Section 19 Custom Chrome Europe Catalog 2024

19 

TOOLS & EQUIPMENT 

www.custom-chrome-europe.com

Diag4Bike Serial Diagnostic System USB 

Interface 

653745 Field of Application: USB Serial Interface for 653747, 

890084, Unit: Each, Qty.: 1.0 

Diag4Bike Serial Diagnostic System USB & 

Bluetooth Interface 

653746 Field of Application: USB and Blue Totth Serial Interface 

for 653747, 890084, Unit: Each, Qty.: 1.0 

Diag4Bike Diagnostic Software for Harley- 

Davidson 

Includes functions to perform diagnostics of electronic fuel 

injection modules and others (i.e. security modules, ABS etc.) 

through the diagnostic connector on the motorcycle. Hardware 

requirements: Windows 7, 10, 11; HDD with free space min. 10 

GB; RAM 512 MB (1GB and larger recommended); Free USB port, 

Bluetooth (depending on the communication interface used). By 

purchasing this diagnostic software for PC receives a license for 

the diagnostic software for Harley-Davidson® & Buell® profiversion 

v23.x and all the updates for models manufactured up 

to 2023. Also included is 1 x Serial Adaptor cable 4 pin, 1 x 6 pin 

(Can Models), 1 x OBD2 and 1 x Tuning Multi Dongle. 

Overview of control units that can be diagnosed and 

functions: 

• Ignition Module 

• EFI (Electronic Fuel Injection Module), All models 

• TSSM (Turn Signal Security Module), Key FOB with button 

• HFSM (Hands Free Security Module), Key FOB without button 

• BCM (Board Control Module), Key FOB without button 

• Gauges (Speedo, Tacho and Instrument Module), All models 

• SCM (Security Control Module) 

• ABS Module (Delphi + CAN models), All models 

• Radio 

• Thunder MAX EFI, models with 4-pin Datalink connector 

• Read and Clear Diagnostic Trouble Codes, All models, updated 

trouble codes 

• Limits of measured parameters 

• Read Identification data (parts number, VIN number), All 

models 

• Monitoring real-time data: throttle position, temperature, 

oxygen sensors, turn signals etc. 

• Test actuators: injectors, coils, main relay, fuel pump, idle, turn 

signals, tachometer, lamps etc. 

• Buell diagnostics is incorporated in Harley-Davidson® 

diagnostics 

• Unit of measure selection (EU: metric/american, US: metric/ 

standard) 

• Communication interface is CAN ready, models with 6-pin 

Datalink connector 

Toolbox 

• Module replacement (TSSM, HFSM, BCM) 

• ABS Service (Bleeding and configuration, Delphi + CAN 

models), All models up to 2018 

• ACR (Automatic compression release during starting) 

• Cruise Control, Exhaust actuator, EITMS, enable/disable 

• Side Stand Switch configuration, All models 

• Intake solenoid valve configuration on CAN models, only CAN 

models (6-pin Datalink connector) 

• Chassis Fan Cooler configuration (enable/disable) 

• Rider Assistance – ABS, Traction Control configuration 

• Radio Customization – Speakers, ALL models 

• J&M Audio configuration – Custom Audio Flash – J&M 

Corporation (Audio Flash Stage 5) 

• ABS Telltale configuration on CAN models 

• Radio pairing 

• Buell TPS adjustment 

• Speedo pairing, CAN models 

• Reset AFV, all models and Buell® 

• Oil Cooler Fan (enable/disable) 

• Idle speed adjustment, all models with Delphi EFI Module up 

to 2017, for 18-23 models idle speed adjustment available in 

advanced or professional tuning 

• TSSM Customization: PIN read/change, Auto arming, Key FOB 

assignment instruction 

• HFSM Customization: Key FOB, PIN, Auto arming,Sidecar, 

Service mode 

• BCM Customization: Key FOB, PIN, Auto arming, Sidecar, 

Service mode, Keyless ignition, EBAS, Power Lock Switch for 

Saddle bags and Trunk 

• Lights configuration (disable/enable) 

• Front and rear turn signal (LED/Incandescent) 

• TPMS configuration: units BCM, Speedo, Radio 

• TPMS: assignment of valves 

• Fork Lock Switch configuration 

• Disarming (HFSM/BCM module), PIN (read) / FOB assignment 

on armed bike (for BCM modules a CAN disarming cable is 

needed) 

• Odometer units settings, All models (KM / MIL) 

• Button with a direct link to the On Line Help (www.doc4bike. 

eu) 

• Displaying battery voltage 


Part#: 653747, Fitment: 01-23 Softail, 04-17 Dyna, 02-23 Touring, 96-97, 00-01 FLHRI, 96 FLHTUI, 96 FLTCUI, 97-01 FLHTCUI, 

98-01 FLHRCI, 99-01 FLTRI, 02-17 V-Rod, 09-23 Trike, 07-20 Sportster, 21-23 Sportster RH, 21-23 Pan Americar, Fitment 

Note: Only EFI Models. For Tuning Multi Dongle 921209 , Unit: Each, Qty.: 1.0 

19.2

APPAREL 

Diag4Bike Serial Data Link Connector 

Connection cable for serial the data connection of the Diag4Bike 

diagnostic software to connect to the PC or laptop. As a 

replacement or upgrade for use with newer HD models. 

• Unit: Each, Qty.: 1.0 

PART# FITMENT FIELD OF 

APPLICATION 

917717 04-11 Dyna, 01-10 Softail, 02- 

13 Touring, 07-13 Sportster 

HD 4-Pin Data Link 

Connector 

653748 14-20 Sportster, 12-17 Dyna, 

11-20 Softail, 14-20 Touring 

HD 6-Pin Data Link 

Connector for CAN 

Modelle 

919811 21-23 Softail, 21-23 Touring, 

21-23 Trike 

HD OBD 2 Data Link 

Connector 

Tuning Multi-Dongle for Harley-Davidson and 

Indian 

This Diag4Tune Multi-dongle can be used to perform a 

professional tuning on a Harley-Davidson or Indian engines. 

The required Diag4Tune software is included in the Diag4Bike 

Diagnostics Software CCE#653747! The Diag4Bike Multi-dongle 

is a very fast flash tuning device for EFI Harley-Davidson or Indian 

Motorcycles. You can tune all fuel injected 06-23 Harley-Davidson 

motorcycles with the Delphi ECM or Indian motorcycles (except 

Challenger and FTR) until 2021. The first step of tuning is to save 

the original calibration to the server. This will always give the 

possibility to return the motorcycle to its original calibration. 

After that is necessary just select the desired calibration from the 

DIAG4TUNE database in relation to the motorcycle configuration 

(open exhaust / open intake / cams...) and simply save it to the 

motorcycle. You can also create a 100% perfect tune yourself 

for any type of motorcycle configuration, using the Diag4Tune 

AFR Tuning Monitor CCE#619084 and the Smart Power Bench 

II CCE#888128 or any other Power Bench. A Road test is also 

supported. Diag4Bike software version V21.1 and higher is 

required to use the Diag4Tune software with the Multi-Dongle. 

Note: One tuning license must be purchased per tuned 

motorcycle via the Diag4Tune software. The multi-dongle 

is used unlimited times and is needed as a key to establish 

communication to the motorcycle through the Diag4Tune 

software and via the serial interface CCE# 653745 (USB) or CCE# 

653746 USB/Bluetooth. 

921209 Fitment: 21-23 Pan America, 07-20 Sportster, 06-17 

Dyna, 06-23 Softail, 06-23 Touring, 09-23 Trike, 06-17 

V-Rod, 15-21 Indian Bagger, 14-21 Indian Cruiser, 15-21 

Indian Touring, 15-21 Indian Scout, 21-23 Sportster S 

RH1250S 

Fitment Note neu, Not all Tuning Levels are available 

for every model. Not for Indian Challenger and FTR 

Models. Nightster RH under preparation 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

Complete Can-Disarming Cable Kit 

For disarming HFSM/BCM Modules. PIN read / FOB assignment 

on armed bikes. Kit consisting CAN disarming cables to use for 

models up to MY 20 with 6-Pin connector and for models 21 and 

up with OBD. 

Part#: 888130 , Field of Application: Disarming Cable for 

CAN models. Works with Diag4Bike USB Serial Interface 

System. , Unit: Each , Qty.: 1 

6 Pin OBD Adapter (HD 21-up) for CAN 

Disarming Cable Kit 

This is the addition if you already have the CAN disarming cable 

kit (CCE#888130) for models -20 and use it for models 21-up as 

well. 

920358 Field of Application: 6-PIN - OBD Adapter, Unit: Each, 

Qty.: 1.0 

for more details check www.custom-chrome-europe.com 

Tuning License for Harley-Davidson and Indian 

Models 

Tuning license for one motorcycle. The license can be purchased 

via the order form accessible from the DIAG4TUNE software. 

Software version V21.1 and higher is required for use in 

Diag4Tune software. 

ENTERING THE MULTI DONGLE SERIAL NUMBER IN THE FIELD 

ACTIA-LICENSE IS MANDATORY! 

PART# 

FITMENT 

921210 07-20 Sportster, 06-17 Dyna, 06-23 Softail, 06-23 

Touring, 09-23 Trike, 06-17 V-Rod, 21-23 Sportster RH, 

21-23 Pan America. Fitment Note neu: Level 1-4 not 

available for 06 Softail, with 25 Deg. Injectors and 06 

Touring Models. Only Level 0 and 2, available for 07-19 

XL883L, XL883N, XL883R, 07-10 XL883, 15-20 Street, 

06 Dyna, 07-08 FXDSE, 09-10 FXDFSE, 06-07 VRSCD, 

VRSCR, 06 Softail, 07-13, 07-09 FXSTSSE, 10-12 FLSTSE, 

13 FXSBSE, 07-08 FLHRSE, 13 FLHRSE, 07-13 FLHTCUSE, 

09 FLTRSE, 11-12 FLTRXSE, 10-12 FLHXSE. For 21-22 Pan 

America only Level 0 and 2 available, for 23 models in 

progress. for 21-23 Sportster S only Level 0 available, 

Level 2 in progress. 

921211 15-20 Chieftain, 16-20 Chieftain Dark Horse, 16- 

21 Springfield, 17-18 Chieftain Limited Elite, 18-20 

Chieftain Classic, 18-21 Springfield Dark Horse, 

19-20 Chieftain Limited, 21 Chieftain Dark Horse , 21 

Chieftain Elite, 21 Chieftain Limited , 14-15, 17-18 

Chief Classic, 14-21 Chief Vintage, 16-21 Chief Dark 

Horse, 21 Chief Bobber Dark Horse, 21 Chief Vintage 

Dark Horse, 21 Chief Super Limited, 15-21 Roadmaster, 

17-18 Roadmaster Classic, 19-20 Roadmaster Elite, 21 

Roadmaster Dark Horse, 21 Roadmaster Limited, 15-21 

Scout, 16-20 Scout Sixty, 18-21 Scout Bobber, 21 Scout 

Bobber Twenty 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


619080 

653752 

653750 


914797 


653749 

914797 T-adapter 3x18 PT for H-D ECM on 14-23 Touring, Trike and 16-23 Softail 


19.4 

Diag4Bike Parallel Diagnostic Systems 

Professional diagnostic tool for Harley-Davidson workshops and tuning centers. Parallel diagnostics is designed for measuring input 

and output signals from the electronic fuel injection module (EFI) and other modules. Measurements can also be made on running 

engines. The system consists of a set of adapter cables and a breakout box. The breakout box is inserted between the EFI module and 

the motorcycle’s wiring harness so that the system continues to function as normal. Monitoring points for all connector pins of the 

EFI module are clearly arranged on the breakout box. It is possible to measure signals and waveforms from all systems and actuators. 

Disconnecting the ECU from the breakout box allows quick and reliable check of the integrity of the wiring harness in respect to 

continuity, and leakage currents. 

653749 Breakout Box 62 Pin 

619080 36/48-Pin adapter harness for 11-23 CanBus models 

619081 18/18-Pin adapter harness for BCM on CAN equipped models 

653750 36-Pin adapter harness for Delphi EFI models 

653751 73-Pin adapter harness for Touring EFI models 08-11 (not shown) 

653752 35-Pin adapter harness for Magneti Marelli EFI 

619272 T-Adaptor for connection to Harley-Davidson TSM, TSSM, HFSM - DELPHI when using the breakout box

APPAREL 

SEATS & 

TOURING 

888126 


FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

TUNING COMPONENTS: REQUIRE DIAG4BIKE SOFTWARE 

AND INTERFACE 

AFR Tuning Monitor 

The AFR Tuning Monitor is optional but required in order to use 

the advanced Tuning level and consists of two Wideband Air/Fuel 

Ratio Sensors and a compact electronic unit. 

619084 AFR tuning monitor 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

888127 

890085 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

Lambda Installation Set 

This set is an option to the AFR Tuning Monitor. It allows you 

to install a pair of wide band lambda sensors on all exhausts 

without the possibility to simply replace the installed lambda 

sensors (M18 thread). 

Installation on: 

• Exhausts equipped with M18 fitting without enough space for 

longer wide band lambda sensor 

• Exhausts equipped with M12 fitting lambda sensors on newer 

H-D bikes 

• Exhausts without any fitting 

The set contains a powerful double pump, which ensures high 

accuracy and measurement speed of real AFR in each cylinder. 

The pump is powered from 12V supply and can therefore be 

used also for a road test. Necessary tool (but for drill) is included. 

888126 Installation set lambda (Eu) 

890085 Installation set lambda MINI (Eu) 

888127 Kit-Adapter for lambda sensors for open pipes 

Smart Power Bench II (SPB) 

Power bench for bike diagnostics and tuning 

• Simulates engine load for equivalent to road test 

• Simulates double load for comfortable tuning measurements 

(VE maps) 

• Provides measurements for both power and torque curves 

• Facilitates measurement of VE maps for engine tuning 

• Provides the opportunity to carry out engine diagnostics whilst 

under load 

• Utilises built-in fan for engine & rear tire cooling 

888128 Smart power bench 

Note: This is not a stock item, for more detail contact your sales rep. 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



CLASSE 

SRA 

Square U Lock 

Top padlock with U-lock in hardened steel covered in ABS with 

protected U-lock featuring 3 flat-type keys and multiple-disc 

armoured lock. 

PART# 

LOCK WEIGHT/ 

KG 

HEIGHT/ 

MM 

WIDTH/ 

MM 

DIAMETER/ 

MM 

619371 2,76 300 95 20 

Jims EFI Fuel Pressure Gauge Tool 

This gauge is now a must have new tool, since all late model 

Harley-Davidson and including V-Rod motorcycles have Electronic 

Fuel injection. (EFI) If you have a customer that is experiencing 

any of the following engine problems you’ll need this tool: 

• Hesitation under acceleration 

• Loss of power 

• Back firing through the intake 

• Poor fuel economy 

• Stalling out 

• Engine turns over but will not start 

These are just a few symptoms an improper fuel system pressure 

may contribute to. This Fuel pressure gauge is easily installed 

in-line with the motorcycles fuel supply system. All fuel testing 

needs to be performed with the engine running. With this tool 

we supply you with all the necessary hose connections to do this 

test in about the same amount of time it takes to change a set of 

spark plugs. 

653288 EFI pressure gauge 

CLASSE 

SRA 

Blade 85 

Top padlock in hardened steel covered in ABS with protected 

U-lock featuring 3 flat-type keys and multiple-disc armoured 

lock. 

