm mm mm
01416034 253-1 0,002 5 5,3 – • 0,2 0 ÷ 10 ÷ 0
01416035 254-1 0,002 5 5,3 – • 0,2 0 ÷ 10 ÷ 20
555 0,002 5 5,3 • – 0,2 0 ÷ 10 ÷ 20
Standard line IP54 protected against the penetration of liquids
555E 0,002 5 5,3 • – 0,2 0 ÷ 10 ÷ 20
Standard line with restricted reading range
565S 0,002 ±0.08 3,3 • – 0,2 8 ÷ 0 ÷ 8
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force Standard line
Standard line IP54
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
58 mm dial diameter, 0,002 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
(129)
ø58
6
15.7
ø8 h6
ø5
10
ø3
ø53
50
57.5
71.5
5 mm ±0,4 / ±0,5 mm
12 µm 4 µm
14 µm 4 µm
2 µm 1 µm
2 µm 1 µm
≤ 1,5 N ≤ 1,5 N
≤ 1,7 N
A-25 E-25

E-26
Modèles Standard Standard line
(105)
ø58
ø4.5
ø8 h6
mm mm mm mm
01412611 0,001 5 5,3 ✓ – 0,2 0 ÷ 100 ÷ 200
• 556 0,001 5 5,3 ✓ – 0,2 0 ÷ 10 ÷ 20
• 01412511 0,001 1 1,5 ✓ – 0,1 0 ÷ 50 ÷ 100
• 567 0,001 1 3,3 ✓ – 0,1 0 ÷ 5 ÷ 10
•
Modèles Standard Standard line IP54 IP54 protected protégés against contre the les penetration projections of liquids de liquides
556E 0,001 5 5,3 ✓ – 0,2 0 ÷ 10 ÷ 20
• 01412711 0,001 1 1,5 ✓ – 0,1 0 ÷ 50 ÷ 100
• 567E 0,001 1 3,3 ✓ – 0,1 0 ÷ 5 ÷ 10
•
Modèle Standard Standard line with à restricted course limitée reading range
6
15.7
ø5
ø10
9
ø3
ø53
50
43
62
567S 0,001 ±0,04 3,3 ✓ – 0,1 4 ÷ 0 ÷ 4
•
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force Standard line
Standard line IP54
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
58 mm dial diameter, 0,001 mm reading
Permissible limits of a metrological characteristic (MPE/MPL)
(129)
ø58
6
15.7
ø8 h6
ø5
10
ø3
ø53
5 mm 1 mm ±0,4
12 µm 4 µm 4 µm
14 µm 5 µm 4 µm
2 µm 1 µm 1 µm
2 µm 1 µm 1 µm
≤ 1,5 N ≤ 1,5 N ≤ 1,5 N
≤ 1,7 N ≤ 1,7 N
50
57.5
71.5
✓
EN ISO 463
Factory
standard
0,002 mm
1,5 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel.
Adjustable
tolerance markers
Measuring insert
with M2,5 thread.
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory
standard
0,01 mm
1,5 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel.
Adjustable
tolerance markers
Measuring insert
with M2,5 thread.
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
ø58
F
M 2,5 - 6H
15.7
ø4.5
ø5
ø3
E
6
D
ø6.4
C
B
A
mm 30 mm 50 mm 100 mm
A 148 228 390
B 88 117,2 211,6
C 50 60 103,6
D 10 9 9
E 20 19 19
F Ø 8h6 Ø 8h6 Ø 8h6
mm
Standard line with long range
mm mm mm
01412012 0,01 30 30,5 • – 1 0 ÷ 50 ÷ 100
01416039 252-1 0,01 30 30,5 • • 1 0 ÷ 50 ÷ 100
712 0,01 30 30,5 • – 1 0 ÷ 50 ÷ 100
01412013 0,01 50 50,5 • – 1 0 ÷ 50 ÷ 100
722 0,01 50 50,5 • – 1 0 ÷ 50 ÷ 100
732 0,01 100 100,5 • – 1 0 ÷ 50 ÷ 100
Permissible limits of a metrological characteristic (MPE/MPL)
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YE, MERCER and COMPAC
Dial Gauges – Standard
58 mm dial diameter, 0,01 mm reading,
long range
30 mm 50 mm 100 mm
20 µm 25 µm 30 µm
25 µm 30 µm 35 µm
3 µm 3 µm 3 µm
5 µm 5 µm 8 µm
≤ 2,2 N ≤ 2,5 N ≤ 3,2 N
A-27 E-27

E-28
ø82
M 2,5 - 6H
19.2
15.7
F
ø4.5
ø5
E
ø3
6
D
ø6.4
C
B
A
mm
Standard line with long range
mm mm mm
01412311 0,01 10 10,5 – – 1 0 ÷ 50 ÷ 100
712G 0,01 30 30,5 • – 1 0 ÷ 50 ÷ 100
722G 0,01 50 50,5 • – 1 0 ÷ 50 ÷ 100
01412014 0,01 100 100,5 • – 1 0 ÷ 50 ÷ 100
732G 0,01 100 100,5 • – 1 0 ÷ 50 ÷ 100
732GB 0,01 100 100,5 • • 1 0 ÷ 50 ÷ 100
752G 0,01 200 200,5 • – 1 0 ÷ 50 ÷ 100
Permissible limits of a metrological characteristic (MPE/MPL)
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
82 mm dial diameter, 0,01 mm reading,
long range
mm 10 mm 30 mm 50 mm 100 mm 200 mm
A 121 158 228 390 752
B 78 98 117,2 211,6 437
C 60 60 60 103,6 150
D 9 10 9 9 10,4
E 19 20 19 19 20,2
F Ø 8h6 Ø 8h6 Ø 8h6 Ø 8h6 Ø 12
10 mm 30 mm 50 mm 100 mm 200 mm
15 µm 20 µm 25 µm 30 µm 45 µm
17 µm 25 µm 30 µm 35 µm 50 µm
3 µm 3 µm 3 µm 3 µm 3 µm
3 µm 5 µm 5 µm 8 µm 10 µm
≤ 1,4 N ≤ 2,2 N ≤ 2,5 N ≤ 3,2 N ≤ 4 N
✓
EN ISO 463
Factory
standard
0,01 mm
2,3 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
Measuring insert
with a M2,5 thread
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity

✓
EN ISO 463
Factory
standard
0,001 mm
2,2 mm
Rotating dial
Full-metal
case housing.
Fixing shank
and plunger in hardened
stainless steel
Measuring insert
with a M2,5 thread
3 mm dia.
ball tip, already
mounted.
Cardboard box
Identification
number
Inspection report
with a declaration
of conformity
Standard line
mm mm mm mm
556G 0.001 5 5,3 • – 0,2 0 ÷ 10 ÷ 20
Permissible limits of a metrological characteristic (MPE/MPL)
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
82 mm dial diameter, 0,001 mm reading
(145)
ø82
6
19,2
ø5
ø10
9
ø8 h6
ø4.5
ø3
ø53
5 mm
12 µm
14 µm
2 µm
2 µm
60
≤ 1,5 N
43
72
A-29 E-29

