service manual sacd/dvd receiver - Diagramas Gratis - Diagramas ...

More documents

Recommendations

Info

HCD-S550/S880 3-14. PULLEY (RTR) ASSY 3-15. BELT (CK) 16 shaft (pulley (RTR) assy) 2 gear (L4) 3 torsion spring (L) front – bottom view – fig. 1 3 belt (CK) 5 pulley (LCG) hole A 1 two bushings (CDM72) 1 Rotate the pulley (RTR) assy in the direction of arrow A to disengage the shaft of the pulley (RTR) assy from the hole of the chassis (refer to fig. 1), and remove it. 2 gear (L5) 4 pulley (L5) pulley (RTR) assy B boss claw connector Tilting the pulley (RTR) assy in the direction of arrow B, move it over the claw and the connector of the chassis.
3-16. PULLEY (SPT) ASSY 2 pulley (SPT) assy 3 gear (S2) 3-17. BELT (CK), MOTOR (CK) ASSY (M751) 2 belt (CK) 3 pulley (CKG) 1 busing (CDM72) 4 two solders 5 two screws (BTP2.6 × 6) 4 torsion spring (S) 5 gear (SPT) 6 gear (KT) hole shaft (pulley (SPT) assy 7 motor (CK) assy (M751) 6 CK motor board HCD-S550/S880 1 Rotate the pulley (SPT) assy to fit position of the shaft to the hole of the chassis. 17
Page 1 and 2: SERVICE MANUAL Ver 1.6 2004.03 HCD-
Page 3 and 4: Notes on chip component replacement
Page 5 and 6: NOTES ON HANDLING THE OPTICAL PICK-
Page 7 and 8: Front Panel Display When playing ba
Page 9 and 10: • This set can be disassembled in
Page 11 and 12: 3-4. SEL BOARD 3-5. DVD BOARD 8 pow
Page 13 and 14: 3-8. POWER BOARD 3-9. AMP BOARD 3 c
Page 15: 3-12. HOLDER (AT) ASSY, RETAINER (C
Page 19 and 20: 4-3. HOW TO INSTALL ROTARY ENCODER
Page 21 and 22: 0-2-3. ROM Check Sum The revision n
Page 23 and 24: 2-1. Disc Type Disc Type Disc Type
Page 25 and 26: 2-7. Disc Check Memory Disc Check M
Page 27 and 28: 6. VERSION INFORMATION On the Test
Page 29 and 30: 7-2. BLOCK DIAGRAM - AUDIO (DSP) Se
Page 31 and 32: 7-4. BLOCK DIAGRAM - VIDEO Section
Page 33 and 34: 7-6. NOTE FOR PRINTED WIRING BOARDS
Page 35 and 36: 7-8. SCHEMATIC DIAGRAM - RF Section
Page 37 and 38: 7-10. SCHEMATIC DIAGRAM - MECHANISM
Page 39 and 40: 7-12. PRINTED WIRING BOARD - DVD Bo
Page 41 and 42: HCD-S550/S880 41 41 7-14. SCHEMATIC
Page 43 and 44: 7-16. SCHEMATIC DIAGRAM - DVD Board
Page 51 and 52: 7-24. PRINTED WIRING BOARDS - AMP S
Page 53 and 54: 7-26. SCHEMATIC DIAGRAM - AMP Secti
Page 55 and 56: 7-28. PRINTED WIRING BOARDS - I/O S
Page 57 and 58: 7-30. SCHEMATIC DIAGRAM - I/O Secti
Page 59 and 60: 7-32. SCHEMATIC DIAGRAM - DC-DC CON
Page 61 and 62: 7-34. SCHEMATIC DIAGRAM - CONTROL S
Page 63 and 64: 7-36. SCHEMATIC DIAGRAM - FL Board
Page 65 and 66: 7-38. PRINTED WIRING BOARDS - POWER
Page 67 and 68:
• Waveforms - RF Board - 1 IC001
Page 69 and 70:
eh IC206
Page 71 and 72:
- I/O Board - ya IC201 qf (X0) ys I
Page 73 and 74:
- RELAY Board - IC701, 711 BA6956AN
Page 75 and 76:
IC602 PCM1800E/2K SINGLE-END DEFERE
Page 77 and 78:
IC612 CXD9633Q VDD6 DSBCKF DSIFL 63
Page 79 and 80:
IC814 TC7WH157FK (TE85R) A 1 B 2 Y
Page 81 and 82:
- I/O Board - IC201 BU1924F-E2 (AEP
Page 83 and 84:
- POWER Board - IC901 STR-F6238 (Me
Page 85 and 86:
Pin No. Pin Name I/O Description 53
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
• DVD BOARD IC701 CXD1882R (DVD D
Page 93 and 94:
Page 95 and 96:
• DVD BOARD IC801 CXD2752R (DSD D
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
• DVD BOARD IC902 PT3000 (MECHANI
Page 103 and 104:
8-2. FRONT PANEL SECTION-1 not supp
Page 105 and 106:
8-4. CHASSIS SECTION-1 mechanism de
Page 107 and 108:
8-6. CHASSIS SECTION-3 F901 not sup
Page 109 and 110:
8-8. MECHANISM DECK SECTION-1 (CDM7
Page 111 and 112:
8-10. MECHANISM DECK SECTION-3 (CDM
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
NOTE: • Due to standardization, r
Page 119 and 120:
Ref. No. Part No. Description Remar
Page 121 and 122:
HCD-S550/S880 CONTROL DDCON DVD Ref
Page 123 and 124:
Page 125 and 126:
HCD-S550/S880 Ref. No. Part No. Des
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
HCD-S550/S880 Ref. No. Part No. Des
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
show all

service manual sacd/dvd receiver - Diagramas Gratis - Diagramas ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?