PART# 

LOCK WEIGHT/ 

KG 

HEIGHT/ 

MM 

WIDTH/ 

MM 

DIAMETER/ 

MM 

619375 1,1 88 44 18 

Helmet Lock 

• Don‘t let anyone walk off with your helmet 

• Works on engine guards or frame tubes 

Unit: Each , Qty.: 1 



PART# FIELD OF APPLICATION COLOR DESCRIPTION 

605324 For use with any 7/8“ to 1 1/4“ 

diameter tube. 

605325 For use with any 1 1/4“ to 1 

1/2“ diameter tube. 

774618 For use with any 7/8“ to 1 1/4“ 

diameter tube. 

774619 For use with any 1 1/4“ to 1 

1/2“ diameter tube. 

Chrome 7/8“ - 1 1/4“ 

Tubing 

Chrome 1/4“ - 1 1/2“ 

Tubing 

Black 7/8“ - 1 1/4“ 

Tubing 

Black 1/4“ - 1 1/2“ 

Tubing 

CLASSE 

SRA 

Square Star System 100 

Hardened-alloy steel chain in soft-sheath, 14/15/16 mm 

pentagonal section and SQUARE padlock with 18 mm U-lock 

PART# 

CHAIN LENGTH/ 

CM 

LOCK WEIGHT/ 

KG 

619369 100 2,76 7,80 

TOTAL WEIGHT/ 

KG

APPAREL 

SEATS & 

TOURING 

900528 

FOOT 

CONTROLS 

900529 

Tie-Downs Moto Professional 

888222 Moto Professional tie downs, 

length 1,80 m, with cam-buckle 

and S-hooks, load-strength: 180 

kg/strap; break-strength: 550 kg/ 

strap, pair 

Maximum Security Lockdown 

Anchor 

Mounts on any solid surface and cannot 

be pried up. Made of case hardened 

steel, with a show chrome quality finish. 

This anchor is tamper proof, bolt cutter 

resistant and freeze resistant. Works with 

virtually all range of padlocks, chains, 

cable locks and U-locks. Comes with 3 

sleeved anchor bolts. 

643880 Maximum security lockdown 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

Heavy Duty Tie-Down 

• 2000 lb. strap strength 

PART# LENGTH WIDTH 

900528 1800 25.4 

900529 500 25.4 

Tie-Down Bracket/Cable Guide 

These handy brackets quickly and 

cleanly provide anchor points for 

securing luggage or other items to your 

motorcycle. Mounting hole accepts up to 

a 3/8” (or M10) screw. 

774179 Tie down bracket (sold in pairs) 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

Bungee Cargo Nets 

Made from multi-strand natural rubber 

and wrapped with a knitted polyethelyne 

black cover. Hooks are poly-coated to 

prevent scratching. Sold each. 

TRANNY & 

CLUTCH 

Tie-Downs Loop Moto 

Professional 

888221 Motoprofessional Tie Down 

Loops, blue, load-strength: 260 

kg/strap, break-strength: 800 kg/ 

strap, pair 

Tie-Down Bracket and Cable 

Guide 

This chrome bracket is perfect for use as a 

bungee cord tie-down or as a cable guide. 

Sold on a display card of 10. 

12703 Replaces OEM 38623-68T 

400219 14" x 14" with 6 hooks (repl. 

OEM 98170-88T) 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

Tie-Downs Moto Professional 

888223 Moto Professional ratchet tie 

downs, length 3 m, with coated 

grip and S-hooks, load-strength: 

260 kg/strap; break-strength: 800 

kg/strap, pair 

Bungee Nuts 

Can work as a tie-down knob or an 

excellent spring anchor, and can be used 

to replace shock absorber nuts. Sold in 

pairs. 

20207 5/16"-18 

20208 3/8"-24 

20209 3/8"-16 


Bungee Cords 

Plain black bungee cords to handle your 

tie-down needs. Packs of 10. 

15133 24"-long with two hooks 

15134 18"-long with two hooks 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


688519 

688520 

Pingel Permanent Wheel Chocks 

The Pingel permanent mount Wheel Chock can be bolted 

directly to the floor of any trailer. The Pingel Wheel Chock 

features chrome-plated heavy-duty thick wall steel construction, 

mounting bolts, nuts and washers. Made in the U.S.A. by Pingel. 

688519 Pingel 3 1/2” wheel chock fits front tires up to 3 1/2” 

wide 

688520 Pingel 6 1/2” wheel chock fits front tires up to 6 1/2” 

wide 

Workshop Sliding Seat 

The ideal helper for your shop, garage, storage room or DIY 

workplace. 

Work in a seated position and do not have to stand up for each 

tool individually. This workshop seat from motoprofessional 

offers this. 

It is more stable than many other seats, extremely mobile and 

equipped with a large tool tray. 

• stable steel construction, loadable up to 150 kg 

• comfortable seat made of oil-resistant vinyl 

• large tool tray 

• heavy-duty rollers, 360 degrees rotatable 

Part#: 919382 , Color: Red , Unit: Each , Qty.: 1 

Air Force Blaster 

The Blaster is a compact powerful motorcycle dryer that 

produces 29,000 FPM of warm, dry filtered air, and will dry your 

bike off in minutes. Great for getting into the hard-to-reach 

places. No water spots, no streaks, no more towel drying. All 

steel construction, and made in the USA. 

681873 Air Force Blaster, 220V 

Folding Motorcycle Ramp 

440 mm wide loading ramp has a unique hinge guaranteed to 

support 600 kg. Innovative design and aluminum construction 

make it extremely strong and durable. Extends to an overall 

length of 2390 mm and collapses to 1230 mm, weighing only 


14,3 kg. 

20205 Folding ramp 


Air Force Blaster ‘Side Kick‘ 

The Air Force Blaster has been so successful, that the 

manufacturer has now come out with a smaller, more compact 

version called the Side Kick. It produces 18,000 FPM of air, and 

will dry your bike off in minutes. Like its big brother, it features 

all steel construction, weighs only 3 lbs., and is made in the USA. 

681874 AFB Side Kick, 220V

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

MC625R Heavy Duty Air Lift 

• 1,750 lb. Max Capacity 

• Drop panels at front and rear of lift 

• Max raised height of 40 inches 

• Lowered height is 8.5 inches 

• Automatic safety lock 

• Loading ramp included 

888457 

914680 

PART# COLOR LENGTH WIDTH 

612228 Blue 2200 750 

888457 Red 2200 750 

914680 Black/Orange 2200 750 

Side Panels, Extensions and Ramps for MC625 

Heavy Duty Air Lift 

Full line of side panels, extensions, ramps and tool holders to 

attach to our leading line of Hydraulic and Air Lifts. 

Front and Rear Extension: Extend the deck 610 mm! These 

extensions can be used on either end or use 2 for 1.220 mm extra 

space in total. 

Side Panel Set, Loading Ramp: Standard side panels are 340 mm 

/ each, which is 680 mm extra space of deck surface. The extra 

wide side panels are 500mm / each, which means that you get 

1.000 mm extra space of deck surface. 

PART# TYPE COLOR DESCRIPTION UNIT 

612229 Standard Front and Gray 

Qty.: 1 Rear Extension 

900513 Standard Front and Black 

Rear Extension 

900514 Wide Front and Black 

Rear Extension 

900515 Standard Sidepanel Black 

Extensions 

900516 Wide Sidepanel Black 

Extensions 

900517 Trike Standard Gray 

Sidepanel 

Extensions 

900518 Trike Wide Gray 

Sidepanels 

Extensions 

Width x Length 

(mm): 750 x 610 


(mm): 750 x 610 


(mm): 1740 x 610 


(mm): 340 x 2195 




(mm): 335 x 597 


(mm): 495 x 597 

900519 Side Panel Ramps Gray Width x Length 

(mm): 265 x 775 

900520 Long Side Panel 

Ramps 

Gray 



900527 Extended Ramp Gray Width x Length 

(mm): 380 x 1160 

Each 

Each 

Each 

Pair 

Pair 

Pair 

Pair 

Pair 

Pair 

Each 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

MC625R TOOL HOLDER 

PART# COLOR 

900521 Gray 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

MC10R Universal Wheel Clamp 

The MC10R Universal Wheel Clamp allows one person to 

load and unload a motorcycle on any flat deck lift. The pivot 

mechanism uses the weight of the bike to hold itself upright, 

leaving your hands free to secure the bike. The included rails 

mount to the deck so you can also slide the MC10R forward to 

handle short wheelbase bikes. 

685827 MC10R Universal Wheel Clamp 


LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


MC625R Air Lift Wheel Set 

PART# 

FITMENT 

900523 MC625R 

MC455 Fat Jack Rebuild Kit 

PART# 

FITMENT 

900524 MC455 

K&L Supply MC464 Fat Jack Dolly 

Designed to work with the Fat Jack Dolly casters allow 

movement of stand with stability 1,000 lb capacity. 

631453 Fat Jack Dolly 



K&L Supply MC15 Cycle Dock 

Permits one person to load and unload a motorcycle in a trailer, 

pickup truck or service lift. Pivot mechanism uses the weight of 

the bike to hold itself upright, leaving your hands free to secure 

the bike. Simple in design and ruggedly built to last for a long 

time. Use supplied mounting rails to mount Dock into trailer or 

pickup. Rails mount to deck so you can slide the Dock out leaving 

just the mounting rails behind, freeing up your truck or trailer 

for other uses. Kit comes complete with wide rockers, Cradle 

stop (upright), mounting plate, support arm (with eyelets and 

adjustable feet) and two mounting rails. 

641641 Complete kit 

Note: The use of tie-downs is strongly recommended. 

MOBILE BENCH 

• Combination workbench, tear-down table and tool storage 

facility 

• Comes with heavy duty 4” casters (2 rigid & 2 locking swivel) 

• Table top features a drain hole 

PART# 

COLOR 

900525 Blue

APPAREL 

30112 

SEATS & 

TOURING 

30110 

FOOT 

CONTROLS 

HAND 

CONTROLS 

K&L Supply Adjustable Shop Dolly 

Convenient mobility when working on your bike. Designed to 

work specifically with the CC #21004 Motorcycle Lift. Once your 

bike has been lifted clear of the ground, just roll the dolly into 

place under the bike and lower the lift until you can remove it. 

Features 15" maximum height, swivel neoprene wheels with 

adjustable base (13" to 20") and 1000 lb. capacity. 

21000 Sold each 

LIGHTING 

ELECTRICAL 

K&L Multi-Lift Motorcycle Lift 

Features locking neoprene casters, powder-coated finish, 16" 

of padded contact area, 4-ton bottle jack, tie-down anchors, 

heavy-duty 1200 lb. capacity, foot operated valve and locks. Fully 

adjustable from 4 1/2" to a maximum height of 17". 


K&L Adapters and Ramp Tool for Multi-Lift 

For use with CC #21004. Features thick rubber pads to protect 

frame and zinc-plating to last long. Work on K&L multi lift only. 

Low riding ramp tool features diamond plate surface and rubber 

feet. Sold each. 

30112 Low riding ramp tool for use with multi-lifts when trying 

to lift a lowered bike 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

K&L Supply MC450 Center Jack Stand 

Easy, scissor-type action lifts most motorcycles up to 1000 lbs. For 

use on ground or lift tables. 

30115 Scissor lift 

631452 Optional non-slip rubber pad 

FRAMES 

FORKS & 

SHOCKS 

K&L Supply MC455 Fat Jack 

All of the features that make the MC450 Center Jack great and 

more. Fat Jack’s wider deck surface with rubber non-skid pad 

increases your lifting area. The deck measures 16"-long x 10"- 

wide. Lifting dimensions are 3 1/2"-minimum x 13"-maximum 

with a 1,000 lb. capacity. 


SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



607699 

• Rear wheel cutout which slides into the 

platform bottom (60 x 34 cm) 

• 8 maintenance-free ball bearings 

• Greasable pivot bolts 

• Removable front safety plate 

• Electro-hydraulic drive installed under 

the platform with sheet steel cover 

• Ramp with ground sliding rail, 

automatic move-in when the platform 

is lifted 

• 2 socket plugs in the cover of the 

hydraulic unit 

• Preparation for mounting a chassis 

607679 EH 400 (400 Kg), red 



ECON Motorcycle Lift EH 400 

ECON platform lifts: the comfortable, safe 

and fast way upwards. The EH 400 ECON 

platform is intended for all Sport, Touring 

and Enduro bikes as well as scooters wit a 

weight up to 400 kg. 

Features: 

• Load capacity 400 kg 

• Large 220 x 70 cm platform 

• Maximum height 120 cm, min. height 

16 cm 

• Drive: electro hydraulic pump 

• Drive power: 1.1 kW - 230 V 

• Control panel with push buttons and 

magnetic back side 

• Safety: Normally closed safety valve, no 

mechanical lock required 

• Certification: CE 

Standards: 

607680 EH 400 (400 Kg), blue 



and fast way upwards. THE EH 530 ECON 

platform is intended for all Sport, Touring, 

Enduro bikes and Scooters with a weight 

up to 530 kg. 

Features: 




16 cm 








Standards: 










is lifted 




607681 EH 530 (530 Kg), red 

607682 EH 530 (530 Kg), blue 



and fast way upwards. THE EH 530 ECON 

platform is intended for all Sport, Touring, 

Enduro bikes and Scooters with a weight 

up to 600 kg. 

Features: 




16 cm 








Standards: 










is lifted 




607683 EH 600 (600 Kg), red 

607684 EH 600 (600 Kg), blue 

607699 Side extensions for EH 600 only

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

ECON Side Extensions and C-Rails 

With C-rails you can slide the small side extension with tools on 

the place you need. 

607689 Side extension, short with C rail 

607690 C-rail pair 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

ECON Motorcycle Lift EH 600 Trike 

The EH 600 Quad by ECON has become a predominant tool in 

the workshop. Load capacity, lifting height, length and, last but 

not least, the width of the platform significantly exceed standard 

measures. The EH 600 Max extremely sturdy basic design has 

made it possible to install wide side extensions (2 x 30 cm). 

Features: 


• Large 230 x 80 cm platform; 230 x 140 cm with extension 

• Maximum height 120 cm, min. height 16 cm 



• Control panel with push buttons and magnetic back side 

• Safety: Normally closed safety valve, no mechanical lock 

required 


Standards: 

• Rear wheel cutout which slides into the platform bottom (60 

x 34 cm) 




• Electro-hydraulic drive installed under the platform with sheet 

steel cover 

• Ramp with ground sliding rail, automatic move-in when the 

platform is lifted 

• 2 socket plugs in the cover of the hydraulic unit 


607685 EH 600 Trike (600 Kg), red 

607686 EH 600 Trike (600 Kg), blue 

ECON Front Extensions EH 600 

Usefull helper for long Choppers. 

