Xerox Document Centre 440/432/420 User Guide
Xerox Document Centre 440/432/420 User Guide Xerox Document Centre 440/432/420 User Guide
Code Description and Corrective Action 0223–0226 A communication error occurred. Check the telephone line, select Forced 4800 and begin again. 0227 Memory became full during communication. Check the available memory. Delete the job, divide it into smaller jobs and begin again. 022C–022D A communication error occurred. Begin again. 022E Check the password for the remote machine and begin again. 0230–0233 A communication error occurred. Check the available memory. Verify that the dial directory code contains a DTMF code after a secure code and begin again. 0250–0252 A communication error occurred. Contact the remote operator, check the telephone line and begin again. 0254 Operator error. The image size was changed to match the capability of the remote fax. 0255 Operator error. The resolution was changed to match the capability of the remote fax. 0291 An error occurred during diagnostics. Begin again. 0294 An error occurred during diagnostics. Begin again. 02A1–02A3 A communication error occurred. Begin again. 02D1–02D5 A transmission error occurred. Begin again. 0510–0542 A communication error occurred. Check the telephone line and the dial directory DTMF sequence and begin again. Page 12-16 Xerox Document Centre 440/432/420 User Guide
Code Description and Corrective Action 0545–056C Either a dial tone was not detected or the telephone circuit was busy. Check the telephone line and begin again. 056D The remote machine did not answer. Contact the remote operator and begin again. 056E The handset is off the hook. Reset the handset and begin again. 056F A communication error occurred. Check the telephone line and begin again. 0570 Check the ID of the remote machine and begin again. 0671 Repeat the job. 0573–057A Either the dial tone was not detected or the telephone circuit was busy. Check the telephone line and begin again. 057B A communication error occurred. Begin again. 057E–0589 Either the dial tone was not detected or the telephone circuit was busy. Check the telephone line and begin again. 05E0–0601 A communication error occurred. Begin again. Xerox Document Centre 440/432/420 User Guide Page 12-17 Problem Solving
- Page 327 and 328: � Access Auditron Setups. � Sel
- Page 329 and 330: � Select [Add Account]. � Enter
- Page 331 and 332: � Select [Job Completion Setup].
- Page 333 and 334: � Access Auditron Setups. � Sel
- Page 335 and 336: Monitor without limits to set the d
- Page 337 and 338: Auditron No Setups (DC420) No N/A Y
- Page 339 and 340: � If necessary, select [Additiona
- Page 341 and 342: Scan to File Setups Quick Pathway
- Page 343 and 344: Print Setups Quick Pathway �Selec
- Page 345 and 346: PCL Setups Allows the System Admini
- Page 347 and 348: 11 Maintenance There will be times
- Page 349 and 350: Cleaning the DC440/432/420 Proper m
- Page 351 and 352: Replacing the Copy/Print Cartridge
- Page 353 and 354: � To open the Duplex Module door,
- Page 355 and 356: � Using the handle, lift the cart
- Page 357 and 358: � Close the Left Front Cover. NOT
- Page 359 and 360: � The staple cartridge is located
- Page 361 and 362: Convenience Stapler (optional) �
- Page 363 and 364: 12 Problem Solving The DC440/432/42
- Page 365 and 366: Clearing Jams Media jams happen for
- Page 367 and 368: Symptom Recommendation The machine
- Page 369 and 370: Symptom Recommendation Paper someti
- Page 371 and 372: Symptom Recommendation Output is to
- Page 373 and 374: Symptom Recommendation Misfeeds in
- Page 375 and 376: Symptom Recommendation Can’t stor
- Page 377: Fault Codes and Messages Table of F
- Page 381 and 382: Call for Service procedure Xerox We
- Page 383 and 384: 13 Specifications The DC440/432/420
- Page 385 and 386: Copier Speed from paper tray 1 DC42
- Page 387 and 388: Bypass Tray Capacity: 50 sheets of
- Page 389 and 390: Electrical Voltage: 102-140VAC Powe
- Page 391 and 392: Long Document Send/Receive Send: 36
- Page 393 and 394: 14 Glossary This chapter contains a
- Page 395 and 396: Communication Mode (DC440/ 432) sel
- Page 397 and 398: Halftone gray patterns that are not
- Page 399 and 400: PDF Portable Document File. Peer-to
- Page 401 and 402: TIFF Tagged Image File Format Trans
- Page 403 and 404: 15 Index Numerics 2 up, copy 3-35 A
- Page 405 and 406: etrieving a copy job 3-51 storing a
- Page 407 and 408: finisher specifications 13-6 forced
- Page 409 and 410: original type, fax 4-9 other media
- Page 411 and 412: add/modify accounts (DC440/432) 10-
- Page 413 and 414: T pause (stop) button 2-22 power sa
Code Description and Corrective Action<br />
0223–0226 A communication error occurred. Check the<br />
telephone line, select Forced 4800 and begin<br />
again.<br />
0227 Memory became full during communication.<br />
Check the available memory. Delete the job,<br />
divide it into smaller jobs and begin again.<br />
022C–022D A communication error occurred. Begin again.<br />
022E Check the password for the remote machine<br />
and begin again.<br />
0230–0233 A communication error occurred. Check the<br />
available memory. Verify that the dial directory<br />
code contains a DTMF code after a secure code<br />
and begin again.<br />
0250–0252 A communication error occurred. Contact the<br />
remote operator, check the telephone line and<br />
begin again.<br />
0254 Operator error. The image size was changed to<br />
match the capability of the remote fax.<br />
0255 Operator error. The resolution was changed to<br />
match the capability of the remote fax.<br />
0291 An error occurred during diagnostics. Begin<br />
again.<br />
0294 An error occurred during diagnostics. Begin<br />
again.<br />
02A1–02A3 A communication error occurred. Begin again.<br />
02D1–02D5 A transmission error occurred. Begin again.<br />
0510–0542 A communication error occurred. Check the<br />
telephone line and the dial directory DTMF<br />
sequence and begin again.<br />
Page 12-16 <strong>Xerox</strong> <strong>Document</strong> <strong>Centre</strong> <strong>440</strong>/<strong>432</strong>/<strong>420</strong> <strong>User</strong> <strong>Guide</strong>