E-30
Models to 0.001, 0.0005 and 0.0001 in
TOP Quality line, with dial lock
in in in in
01426001 181-1TQ 0.001 0.200 0.212 • 0.05 0 ÷ 25 ÷ 0
01426002 182-1TQ 0.001 0.200 0.212 • 0.05 0 ÷ 25 ÷ 50
01426003 183-1TQ 0.0005 0.200 0.212 • 0.02 0 ÷ 10 ÷ 0
01426004 184-1TQ 0.0005 0.200 0.212 • 0.02 0 ÷ 10 ÷ 20
01426005 193-1TQ 0.0001 0.120 0.130 • 0.01 0 ÷ 50 ÷ 0
01426006 194-1TQ 0.0001 0.120 0.130 • 0.01 0 ÷ 50 ÷ 100
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
MERCER Precision Dial Gauges –
TOP Quality
Series 180, 40 mm dial diameter, inch reading
Permissible limits of a metrological characteristic (MPE/MPL)
ø10
0.001 in 0.0005 in 0.0001 in
0.0005 in 0.0005 in 0.0004 in
0.0006 in 0.0006 in 0.0005 in
0.00015 in 0.00015 in 0.00006 in
0.00015 in 0.00015 in 0.00008 in
≤ 1.4 N ≤ 1.4 N ≤ 1.7 N
29
48.4
37
ø37
6
ø3
6.5 14.5
ø8 h6
ø4
ø5
ø40
(77.4)
✓
Factory
standard
0.001 in
0.0005 in
0.0001 in
0.001 in: 2,2 mm
0.0005 in: 3,1 mm
0.0001 in: 1,1 mm
Rotating dial.
Can be locked.
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers.
Measuring insert
with a M2.5 thread.
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity

✓
Factory
standard
0.0005 in
0.0001 in
1,5 mm
Rotating dial.
Can be locked.
Full-metal
case housing.
Fixing shank
and stainless steel plunger,
hardened.
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers.
Measuring insert
with a M2.5 thread.
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity
Models to 0.0005 and 0.0001 in
TOP Quality line, with dial lock
in in in in
01426024 212HD-1TQ 0.0005 0.400 0.42 • 0.05 0 ÷ 25 ÷ 0
01426022 240-1TQ 0.0001 0.200 0.21 • 0.01 0 ÷ 50 ÷ 0
01426023 241-1TQ 0.0001 0.200 0.21 • 0.01 0 ÷ 50 ÷ 100
TOP Quality line with restricted reading range
01426025 212SRc-1TQ 0.0005 ±0.020 0.150 • 0.2 20 ÷ 0 ÷ 20
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
MERCER Dial Gauges – TOP Quality
S series , 58 mm dial diameter, inch reading
Permissible limits of a metrological characteristic (MPE/MPL)
ø8 h6
ø4.5
0.005 in 0.001 in 0.001 in
0.200 in ± 0.020 in
0.0006 in 0.0005 in 0.0003 in
0.0007 in 0.0006 in 0.0004 in
0.00015 in 0.00006 in 0.00012 in
0.00015 in 0.00008 in 0.00012 in
≤ 1.5 N ≤ 1.5 N ≤ 1.5 N
(105)
ø58
6
15.7
ø5
ø10
9
ø3
ø53
50
43
62
A-31 E-31

E-32
Models to 0.0005 in
TOP Quality line, with dial lock
in in in in
01426040 222-1TQ 0.0005 1 1.02 • 0.05 0 ÷ 25 ÷ 50
01426041 222A-1TQ 0.0005 2 2.02 • 0.05 0 ÷ 25 ÷ 50
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
MERCER Dial Gauges – TOP Quality
L series, 80 mm dial diameter, inch reading
ø82
19.2
15.7
ø8h6
M 2,5 - 6H
Permissible limits of a metrological characteristic (MPE/MPL)
ø4.5
ø5
20/19
ø3
6
10/9
ø6.4
60
98 / 117,2
158 / 228
1 in 2 in
0.0008 in 0.001 in
0.001 in 0.0012 in
0.00015 in 0.00015 in
0.0002 in 0.0002 in
≤ 2.2 N ≤ 2.5 N
✓
Factory
standard
0.0005 in
0.0001 in
1,5 mm
Rotating dial.
Can be locked.
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
High perfor mance
shock proof system
in both directions
Adjustable
tolerance markers.
Measuring insert
with a M2.5 thread.
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity

✓
Factory
standard
0.001 in
0.0005 in
0.0001 in
0.001 in: 2,2 mm
0.0005 in: 3,1 mm
0.0001 in: 1,1 mm
Rotating dial.
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Adjustable
tolerance markers.
Measuring insert
with a M2.5 thread.
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity
Models to 0.001, 0.0005 and 0.0001 in
Standard line
29
48.4
37
6
6.5 14.5
in in in in
01426010 181-1 0.001 0.200 0.212 – • 0.1 0 ÷ 50 ÷ 0
01426011 182-1 0.001 0.200 0.212 – • 0.1 0 ÷ 50 ÷ 100
01426012 183-1 0.0005 0.200 0.212 • • 0.05 0 ÷ 25 ÷ 0
01426013 184-1 0.0005 0.200 0.212 • • 0.05 0 ÷ 25 ÷ 50
354A 0.0005 0.200 0.212 • – 0.02 0 ÷ 10 ÷ 20
Standard line IP54 protected against the penetration of liquids
354AE 0.0005 0.200 0.212 • – 0.02 0 ÷ 10 ÷ 20
355AE 0.0001 0.120 0.130 • – 0.01 0 ÷ 5 ÷ 10
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force Standard line
Standard line IP54
D I A L G A U G E S
TESA YE, MERCER and COMPAC
Precision Dial Gauges – Standard
40 mm dial diameter, inch reading
ø37
ø3
ø10
ø8 h6
Permissible limits of a metrological characteristic (MPE/MPL)
ø4
ø5
ø40
(77.4)
0.001 in 0.0005 in 0.0001 in
0.0005 in 0.0005 in 0.0004 in
0.0006 in 0.0006 in 0.0005 in
0.00015 in 0.00015 in 0.00006 in
0.00015 in 0.00015 in 0.00008 in
≤ 1.4 N ≤ 1.4 N ≤ 1.7 N
≤ 1.7 N ≤ 2 N
57
37 30
ø37
6
ø3
6.5 14.5
ø10
ø5
ø8 h6
ø40
A-33 E-33