607691 Front extension for EH 600 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

ECON Aluminum Plates 

607692 Aluminum chequered plate for EH 400/530 

607693 Aluminum chequered plate for EH 600 

TOOLS & 

EQUIPMENT 



YCX1.5 Smart Battery Charger 

• Fully automated 7-step charge and maintenance process refined by GS Yuasa engineers for unrivaled battery care 

• Charges batteries faster than comparable models thanks to higher performance 

• Engineered with GS Yuasa‘s world-leading battery manufacturing expertise to extend life, maintain performance and ensure 

ultimate reliability 

• Optimum charging performance for conventional lead-acid, AGM, lithium and gel batteries 

• Charge and charge retention for motorcycle and powersport batteries (6 V and 12 V). charging from 2Ah to 30Ah; Trickle charge 

up to 120 Ah 

• Automatic battery diagnosis with patented rejuvenation phase to stop the sulphation process 

• Detection and reporting of all charging errors caused by battery problems 

• Automatic trickle charge with energy-saving eco mode maintains the optimal state of charge during storage of the battery 

• Rugged, integral clamp and spade terminals attach permanently for plug-and-play connection 

• Compact format with interchangeable sockets for use in Europe, UK and USA 

• Enhanced safety features with short circuit, overcharge and reverse polarity protection provide ultimate reliability 

• Easy to use thanks to simple navigation buttons and meaningful indicator LEDs 

Part#: 924932, Field of Application: For all AGM, Sealed Maintenance Free, GEL, Lithium and Lead Acid Batteries, Color: 

Black, Unit: Each, Qty.: 1 

YCX6 Smart Battery Charger 

• The fully automatic nine-stage charging and charge retention process, refined by GS Yuasa engineers, ensures maximum battery 

protection 

• Engineered with GS Yuasa‘s world-leading battery manufacturing expertise to extend life, maintain performance and ensure 

ultimate reliability 

• Charger designed for commercial use, popular and tried and tested by workshops and technicians 

• Active cooling ensures stable power delivery and extends the life of the charger 

• Self-activating float mode maintains optimal state of charge during battery storage 

• Faster charging thanks to higher output power than comparable models 

• Optimum charging performance for conventional lead-acid, start-stop, EFB, AGM, lithium and gel batteries 

• Charging and charge retention of 12V batteries (even from the fully discharged state). Charging up to 120 Ah and trickle charging 

up to 180 Ah 

• Automatic battery diagnosis with patented rejuvenation phase to stop the sulphation process 

• Detection and reporting of all charging errors caused by battery problems 

• One charger for multiple uses: thanks to the adjustable output power, an unrivaled range of battery capacities is covered 

• Automatic trickle charge with energy-saving eco mode maintains the optimal state of charge during storage of the battery 

• Enhanced safety features with short circuit, overcharge and reverse polarity protection provide ultimate reliability 

• Durable, splash-proof (IP44) construction with robust, integrated clamp and spade terminals 

• Easy to use thanks to simple navigation buttons and meaningful indicator LEDs 

Part#: 924933, Field of Application: For all AGM, Sealed Maintenance Free, GEL, Lithium and Lead Acid Batteries, Color: 

Black, Unit: Each, Qty.: 1 



APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Junior 800, Selectable Lead 

Acid/Lithium 

• Output: 12 V @ 800 mA 

• Input voltage: 220 to 240 Vac, 50/60 Hz 

• Charger weight: 467 grams 

• Size: 8,3 cm x 5 cm x 3,5 cm 

• ISMTM Microcontroller constantly 

updates charge sequence for smooth 

transitions between charging steps 

• Spark proof 

• Short circuit protected 

• Reverse hook-up protection 

• Safety timer 

• Selectable for AGM, flooded and GEL or 

Lithium (LiFeP04) batteries 

895139 800 mamp Power Battery Tender 

Battery Tender Accessory Bag 

This bag will accommodate the Battery 

Tender Junior or the Battery Tender Plus 

including all connectors and accessories. 

2851017 Accessory bag 

5A Power Tender Series High 

Efficiency by Battery Tender 

The Battery Power Tender Plus High 

Efficiency is a 5 amp battery charger that 

will fully charge and maintain a battery 

at its proper storage voltage without 

the damaging effects caused by trickle 

chargers. 

• Short Circuit Protected 

• Reverse Polarity Protected 

• Safety timer: 72 hours Dimensions: 

3.99 W x 8.26 L x 2.34 H 

890449 Battery Charger, Power Battery 

Tender® Plus HI 12 V 5 A 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

Lithium Battery Charger 

WP800 by Battery Tender 

• Input: 120 VAC @ 60 Hz 

• Designed to charge any 12 volt Lithium 

(LiFePO4) Battery 

• Spark Proof 

• Short Circuit Protected 

• Reverse Polarity Protected 

• Auto recovery mode for batteries with 

very low voltage 

• Weatherproof 

• Weighs only 1 Pound 

890547 Lithium battery charger WP800 

Battery Tender Waterproof 

Charger 0,8 Amp 

• Spark-proof, even when the leads are 

touched together 

• Reverse polarity protected 

• Will not damage charger if hooked up 

incorrectly 

• Easy to install and use 

• Safe in all weather conditions 

• Will safely charge and maintain any size 

12-volt battery though 200 amp-hour 

capacity 

• Safe and easy to use on all lead acid 

batteries 

• Solid-state two color LED indicates start 

of charge 

• Output: 12V @ 800mA - Input voltage: 

220 to 240Vac, 50/60Hz 

Battery Tender Waterproof Chargers 

686744 For Europe 

Replacement Parts 

2851015 Alligator clip-style quick connect 

harness (sold each) 

2851016 Black fused grommet-style quick 

connect harness (sold each) 

Battery Tender 12-Volt 4-Bank 

International Chargers 

The 4-Bank International battery tender 

charging station works anywhere in the 

world! Designed to fully charge a battery 

and maintain it at proper storage voltage 

without the damaging effects caused by 

trickle chargers. 

• Features 4 independent charging 

systems and 12 volts at 1.25 amps per 

station 

• Weighs less than 3 lbs.! 

• Operates anywhere in the world (100- 

240 VAC 50/60 Hz.) 

• Microprocessor controlled constant 

current charging 

• Reverse polarity protected 

• Complies to all International safety 

standards 

• Perfect for all AGM, sealed maintenance 

free and flooded batteries 

• Optional 25 ft. extension leads available 

• Features 2 year warranty! 

Battery Tender 4-Bank Chargers 

686834 For Europe 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



895143 

895140 

Battery Tender is a revolutionary 

charger that charges any 12 or 6-volt 

lead-acid or gel battery and keeps 

it at full charge forever, WITHOUT 

DAMAGING OR DESTROYING THE 

BATTERY! It is NOT a trickle charger. 

Just hook it to a battery and forget it. 

Comes with alligator clips and quick 

disconnect connections. 

895141 

Gauge LCD Battery Meter 

• QDC Plug 

895143 Gauge LCD Battery 

LED. Battery Gauge 

Simple two-wire connection & a compact 

size (about 2” x 3/4” x 3/16”) make 

installation a breeze. Universal fitment 

designed for all 12 V charging systems. 

Fits: Universal Fitment for 12V Battery 

Charging Systems 

774219 Chrome (ea) 

774218 Black (ea) 

USB Port Charger 

• QDC Plug 

895144 USB Port Charger 

1,25Amp and 4Amp Dual 

Selectable Power Tender 

• Output: 12V or 6V switchable 

• Input voltage: 220 to 240Vac, 50/60Hz 

• Charger weight: 612,3 grams 

• Size: 17,2cm x 9,3cm x 4,9 cm 

• ISMTM Microcontroller constantly 

updates charge sequence for smooth 

transitions between charging steps 

• Spark proof 

• Short circuit protected 

• Reverse hook-up protection 

• Safety timer 

• Designed for AGM, Standard, Flooded 

and GEL batteries 

• Lithium (LiFeP04) - Switchable 

895140 1,25Amp Power Battery Tender 

895141 4Amp Power Battery Tender 



APPAREL 

SEATS & 

TOURING 

CH-26000 Battery Charger 

• Switchable for Lead-acid / AGM / Gel / 

Lithium batteies 

• Output: 6V, 12V or 24V switchable 

• Operating voltage: 200V-250V/AC50HZ 

• Charging current: 6V - Auto/8A/24A ; 

12V - 4A/12A/26A ; 24V - 2A/6A/13A 

• LCD Display 

• USB ports DC 5V 

• Winter mode 

• Repair function 

• Automatic lithium BMS unlock 

• Provide protection against: over 

temperatur, short circuit, overload, 

high voltage, low voltage, reverse 

connection, lithium battery BMS unlock 

Part#: 921666, Description: 26A, Unit: 

Each, Qty.: 1 




• Output: 6V, 12V or 24V switchable 


• Charging current: 6V - 4A/8A/15A ; 12V - 

4A/8A/15A ; 24V - 2A/4A/8A 

• LCD Display 







Part#: 921665, Description: 

15A, Unit: Each, Qty.: 1 






• Charging current: 1A-6V / 1A-12V 






Part#: 921663, Description: 1A, Unit: 

Each, Qty.: 1 






• Charging current: 3.5A-6V / 3.5A-12V 







Part#: 921664, Description: 3,5A, Unit: 

Each, Qty.: 1 

Optimate 3 Battery Charger 

OptiMate 3 is the most trusted fully sealed 

battery saving charger and maintainer 

– The most popular motorcycle charger 

world-wide! Fully automatic multi-step 

program brings the battery safely to 

full charge. The all-in-one tool for 12V 

battery care at home. Diagnoses, recovers, 

charges, tests and optimally maintains, 

automatically. No risk of overcharging. 

Totally safe for vehicle electronics. Sparks 

suppressed. Safe for long-term battery 

maintenance. Automatic shut-down if 

short-circuited or battery disconnected. 

7 Step fully automatic operation (low volt 

(from2V) start, desulfate safe, pulse safe, 

controlled charge, optimize, test after 

charge, Optimate maintenance). 

• For AGM, GEL, STD 12V batteries from 

2.5 – 38Ah 

• 0.8A (constant current) charging amps 

• Nominal: 12V range: 2V - 14.4V 

charging volts 

• Fully automatic operation 

• Indoor / Outdoor use (lowest 

temperature: -40°F / -40°C). 

• Weatherproof case with wall mount 

• Low Volt Start of 2V + 2 step 

desulphation recovery 

• Including weatherproof battery lead 

(SAE) and battery clip set 

Part#: 653138 , Field of Application: 

For all AGM, Sealed Maintenance 

Free, GEL, and Lead Acid Batteries , 



OptiMate Lithium 4s 0.8A 

8-step 12.8V 0.8A sealed battery saving 

charger and maintainer. Ultimate 

protection for your high performance 

Lithium battery. Fully automatic multistep 

program brings the battery safely 

to full charge – Connect to the battery 

and OptiMate Lithium 4s 0.8A does the 

rest, no supervision required! For Li-Ion 

12.8V / 13.2V power sport battery types 

made with LiFePO4 / LFP technology. 

Maintains and protects LiFePO4 batteries. 

No risk of overcharging. Totally safe for 

vehicle electronics. Sparks suppressed. 

Safe for long-term battery maintenance. 

Automatic shut-down if short-circuited or 

battery disconnected. 

8 Step fully automatic operation (low volt 

(0.5V) start, low volt safe, safe - monitor 

cells, test - cell damage, cell-balancing 

charge, optimize, test after charge, 

Optimate 365 maintenance). 

• For Lithium (LiFePO4) 12.8/13.2V 

batteries from 1 – 10Ah 

• 0.8A (constant current) charging 

• Nominal: 12.8V range: 0.5V - 14.4V 

charging volts 

• Fully automatic operation 

• Indoor / Outdoor use (lowest 

temperature: -40°F / -40°C) 

• Weatherproof case with wall mounts 

• Low Volt Start of 0.5V + 3 step low volt 

save and test 

• Including weatherproof battery lead 

(SAE) and battery clip set 

Part#: 607677 , Field of Application: 

For all Lithium, AGM, Sealed 

Maintenance Free, GEL, and Lead Acid 

Batteries , Unit: Each , Qty.: 1 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


CycleSkyns by Cycle Visions 

Protect your paint from accidents while 

working or storing your bike. These 

high quality neoprene covers are formfitted 

to your tank or fender size. The 

Saddle bag cover is only for fiberglass 

bags. Made from 4mil Neoprene wet 

suit material with or without pockets on 

the tanks. Perfect for storing bolts from 

h-bars while assembling. 

683951 5.2 Fatboy Tank Cover 

11-Slot T-Handle Rack 

• Chrome finish, one piece design 

• Easily hangs on the side of most tool 

boxes 

5008114 11-Slot T-handle Rack 

Chrome Cable Ties 

These cable ties feature speciallyprocessed 

chrome-plating to resist 

cracking, and are ideal to dress up any 

wiring job. Sold in packs of 5. 

85095 300 mm (11 3/4"-long) 

Dual Drive Mini T-handles 

• Use T-handle drive side to tighten/ 

loosen fasteners and shaft side for quick 

installation/removal of fasteners 

• For tight access and easy transport 

• Use with 1/4" & 3/8" drive sockets, Allen 

drive bits, crow's feet, swivels, etc. 

• Lifetime replacement warranty 

5008359 1/4" drive (6 1/2" long) 

5008360 3/8" drive (7 3/4" long) 

Motion Pro T–Handle Drivers 

Easy-to-use T–handle tools allow optional 

ways to use any 1/4" or 3/8" drive 

attachments such as sockets, hex drives, 

crow’s foot or swivels. Motion Pro lifetime 

replacement warranty. 

5008158 1/4" drive (8 1/2" long) 

5008159 3/8" drive (10 1/2" long) 

Flat Rocker Box Wrench by 

Motion Pro 

Specially designed for use on Evolution 

and Twin Cam 88 engines. Made flat for 

hard-to-reach places. Eases removal of 

rear rocker box when engine is still in the 

frame. Built with a 3/16" hex head and 

an adapter hole for a torque wrench. 

04700 Rocker box wrench for 86-20 

Sportster, 85-94 FX Model, 

91-98 Dyna, 84-99 Softail, 85-98 

Touring, 95-02 Buell 

JIMS Chaser Tap Set 

This thread chaser set is an inexpensive 

way to clean up threads on frames or 

other parts that have been powder 

coated or painted. Thread sizes are 

coarse, 1⁄4”-20, 5⁄16”-18, 3⁄8”-16, 7⁄16”-14, 

1⁄2”-13, and 9⁄16”-12. Chasers are zinc 

plated and made from 1027 steel. 

622046 Sold as a set 

19 5008435 Wall Bracket for T-handle rack 


Wall Bracket for T-handle rack 

• Allows easy mounting of the T-handle 

rack to a toolbox, wall, post or any 

other flat surface 

• Features a quick release pin for 

removing and attaching the T-handle 

rack 

• Includes built in bottle opener 

Sliding T-Driver with Sockets 

This 12″ long sliding T-handle 3/8″ driver 

comes with 8, 10, 12, 14, and 17mm 

sockets, 5 and 6mm hex bits, and a #2 

phillips screwdriver bit on a storage 

rail that attaches to the handle for safe 

keeping. 

Part#: 922924 , Unit: Set , Qty.: 1 

Folding Sockethead Wrenches 

American-made stainless steel folding 

tools available both with inch sizes and 

metric. 

84191 Folding sockethead-tool, inch, 

1/16", 5/64", 3/32", 1/8", 5/32", 

3/16", 7/32", 1/4"

APPAREL 

SEATS & 

TOURING 

Outback’r 13-in-1 Multi-Tool by CruzTOOLS 

Inspired by outdoorsman-style multi-tools, yet designed 

specifically for Harley-Davidson motorcycles, the Outback'r H13 is 

a powerhouse of functionality. 

• At only 9 ounces and 3.5 inches, you won't have any trouble 

finding a spot to carry it 

• Built to last using heat-treated chrome vanadium and carbon 

steel 

• Includes three hex keys (5/32", 3/16", and 1/4"); two Torx keys 

(T25 and T27); slotted and Phillips screwdrivers; a socket driver 

with 3/8", 7/16", and 1/2" sockets; 10mm box and 9/16" openend 

wrenches plus a spoke wrench 

645530 Outback’r 13-in-1 Multi-Tool 

8-Piece Sockethead Wrench Set 

Chrome vanadium quality 8-piece sockethead wrenches. Sizes 

from 1/16" to 1/4". 

