Xerox Document Centre 440/432/420 User Guide
Xerox Document Centre 440/432/420 User Guide Xerox Document Centre 440/432/420 User Guide
Lighter/Darker � Load the document. � Select [Added Features]. � Select [Lighter/Darker]. � Use the scroll bars to increase or decrease the image adjustment for the document. � Select [Save] and select [Start]. Communication Mode (DC440/432) � Load the document. � Select [Added Features]. � Select [Communications Mode]. � Select the required option. � Select [Save] and then [Start]. Adjusts the image quality of the document being scanned for fax transmissions. On the DC440/432 this feature allows selection of the communication mode used for transmission to a remote fax machine. NOTE: On the DC420 the Forced 4800 bps feature is the only available option. Page 4-22 Xerox Document Centre 440/432/420 User Guide
Delayed Start The following options are available: Super G3 determines the communication mode to be used based on the maximum capabilities of the remote fax machine. This mode minimizes data transmission errors by using Error Correction Mode (ECM). Initial communication speed will be 33,600 Bits Per Second (bps). G3 selects the communication mode based on the maximum capabilities of the remote fax machine. Initial communication speed will be 14,400 bps. ECM is also used with this option. Forced 4800 bps used in areas of low-quality communication, or when experiencing telephone noise, or when fax communications are susceptible to errors. To minimize errors, set the DC440/ 432/420 to run at a communication mode of 4800. This mode is slower, but it is less susceptible to errors. In some regional areas, the use of the Communication Mode/ Forced 4800 bps feature is restricted. Delayed Start is mainly used to transmit faxes during off-peak hours when telephone charges are lower or when sending to another country/time zone. Use Delayed Start, to transmit a document to a single destination, or use a broadcast send or polling operation. Up to 100 delayed send jobs can be programmed at one time, depending on the size of the documents and the available memory. Only one delayed poll can be saved at a time. Use the Fax Job Monitor feature to check the available memory. Xerox Document Centre 440/432/420 User Guide Page 4-23 Fax
- Page 83 and 84: Expert Image Quality � Select the
- Page 85 and 86: Edit (optional) Erase options Off n
- Page 87 and 88: Area Edit options Off the feature i
- Page 89 and 90: Output Format (Copy) Quick Pathway
- Page 91 and 92: N Up (2 Up - DC420) Transparency op
- Page 93 and 94: Annotation � Load the documents.
- Page 95 and 96: � If Off is selected, select comm
- Page 97 and 98: Inserts � Load the insert stock i
- Page 99 and 100: � After the last entry has been m
- Page 101 and 102: � Select either [Front Only] or [
- Page 103 and 104: Job Assembly (Copy) Build Job Quick
- Page 105 and 106: Stored Jobs � Program the job fea
- Page 107 and 108: � Select [Added Features] and the
- Page 109 and 110: Name the name of the job. For copy
- Page 111 and 112: Use the scroll buttons to move thro
- Page 113 and 114: 4 Fax Sending and receiving a facsi
- Page 115 and 116: 1. Select Features � If necessary
- Page 117 and 118: 3. Dial the number � Using the nu
- Page 119 and 120: The standard memory in the fax mach
- Page 121 and 122: Fine (200 x 200 dpi) recommended fo
- Page 123 and 124: Dialing � Enter the first fax num
- Page 125 and 126: Dial pause [-] to pause between num
- Page 127 and 128: Line 1 select this option if Line 1
- Page 129 and 130: To add numbers to the Current Dial
- Page 131 and 132: Added Features (Fax) Quick Pathway
- Page 133: Transmission Report � Load the do
- Page 137 and 138: Advanced Features (Fax) Quick Pathw
- Page 139 and 140: Poll Remote Fax NOTE: Build Job can
- Page 141 and 142: � Load the document. � Enter th
- Page 143 and 144: Fax Mailbox � Select [Added Featu
- Page 145 and 146: � Select [Added Features]. � Se
- Page 147 and 148: Reports & Setups (Fax) Quick Pathwa
- Page 149 and 150: Answer Mode � Select [Answer Mode
- Page 151 and 152: � Use the soft keypad to enter th
- Page 153 and 154: Maximum Store Width determines the
- Page 155 and 156: � Select [Dial Directory]. � Us
- Page 157 and 158: LAN Fax (Local Area Network Fax) LA
- Page 159 and 160: and is displayed on either the top
- Page 161 and 162: Type the job category, such as rece
- Page 163 and 164: 5 Media Print Media Print allows a
- Page 165 and 166: � Select [Media Print]. � Selec
- Page 167 and 168: 6 Scan to File The Scan option will
- Page 169 and 170: Scan to EMail (DC440/432) Quick Pat
- Page 171 and 172: Scan to File Quick Pathway �Selec
- Page 173 and 174: � Load the documents in the Docum
- Page 175 and 176: Added Features (Scan Setups) Quick
- Page 177 and 178: Basic Image Quality Adjusts the set
- Page 179 and 180: Reduce/Enlarge Adjusts the magnific
- Page 181 and 182: Erase Used to erase unwanted marks
- Page 183 and 184: Server IP Address /Server Name Docu
Lighter/Darker<br />
� Load the document.<br />
� Select [Added Features].<br />
� Select [Lighter/Darker].<br />
� Use the scroll bars to<br />
increase or decrease the<br />
image adjustment for the<br />
document.<br />
� Select [Save] and select<br />
[Start].<br />
Communication Mode (DC<strong>440</strong>/<strong>432</strong>)<br />
� Load the document.<br />
� Select [Added Features].<br />
� Select [Communications<br />
Mode].<br />
� Select the required option.<br />
� Select [Save] and then<br />
[Start].<br />
Adjusts the image quality of the document being scanned for<br />
fax transmissions.<br />
On the DC<strong>440</strong>/<strong>432</strong> this feature allows selection of the<br />
communication mode used for transmission to a remote fax<br />
machine.<br />
NOTE: On the DC<strong>420</strong> the Forced 4800 bps feature is the only<br />
available option.<br />
Page 4-22 <strong>Xerox</strong> <strong>Document</strong> <strong>Centre</strong> <strong>440</strong>/<strong>432</strong>/<strong>420</strong> <strong>User</strong> <strong>Guide</strong>