E-34
Models to 0.001, 0.0005 and 0.0001 in
Standard line
ø8 h6
in in in in
01426026 210-1 0.001 0.400 0.420 – • 0.1 0 ÷ 50 ÷ 0
01426027 211-1 0.001 0.400 0.420 – • 0.1 0 ÷ 50 ÷ 100
01426020 212-1 0.0005 0.400 0.420 – • 0.05 0 ÷ 25 ÷ 0
01426021 213-1 0.0005 0.400 0.420 – • 0.05 0 ÷ 25 ÷ 50
01426028 240-1 0.0001 0.200 0.210 – • 0.01 0 ÷ 50 ÷ 0
01426029 241-1 0.0001 0.200 0.210 – • 0.01 0 ÷ 50 ÷ 100
Standard line IP54 protected against the penetration of liquids
555AE 0.0001 0.200 0.210 • – 0.01 0 ÷ 5 ÷ 10
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
(105)
6
15.7
ø4.5
Measuring force Standard line
Standard line IP54
ø58
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
58 mm dial diameter, inch reading
Permissible limits of a metrological characteristic (MPE/MPL)
ø5
ø10
9
ø3
ø53
50
43
62
ø8 h6
0.001 in 0.00005 in 0.0001 in
0.0006 in 0.0006 in 0.0005 in
0.0007 in 0.0007 in 0.00055 in
0.0002 in 0.0002 in 0.00006 in
0.0002 in 0.0002 in 0.00008 in
≤ 1.4 N ≤ 1.4 N ≤ 1.7 N
≤ 2 N
(129)
ø58
6
15.7
ø5
10
ø3
ø53
50
57.5
71.5
✓
Factory
standard
0.001 in
0.0005 in
0.0001 in
0.001 in: 2,2 mm
0.0005 in: 3,1 mm
0.0001 in: 1,1 mm
Rotating dial.
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Adjustable
tolerance markers.
Measuring insert
with a M2.5 thread.
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity

✓
Factory
standard
0.001 in
0.0005 in
1,5 mm
Rotating dial.
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Adjustable
tolerance markers.
Measuring insert
with a M2.5 thread.
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity
Models to 0.001 in and 0.0005 in
Standard line
in in in in
01426031 216-1 0.001 1 1.2 • • 0.1 0 ÷ 50 ÷ 100
01426032 217-1 0.0005 1 1.2 • • 0.05 0 ÷ 25 ÷ 50
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Measuring force
D I A L G A U G E S
TESA YE, MERCER and COMPAC Dial Gauges –
Standard
58 mm dial diameter, inch reading, long range
Maximum permissible errors for a metrological characteristic (MPE)
ø58
ø8h6
M 2,5 - 6H
15.7
ø4.5
ø5
20
6
10
ø6.4
0.001 in 0.0005 in
0.0008 in 0.0008 in
0.001 in 0.001 in
0.00015 in 0.00015 in
0.0002 in 0.0002 in
≤ 2.2 N ≤ 2.2 N
ø3
50
88
148
A-35 E-35

E-36
Models to 0.001 or 0.0001 in
Standard line
ø 8,00
ø 7,95
3,18
ø 7,95
10 BA
27
ø 28,6
11,3
ø 3,9
9,52
5,61
4,19
15,91 9,39
11,15 7,95
in in in in N
01426050 71 0.001 0.04 0.05 – 0.04 0 ÷ 20 ÷ 0 ≤ 1,5
01426051 73 0.0001 0.01 0.05 – 0.01 0 ÷ 5 ÷ 0 ≤ 1,5
Models to 0,01 or 0,002 mm
Standard line
mm mm mm mm N
01416050 72 0,01 1 1,2 – 1 0 ÷ 50 ÷ 0 ≤ 1,5
01416051 74 0,002 0,2 1,2 – 0,2 0 ÷ 10 ÷ 0 ≤ 1,5
ø 3
ø 1,6
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Accessories for MERCER dial gauges, series 70
10BA coupling thread
3,6 3,2
10 BA
Standard insert with spherical measuring
faces.
03560072 Steel
mm
1,6
03560073 Carbide 1,6
D I A L G A U G E S
MERCER Precision Dial Gauges – Standard
Series 70, dial diameter to 1 1 /8 in or 29 mm
Permissible limits of a metrological characteristic (MPE/MPL)
0.001 in 0.0001 in 0,01 mm 0,002 mm
0.0005 in 0.0005 in 10 µm 6 µm
0.0008 in 0.0007 in 13 µm 9 µm
0.0003 in 0.0002 in 3 µm 2 µm
0.0003 in 0.0002 in 3 µm 3 µm
1,59 3,18
ø 4,76
10 BA
Measuring insert with a flat measuring
face.
03560074 Steel
mm
4,76
ø 3
10 BA
ø 3
ø 29,6
30
18,7
33,6
Dim. L 3,2
10 BA
mm
03560075 12,7
03560076 19,05
03560077 25,4
✓
Factory standard
or EN ISO 463
for metric models
See table
opposite
2,25 mm or
0,9 mm
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel
Without
shock proof
mechanism
Back with
central lug.
Measuring
insert with a 10BA thread.
Extensions for measuring inserts.
See in the
table opposite
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity

✓
Factory standard
or EN ISO 463 for
metric models
0.001 in and
0,01 mm
2,4 mm or
1,2 mm
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Without
shock proof
mechanism
Measuring insert
with a M2,5 thread.
Also with a
6,35 mm dia. holding rod
that can be unscrewed.
See table
opposite
Mounted insert
with a 3 mm dia.
steel ball tip
Cardboard box
Identification
number
Declaration
of conformity
✓
Models to 0.001 in
Standard line
in in in in N
01426060 91 0.001 0.05 0.14 – 0.05 0 ÷ 25 ÷ 0 ≤1,5
01426061 92 0.001 0.05 0.14 – 0.05 0 ÷ 25 ÷ 50 ≤1,5
Models to 0,01 mm
Standard line
mm mm mm mm N
01416060 93 0,01 1 3,5 – 1 0 ÷ 50 ÷ 0 ≤1,5
01416061 94 0,01 1 3,5 – 1 0 ÷ 50 ÷ 100 ≤1,5
Maximum permissible errors
for a metrological characteristic (MPE)
Deviation span
Total deviation span
Repeatability limit
Max. hysteresis
Accessories for MERCER dial gauges,
series 90
Swivelling arm
Amplification
03560078 1 : 1
D I A L G A U G E S
MERCER Precision Dial Gauges – Standard
Series 90, dial diameter to 1 1 /2 in or 38 mm,
back mounted plunger
103,5 3,96
0.001 in 0,01 mm
0.0010 in 25 µm
0.0015 in 40 µm
0.0005 in 12 µm
0.0005 in 12 µm
ø 6,35
2 BA
ø 3,18
18
ø 29,1
M 2,5 - 6H
ø 5
4,8
ø 7,98
ø 7,96
14,32
14,75
24
48,5
48,5 48,5
57,1
4,5
17,2
ø 4,6
ø 8
ø 38,1
22,5
18,45
A-37 E-37