84185 8-piece set 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

Teardrop Tool Boxes 

Our popular chrome reproductions of the Original Equipment 

‘teardrop’ tool box used from 40-59 are available in two 

different versions, with your choice of the old-style lock or a 

more modern, conventional tumbler lock for improved security. 

26457 Tool box with conventional tumbler lock 

Colony Tool Box Mounting Kit 

36183 A complete hardware kit for mounting the tool box on 

models from 36-61. 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

Teardrop Toolboxes for Softail Models 

Add a classic touch to your Softail model with a chrome-plated 

replica of the toolbox used from 40-59. The chrome-plated 

mounting brackets are held by the fender support bolts and 

passenger footrest. Left-side kit is ideal for Fat Boy and FLSTN 

models because of the shotgun exhaust. Fit Softail models from 

84-99 (except 90-11 Heritage Softail Classic models). 

09767 Left-side kitC 

RoadTech IN2 Tool Kit for Indian Motorcycles 

The perfect travel tool kit for Chief, Chieftan, Roadmaster and 

Scout model Indian Motorcycles. 

• Set of two 27mm x 14mm x 22mm axle wrenches and a 

14x16mm axle hex adapter 

• Combination wrenches (10mm, 12mm, 13mm) 

• 8” adjustable wrench 

• Mini ratchet with 2” extension and sockets (8mm, 10mm, 

12mm, 13mm) 

• 5 Torx keys, 5 hex keys 

• 6-in-1 screwdriver 

• Locking pliers 

• Shock adjust tool 

• Duct tape, cable ties, mechanics wire 

• Tire pressure gauge 

Part#: 922923 , Unit: Kit , Qty.: 1 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


19.19

20981 

Speedkit HD by CruzTOOLS 

• Includes significantly more content than most OEM replacement kits 

• Higher quality tools and pouch 

• Fits most OEM storage cavities 

• Lower cost than most OEM replacement toolkits 

645490 Speedkit HD toolkit 

20982 



RoadTech Teardrop Tool Kit for Harley-Davidsons by CruzTOOLS 

The RoadTech tool kit series combines road-proven EconoKIT content with a way-cool 

mini ratchet and socket set. Softail riders now can get in on the action with the new 

RoadTech Teardrop which packs everything from the RoadTech H3 into a compact 

pouch designed to fit genuine and aftermarket teardrop tool boxes. Kit includes mini 

ratchet and sockets, combination wrenches, locking pliers, adjustable wrench, 6-in-1 

screwdriver, LED flashlight, tire gauge, hex and Torx keys, and much more… 

645534 CruzTOOLS teardrop tool kit 

RoadTech H3 Tool Kit by CruzTOOLS 

Combines the best features of the popular EconoKIT H1 and MiniSet ratchet tool kit 

into one roll-up pouch. Features include: 

• Mini ratchet and sockets, combination wrenches, locking pliers, adjustable wrench, 

6-in-1 screwdriver, LED flashlight, tire gauge, hex and Torx keys, and much more 

• All tools are professional mechanic-grade with a lifetime guarantee by CruzTOOLS 

645532 RoadTech H3 Tool Kit 

20983 

Econo Kits by CruzTOOLS 

Econo kits cut cost but not content for 

the rider who demands the best on the 

road. Lifetime guarantee on tools from 

manufacturer. 

Roll-Up Tool Kit 

Includes the most common wrench sizes, 

an adjustable wrench, locking pliers, 

two spark plug socket sizes,Torx and 

sockethead wrenches, tire gauge and lots 

more. Measures 91/2"-long with a rolled 

diameter of 3" and weighs three pounds. 

20981 Roll-up tool kit 

Zip-Up Tool Kit 

Features five combination wrenches, 

spark plug multi-tool, 6-in-1 reversible 

screwdriver, essential Torx and sockethead 

wrenches. All in a compact package 

weighing less than two pounds and 

measuring 9"-long, 4"-wide by 1 1/2"- 

deep. 

20982 Zip-up tool kit 

Hex/Torx Combo Tool 

Features the standard sizes required on all 

late model bikes in a convenient pocket 

size carry tool. 

20983 Hex/Torx combo tool

APPAREL 

SEATS & 

TOURING 

Outback`r M14 Folding Metric 

Multi-Tool 

Enough tools to get you out of a jam, 

but not weigh you down! The Outback’R 

multi-tool is a must-have for Indian 

Motorcycles. The Outback’R OM14, 

provides 14 tools in a 3.5” long multitool 

that weighs only 9-ounces. 

• Hex Keys – 3, 4, 5, 6mm 

• 13 & 14mm open wrenches 

• 3 sizes of spoke wrench 

• Slotted & Phillips screwdrivers 

• 8, 10, 12mm sockets & 1/4″ driver 

Part#: 922927 , Unit: Each , Qty.: 1 

Flashlight Magnifier 

• Flashlight and magnifying glass in one 

• Perfect for reading spark plugs, jet 

sizes, and many other uses 

• Durable plastic head with chrome steel 

body 

20155 Flashlight magnifier 

TICKOPUR Tr3 Special Cleaner 

Acid special cleaner - with stronger 

cleaning power. For fuel residues, 

carburetors and injection nozzles, tools, 

machine parts. It removes mineral 

residues. 

607712 5 L 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

645536 

645535 

Terminal Pin/Receptacle 

Extractors 

Use with Molex style connectors on most 

models 80-13. 

400376 Pin extractor 

400377 Receptacle extractor 

EXHAUST 

INTAKE 

CruzTOOLS 3/8” Drive Socket 

Bit Sets 

Quality is comparable to top professional 

tools, with a heat-treated chrome 

vanadium alloy that exceeds ANSI 

specifications. Top-grade hex and Torx 

bit socket sets include all the sizes you’ll 

need. Each set includes a socket rail with 

handle for quick organization and easy 

transport. Sizes are easy to read with 

reverse laser imprint on each socket. 

645535 10-piece HEX Standard Inch 

Socket Set 

645536 10-piece TORX Socket Set 

685973 10-piece HEX Standard Metric 

Socket Set 

Molex MX-150 Terminal 

Removal Tool by Namz Cycle 

Products 

Molex MX-150 style removal tool. 

Removes both pins and receptacles. Made 

in the U.S.A. 


TICKOPUR R33 Standard 

Cleaner 

Universal cleaner for carburetors, 

injection nozzles, injection system parts, 

tools, machine parts. It removes general 

soiling. 

607710 5 L 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

Delphi-Packard Terminal 

Removal Tool by Namz Cycle 

Products 

A great tool for when working on 

Delphi-Packard weather-pack terminal 

connectors. Made in the USA. 

Fuel Hose Pinch off Pliers 

Plastic 

696806 

FRAMES 

FORKS & 

SHOCKS 


SHEETMETAL 

3/8” Drive 17 piece socket kit by 

Gedore 

Another high quality tool kit by Gedore 

available in metric or inch. You can also 

choose between two ratchet styles, one with 

fine gearing which allows for movement 

of the ratchet in small steps in hard to 

reach spots and one with heavy duty coarse 

gearing that takes loads of tightening 

torque. 

684854 Metric kit with fine geared ratchet 

Universal Mini Pick Tool 

Universal Mini Pick Tool, perfect for 

removing JAE, JST & Other Misc. “Mini” 

Terminals. 



Motion Pro Snap Ring Pliers 

• The right tool for the right job 

• Economical pliers that easily do both 

inside and outside opening snap rings 

or clips 

• Includes three extra sets of tips, one 

additional straight tip, and two offset 

or angled tips 


INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


Static Timer 

This static-timing device permits you to 

lock your advance position while you 

static-time it. Helps reduce kickback while 

promoting easier starts and smoother 

running. 

20134 Fits all models with point-type 

ignitions from 70-78 

Aluminum Vice Jaws by Accel 

Magnetic soft jaws allow you to put a 

firm grip on parts with a sensitive surface. 

Strong magnets attach them to almost 

any vice. 

668369 Vice jaws 

Front Lever Grip Clamp Lock 

• For parking at slope or for maintennce 

• Padlock can be hooked for easy lock. 

(padlock isn‘t included) 

• Inner Diameter : 36mm 

PART# 

COLOR 

923964 Black 

923963 Orange 


RevTech Oil Change Helper 

Take the mess out of the oil change 

process. Forget the clean-up of oil 

drippings on the engine case and frame 

tubes. Snaps behind the oil filter mount 

to funnel oil away from the bike into the 

drain pan. 

20989 Fits Evolution models from 92-99 

and Twin Cam 88 models from 

99-02 (sold each) 

Note: Must remove crank position sensor when using on Twin 

Cam 88 models 

Cable Oiler 

Designed to direct lubricant into the cable 

core, not on the shop floor. Fits most 

throttle, clutch and brake cables. 

400591 Cable Oiler 

JIMS Dual Gauge Leakdown 

Tester 

Includes a 12mm and a10mm (for our 

Metric friends) adapter. The hose assembly 

has both 14mm and 18mm spark plug 

threads. The tool is easy to use and will 

troubleshoot cylinder leakdown issues 

such as valve seat issues, bad rings, bad 

head gasket, etc. 

622189 Use on all models. 

Note: Includes Twin Cam and aftermarket motors 


400503 Oil Filter Wrench 


Oil Filter Wrench 

Fits all Harley-Davidson spin-on filters. 

3/8" socket drive. 

Auxiliary Gas Tank 

Auxiliary gas tank to allow engine testing, 

while the original gas tank is off the 

frame. Includes four feet of 1/4" fuel line 

and an ‘in-line valve’ 

84175 Auxiliary gas tank

APPAREL 

Thread Cutting And Repair Sets by Völkel 

Based on the experience of 95 years in the production of thread cutting tools VÖLKEL has developed a worldwide leading supplier 

of standard thread cutting tools. 

SEATS & 

TOURING 

FOOT 

CONTROLS 

685770 

685771 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

Thread Cutting Kits 

685770 UNC 1/4” to 1/2” 

685771 UNF 1/4” to 1/2” 

914378 HSS-G M3-M12 

914379 HSS-G M3-M20 

914380 HSS-G M5-M20 

Hexagon Die Nuts 

652796 M3 to M12 

652797 1/4” to 1/2” UNC 

652798 1/4” to 1/2” UNF 

INTAKE 

ENGINE 

GASKETS 

685772 

685773 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

Thread Repair Kits 

685772 UNC 1/4” to 1/2” 

685773 UNF 1/4” to 1/2” 

914360 M6-M14 

Countersink Set 

685794 6,3 to 20,5mm 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

FIND MORE DETAILS ABOUT THE PRODUCTS ON THIS PAGE, FEATURES AND BENEFITS AND THE 

CONTENTS OF DELIVERY ONLINE IN THE CCE DEALER STORE. 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 





V-Coil Thread Repair System 

V-COIL offers many practical thread repair sets for the following 

thread types: Metric, metric fine, UNC, UNF. 

The V-COIL thread repair sets include wire thread inserts 1.5xD 

length ex works. Wire thread inserts in the refill packs are 

available. 

• Application: 

• Thread Repair of damaged or worn-out threads 

• Thread Armour Plating for material with low shear strength 

• Recovery of rejected items 

• For new highly stable and long-lasting internal threads 

• Perfect for maintenance, installation and small series production 

• Wire Thread Inserts DIN 8140, tolerance ISO 2 (6H), Type S – free running, from stainless steel 

• Advantages: 

• Flexible application through more inserts and drills for the dimensions up to M12 

• High stock availability for standard and special dimensions 

• For thread cutting by hand 

• Higher load capacity after the repair by better thread properties, 

• Temperature and corrosion resistance 

• Attractive and functional presentation case 

V-COIL THREAD REPAIR SET V-COIL REFILL THREAD INSERTS 

Qty.: 1 

PART# DESCRIPTION QTY. 

PART# DESCRIPTION 

685784 1/4 UNC 100 

685774 1/4 UNC 

685785 5/16 UNC 100 

685775 5/16 UNC 

685786 3/8 UNC 100 

685776 3/8 UNC 

685787 7/16 UNC 100 

685777 7/16 UNC 

685788 1/2 UNC 100 

685778 1/2 UNC 

685789 1/4 UNF 100 

685779 1/4 UNF 

685790 5/16 UNF 100 

685780 5/16 UNF 

685791 3/8 UNF 100 

685781 3/8 UNF 

685792 7/16 UNF 100 

685782 7/16 UNF 

685793 1/2 UNF 100 

685783 1/2 UNF 

914368 M 3 x 0,5 - 1,5D 100 

914361 M 3 

914369 M 4 x 0,7 - 1,5D 100 

914362 M 4 

914370 M 5 x 0,8 - 1,5D 100 

914363 M 5 

914371 M 6 x 1,0 - 1,5D 100 

914364 M 6 

914372 M 8 x 1,25 - 1,5D 100 

914365 M 8 

914373 M 10 x 1,5 - 1,75D 100 

914366 M10 

914374 M 12 x 1,75 - 1,5D 100 

V-COIL thread repair set for 

914367 M 12 

923264 M 14 x 1,25 - 8,40mm 50 spark plug an o2 sensors 

923265 M 14 x 1,25 - 12,40mm 50 

685795 Spark plug thread repair 

m14x1,25 

923266 M 14 x 1,25 - 16,40mm 50 

685796 Spark plug thread repair 

923267 M 12 x 1,25 - 16,40mm 5 

m12x1,25 

923268 M 18 x 1.5 9.0mm 10 

914376 O2 Sensor 5EB M18x1,5 

914377 O2 Sensor 10B M18x1,5 

923269 M 18 x 1.5 9.0m, INCONEL X750 10

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

M3-M12 HSS-E VAP Hand Taps Set (set of 

22 pcs.) 

