service manual sacd/dvd receiver - Diagramas Gratis - Diagramas ...
service manual sacd/dvd receiver - Diagramas Gratis - Diagramas ... service manual sacd/dvd receiver - Diagramas Gratis - Diagramas ...
HCD-S550/S880 3-14. PULLEY (RTR) ASSY 3-15. BELT (CK) 16 shaft (pulley (RTR) assy) 2 gear (L4) 3 torsion spring (L) front – bottom view – fig. 1 3 belt (CK) 5 pulley (LCG) hole A 1 two bushings (CDM72) 1 Rotate the pulley (RTR) assy in the direction of arrow A to disengage the shaft of the pulley (RTR) assy from the hole of the chassis (refer to fig. 1), and remove it. 2 gear (L5) 4 pulley (L5) pulley (RTR) assy B boss claw connector Tilting the pulley (RTR) assy in the direction of arrow B, move it over the claw and the connector of the chassis.
3-16. PULLEY (SPT) ASSY 2 pulley (SPT) assy 3 gear (S2) 3-17. BELT (CK), MOTOR (CK) ASSY (M751) 2 belt (CK) 3 pulley (CKG) 1 busing (CDM72) 4 two solders 5 two screws (BTP2.6 × 6) 4 torsion spring (S) 5 gear (SPT) 6 gear (KT) hole shaft (pulley (SPT) assy 7 motor (CK) assy (M751) 6 CK motor board HCD-S550/S880 1 Rotate the pulley (SPT) assy to fit position of the shaft to the hole of the chassis. 17
- Page 1 and 2: SERVICE MANUAL Ver 1.6 2004.03 HCD-
- Page 3 and 4: Notes on chip component replacement
- Page 5 and 6: NOTES ON HANDLING THE OPTICAL PICK-
- Page 7 and 8: Front Panel Display When playing ba
- Page 9 and 10: • This set can be disassembled in
- Page 11 and 12: 3-4. SEL BOARD 3-5. DVD BOARD 8 pow
- Page 13 and 14: 3-8. POWER BOARD 3-9. AMP BOARD 3 c
- Page 15: 3-12. HOLDER (AT) ASSY, RETAINER (C
- Page 19 and 20: 4-3. HOW TO INSTALL ROTARY ENCODER
- Page 21 and 22: 0-2-3. ROM Check Sum The revision n
- Page 23 and 24: 2-1. Disc Type Disc Type Disc Type
- Page 25 and 26: 2-7. Disc Check Memory Disc Check M
- Page 27 and 28: 6. VERSION INFORMATION On the Test
- Page 29 and 30: 7-2. BLOCK DIAGRAM - AUDIO (DSP) Se
- Page 31 and 32: 7-4. BLOCK DIAGRAM - VIDEO Section
- Page 33 and 34: 7-6. NOTE FOR PRINTED WIRING BOARDS
- Page 35 and 36: 7-8. SCHEMATIC DIAGRAM - RF Section
- Page 37 and 38: 7-10. SCHEMATIC DIAGRAM - MECHANISM
- Page 39 and 40: 7-12. PRINTED WIRING BOARD - DVD Bo
- Page 41 and 42: HCD-S550/S880 41 41 7-14. SCHEMATIC
- Page 43 and 44: 7-16. SCHEMATIC DIAGRAM - DVD Board
- Page 45 and 46: 7-18. SCHEMATIC DIAGRAM - DVD Board
- Page 47 and 48: 7-20. SCHEMATIC DIAGRAM - DVD Board
- Page 49 and 50: 7-22. SCHEMATIC DIAGRAM - DVD Board
- Page 51 and 52: 7-24. PRINTED WIRING BOARDS - AMP S
- Page 53 and 54: 7-26. SCHEMATIC DIAGRAM - AMP Secti
- Page 55 and 56: 7-28. PRINTED WIRING BOARDS - I/O S
- Page 57 and 58: 7-30. SCHEMATIC DIAGRAM - I/O Secti
- Page 59 and 60: 7-32. SCHEMATIC DIAGRAM - DC-DC CON
- Page 61 and 62: 7-34. SCHEMATIC DIAGRAM - CONTROL S
- Page 63 and 64: 7-36. SCHEMATIC DIAGRAM - FL Board
- Page 65 and 66: 7-38. PRINTED WIRING BOARDS - POWER
HCD-S550/S880<br />
3-14. PULLEY (RTR) ASSY<br />
3-15. BELT (CK)<br />
16<br />
shaft<br />
(pulley (RTR) assy)<br />
2 gear (L4)<br />
3 torsion spring<br />
(L)<br />
front<br />
– bottom view –<br />
fig. 1<br />
3 belt (CK)<br />
5 pulley (LCG)<br />
hole<br />
A<br />
1 two bushings<br />
(CDM72)<br />
1 Rotate the pulley (RTR) assy in the direction of arrow A<br />
to disengage the shaft of the pulley (RTR) assy from<br />
the hole of the chassis (refer to fig. 1), and remove it.<br />
2 gear (L5)<br />
4 pulley (L5)<br />
pulley (RTR) assy<br />
B<br />
boss<br />
claw<br />
connector<br />
Tilting the pulley (RTR) assy in the direction<br />
of arrow B, move it over the claw and<br />
the connector of the chassis.