E-38
62.5
21.3 32
6 3.2
Ø 40
Ø 25 h6
Ø 37
D I A L G A U G E S
C0MPAC Dial Gauges
40 mm dial diameter, back mounted plunger
Ø 3
Ø 8 h6
Ø 4
7
mm mm mm mm µm µm µm N
CP 352 0,01 3 3,2 1 0÷50÷100 14 3 3 0,9
CP 352S 0,01 ± 0,4 3,2 (1) 40÷0÷40 9 3 3 0,9
CP 353 0,01 3 3,2 0,5 0÷25÷50 14 3 3 0,9
CP 355 0,002 3 3,2 0,2 0÷10÷20 14 2 2,5 0,9
CP 355S 0,002 ± 0,08 3,2 (0,2) 8÷0÷8 9 2 2,5 0,9
S: Models with a reduced range of indication.
Since the pointer travels less than one revolution, all reading errors due to the revolution counter are eliminated.
✓
EN ISO 463
Factory
standard
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Shock proof
system to protect
the movement
Adjustable
tolerance
markers.
Measuring insert with a
M2,5 coupling thread.
Fastening sleeve with a
8h6 or 25h6 stem diameter.
Mounted insert
with a 3 mm
ball tip dia.
Cardboard box
Serial number
Inspection report
with a declaration
of conformity

✓
Factory standard
Rotating dial
Full-metal
housing.
Plunger and
8h6 dia. stem in stainless
steel, hardened and
ground.
Shock proof
system to protect
the movement
Adjustable
tolerance markers
on models with
a 58 mm dial diameter.
Measuring insert with a
M2,5 couling thread. Also
with revolution counter.
Mounted insert
with a 3 mm dia.
steel ball tip.
Electrical contacts
accurate to
0,001 mm.
Power supply:
10 µA, 12 V.
Response time: 0,1 s.
Cardboard box
Serial number
Declaration of
conformity
Metric models
109
6
80
Ø 10
Ø 8 h6
Ø 4.5
Ø 5
43
66
55
Ø 53
38.5
22.8 15.7
mm mm mm mm* µm µm µm N
CL2532 0,01 58 3 0,5 ÷ 1,5 0 ÷ 50 ÷ 100 17 3 3 ≤1,5
CL2532G 0,01 82 3 0,5 ÷ 1,5 0 ÷ 50 ÷ 100 17 3 3 ≤1,5
CL2555 0,002 58 3 0,5 ÷ 1,5 0 ÷ 10 ÷ 20 14 1,5 2 ≤1,5
CL2556 0,001 58 3 0,5 ÷ 1,5 0 ÷ 10 ÷ 20 14 1,5 2 ≤1,5
Inch models
in mm in in* in in in N
CL2533A 0.0005 58 0.120 0.020 ÷ .060 0 ÷ 25 ÷ 50 0.0007 0.00015 0.00015 ≤1,5
CL2555A 0.0001 58 0.120 0.020 ÷ .060 0 ÷ 5 ÷ 10 0.00055 0.00006 0.00008 ≤1,5
* Setting limit values
D I A L G A U G E S
COMPAC Dial Gauges
with electrical contacts, type CL
Type CL2
Mechanical dial gauge fitted with 2 electrical contacts. Can be used in
conjunction with the COMPAC amplifying unit R43 (No. 044285).
Ø 3
Ø 58
A-39 E-39

E-40
mm mm mm mN
Range for
zero setting
mm
01410420 MCA8-1-500 0,0005 0,05 3 500 25 ÷ 0 ÷ 25 ± 0,003
01410421 MCA8-1-150 0,0005 0,05 3 150 25 ÷ 0 ÷ 25 ± 0,003
01410422 MCA8-1-300 0,0005 0,05 3 300 25 ÷ 0 ÷ 25 ± 0,003
70
01410423 MCA8-2-500 0,001 0,1 3 500 50 ÷ 0 ÷ 50 ± 0,006
01410425 MCA8-2-150 0,001 0,1 3 150 50 ÷ 0 ÷ 50 ± 0,006
01410426 MCA8-2-300 0,001 0,1 3 300 50 ÷ 0 ÷ 50 ± 0,006
01410427 MCA8-3-500 0,002 0,2 3 500 100 ÷ 0 ÷ 100 ± 0,012
01410428 MCA8-3-150 0,002 0,2 3 150 100 ÷ 0 ÷ 100 ± 0,012
01410429 MCA8-3-300 0,002 0,2 3 300 100 ÷ 0 ÷ 100 ± 0,012
Lateral model
01410424 MCA8-2-L 0,001 0,1 3 500 50 ÷ 0 ÷ 50 ± 0,006
Accessory
20 31
4
62
31
ø 8 h6
ø 4 h5
P R E C I S I O N I N D I C A T O R S
TESA CARY Microcomparators MCA-8
The absolute precision
Specially designed for high precision measurement by comparison
(from ±0,8 µm) – Ideal for checking axial and radial runouts with
a very low hysteresis (from 0,3 µm).
• TESA CARY precision mechanism mounted parallel to the measuring
axis in compliance with the Abbe principle.
• Streamlined steel case with high rigidity.
• High precision throughout the measuring travel (from 0,8 µm).
• Very low measuring force (from 150 mN).
• Non-rotating dial. Quickly set to zero by moving the pointer with
just a thumb grip.
• Low sensitivity to temperature variations.
On request Sealing bellow (to be specified when ordering)
Maximum permissible errors
Max. perm. errors,
Gges
Repeatability
limit, r
Max.
hysteresis, fu
0,0005 mm 0,001 mm 0,002 mm
0,8 µm 0,8 µm 1,0 µm
0,4 µm 0,3 µm 0,3 µm
0,3 µm 0,3 µm 0,3 µm
✓
DIN 879
Non-rotating dial
Fine setting by
moving the pointer
Metal
housing.
Stainless steel
plunger, hardened.
Adjustable
tolerance markers
Measuring insert
with a M2,5 thread
Mounted insert
with a 3 mm dia.
steel ball tip
110 g
Plastic case
Identification
number
Inspection report
with a declaration
of conformity