• VAP-coating for improved DIN 352 HSSE VAP Rougher 

adhesion of coolant and piloted - M 4 x 0.7 

lubricant 

• 1x Hand Tap set of 3 pieces 

• reduces tearing of the 

DIN 352 HSSE VAP Rougher 

lubricating filand the 

piloted - M 5 x 0.8 

formation of cold welding • 1x Hand Tap set of 3 pieces 

• Rougher piloted 




• wear resistant steel up to • 1x Hand Tap set of 3 pieces 

1400 N/mm² 


• high alloy steel 


• heat resistant steel 


• stainless steel 


• alloy tool steel 


• cast iron 


• Contents: 


• 1x Hand Tap set of 3 pieces piloted - M 12 x 1.75 

DIN 352 HSSE VAP Rougher • 1x Adjustable Tap Wrench 


Zinc die cast No. 1.1/2 



P.V.96 Round dies VX Set HSS-E VAP M3 – M12 


• Alloyed, tough material up 

to 1200 N/mm² 

• INOX (stainless steel) 

• Aluminium cast 

• Spheroidal cas iron GGG 


and machine 

• Benefit: 

• High cutting ability 

• Reduction of torque 

• Uninterrupted swarf flow in 

direction of feed 

• Prevents jaming of swarf 

• Steam tempered thereby 

optimal adhesion of cutting 

oil 

• Contents: 

• 1x Round Die DIN 223 (DIN 

EN 22568) HSSE VAP – M 3 


x 0.5 



x 0.7 



x 0.8 



x 1.0 



x 1.25 


EN 22568) HSSE VAP – M 10 

x 1.5 


EN 22568) HSSE VAP – M 12 

x 1.75 


VC381 V-COIL rapid Thread Repair Workshop 

Kit M5 – M12 


Drill, 8.3 mm 

• Thread Repair of damaged or • 1x V-COIL rapid STI-Twist 

worn-out threads 

Drill, 10.4 mm 

• Thread Armour Plating for • 1x V-COIL rapid STI-Twist 

material with low shear Drill, 12.4 mm 

strength 

• 1x V-COIL rapid STI-Taps, 

• Recovery of rejected items ForD, HSS-G, 5 x 0.8 

• For new highly stable and • 1x V-COIL rapid STI-Taps, 

long-lasting internal threads ForD, HSS-G, 6 x 1.0 

• Perfect for maintenance, • 1x V-COIL rapid STI-Taps, 

installation and small series ForD, HSS-G, 8 x 1.25 

production 

• 1x V-COIL rapid STI-Taps, 

• Wire Thread Inserts DIN ForD, HSS-G, 10 x 1.5 

8140, tolerance ISO 2 (6H), • 1x V-COIL rapid STI-Taps, 

Type S - free running, from ForD, HSS-G, 12 x 1.75 

stainless steel 

• 1x Tang Break Tools, No. 8 

• Assortment with the most • 1x Tang Break Tools, No. 9 

popular dimensions in an • 1x Tang Break Tools, No. 11 

attractive and functional case • 1x Tang Break Tools, No. 13 


• 1x Tang Break Tools, No. 15 

• application flexibility • 10x Wire thread inserts - type 

• All tools with 1/4“ hexagon S - free running M 5 x 0.8 – 

drive 

1.5 D 

• To be used by hand or • 10x Wire thread inserts - type 

cordless powertool 

S - free running M 6 x 1.0 – 

• No adjustment by hand while 1.5 D 

assembling 

• 10x Wire thread inserts - type 

• Handy, even in awkward S - free running M 8 x 1.25 

places 

– 1.5 D 

• More compact than the • 10x Wire thread inserts - type 

standard 

S - free running M 10 x 1.5 

• Higher load capacity after – 1.5 D 

the repair by better thread • 10x Wire thread inserts - type 

properties, 

S - free running M 12 x 1.75 

• Temperature and corrosion – 1.5 D 

resistance 

• 1x V-COIL rapid inserting 

• Same price as standardsystem 


tool, 5 x 0.8 

• Attractive and functional tool, 6 x 1.0 

presentation case 


• Contents: 

tool, 8 x 1.25 

• 1x V-COIL rapid STI-Twist • 1x V-COIL rapid inserting 

Drill, 5.2 mm 

tool, 10 x 1.5 

• 1x V-COIL rapid STI-Twist • 1x V-COIL rapid inserting 

Drill, 6.3 mm 

tool, 12 x 1.75 

• 1x V-COIL rapid STI-Twist 


LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


V-COIL VC80 Thread Repair Workshop Kit 


• Thread Repair of damaged or worn-out threads 

• Thread Armour Plating for material with low shear strength 



• Perfect for maintenance, installation and small series 

production 

• Wire Thread Inserts DIN 8140, tolerance ISO 2 (6H), Type S – 

free running, from stainless steel 

• Assortment with the most popular dimensions in an attractive 

and functional case 


• Flexible application through more inserts and drills for the 

dimensions up to M12 

• High stock availability for standard and special dimensions 


• Higher load capacity after the repair by better thread 

properties, 


• Best price 

• Attractive and functional presentation case 

• Contents: 

• 1x STI-Short machine tap HSS-G Form D M 5 





• 1x STI Twist drill HSS-G 5.2 mm 





• 1x Inserting and tang break tool no. 8 for M 5 





• 10x Wire thread inserts M 5 in 3 length (1.0 – 1.5 – 2.0 x 

diameter) 


diameter) 


diameter) 


diameter) 


diameter) 

Part#: 914359 , Field of Application: Thread Repair Set M5 

to M12 , Description: M5-M12 , Unit: Set , Qty.: 1 



V-COIL O2 Sensor 10E Thread Repair Set 


• For the simple and fast repair of defective oxygen sensor 

threads M18x1.5 



• With HexTap LS and LSN 

• With Wire Thread Inserts LS made from INCONEL X750 and/or 

Solid Thread Inserts LS from stainless steel 


• High stock availability 

• Higher load capacity after the repair by better thread 

properties, 


• Best price 

• Contents: 

• 1x HexTap LS, Multi-Drive, HSS-G, M 20 x 1.5 

• 1x HexTap LSN, Multi-Drive, HSS-G, M 18 x 1.5 

• 10x Wire Thread Inserts – LS made from INCONEL X750 M 

18×1.5 

Part#: 914375 , Field of Application: Thread Repair Set O2 

Sensor 10E M18x1,5 , Description: M18x1,5 , Unit: Set , 

Qty.: 1

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Cam Bearing Remover and 

Installer 

PART# 

FITMENT 

900903 Milwaukee Eight 17-23 

Valve Spring Compressor 

Collar Adapter 

PART# 

FITMENT 


Cylinder Hold Down Nuts 

PART# 

900905 

FITMENT 

Twin Cam 99-17, Milwaukee 

Eight 17-23 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

Left Main Seal Installer 

INTAKE 

PART# FITMENT 


Balancer Scissor Gear 

Alignment Screw 

Alternator Rotor Remover 

and Installer 

ENGINE 

PART# 

FITMENT 

PART# 

FITMENT 



GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

Main Bearing Remover and 

Installer 

PART# 

FITMENT 

900909 Milwaukee Eight 17-19 

Piston Pin Clip Remover and 

Installer 

PART# 

FITMENT 

900910 07-17 Twin Cam 110” engines 

Countershaft 1st Scissor Gear 

Alignment Tool 

PART# 

FITMENT 


WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

Fuel Tank Wall Mount 

PART# 

900912 

FITMENT 

Milwaukee Eight 17-23 For 

all fuel tanks with two front 

mounting tabs 

Axle Guide Installation Tool 

PART# 

900913 

FITMENT 

For all Models use 1” and 

25mm Axles 

Fork Cap Installation Tool 

PART# FITMENT 

900914 For all 49mm fork tubes 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 




Swing Arm Bearing Installer 

PART# FITMENT 

900915 02-23 Touring 

Mighty Bite Crankshaft 

Locking Tool 

PART# 

FITMENT 



2012 Twin Cam 02 Sensor 

Wrenches 

JIMS has just released two new 2012 

oxygen sensor wrenches. A must have to 

remove or install the O2 sensors without 

removing the exhaust pipes on the 

motorcycle. 

619285 Use on 12-17 Dyna, 12-23 Softail, 

12-17 V-Rod, Softail models only 

front O2 sensor 

619286 Use on 12-23 Softail rear O2 sensor 

Fork Cap Allen Socket 

PART# FITMENT 

900918 14-23 Touring, 14-23 Trike 

Wrist Pin Remover Adapter 

PART# FITMENT 


Head Holder 

PART# 


FITMENT 

00-23 Softail, 99-23 Touring, 

99-17 Dyna, 09-23 Trike 

Touring Model Fork Stem Nut 

Wrench 

Normally to get access to the top stem 

nut you would need to remove theradio 

package. With this tool you’re able to 

loosen, tightenand torque to spec. the 

1-1/2” stem nut without radioremoval 

and ultimatelysaving 45 minutes for an 

experienced Harley mechanic. 

619287 Use on 94-95 FLHR, 96-13 

Touring, except 96-13 Road Glide 

modelsFLHR. 

Engine Stand 

PART# 

FITMENT 

900917 17-23 Touring, 17-23 Trike 

Ballancer Bearing Remover for 

Milwaukee Eight 

The Milwaukee-Eight engine design 

incorporates balancers to reduce engine 

vibration. This tool can remove the 

balancer bearings in both Touring and 

Softail models without damage to the 

crankcase. 


Part#: 917609 , Fitment: 17-23 Touring, 

18-23 Softail, 17-23 Trike , Unit: Each 

, Qty.: 1 


Ballancer Bearing Installer for 


All Milwaukee-Eight engines (Softail and 

Touring)incorporate balancers to reduce 

vibration. JIMS has now developed a 

balancer bearing installer, which can be 

used in conjunction with the existing JIMS 

balancer bearing remover, to precisely 

install these bearings in the proper 

location for all Milwaukee-Eight engines. 

Incorrect installation of these bearings can 

cause severe damage to the crankcase,or 

even complete engine failure. This 

precision machined installer, aligns to 

the crankcase via case bolt and dowel 

locations, allowing the technician to install 

the bearings on a workbench without the 

use of a driver or press. 


18-23 Softail, 17-23 Trike , Unit: Each , 

Qty.: 1 

Fork Oil Level Tool 

• Use this tool to check and adjust the 

oil level on conventional and single 

chamber cartridge forks 

• Adjustable ring will measure oil levels 

from 0 to 300 mm in 5 mm increments 

• Syringe has a capacity of 60 ml 

• New plunger head design features 

two fluorocarbon elastomer X-Ring 

seals that provide superior sealing and 

chemical resistance 

• Billet aluminum plunger knob with 

durable black anodized finish 

• New plunger head design allows easy 

cleaning and replacement of seals 

Part#: 922058 , Unit: Set , Qty.: 1

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Twin Scan II by Daytona Twin Tec 

The new Twin Scan II provides diagnostic capabilities not found 

in other tools. It’s especially useful for diagnosing hard to find 

intermittent trouble codes. The motorcycle can be operated 

while the unit is installed. Under normal conditions (no trouble 

code), the unit will store data for the last hour of operation. If 

a trouble code is set, the unit automatically stops logging data 

30 minutes after the code is set. This allows you to examine data 

before and after the code was set, even days later. 

• Requires laptop PC for display, and includes Windows software 

• Reads and clears diagnostic trouble codes from ECU (engine 

control unit), TSSM (turn signal/security module), speedometer, 

and tachometer 

• Real time display of engine data on instrument panel type 

display 

• Built-in data logging 

• Stores up to one hour of data 

• Automatically triggers when a trouble code is set 

• Shows data before and after code is set 

• Includes two analog inputs for air/fuel ratio (AFR) 

Compatible with 01-17 fuell injected models using Delphi system 

(including V-Rod) with 1850 databus and 03-06 carbureted 

models with new 12 pin ignition module. Not compatible with 

11up Stoftail models, 14-up Sportster, 14-up Touring and 12up 

Dynas with CAN data bus. 


Push Rod Tool for HD 

• Designed to remove and install the clip on Harley-Davidson® 

collapsible push rod tubes on Twin Cam and earlier Models 

• Flat portion of tool fits under the cylinder head while cupped 

end fits over the bell in the tube and then compresses the 

spring allowing for easy access to the spring cap retainer 

• No more cut knuckles & scratched engine parts from using a 

screwdriver between the fins 

• New improved design with shoulder bolt pivot for smoothness 

and durability 


JIMS Engine Dipstick Socket Tool 

619298 Tool, engine dipstick socket 06-11 Dyna, 07-11 Touring, 

12 FLHTCUSE7, 12 FLHXSE3, 12 FLTRXSE 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

Dyna Ignition Switch Fork Lock Tool 

This tool is used to make removing and installing the Dyna 

ignition switch & fork lock simple. This tool locates on the 

ignition switch face nut that holds the switch in place on the 

frame, letting you remove or install this switch correctly. 

619302 Dyna 06-17 

JIMS Mega Nut For Cruise Drive 

By installing this mega nut correctly you can feel confident that 

your rear pulley will never come loose from your main drive gear. 

New for 2011, this nut is now available for late model Cruise 

Drive Transmission. 

619297 06-17 Dyna, 07-23 Softail, 07-23 Touring, 09-23 Trike 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Transmission Case Shifter Seal 

Installer 

These two simple tools make installing the 

shifter shaft seal precise and effortless. 

They align, center and install the shifter 

seal to the right depth on all EVO and 

Twin Cam Big Twin & Sportster models. 

619299 Use to install H-D seal No.37101- 

84B, 11000101 on 06-23 6-speed 

transmission and 84-05 Sportster 

619300 Use to install H-D seal No. 12045 

on all EVO Big Twins 80-99 or 

on H-D Twin Cam 5-Speed 99-06 

FXST, FLH and FXD -05. 

Jims Ignition Alignment Tool 

The professional technician needs fast and 

accurate alignment of the ignition switch 

cover. Fiddling with screwdrivers and coat 

hangers does not cut it! Our alignment 

tool is the perfect solution; correct 

alignment is quickly and easily achieved. 

This tool is for 2014 and later touring 

models and based on our proven design 

for earlier models. 

642290 Alignment tool for 14-23 HDI 

Touring models 

JIMS Outer Balancer Bearing 

Installer & Remover Tool 

This tool removes and installs the 

outboard balancer bearing on the new 

96” and 110” “B” Softail engine’s chain 

guide support plate. Sold each. 

622056 For all Softail models 07-17 



FXST Rear Seat Mounting 

Screw Tool 

The JIMS tool locates on the seat 

screw head to keep from scratching or 

damaging the rear fender, or screw, when 

installing or removing the seat. 

619301 Use on 07-23 Softail models 

using the H-D screw No. 3075 

Jims Angled Feeler Gauge 

This new innovative feeler gauge holder 

eliminates the need to use bulky multi 

feeler gauge tools while performing 

valve adjustments. This tool is ideal for 

reaching down into small tight areas 

and incorporates an angle to help 

reach around corners, often necessary 

for adjusting valves. Tool includes two 

handles with: .002”, .003”, .004”, .005”, 

.006” and .008” inserts. 

619304 Feeler Gauge Kit 

JIMS Ignition Switch Housing 

Alignment Tool 

This tool will easily align the ignition 

switch housing as the retaining screws 

are being torqued. This gives the ignition 

switch knob the alignment it needs to 

help extend the life of the ignition switch 

housing. Sold each. 

622051 For all FL models 03-13, V-Rod 

models 02-17 622051 

JIMS Balancer Shaft Removal 

Tool 

This tool is designed to remove both 

front and rear counter-balancer shaft 

bearing assembly from the left engine 

case on the new 96” and 110” Beta 

engines. Sold each. 

622058 For all Softail models 07-17 

JIMS Twin Cam Timken Case 

Bearing Conversion Tool 

This tool is a must for the big cubic inch 

late model Twin Cam engine builder. 

It may also be used to replace bearing 

for stock 88" or 96" engines. Utilizing 

the special JIMS precision insert, it is 

designed to easily and accurately convert 

the left side crankshaft roller bearing 

(H.D. No.24604-00D) to the more durable 

Timken Bearing (H.D. No.9028). This insert 

is manufactured from aluminum that is 

several times stronger than the aluminum 

case material the standard bearing rides 

in. The Tool Includes: 

• A new steel bearing insert held to under 

.0002” TIR (total indicator reading). 

• A press plate that will hold the bearing 

insert in line with the case bearing bore 

at the time it is being pressed into case. 

• All the necessary drill bits to drill oil 

feed and return holes, hardware, and 

detailed instructions. This job can be 

performed with normal hand tools, a 

hand drill, and a 2 ton press. 

*Order Bearing Inserts & Timken Bearings separately. 

640097 Tool for use on Twin Cam engines 

03-17 

640098 Stainless steel Timken case bearing 

insert kit

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

JIMS BETA Balancer Inner Bearing Remover/ 

Installer 

Accurately and safely install or remove the inner balancer 

bearing mounted in the left engine case. Designed for early or 

late Beta cases 00-17. 

622043 Beta cases 00-17 

JIMS Balancer Shaft Retention Pins 

Use this tool to secure the engine balancers on Twin Cam 88 “B” 

engines when servicing the flywheel assembly. This tool locks 

into the balancer’s sprocket pin holes to prevent the balancer 

from turning out of sync with the flywheel. 

671017 For Twin Cam 88 Softail models from 00-17 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

JIMS Balancer Shaft Alignment Tool 

This tool is a must-have for maintaining a long life of your 

balancer’s drive chains and bearings. It takes the guess work out 

of setting up your sprocket and chain alignment on both early 

and late Twin Cam Softail engine and checks chain alignment 

between balancers and crankshaft. 

671014 For all Twin Cam 88 and 96" Softail models from 00-17 

FL Power Train Alignment Tool by JIMS 

This tool easily and safely aligns the Power Train, (rubber 

mounted engine, transmission and the swingarm assembly) 

to the correct position as found on most touring models. 

Alignment service must be performed when the engine, 

transmission, or swingarm has either been removed or repaired. 

The safety in handling and performance of the motorcycle could 

be greatly effected without the accurate alignment this tool 

provides. 

640096 For use on 93-08 FLHT models 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

622063 622064 

FRAMES 

JIMS Fuel Pump Retainer Remover Tool 

This is a must use tool for removal or installation of the retaining 

ring otherwise you run the risk of developing a fuel leak. This 

tool safely removes the retaining ring holding the fuel pump. 

Use for quick and easy service of fuel filter and other fuel related 

parts. Sold each. 

622055 For all 08-23 Touring and 09-23 Trike models 


JIMS Twin Cam Engine Rotator Socket 

Use this tool to rotate the flywheel/piston assembly, with the 

engine still in frame or on a bench. This tool is used to rotate 

the flywheel assembly when doing pushrod adjustments, when 

building big inch engines, checking operating clearances such as 

piston to piston, or valve to valve. Can also be used to hold the 

flywheel assembly from rotating when torquing the cam drive 

sprockets retention bolts. This tool has been manufactured with 

a long socket design making it easier to use without the use of a 

1/2” drive extension on your 1/2” driver. For engine bench work 

we recommend the engine be bolted in a JIMS engine stand. 

Sold each. 

Caution: Not for use with air or electric impact, this 

tool is only guaranteed for use with hand drivers, “not 

impacts”. 

622063 For all 06-17 FXD & 07-17 FXST, & FL models 

622064 For all Big Twins 55-06 models (except 06 FXD) 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


JIMS Twin Cam Inner Cam 

Bearing Installer 

Use this tool to press in the two inner cam 

bearings on all Twin Cams 99-17 (replaces 

tool No.622038 & 20289). This tool has 

been designed to press from the letter 

side of the inner cam bearings. Putting 

all the pressure to the very outer wall 

of bearing shell, eliminates any damage 

to the bearings, cam, or cases. This tool 

will stop at the cases and set the bearing 

depth to .023” to .028” below the case 

surface. Use with JIMS tool, CCI part # 

622032 to remove bearings. 

622067 Twin Cam Inner Cam Bearing 

Installer 

Inner Cam Bearing Removal 

Tool 

Used to easily remove the inner cam 

bearing. Insert puller collet into the 

cam bearing I.D. Insert dowel pin, place 

remover body over collet, lube threads 

and with hand tools the bearing is pulled 

from case. This precision tool will also 

keep all pin bearings from falling into the 

engine case. 

622032 Fits all 06-17 Dyna's and all Twin 

Cam models 07-17 

Cam Assembly Tool 

Use to hold both cams in an upright 

position while lowering the cam support 

plate over both guides. This tool has 

a non-marring material, that will not 

damage any of the cam’s surfaces. 

622040 Fits all 06-17 Dyna's and all Twin 

Cam models 07-17 

Cam Locking Tool 

Permits the technician to lock the 

camshaft and crankshaft sprockets to 

properly remove, replace and torque the 

sprocket bolts. This tool is made from 

non-marring Delrin. Fits all 06 Dyna Glide 

and 07-17 Twin Cam models. Sold each. 

622030 Cam Locking Tool 

Cam Clearance Tool Cutter Bit 

Twin Cam Engines 

20143 Replacement cutter bit 

JIMS Cam Removal and 

Installer Tool 

This multi-function tool will remove and 

replace front and rear camshafts and ball 

bearings. It precisely holds the camshaft 

to insure a smooth press in and out of the 

support plate. 

20290 For Twin Cam 88 models from 

99-06 JIMS Cam Chain Tensioner Tool 

Used to unload pressure on the primary 

and secondary chain tensioners to 

assemble and disassemble cams. Also 

checks spring loads on chain tensioners. 


99-06 (except 06 Dyna) 

Zipper’s Cam Lobe Clearance 

Cutter 

Can be used with the engine in the frame. 

Bolts to the engine case across the cam 

cover face, and has an adjustable cutter 

powered by any 1/2" drill. The cutter 

provides additional clearance for the front 

intake cam lobe in the pinion race area. 

20143 Replacement cutter bit 



JIMS Camshaft and Crankshaft 

Sprocket Lock Tool 

Permits the technician to lock the 

camshaft and crankshaft sprockets to 

remove, replace and torque the sprocket 

bolts. Made from non-marring Delrin. 


99-06 (except 06 Dyna)

APPAREL 

20629 

20695 

SEATS & 

TOURING 

FOOT 

CONTROLS 

JIMS Cam Bearing Puller 

Once the cams are removed from the 

support plate, this tool will remove 

the bearing. Unlike a general purpose 

puller this tool was designed to remove 

the bearing straight with no slipping or 

binding. 


99-06 (except 06 Dyna) 

JIMS Cam Tools 

Bearing Puller 

Easily pulls the inner cam bearing without 

splitting the cases. It also keeps the rollers 

from coming out during removal. 

20695 Fits Big Twin models from 58-99 

(except Twin Cam 88 models) 

Cam Bushing Reamer 

Line reams cam cover bushings from 

inner cam bearing for a true centerline 

between the two dimensions. 



JIMS Inner Cam Bearing 

Installation Tool for Big Twins 

Smoothly presses the inner cam bearing 

to the right depth into the right-side case 

when both case halves are assembled. 

20774 For all Big Twin models from 

58-99 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

JIMS Cam Seal Installer/ 

Remover for Late Model Big 

Twins 

Install or remove cam seal without 

removing the cam cover. Easy-to-use tool 

pulls the seal and drives in a new one flat 

and square for a no-leak repair. The tool 

can also be used to remove the cam cover 

from the case. 

20762 For all Big Twins from 86-99 

(except Twin Cam) 

JIMS Cam Gear Remover and 

Installer 

This precision tool will remove the cam 

gear on any single cam Big Twin from 

70-99, and reposition it on another cam 

shaft in exactly the same spot. Pressing 

the gear on in the advanced or retarded 

position is also possible. Save time and 

ensure accuracy time after time. 


Motion Pro Degree Wheel 

Aluminum construction with a 6 3⁄4" 

outside diameter and a 6 mm center hole. 

Can be used on all motorcycles to check or 

set up ignition timing. May also be used 

on 4-stroke engines to check or alter cam 

timing. Sold each. 

5008092 Motion Pro Degree Wheel 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

JIMS Inner Cam Bearing 

Remover 

Designed like the version for Evolution 

models, it removes the bearing easily 

without any damage to the crankcase. 

This precision-built tool will also keep the 

pin rollers from accidentally falling into 

the crankcase. 


99-06 

JIMS Bearing Race Drivers 

Cam Bearing Driver 

Used to install inner cam bearing. Fits 

single cam Big Twins from 58-99. Sold 

each. 

20699 Replaces OEM 97272-60 

Driver Handle 

Handle for bearing drive tools. Sold each. 

20666 Driver Handle 

JIMS Piston Support Plate 

Using this tool will give you peace of mind 

when installing your rings and cylinders 

by providing a non-marring flat support 

to push the bottom of the piston agents 

as you install the rings and cylinder over 

the piston. 

671018 Use on all Harley-Davidson engines 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



JIMS Wrist Pin Remover Tool 

This simple tool can be used easily by one 

person. No need to get another technician 

to hold the piston while your drift the pin 

out. (99-06 Twin Cam) 

20287 99-06 Twin Cam (except 06 Dyna) 

JIMS Piston Ring Compressor 

Extra fine tooth ratcheting mechanism 

will compress rings in small increments 

without breaking. Includes six bands 

ranging from 2 7/8" to 4 3/8". 

400357 

Clear Long Timing Plug Tool 

894888 Fits Big Twin 70-98 

Connecting Rod Clamping Tool 

Holds rod when fitting piston pin bushing. 

Used on all V-twin models (repl. OEM 

95952-33). Sold each. 

400548 Connecting Rod Clamping Tool 

JIMS Wrist Pin Bushing Tool 

Removes and replaces the wrist pin 

bushing without removing the connecting 

rod from the crankcases. 


99-06 

Piston Ring End Gap Tool 

• Accurate tool to measure ring end gap 

faster 

• The flanged design allows the piston 

ring to fit squarely in cylinder bore 

every time 

• Each side of the tool is made for 

checking a standard size piston rings 

• For Twin Cam standard size pistons 

for 95” 103” or 110”, with 3.875” or 

4.000” bore 

890574 Piston ring end gap tool 



Cam Gear Gauge Pins 

These pins are used to properly determine 

cam and pinion gear sizes. Sold in pairs. 

24196 0.105"-diameter BT 54-89 

JIMS Cam & Pinion Gear 

Gauge Pins 

Use to check gear diameters when 

changing cams or pinion gears on single 

cam Big Twins ONLY. Sold in pairs. 

400362 Fits Big Twins from 54-89 (.105" 

pins) 

400363 Fits Evolution Big Twins from 

90-99 (.108" pins) 

JIMS Wrist Pin Bushing Tool 

Makes it easy to remove and install rod 

bushings on all models (except Twin Cam 

88 models). Complete instructions guide 

you through removal, selection of new 

bushing with the proper clearances, and 

installation. 

20169 Fits all Single Cam Big Twins up 

to 99. Fits 57-20 Sportster, 95-02 

Buell and 45” Flathead. 

JIMS Piston Pin Keeper Tool 

Makes piston pin retaining ring 

installation a snap. Fits stock piston pin 

retainers on Big Twins from 83-99 (except 

Twin Cam 88 models) and Sportster 

models from L85-20, 87-10 Buell (exc. 

1125). 


Piston Jet Test Stand 

If you plan to rebuild more than two 

Twin Cam engines and or lower ends 

- this tool pays for itself! 

• Clear the jet of all assembly lubes 

• Verify the PSI number the jet switches 

“on” 

• Visualize the spray pattern 

• For Twin Cam 99-17 

890569 Piston jet test stand

APPAREL 

SEATS & 

TOURING 

Tappet Pump Up Tester 

• Fill completely your standard size 

hydraulic tappets 

• Inspect them physically 

• With the help of a drill press, check for 

proper feel 

890568 For Twin Cam 

Magnetic Tappet Holding Tool 

• The new JIMS® Magnetic Tappet Holder 

easily holds the tappets in the tappet 

bores when changing or upgrading 

cams 

• Simply install the tool over the tappet 

cover and the magnets will magnetically 

hold the tappet in place while 

performing any cam chest work, a time 

saver for any technician 

• Designed to work on both Twin Cam 

and Milwaukee-Eight engines 

Part#: 923736 , Fitment: 00-17 Dyna, 

00-23 Softail, 00-23 Touring, 09-23 

Trike , Unit: Set , Qty.: 1 

Vacuum Tappet Pump up Tool 

Our popular and effective bleed 

technology that is found in the JIMS 

brake bleeding tool has now been 

applied to hydraulic lifters. A special jar, 

designed for vacuum, holds up to four 

hydraulic lifters in a convenient tray. 

Once vacuum is applied, bubbles can be 

seen escaping from the lifters until they 

are completely bled. Lifters are now 

ready to install. No more abuse of the 

starting system to pump up the lifters, 

and no risk of damage to the valve train 

by running the engine, even at low RPM, 

when lifters have not been fully bled. 

A detailed manual can be found here: 

https://www.jimsusa.com/wp-content/ 

uploads/2019/10/5532-IS.pdf. 

Part#: 917611 , Fitment: 86-20 

Sportster, 85-94 FX Model, 91-17 

Dyna, 84-23 Softail, 85-23 Touring, 09- 

23 Trike , Unit: Each , Qty.: 1 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

Mini-Valve Spring Tester 0 to 

1000 P.S.I. Gauge 

Use this tool in either a bench vice, arbor, 

hydraulic screw press or a drill press. Tool 

fits any dual rate or conical valve spring 

with an O.D. no larger then 1.6” diameter. 

Precision gauge comes with a protective 

rubber boot. 

890572 Mini-valve spring testerC 

Tappet Adjustment Tool 

• This hand tool simplifies the way to 

verify proper tappet adjustment 

• Use on most hydraulic tappets, OEM 

and aftermarket 

• For Twin Cam, Evo, Milwaukee Eight 

890567 Tappet adjustment tool 

JIMS Head Holder Adapters for 

7mm Valve Guides 

The JIMS head holder tool makes pressing 

valve guides in and out simple. 

622185 7mm Assembly Pilot 

622186 7mm Insert 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

Interconnect Seal Leak Testing 

Tool 

• Inspect properly your lower end 

assembly before sealing the cases 

• It checks the sealing of the interconnect 

seal OEM 45359-00 

• For Twin Cam engines 00-17 

890570 Interconnect seal leak testing 

tool 

JIMS Wrist Pin Reamers 

Use with rods in or out of motor. These 

tools will ream your wrist pin bushings to 

OEM specifications, and are made to exact 

tolerances with pilots to locate from the 

I.D. of your wrist pin bushings. They are 

easy to use with their lead-in taper at the 

start of each ream. 

22320 Fits all single cam Big Twins from 

36-99 (including all aftermarket 

engines) 

JIMS Cylinder Torque Plates 

Required to accurately bore late-model 

aluminum cylinders. Simulates stress 

deformation of installed cylinder. Drilled 

for multiple applications up to a 4"-bore. 

The plates for Twin Cam 88 models also 

fit Screamin‘ Eagle big bore cylinders. 

Optional bolts are available for use with 

Evolution Sportster and Buell cylinders. 

20806 For Shovel and EVO 3.4375" to 

4" 66-99 

20291 For Twin Cam and 4.00" to 4.60" 

99-17 

20807 Optional bolt kit for use on 86-20 

Sportster and 95-02 Buell used 

with CCE 20806 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



622180 

622181 

JIMS Top Center Case Bolt 

Spot Facer Tool 

Added insurance when building a big 

bore Twin Cam engine. You have seen 

the center right case bolt thread that has 

become compromised from the larger 

cylinder spigot bore diameter? Now 

you can get back all the necessary case 

bolt retention by installing one of JIMS 

Through Bolts Kits. This tool is needed to 

spot face the right case so the bolt head 

will seat flat on the case surface. Use on 

all Twin Cam 99-17. 

622180 Case Bolt Spot Facer Tool 

622181 Center Through Bolt Kit 

JIMS Oxygen (O2) Sensor 

Wrench 

This tool is a must for removing and 

installing H-D’s new 4 wire heated Oxygen 

Sensors. The new fragile O2 sensor must 

be torqued to 14 ft-lbs, lending to the 

design of this tool to be used with a 3/8” 

drive torque wrench. 

622187 Use on 12-17 Dyna, 12-17 Softail, 

10-16 Touring 622187 

Valve Guide Driver Set 

3 piece driver set for valve guide 

installation and removal on Big Twin and 

Sportster models. Includes drivers for 

5/16", 11/32", and 3/8" I.D. guides. 

400562 

JIMS Exhaust Gasket (Seal) 


No longer do you need to fight trying 

to install this fragile exhaust seal. You’ll 

never worry about an exhaust leak again. 