✓
DIN 879-1.
All sizes as per
EN ISO 463
Ball-bearing
plunger,
except for the
metric model to 0,01 mm
mounted on a plain
bearing
Metal
case
housing.
Plunger made from hardened
stainless steel
Adjustable
tolerance
markers.
Coupling thread for the
lifting cable.
M2,5 thread for the
measuring insert.
≈ 1 N
1 mounted
insert with
a 3,175 mm
diameter steel ball tip along
with 1 lifting cable
Suited
plastic case
Declaration
of conformity
Regular models
mm mm mm mm
0141761371 0,01 0,5 2,5 62 • 25 ÷ 0 ÷ 25
01419051 0141761373 0,001 0,1 3,0 62 • 50 ÷ 0 ÷ 50
Model IP54 protected against the penetration of liquids
01419052 0,001 0,1 3,0 62 • 50 ÷ 0 ÷ 50
Maximum permissible errors
Max. perm. errors
in one direction throughout
the measuring range, Ge
over any local
measuring range including
10 scale divisions, Gt
in both measuring directions
throughout the measuring
range, Gges
Repeatability limit, rw
Max. hysteresis, fu
P R E C I S I O N I N D I C A T O R S
ETALON Basic and ROCH
Precision Indicators
0,01 mm or 0,001 mm reading
Remarkably reliable, even when constantly used for series inspection –
Specially made for comparative measurements demanding a very low
measurement uncertainty – Measure axial and radial runouts with
the lowest hysteresis.
• Shock proof movement with gear-lever transmission and
long dead travel.
• Large, non-dazzling dial for easy readout.
• No coarse reading errors as the measuring travel is limited
to less than one revolution.
• Fine adjustment and protective knob to prevent unintentional
pointer displacement.
0,01 mm 0,001 mm
10 µm 1 µm
7 µm 0,7 µm
12 µm 1,2 µm
5 µm 0,5 µm
5 µm 0,5 µm
ø8 h6
ø4
9
23
6
R31
18
72,5
108
A-41 E-41

mm mm mm mm N
01419047 0,01 5 40 • 0,5 0 ÷ 25 ÷ 50 ≈1
01419048 0,01 10 58 – 1 0 ÷ 50 ÷ 100 ≈1
01419049 0,01 30 58 • 1 0 ÷ 50 ÷ 100 1,5 ÷ 2
01419050 0,01 50 58 • 1 0 ÷ 50 ÷ 100 1,5 ÷ 2
Plunger retraction device
01462003 Lift lever
Backs with permanent magnet or central lug, see page E-47.
ø8 h6
ø4
7
Deviation span
Deviation span within the local
measuring span of 0,1 mm
20,5
Repeatability limit
6
12 ø40
48
74,5
D I A L G A U G E S
ETALON Basic Dial Gauges
0,01 mm reading
Regular and long range models
Maximum permissible errors for a metrological characteristic (MPE)
ø8 h6
mm 5 10 30 50
µm 12 15 20 25
µm 6 8 9 12
µm 3 3 3 3
E-42 01419047 01419048 01419049 - 01419050
7,5
ø4
22,5
ø58
18
6
69
105
8/11
7,5
ø8 h6
ø5
22,5
ø58
19 / 36
35 / 55
6
89 / 127
148 / 232
✓
EN ISO 463
Factory
standard
0,01 mm
Dial diameter 40
or 58 mm: 2,2 or
1,5 mm, resp.
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
With or without
shock proof
mechanism
Adjustable
tolerance
markers.
Measuring insert with
a M2.5 thread.
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Plastic case or
cardboard box
Identification
number
Declaration
of conformity

✓
EN ISO 463
Factory
stsandard
0,01 mm
2,2 mm
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
With or without
shock proof
mechanism
Adjustable
tolerance
markers.
Measuring insert with
a M2.5 thread.
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Plastic case or
cardboard box
Identification
number
Declaration
of conformity
ø 40
1
Regular models
mm mm mm mm N
0141760560 0,01 3 3,4 – 0,5 0 ÷ 25 ÷ 50* ≤1,4
0141760561 0,01 3 3,4 – 0,5 0 ÷ 25 ÷ 50* ≤1,4
0141760582 0,01 5 5,4 • 0,5 0 ÷ 25 ÷ 50* ≤1,4
Model with restricted reading range
0141760551 0,01 0,4 4,5 • 20 ÷ 0 ÷ 20 ≤1,4
Model IP54 protected against the penetration of liquids
0141760570 0,01 3 3,4 0,5 0 ÷ 25 ÷ 50* ≤ 2
• * With extra red tinted reverse numbering.
6,5
21
11,5
ø 8
M 2,5 - 6H
ø 4
7
7
11,5 / 8
ø 37
15,5
6 8
(78 / 74,5)
0141760560
0141760561
ø 40
1
6,5
21
11,5
ø 8
ø 8
M 2,5 - 6H
ø 4
7
7
16,5
ø 37
15,5
6 8
(83)
ø 40
13 1
5,2
ø 8 h6
6 15 15,5 ø 37 13,5
(87)
0141760551
M 2,5
0141760582 0141760570
0,01 mm ≤ 0,8 mm 3 mm 5 mm 10 mm
Deviation span
Deviation span within the local
7 µm 10 µm 12 µm 15 µm
measuring span of 0,1 mm
5 µm 5 µm 5 µm 5 µm
Total deviation span
9 µm 12 µm 14 µm 17 µm
Repeatability limit
Max. hysteresis
D I A L G A U G E S
ROCH Precision Dial Gauges
0,01 mm reading
Models C 40
The dial gauge N o 0141760560 is the perfect low-cost model.
Maximum permissible errors for a metrological characteristic (MPE)
3 µm 3 µm 3 µm 3 µm
3 µm 3 µm 3 µm 3 µm
7
7
A-43 E-43

E-44
ø 58
1
33
Regular models
0141760631 – 0141760635
0141760632 – 0141760636
mm mm mm mm mm N
0141760631 58 0,01 10 10,5 – 1 0 ÷ 50 ÷ 100* ≤ 1,4
0141760632 58 0,01 10 10,5 – 1 0 ÷ 50 ÷ 100* ≤ 1,4
0141760635 58 0,01 10 10,5 – 1 0 ÷ 50 ÷ 100* ≤ 1,4
0141760636** 58 0,01 10 10,5 – 1 0 ÷ 50 ÷ 100* ≤ 1,4
0141760640 58 0,01 10 10,5 • 1 0 ÷ 50 ÷ 100* ≤ 1,4
0141761210 60,4 0,01 10 10,5 • 1 0 ÷ 50 ÷ 100* ≤ 1,4
0141761211** 60,4 0,01 10 10,5 • 1 0 ÷ 50 ÷ 100* ≤ 1,4
Model with restricted reading range
0141760601 58 0,01 ±0,4 9,0 • 40 ÷ 0 ÷ 40 ≤ 1,4
Model IP54 protected against the penetration of liquids
0141760624 58 0,01
* With extra red tinted reverse numbering.
10 10,5 • 1 0 ÷ 50 ÷ 100* ≤ 2
** With mounted central lug back No. 0351669012 (also refer to page E-47).
16,5
7,5
ø 8
ø 4
M 2,5 - 6H
7,5
10 / 13
7,5
ø 52
22
15
6
(108 / 105)
ø 60,4
40,8
21,5
ø 4
M 2,5 - 6H
24
0141761210
0141761211
9
D I A L G A U G E S
ROCH Precision Dial Gauges
0,01 mm reading
Models C 58 and C 60
Both models No. 0141760635 and 0141760636 are particularly profitable.
ø 54
ø 8 h6
8
116
ø 58
1
33
16,5
0141760601
0141760640
7,5
ø8
ø 8
ø 4
M 2,5 - 6H
7,5
25
7,5
ø 52
22
15
6
(120)
ø 58
1
18
7,5
ø8
ø 8 h6
M 2,5
0141760624
7,5
25
7,5
ø 52
22
22
6
(127)
.
✓
EN ISO 463
Factory
standard
0,01 mm
1,5 mm
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
With or without
shock proof
mechanism
Adjustable
tolerance
markers.
Model No. 0141760640
with fine adjust mounted
under the protective cap
for dial reading.
Measuring insert with a
M2.5 thread.
For accuracy,
see table on
page E-43
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip.
Exceptions:
Models No. 0141760631,
0141761210, 0141761211
have a ruby ball tip.
Plastic case or
cardboard box
Identification
number
Declaration
of conformity