Tool can be used with exhaust flange 

nuts, or JIMS handle CCI No. 20666 sold 

separately. Either way will position the 

seal evenly into the exhaust port of head. 

622182 Use on all 84-23 EVO Big Twins, 

XL, and all Twin Cam models, 


JIMS Exhaust Stud Drill Plate 

Guides and aligns the drill bit when 

removing broken exhaust studs. Use with 

a tap after to clean the threads. Can be 

used in the frame. Includes drill bit. 

20940 For Evolution and Twin Cam 

models 

JIMS Pushrod Cover Clip 

Installing and Remover Tool 

Made from black delrin, this tool will 

NOT marr or slip – and will install the 

clip professionally with just one hand in 

seconds! It’s a luxury tool that you will 

appreciate for years to come. 

622184 Use on all V-Twins that use pushrod 

clips.Ç 

JIMS Valve Spring Compressor 

Designed specifically for the heads on 

Evolution models, but will work with all 

Big Twins. It features a hardened ball 

bearing at the valve head end to eliminate 

damage to valves. Comes with new valve 

collar receiver for safer tool usage. 

20696 For all Evolution Big Twin and 

Sportster engines 

Valve Spring Compressor Tool 

Use this collar with CC #20696 to remove 

and replace valves and conical (beehive) 

springs. A must-have tool for safe valve 

work. 

622039 Fits all 04-20 Sportster, 05-17 Twin 

Cam and 04-10 Buell models, 

except CVO models 



Oxygen Sensor Socket Tool 

This tool is used to remove or install the 

oxygen sensor on all closed loop fuel 

injected H.D. models. Socket has a 3/8" 

drive receiver or can be used with a 7/8" 

wrench. Socket will withstand up to 125 

ft/lbs of torque. 

640091 For use on all EFI models 06-11 

(except 10- touring) 

JIMS Head Bolt Torque Gauge 

for Evolution Engines 

Allows the measuring of 90° when 

tightening head bolts. Torque sequence 

laser-etched on gauge. 

20805 For all Twin Cam, Evolution and 

Sportster engines from 84-17

20716 

APPAREL 

SEATS & 

TOURING 

20676 

FOOT 

CONTROLS 

JIMS Valve Guide and Seal 

Tools 

Precision tools permit accurate installation 

of shoulderless valve guides and seals. 

20676 For installation of shoulderless 

valve guides to the proper depth 

on all Big Twin models 84-04 

with .560” Dia. guides, including 

aftermarket heads. Use with 

installer tool 20716 below. Sold 

each 

622048 For all Big Twins 05-17 with 7mm 

valve guides, Sportster 04-20, 

Buell 04-10 (except 1125 models, 

Touring 17). Use with handle 

622047 below. Sold each 

Shoulderless Valve Guide Removal 

Tool and Installation Tool Handle 

Used to remove shoulderless valve guides 

and with above tools for installation. 

20716 For all Big Twins to 04. Sold each 

622047 For all Big Twins 05-17 with 7mm 

valve guides, Sportster 04-20, 

Buell 04 -10 (except 1125 models, 

Touring 17). Use with 622048 

above. Sold each 

JIMS Pinion Gear Puller 

Used to remove the pinion gear on all 

Big Twin and Sportster models (except 

Twin Cam models). May also be used to 

install pinion gear on Big Twin 39-89 

and Sportster models from 57-76. Collar 

included. 

20698 Replaces OEM 96830-51 

JIMS Pinion Bushing Puller 

Removes pinion bushing from cam cover 

in one easy operation. 

20445 For Big Twins from 54-99 (exc. 99 

Twin Cam) 

JIMS Rocker Bushing Reamer 

Precision reamers made from the finest 

heat-treated tool steel, and accurately 

dimensioned to exacting tolerances. Used 

for precision alignment and sizing of 

rocker bushings. 

20692 For 66-17 Big Twin, except 17 

M8, 57-20 Sportster, 95-10 Buel, 

except 08-10 1125 

JIMS Tappet Block Alignment 

Tool 

Used to make sure the roller tappet tracks 

on the center line of the cam lobe. 

20670 Fits Big Twins from late 77-99 

(exc. 99 Twin Cam) 20670 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

JIMS Gear Shaft Nut Socket 

Wrench 

Secures the pinion gear nut to the pinion 

gear shaft. Fits Big Twins from 55-92. 

20690 Replaces OEM 94555-55A 

WHEELS, TIRES 

& BRAKES 

FRAMES 

JIMS Rocker Bushing Puller 

Removes rocker arm bushings or roller 

bearings in one easy operation. 

FORKS & 

SHOCKS 

20446 For Big Twins from 66-17 (except 

Touring 17) and Sportster or 

Buell models from 57-20(exc. 

Buell 1125) 

SHEETMETAL 

JIMS Pinion Gear Lock Tool 

Locks pinion gear, necessary to torque 

the pinion nut. Tool screws to case and 

holds pinion gear stationary. 

20785 For Big Twin models from 54-99 


S&S Compression Release 

Socket Kit 

Special two-piece compression release 

socket kit permits in-frame installation of 

S&S compression releases while protecting 

wiring from damage during installation. 

601711 Two-piece socket kit 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Tappet Guide Puller for 

Sportster Models 

Removes press-fit tappet guides from the 

crankcase after tappet body adjusting 

screw is removed. Fits Sportster models 

from 57-78. 

20104 Replaces OEM 95724-57 

JIMS Sprocket Shaft Tools 

For installing the crankshaft into the 

crankcase Timken bearing. 

For Big Twin Models 

20116 Fits Big Twins from 55-02 

Sprocket Shaft Seal Tool 

Used with CC #20116 to press oil seal over 

sprocket shaft into the case. 


JIMS Rod Lapping Tool 

Fits Big Twins, Sportster and K models, 

45" and Indian rods (except Twin Cam 88 

models). Includes arbor assembly, 1.500" 

lap for 45", Indian and some case races. 

1.625" lap for Big Twin, Sportster and K 

model rods. 

26409 Lapping tool 

20727 

20666 

Motion Pro Tappet Tool 

Removes and fastens the tappet oil filter 

screen cover without removing exhaust on 

some models, and avoid scratching your 

engine cases. Sold each. 

• Includes O-ring to retain it in a 7/16" 

wrench or socket drive 

• Hex 7/16" drive allows more rotation 

before contacting cases 

• Flange design allows downward force 

to be applied to tool 

• The tappet oil filter screen is required to 

be serviced at every oil change 

• Fits all Big Twins (except Twin Cam 

88) with slotted screw tappet oil filter 

screen cover 

640110 Tappet Tool 

JIMS Snap Ring Installation 

and Removal Tool 

Removes and installs the Timken bearing 

outer race snap ring. A must for replacing 

rings in cases without inserts. No more 

gouging the aluminum surrounding the 

snap ring. 


JIMS Sprocket Shaft Bearing 

Race Tools 

Bearing Race Remover and 

Installation Tool With Race Tool 

Spacer 

Use with bearing driver tools to apply 

outward pressure to grip the race for 

easier installation and removal. 

20727 For CC #20688 and #20689 - For 

73-99 Big Twin, Sportster and 

87-99 Buell. Sold each. 

Sprocket Shaft Bearing Race Tool for 

Big Twins 

Used to remove and install Timken 

bearing race in motor case. 


Sprocket Shaft Bearing Tool for 


Used with to remove and install Timken 

bearing race in motor case. 

20689 Fits 77-03 Sportster, 87-03 Buell 

models 

Driver Handle 

Handle for bearing drive tools. 

20666 Driver Handle 



JIMS Flywheel Timken Bearing 

Remover 

Used to remove Timken bearings from 

sprocket shafts without re-moving shafts 

from the flywheels. 

22303 Fits stock flywheels on Big Twins 

from 86-02 

20459 Fits stock flywheels on Big Twins 

from 55-85, and aftermarket flywheels 

from 55-02 22303 

JIMS Drill Jigs for Precision 

Bushing Dowel Pin Location 

These drill jigs ensure exact factory 

bushing dowel pin location when building 

performance engines. Supplied with jig 

and drill bit. 

20623 For pinion bushings on Big Twins 

from 54-92 

JIMS Flywheel Sockets 

Low profile, yet provide 100% nut 

coverage. The socket end is machined flat 

to eliminate rounding-off the flywheel 

nut. Made from 4130 chrome-moly and 

heat-treated for strength. 

20634 1 5/8" x 3/4" drive for sprocket 

shaft nut on Big Twins from 

72-99 (except 99 Twin Cam)

APPAREL 

SEATS & 

TOURING 

JIMS BETA Case Support Block 

Tool 

Supports the left engine case while 

servicing the inner balancer bearings or 

other engine work. Blocks attach to the 

outer side of the engine case underneath 

the balancer bearing pads surface. 

Includes aluminum construction and an 

inserted Delrin pad that rests against the 

case to prevent marring. Blocks properly 

support the case, keeping it on a level 

plane when using a press for bearing 

service work 

622044 Beta Softail Twin Cam models 

00-17 

JIMS Timken Bearing 

Simulator 

Designed to allow quick and easy removal 

and replacement of the flywheel in the 

left-side crankcase. Permits checking 

of rod-to-case, piston-to-flywheel and 

cylinder-to-flywheel tolerances. 


JIMS Crankshaft Removing 

Tool 

Use to press crankshaft/flywheel assembly 

from cases and press case halves apart and 

break sealant bond. Hard cap, available 

separately, is needed for some pressing 

operations on end of sprocket shaft. For 

55-06 Big Twins (except 06 Dyna). 

20458 Crank assembly removal tool 

20815 Sprocket shaft hard cap 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

JIMS Compensating Sprocket 

Wrench 

New design tool is compact and easier to 

store in toolboxes. Requires a 1/2"-drive 

ratchet or breaker bar. 

20423 Fits FL models 55-E70 and 

Sportster models from 57-76 

JIMS Rod Race Tool 

Supports both sides of the rods while the 

races are removed or replaced, minimizing 

the possibility of distortion to female rod 

or race. 

20000 Fits all 69-99 Big Twins, 

Sportsters, 87-99 Buell (exc. Twin 

Cams) 

Crankshaft Turning Tool 

Splined socket engages the sprocket shaft 

to turn the crankshaft when the primary 

drive is disassembled. Especially useful 

during engine assembly to set ignition 

timing, check cam timing and valve-topiston 

clearance. 

20268 Fits sprocket shaft splines on all 

Big Twins from 66-99 (exc. Twin 

Cams) 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

JIMS Timken Bearing Race 

Installer 

Installs bearing races square and true in 

the left crankcase. A must for late engine 

cases. 

20820 For Big Twins from 69-02; 

Sportster 77-03 and Buell models 

from 87-02 

JIMS Crankshaft Guide 

This tool will spread crankcase pinion 

bearing rollers while reassembling right 

side engine case onto the flywheel 

assembly. 

400392 Fits all Twin Cam models from 

99-17, 04-09 Spotster, 03-09 Buell 

XB9R, XB9S 

Crankshaft Trueing Stand 

Custom Chrome’s own trueing stand for 

all Harley motors. Combines outstanding 

value with full-function features, 

including 10" right-hand swing, 6" lefthand 

swing and 18" center-to-center 

capacity. Full 80 lbs. pro grade unit is 

sold complete, and fitted with beam 

indicators, accurate to .002". 

24342 Flywheel trueing stand 

Note: Does not ship free freight. Shipping weight 101 lbs. 

24327 Replacement live center 

24328 Replacement dead center 

24344 Replacement handle 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



JIMS Wrist Pin/Rod Alignment 

Tool 

Checks rod straightness without removing 

rods from case. Measures 4 1/2"-long. 

20298 Fits all single cam Big Twins ONLY 

(including aftermarket and S&S) 

Flywheel ‘Jam’ Tool 

Holds the crankshaft in the TDC (topdead-center) 

position when installing 

cams. It threads into the cases in place 

of the timing hole plug and permits 

you to snug it up to the flywheels with 

the timing mark showing through its 

hollow center. It was designed for use on 

Sportster engines which have a tendency 

to rotate past TDC when changing cams, 

but it may also be used on Big Twins. 


JIMS H-D Cruise Drive 6-Speed 

Maindrive Gear Remover Tool 

Removes the main drive gear from the 

main bearing correctly while in the 

transmission case. Eliminates the need of 

an arbor press and the risk of case damage 

622054 Fits all 6-speed 06-17 Twin Cam 

and 17-23 M8 models 

Rod Alignment Tool 

• Use to check rod straightness without 

removing rods from case 

• The alignment tool is 4-1/2” long 

• Use on all Twin Cam A and B (Includes 

aftermarket motors) 

• .927” Wrist Pin 

890573 Rod Alignment tool 

JIMS H-D Cruise Drive 6-Speed 

Maindrive Gear and Bearing 

Remover / Installer Kit 

Complete Kit for servicing the main drive 

gear or the main bearing on the latest H-D 

6-speed transmission. Removes or installs 

both parts correctly without damaging the 

case. 

622057 All Twin Cam H-D 6-Speed Cruise 

Drive models, 06-17 Dyna's and 

all 07-17 Twin Cam models 

JIMS Starter Jackshaft Seal 


This tool is designed to easily align and 

install the starter jackshaft seal (H-D 

No.12066) without distorting or damaging 

the seal. This seal is located in the upper 

part of the inner primary of Big Twins. 

Sold each. 

622059 For all Twin Cam FL models 99-06, 

FXST models 00-06 & FXD models 

99-05, and on all Big Twin EVO 

94-00 

Clutch Adjuster Nut Tool by 

Motion Pro 

• For use on all 98-17 Big Twin models 

excluding applications with hydraulic 

clutches 

• Deep socket allows tool to recess 

into clutch basket and can be driven 

with 11/16” combination wrench or 

adjustable wrench 

• Through hole allows access with hex 

wrench to hold clutch adjuster screw 

while simultaneously tightening the 

adjuster lock-nut 

• Heavy duty tool for shop or home use 

• Compact design fits easily in the saddle 

bag or tool roll 

641128 Clutch Adjuster Nut Tool 



Mainshaft Mainshaft Seal 

Remover 

The Milwaukee Eight has a new 

crankshaft oil seal that is difficult to 

remove without potentially damaging 

the crankcase bore. This new unique and 

exclusive JIMS tool is designed to do the 

job right, with no chance of damage to 

the case. Simply insert the removal fingers 

over the engine output shaft, and then 

slide the lock collar over the fingers. Once 

assembled, you can easily remove the seal 

square to the bore by simply turning a 

wrench. 


18-23 Softail, 17-23 Trike , Unit: Each 

, Qty.: 1 

JIMS Inner Primary Cover 

Bearing and Seal Installer/ 

Remover Tool 

Designed to safely remove and install 

the inner primary bearing, (H-D No.9135) 

without any damage to the new bearing. 

This is done by pushing on the outer 

perimeter of the bearing. Also removes 

and installs inner primary seal, (H-D 

No.12052A). This is the bearing and seal 

that the transmission mainshaft passes 

through. Sold each. 

622060 For all Late 84-05 Softail models, 

85-06 Touring models and 85-05 

FXR & Dyna models

APPAREL 

SEATS & 

TOURING 

JIMS Flywheel Runout 

(Trueness) Inspection Gauge 

Check flywheel runout of the pinion 

shaft while assembled in engine case. 

Also check the amount of gear lash on 

gear driven cams used in some twin cam 

engines. By using a JIMS tire rotator 

No. 936 you can remove most all of the 

stress being applied to the flywheel by 

not rotating the engine with the electric 

starter motor. 