✓
EN ISO 463
Factory
standard
0,01 mm
2,2 mm
Rotating dial
Full-metal
case
housing.
Fixing shank and plunger in
hardened stainless steel
With or without
shock proof
mechanism
Adjustable
tolerance
markers.
Measuring insert with
a M2.5 thread.
Deviation
span:
15 µm.
Deviation span within the
local measuring span of
0,1 mm: 5 µm.
Total deviation span:
19 µm
3 µm
3 µm
See in the
table opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Cardboard box
Identification
number
Declaration
of conformity
Regular model
mm mm mm mm N
0141761221 0,01 10 10,4 – 1 0 ÷ 50 ÷ 100* ≤1,4
* With extra red tinted reverse numbering.
Regular models
D I A L G A U G E S
ROCH Precision Dial Gauges
0,01 mm reading
Model C 80
mm mm mm mm mm N
0141761213
0141761214**
0141760651
60,4
60,4
58
0,01
0,01
0,01
15
15
30
15,5
15,5
30,5
•
•– 1
1
1
0 ÷ 50 ÷ 100*
0 ÷ 50 ÷ 100*
0 ÷ 50 ÷ 100
≤1,6
≤1,6
≤1,6
0141760652***
0141760653
0141760661
58
58
58
0,01
0,01
0,01
30
30
50
30,5
30,5
51
–
•– 1
1
1
0 ÷ 50 ÷ 100
0 ÷ 50 ÷ 100
0 ÷ 50 ÷ 100
≤1,6
≤1,6
≤ 2,2
0141760662***
0141760663
0141760671
58
58
58
0,01
0,01
0,01
50
50
80
51
51
81
–
•– 1
1
1
0 ÷ 50 ÷ 100
0 ÷ 50 ÷ 100
0 ÷ 50 ÷ 100
≤2,2
≤2,2
≤ 3,0
0141761224 80 0,01 100 100,5 – 1 0 ÷ 50 ÷ 100 ≤ 3,5
* With extra red tinted reverse numbering.
** With mounted central lug back No. 0351669012 (also report to page E-47).
*** Counterclockwise numbering.
ø 80
30
17
9,5
ø 8
ø 4
M 2,5 - 6H
ROCH Precision Dial Gauges with a Long Range,
0,01 mm reading
Models C 58, C 60 and C 80
7,5
13
7,5
51
26
20
12
6
(128)
A-45 E-45

E-46
ø 60,4
40,8
21,5
ø 4
M 2,5 - 6H
24
0141761213
0141761214
9
ø 54
ø 8 h6
8
116
ø 58
91,5
35
7,8
ø 11
ø 8
ø 5
M 2,5 - 6H
7,5
7,5
75,5
ø 59
36,5
55
6
0141760651 – 0141760652
0141760653
(232)
7,8
0141760661 – 0141760663
0141760662 – 0141760671
0141761224
0,01 mm ≤ 30 mm 50 mm 80 mm 100 mm
Deviation span
Deviation span within the local
20 µm 25 µm 30 µm 35 µm
measuring span of 0,1 mm
5 µm 5 µm 5 µm 8 µm
Repeatability limit
D I A L G A U G E S
ø 58
141,5
55
ø 11
ø 8
ø 5
M 2,5 - 6H
7,5
7,5
105,5
ø 59
56,5
85
6
(312)
ø 80
172
64,5
9,5
ø 13
M 2,5 - 6H
Maximum permissible errors for a metrological characteristic (MPE)
ø 10
ø 6
7,5
8,5
128,5
71
70,5
106
6
3 µm 3 µm 3 µm 8 µm
(382)
✓
EN ISO 463
Factory standard
0,01 mm
1,5 mm
(C 58 or C 60)
2,2 mm
(C 80)
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
With or without
shock proof
system
Adjustable
tolerance
markers.
Measuring insert with
a M2.5 thread.
In order
to eliminate
any hysteresis
when measuring with
the plunger moving
downward, this feature
has to be coupled on
the measuring points,
directly.
See table
on the previous
page E-45
Mounted insert
with a 3,175 mm
dia. steel ball tip.
Exceptions:
Models No. 0141761213
and 0141761214 fitted with
a ruby ball tip
Cardboard box
Identification
number
Declaration
of conformity

✓
EN ISO 463
Factory
standard
0,001 mm
1,1 mm
(0141761261)
2,2 mm
(0141761262)
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
With shock proof
mechanism
Adjustable
tolerance
markers.
Measuring insert with
a M2.5 thread.
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Suited
plastic case
Identification
number
Declaration
of conformity
mm mm mm mm N
Regular models
0141761261 0,001 1 1,1 0,2 0 ÷ 100/0 ÷ 100* ≤ 1,5
• 0141761262 0,001 1 1,1 0,1 0 ÷ 50 ÷ 100* ≤ 1,2
• * With extra red tinted reverse numbering.
01462004 40 mm 34 mm
01462005 58, 60, 80 mm 46 mm
ø 40
1
6,5
21
11,5
ø8
ø 8
M 2,5 - 6H
ø 4
Maximum permissible errors
for a metrological characteristic (MPE)
0,001 mm 1 mm
Deviation span
Deviation span within the local
5 µm
measuring span of 0,01 mm
3 µm
Total deviation span
7 µm
Repeatability limit
Max. hysteresis max.
Central lug backs
7
7
3 µm
3 µm
L mm
01462000 40 mm 34 mm 34 mm 14,5 mm
01462001 58, 60, 80 mm 46 mm 46 mm 17 mm
13,5
ø 37
15,5
6 8
Bezel Back Magnetic
diameter diameter face
Magnetic backs with permanent magnets
ROCH Precision Dial Gauges
0,001 mm reading
Models C 40
Backs for ROCH or ETALON Basic
Precision Dial Gauges
D I A L G A U G E S
(80)
ø 40
1
6,5
21
11,5
ø 8
M 2,5 - 6H
ø 4
7
ø9
34
46
5
7
L
10,5
ø 37
15,5
6 8
ø
(77)
13
21
ø 5
A-47 E-47
16

E-48
ø 58
1
33
Regular models
16,5
7,8
ø 8
ø 8
ø 4
M 2,5 - 6H
7,5
7,5
13 / 17
ø 52
22
15
6
108 / 112
ø 58
1
33
16,5
7,8
ø 9
ø 8
ø 4
M 2,5 - 6H
7,5
7,5
17
ø 52
22
15
6
D I A L G A U G E S
ROCH Precision Dial Gauges
0,001 mm reading
Models C 58 and C 80
mm mm mm mm mm N
0141761282 58 0,001 1 1,1 – 0,2 0 ÷ 100/0 ÷ 100* ≤ 1,5
0141761283 58 0,001 1 1,1 • 0,2 0 ÷ 100/0 ÷ 100* ≤ 1,5
0141761284 58 0,001 1 1,1 • 0,1 0 ÷ 50 ÷ 100* ≤ 1,5
0141761291 80 0,001 1 1,1 – 0,2 0 ÷ 100/0 ÷ 100* ≤ 2,5
Models IP54 protected against the penetration of liquids
0141761281 58 0,001 1 1,1 0,2 0 ÷ 100/0 ÷ 100* ≤ 2,0
• * With extra red tinted reverse numbering.
112
0141761282
0141761283 0141761284
0141761281
0141761291
ø 58
1
18
ø8
ø 8 h6
M 2,5
7,5
7,5 9,5
17
7,5
ø 52
22
22
6
(119)
ø 80
30
17
ø 8
ø 4
M 2,5 - 6H
7,5
13
7,5
51
26
20
12
6
(128)
✓
EN ISO 463
Factory
standard
0,001 mm
0,8 mm
(No. 0141761281,
0141761282
and 0141761283)
1,5 mm (No 0141761284
and 0141761291)
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
With or without
shock proof
system
Adjustable
tolerance
markers.
Measuring insert with
a M2.5 thread.
For accuracy, see
table on previous
page E-47
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Suited plastic case
Identification
number
Declaration
of conformity

✓
EN ISO 463
Factory standard
0,1 mm
1,1 mm (C 40)
1,5 mm (C 58)
2,2 mm (C 80)
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Without
shock proof
mechanism
Measuring
insert with a
M2,5 thread
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Suited
plastic case
Identification
number
Declaration
of conformity
ø 40
1
Regular models
0141760500
mm mm mm mm mm N
0141760500 40 0,1 10 10,5 – 10 0 ÷ 5 ÷ 10 ≤ 1,0
0141760501 58 0,1 10 10,5 – 10 0 ÷ 5 ÷ 10 ≤ 1,0
0141760502 58 0,1 20 20,5 – 10 0 ÷ 5 ÷ 10 ≤1,0
0141760503 58 0,1 30 30,5 – 10 0 ÷ 5 ÷ 10 ≤1,5
0141760513 80 0,1 30 30,5 – 10 0 ÷ 5 ÷ 10 ≤ 2,0
26
11,5
M 2,5 - 6H
6
ø 8
ø 4
7
7
11,5
ø 37
15,5
6 13
83
ø 58
1
33
16,5
7,5
ø 8
ø 5
M 2,5 - 6H
0141760501
Maximum permissible
errors for a metrological characteristic (MPE)
0,1 mm 10 mm
Deviation span
Deviation span within the local
40 µm
measuring span of 1 mm
25 µm
Total deviation span
55 µm
Repeatability limit
Max. hysteresis
7,5
D I A L G A U G E S
ROCH Precision Dial Gauges
0,01 mm reading
Models C 40, C 58 and C 80
13
7,5
ø 52
22
15
6
(108)
ø 58
1
43 / 53
16,5
15 µm
15 µm
7,5
ø 8
ø 5
M 2,5 - 6H
7,5
13 / 23
7,5
ø 52
22
25 / 35
6
(118 / 138)
0141760503
Same as model:
0141760502
ø 80
1
57
23,5
9,5
ø 8
ø 5
M 2,5 - 6H
7,5
23
7,5
ø 52
40
32
6
(153)
0141760513
A-49 E-49

E-50
Regular models
mm mm mm mm mm N
0141760566 40 0,01 3 3,5 – 0,5 0 ÷ 25 ÷ 50* ≤1,2
0141760611 58 0,01 5 5,5 – 1 0 ÷ 50 ÷ 100* ≤1,5
* With extra red tinted reverse numbering.
26 7
16,5
M 2,5 - 6H
ø 4
ø 40
ø 38
ø 34
ø 28
ø 8
13 6,5
18
8
6
66
26 7
16,5
M 2,5 - 6H
Maximum permissible errors for a metrological characteristic (MPE)
0,01 mm 3 mm 5 mm
Deviation span
Deviation span with the local
12 µm 17 µm
measuring span of 0,1 mm
5 µm 5 µm
Total deviation span
15 µm 20 µm
Repeatability limit
Max. hysteresis
D I A L G A U G E S
ROCH Precision Dial Gauges
0,01 mm reading
Models C 40 and C 58 with back mounted plunger
ø 4
ø 58
ø 28
ø 8
13 6,5
18
8
6
66
5 µm 5 µm
15 µm 15 µm
✓
EN ISO 463
Factory
standard
0,01 mm
2,2 mm (C 40)
1,5 mm (C 58)
Rotating dial
Full-metal
case housing.
Fixing shank and
plunger in hardened stainless
steel.
Without shock
proof system
Adjustable
tolerance
markers.
Measuring insert with
a M2,5 thread.
See table
opposite
Mounted insert
with a 3,175 mm
dia. steel ball tip
Cardboard box
Identification
number
Declaration
of conformity

✓
✓
6 5
R1,5 ø3
ø5
ø5
M2,5
03510001 Steel
L mm
6
03510002 Carbide 6
03560001 Sapphire 6
L
r 0,5
03560035 Steel
L mm
5
03560036 Steel
10
03560037 Steel
15
03560038 Steel
20
03560039 Steel
30
03560040 Steel
40
R5
Standard spherical measuring inserts.
Spherical measuring inserts,
R = 0,5 mm.
6
Spherical measuring inserts.
03510101 Steel
R mm
5
03510102 Carbide 5
A C C E S S O R I E S F O R D I A L G A U G E S A N D T H E L I K E
Measuring Inserts for Dial Gauges,
Axial Probes and other Hand-Held Tools
Executions with a M2,5 coupling thread
ø5
ø10
4 4,1
M2,5
5,4
Short spherical measuring insert.
03560007 Carbide
L mm
4
M2,5
18
D
Spherical measuring inserts.
03560051 Carbide
mm
1
03560052 Carbide 2
03560053 Carbide 3
03560054 Carbide 4
03560055 Carbide 5
03560056 Carbide 6
03560057 Carbide 7
03560058 Carbide 8
03560059 Carbide 9
03560060 Steel
10
03560061 Steel
11
03560062 Steel
12
6
r16
Spherical measuring inserts
03560017 Steel
R mm
16
03560018 Carbide 16
ø3
ø5
8
03560019 Steel
L mm
8
03560020 Carbide 8
03560021 Sapphire 8
R1,5
6,5
ø5
Long spherical measuring inserts.
ø1,5
16/26/36/46
9
Spherical measuring insert with
4 inter changeable pins, R = 1,5 mm.
03510201 Steel
L mm
16, 26, 36, 46
0,3 0,5
1,6
6
Measuring insert with offset (A)
contact point and lock nut for radial
alignment.
03510401 Steel
A mm
6,5
A-51 E-51

E-52
12
0,4
03560063 Steel
A mm
12
03560024 Steel
B mm
0,3
03560025 Carbide 0,3
03510602 Carbide
B mm
0,5
ø4
ø2,5
ø2
15
2,3
16
ø7
Measuring insert with offset (A)
contact point and lock nut for radial
alignment.
.
ø5
5 6,5
3,3
1
0,5
5
16
8
ø3.4 0.3
Measuring inserts with blade-shaped
measuring face. Lock nut for radial
alignment
A C C E S S O R I E S F O R D I A L G A U G E S A N D T H E L I K E
Insert with narrow, off-centre measuring
face.
Lock nut for radial alignment.
ø7,5
03560030
3,0
2,0
1.6
Insert with needle contact point.
L mm B mm
03560031 5 0,2
03560032 10 0,2
03560033 15 0,2
03560034 20 0,2
ø4
2,5
0,5
ø5
Steel
2,3
03510702 Carbide
B mm
0,5
16
03510902 Carbide
mm
2,5
L
8
0,2
ø2
Measuring inserts with blade-shaped
measuring face, in steel.
Lock nut for radial alignment.
ø7,5
Insert with a narrow, parallel adjustable
measuring face.
Lock nut for radial alignment.
Measuring insert with a flat, parallel
adjustable measuring face.
Lock nut for radial alignment.
øD
0,003
5
1,5
7
03560010
03560011
03510502
6
ø4
3,3
ø2
7,5
2,5
ø5
17,25
Measuring inserts with ball-bearing
rollers. Lock nut for radial alignment.
Shape
Steel cylindrical
Steel ball-shaped
Insert with a cylindrical measuring face.
Lock nut for radial alignment.
8
ø3,4
Ø 0,8
03510801 Steel
mm
2,5
03510802 Carbide 2,5
03560022 Steel 3,4
03560023 Carbide 3,4
03560081 Carbide 0,8
6
Carbide
Inserts with a flat measuring face.
11
6
M2,5

ø5
ø4
ø4
L mm L1 mm
03560026 5 2,8 2
03560027 10 7,8 2
03560028 15 12,8 2
03560029 20 17,8 2
M2,6
R1
R5
ø2
3
3
10
s = 3
s = 3
L1
Inside Outside
03560066 M2,5 M2,6
03560067 M2,5 M3
03560064 M2,6 M2,5
03560065 M3 M2,5
03560068 M2,5 6BA
03560069 M2,5 8BA
03560070 6BA M2,5
03560071 8BA M2,5
M2
M2
03510204 Carbide R 1
03510103 Carbide R 5
L
M2,5
ø5
Steel inserts with a flat measuring face.
Connectors for measuring inserts.
Executions with
a M2 Coupling Thread
Spherical measuring inserts.
M2 thread.
mm
A C C E S S O R I E S F O R D I A L G A U G E S A N D T H E L I K E
ø5
ø1,5
03560008 Steel 1,5
03560009 Carbide 1,5
L mm
03560042 10
03560043 15
03560044 20
03560045 25
03560046 30
03560047 35
03560048 40
03560049 45
03560050 50
R5
03510202 Carbide
L mm
16
03510203 Carbide 26
ø3,5
ø1.5
M2
L
20
ø3,5 L
L
8
5
s = 3
s = 3
ø5
Inserts with a flat measur ing face as
well as interchangeable pin.
Extensions for measuring inserts.
Spherical measuring inserts,
R = 5 mm. M2 thread.
M2
M2
ø5
M2,5
ø4
03560012 Steel
5
03560013 Carbide 5
03560014 Steel 10
03560015 Carbide 10
03560016 Steel 20
L mm
03540501 10
03540502 15
03540503 20
03540504 40
2,5
2
5
Inserts with a flat measuring face.
03510503
L
ø4
Extensions for measuring inserts.
6
s = 3
M2
Measuring insert with cylindrical
measuring face. Lock nut for radial
alignment. M2 thread.
L mm
03540505 10
03540506 15
6
Carbide
ø10
Extensions for measuring inserts, M2.
ø20 3,6 5
A-53 E-53

E-54
A C C E S S O R I E S F O R D I A L G A U G E S A N D T H E L I K E
Devices for Plunger Retraction
Top mounted retraction devices.
03560004 Retraction
device
mm
Ø 40
03560005 Retraction
device
Ø 58
Each consisting of:
03540104
03540101
03540102
01960005
03560006
03560012
Lift lever
Head screw
Bottom mounted retraction device.
Consisting of:
Retraction device
Lift lever
Washer
Bottom mounted lift lever.
90° Angle Probe
Furnished with:
90° angle probe used
for the transmission of
the plunger movement
up to 10 mm. Suited
for dial gauges with a
0,01 mm scale division.
Measuring insert with
a 5 mm diameter flat face
✓
✓

✓
Dull-chrome
plated, except
for models
No. 01460010,
01460011, 01460016 and
01460017
Holding force
= 150 N
A
B
C
A
6.3
6.3
6.3
A C C E S S O R I E S F O R D I A L G A U G E S A N D T H E L I K E
19
19
Backs for TESA YR and MERCER
Precision Dial Gauges in Standard or
TOP Quality Version
8.5
8.5
9
19
25
9
22.2
12.7
16
ø6.4
ø6.4
M6
ø8
ø6.4
ø18
25
Executions for dial gauges with a 40 mm dial diameter
01460008 A
01460009 B
01460010 C
01460011 D
01460012 E
15
6.3
21.7
D E
01460013 A
01460014 B
01460015 C
01460016 D
01460017 E
01460018 F
01460019 G
B C D
E F G
12.7
9
19
9
M6
M3 (4x)
Back with central lug
Back with offset lug
Back with a 8 mm dia. fixing shank
Back with M6 inner thread
Back with permanent magnet
ø18
Executions for dial gauges with a 58 or 82 mm dial diameter
ø6.4
37
37.5
27
Flat back
Flat back with central lug
Flat back with offset lug
Back with a 8 mm dia. fixing shank
Back with a M6 inner thread
Back with 4 clamping bores as per
CNOMO French standard
Back with permanent magnet
25.5
27
16
ø24
ø8
ø24
A-55 E-55