Main Drive Gear Bearing and 

Seal Installation Tool 

Use this tool to safely install new main 

drive gear bearings and seal, with use 

of a small 1-ton press. This tool will hold 

bearings and seal square to its bore, 

eliminating any marring of the bearings 

and seals and installing both to the right 

depth. 



Transmission Main Drive Gear 

Tool 

Use to remove the large 2 1/4" hex nut 

from the end of main drive gear, which 

secures the rear drive trans pulley. Just 

thread the inner support collar to end of 

mainshaft, place the socket over the collar 

with a 1/2" drive tool, and unthread (right 

hand thread) the locknut. 



FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

622183 Use on 70-17 Big Twin, Shovels, 

EVO and Twin Cam 

EXHAUST 

Gasket Locator Tool No. 968 

by JIMS 

This tool will assist you in aligning the 

gaskets to avoid misalignment and oil 

leaks. Primary cover, cam cover, and 

transmission end cover gaskets are just a 

few of the possible applications. Install the 

locator tools into the gasket surfaces 1/4”- 

20 threaded holes, slip on the gasket and 

the cover over the pins. Next, install a few 

cover mounting screws and snug down. 

Recover the tools and finish off with the 

remaining screws. 3 piece set. 

Transmission Door Removal 

Tool 

Use this tool to remove (pull) the complete 

door with gears and shafts from the 

transmission. Just prepare the trans for 

disassembly, bolt this tool to the outside 

of door, and place the two supplied press 

pins into the two screw holes of trans 

case. Thread in two of the screws, securing 

the door to cases, and the door is pulled 

from case. 



Primary Chain Locking Tool 

Use to lock the clutch hub sprocket to 

the front engine sprocket. With the two 

sprockets locked together, engine and 

clutch nuts can easily be removed and 

retorqued. 

622035 Fits all 06-17 Dyna and 07-23 

Softail models 

Primary Drive Lock Tool 

894889 With step fits all models 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

640094 For use on all models with 1/4”- 

20 threaded gasket surface 

mounting holes 

FRAMES 

JIMS 6-Speed Twin Cam Main 

Drive Gear Seal Installer 

This tool is designed to properly align 

and install, to the right depth, the main 

drive gear seal H-D No.12077 into the end 

of the gear. This can be performed while 

the assembled transmission is either on a 

bench or in the motorcycle chassis. Sold 

each. 

622062 For all 6-speed 06-17 Twin Cam 

and 17-23 Milwaukee Eight 

Cruise Drive (Late 6 Speed 

Trans) Main Case Seal Installer 

H-D’s new 6-speed transmission is a very 

stout piece of engineering, incorporating 

some of the best bearings made. These 

main case bearings are of such high 

precision that you must be very gentle 

when working in or around them. For this 

reason, JIMS has developed a driver style 

seal installer (not a pushing or pulling 

type, which could damage these bearings). 

This new tool installs the main seal to the 

correct depth, without applying any stress 

to the new precision bearings, or new 

seals. 

622190 Fits all 6-speed 06-17 Twin Cam 



JIMS Primary Locking Bars 

To lock primary for service work. 

20824 For 4-speed Big Twins and 

5-speed Softail models 

20825 For 5-speed FXR and FLT models 

20826 For 91-20 Sportster and 95-10 

Buell, except 08-10 1125 models 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


JIMS Shifter Fork Gauges 

These American-made tools are ideal 

for setting and aligning shifter forks. Fit 

4-speed Big Twin models from 39-86. 

20001 39-E79 (repl. OEM 96384-39) 

20108 Late 79-86 (repl. OEM 96385-78A) 

JIMS 5-Speed Main Drive Gear 

Tool 

Used to remove and install the main drive 

gear and it’s bearing without removing 

the transmission. 

20679 Fits Big Twins from 80-06 and 

Sportster models from 91-05 

(except Dyna 06) 

Side Case Cover Puller 

• Use to remove the right side-case cover 

• Will fit late model Harley-Davidson 

motorcycles, including all 70-99 Big Twin 

models and 90-19Sportster and 95-02 

Buell models 

• Includes bracket, puller bolt and set 

screws 

• Made in the USA 

5008153 Side Case Cover Puller, Sold each 

JIMS Mainshaft Sprocket Nut 

Wrench 

Extra-long, two-piece design with inner 

collar that keeps the wrench on the nut 

for safer service work. 1 7/8" hex (repl. 

OEM 94660-37A). 

20691 Fits Big Twins from 36-06. Except 

06 Dyna. 

JIMS Primary Drive Lock 

Black Delrin plastic tool wedges between 

the primary chain and motor sprocket. 

20823 For all primary drives 

JIMS 5-Speed Main Bearing 

Remover 

Removes the bearing straight without 

damaging the transmission case. Can be 

used without removing the case from the 

frame. 

20947 For 5-speed Evolution Big Twin 

models 80-06 

Compression Tester with 10, 

12 and 14 mm Adapter 

• Helps you to quickly and easily inspect 

engine compression on both 4-stroke 

and 2-stroke engines 

• Redesigned and Improved billet gauge 

manifold with integrated pressure 

release valve 

• Easy to read precision 0-300 psi analog 

gauge with protective rubber boot 

• Hose and adapters included for 10 mm, 

12 mm and 14 mm spark plugs 

• Integrated quick disconnect fitting for 

easy hose installation and removal 

• Nylon storage pouch 

PART#: 920434 , UNIT: EACH , QTY.: 1 



JIMS Trapdoor Puller 

Removes trapdoor with gears and shafts 

attached. Will not damage door bearing. 

20835 For 5-speed Big Twin transmissions 

from 80-06, (exc. 06 Dyna) 

JIMS Mainshaft Bearing Race 

Tool 

Used to remove and install the bearing 

inner race on the transmission mainshaft. 

20677 Fits Big Twins from 84-23

APPAREL 

SEATS & 

TOURING 

641115 

Mainshaft Sprocket Locknut 

Wrench 

Use this wrench to install or remove the 

countershaft sprocket nut. Fits all Big Twin 

models from 36-E84. 


JIMS Clutch Puller Tool for 


24154 Fits 71-E84 Sportster models 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

641116 

Mini Bleeders by Motion Pro 

• Combines wrench and bleeder valve 

into one convenient and compact tool 

• Bleeds brake systems and hydraulic 

clutch systems 

• Internal check valve for fast easy 

bleeding 

• Anodized billet aluminum handle with 

chromoly steel body 

• Compact size for tight spaces 

• High quality internal seal 

• Multi position handle. 

641115 Mini bleeder 8mm 

641116 Mini bleeder 10mm 

Primary Case Tools for 


Precise replica of OEM “Kent -Moore” 

primary plug tool. Used with standard 

3/8” drive ratchet to install and remove 

slotted primary plugs on Sportster models 

from 71-85. Works on plugs with flat or 

concave bottoms. Sold each. 

400452 Fits Evolution Sportster models 

from 86-90 

JIMS Diaphragm Clutch Spring 

Compressor Tool 

Used to release clutch spring for ease of 

retainer ring removal and installation. Fits 

Big Twins from 90-97. 

20686 Replaces OEM 38515-90 

Motion Pro Clutch Tool 

Designed to hold clutch baskets, 

flywheels, gears, sprockets, etc. Jaws open 

to 5 inches wide. Made of medium carbon 

steel with hardened jaws. A very useful 

tool for holding any kind of mechanical 

work. 

5008008 Clutch Tool 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

Ergo Spoke Wrench by Motion 

Pro 

• Unique combination wrench design has 

3-sided open end and semi-closed end 

• Use open end for quick adjustment of 

spoke nipples and semi-closed end for 

those hard to turn nipples that require 

more torque 

• Specially designed ergonomic handle 

allows larger turning radius and 

excellent grip and feel 

• Polished finish with laser engraved logo 

and size markings 

• Limited life time warranty 

• Patent pending 

641127 Ergo spoke wrench 6mm 

JIMS Clutch Lock Plate for 

Early Big Twins 

Locks clutch hub to shell to remove or 

install clutch hub nut. Most effective when 

used with primary locking bars sold below. 

20827 Fits Big Twins from 41-E84 

Motion Pro Clutch Spring 

Compression Tool 

Made for compressing the diaphragm 

clutch springs on Big Twins from 90-97 and 

Sportster models from 91-03. 


FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



14965 

14966 

Clutch Hub Puller for Big Twins 

Pulls three-finger clutch hubs on all Big 

Twin models from 36-E84. Puller also 

includes four bolts for use with the puller 

to remove the clutch hubs on late-model 

Big Twins with diaphragm clutches thru 

36-89. 

20006 Replaces OEM 95960-52C 

Barnett Diaphragm Clutch 

Spring Compressors 

Facilitates the removal and re-installation 

of the clutch plates on wet clutch models. 

Two different versions are available. 

14965 Fits all Big Twins from 90-97, and 

all Sportster models from 91-03 

(repl. OEM 38515) 

14966 Fits all Sportster models from late 

84-90 (repl. OEM 34761) 

Motion Pro Hydraulic Brake 

Bleeder 

Aids in bleeding and servicing of hydraulic 

brakes. The unique check valve allows 

fluid and air to escape, while preventing 

air from re-entering the system. 

Instructions and hose included. 

5008143 Hydraulic Brake Bleeder 

Clutch Hub Puller 

A tool that belongs in the toolbox of 

everyone that likes to turn his own 

wrenches on Big Twins. Made in America 

out of top-quality tool steel. 


BDL Clutch Lock Up Tool 

For use on all of our belt drive units which 

have the BDL round clutch dogs. This 

clutch lock-up tool is designed to help 

you properly torque the clutch basket & 

hub assembly to the main shaft of your 

transmission without the use of an Impact 

wrench that can damage the hub, basket 

or other components of your new belt 

drive. 

612434 Clutch lock tool for BDL drives 

Chain Alignment Tool 

• Quick and accurate alignment 

• Tool body clamps squarely to rear 

sprocket so the alignment rod will 

indicate sprocket alignment to chain 

• Made in the U.S.A 

5008048 Chain Alignment Tool, Sold each 



Clutch Hub Puller 

Pulls the clutch hub on Big Twin and 

45" models. Works with 3, 5 or 10 finger 

clutch hubs. Also pulls the motor sprocket 

on Sportster and Big Twin models, 

Sportster transmission sprockets and the 

rotor assembly on Big Twin models from 

70-89. 


Motion Pro Chain Riveting 

Tool 

Designed to rivet chain links to form an 

endless chain. It can be used on drive 

chains, or as a chain breaker by pushing 

the pin out. Each kit includes three 

pin sizes to fit a variety of chains with 

replacement pins and tips available. 

5008058 Riveting tool 

5008059 2mm replacement pin 



Motion Pro Quad Stake Chain 

Rivet Kit 

Use in conjunction with the Motion Pro 

Jumbo Chain Tool. This rivet kit will quad 

stake chain, so it looks like a factory job. 


Motion Pro Masterlink Pliers 

• Simplifies installation and removal of 

clip-type masterlinks 

• One tip is shorter and notched to be 

placed on the pin while the other is 

longer to easily push the clip 

5008230 Master Link Pliers

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Master Link Installation Tool 

Turns the chore of installing press-fit 

master link plates into an easy job. Works 

equally well on both standard and O-ring 

chains. 

HAND 

CONTROLS 

20274 Master Link Installation Tool 

JIMS Cleveblock Spreader 

Used to install the swingarm in 5-speed 

rubber mount frames. When cleveblocks 

are replaced they need to be positioned to 

installing the rear of the transmission. This 

tool spreads the cleveblocks permitting 

installation of the swingarm. 

20951 For 82-94 FXR, 80-01 

Touring 20951 

JIMS Steering Head Bearing 

Race Installer 

Used to install steering head races, stock 

and custom as well as install cups in the 

frame. This tool pulls the races and cups in 

straight and true without damage. 

20950 For Big Twin models from 36-23, 

except 14-23 Touring, Trike, 78-20 

Sportster 

LIGHTING 

ELECTRICAL 

EXHAUST 

Motion Pro Mini Chain Press 

Tool 

Tool box size and budget priced tool for 

the installation of press-fit side plates. 

Very easy to use, and easily fits into tool 

kit. Hex key wrench is included. 

5008070 Fits all 520 to 530 chains 

Diamond Chain Breaker 

Compression screw uses a heat-treated 

steel tip to press out chain pins. It’s 

recommended that pins be ground 

off flush to avoid damaging the chain 

bushing. 

33037 Replaces OEM 94480-89T 

Motion Pro Jumbo Chain Tool 

Kit 

• Ultra heavy duty tool for breaking and 

riveting roller chain 

• Fits all 520, 525, 530 and 630 standard 

or O-ring chains, plus industrial chains 

from #50-#80 

• Pushes the pin completely through the 

chain link and rivets the same size chain 

with the included rivet adapter 

• Tool body may be mounted to a work 

bench for production work, held in a 

vise or by the handle 

• When bolted to a surface, an air or 

electric wrench may be used to break 

chain 

• Body bolt requires a 13⁄16" (21 mm) 

wrench and extractor pin uses a 9⁄16" 

(14 mm) wrench or socket 

5008135 Chain tool 

5008935 Replacement pin 

Progressive Suspension 

Gauge-Mounted Shock 

Absorber Pumps 

• Perfect OEM and aftermarket air shocks, 

forks, and emergency tire repair 

• Available in five styles making easy 

to service any low-pressure or highpressure 

pneumatic systems 

• An exclusive let-down valve allows for 

precise adjustments 

• Check valve insures a no-leak operation 

20135 0-30 lb. (2,1 bar) gauge (repl. 

OEM 34633) 

680124 0-60 PSI pump 

680125 0-100 PSI pump 

84182 0-300 lb.(21bar) gauge 

680124 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

Motion Pro Chain Breaker Tool 

A tough tool designed for shop use, also 

makes a perfect tool kit item. Properly 

used, the tool will break hundreds of 

chain links without failure. Pushes chain 

link pin completely through link. Handle 

folds to fit small tool pouch. Replaceable 

pin is heat treated and hardened for long 

life. For shop use, tool may be used with 

an air or electric impact wrench. 

Swingarm Bearing Installer/ 

Remover Tool 

894890 Fits Softail models 84-17 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

5008001 Fits all 420 to 630 chains 

5008002 Replacement pin 

TOOLS & 

EQUIPMENT 



Shock Adjusting Tool 

Fits Sportster models from 67-74, all 

Sportster and FXR models from 82-99, and 

all 4-speed FL and FX models from 58-86 

(exc. 84-86 FXST). 

20121 Replaces OEM 94700-52B 

Fork Cap Socket 

Specially-designed 1 3/8" hex socket is 

low-profile for use in the limited space 

under the handlebars when tightening 

fork caps. Requires a 1/2"-drive ratchet 

20902 For most models from 73-17 with 

1 3/8” caps 

JIMS Swingarm Bushing 

Assembly Tool 

Used to remove and replace swingarm 

cleveblocks, CC #38018 (OEM 47556-81). 

Cleveblocks are silicone-filled bushings 

that can be damaged if not installed 

properly. Tool applies pressure evenly 

to the bushings outer sleeve preventing 

damage. Can be used with or without a 

press. Includes lube. 

20952 For 82-94 FXR and Touring 

models from 80-01, as well as 

all aftermarket rubber mount 

frames 

Belt Tension Gauge 

• Compact design 

• Scale for easy reference 

• Designed to work with all belt drive 

models with a 10lb. specification 

5008350 MP Belt Tension GaugeC 

Motion Pro Steering Stem Tool 

Driver 

656208 For Most Harley-Davison 

Motorcycles 

400517 Replaces OEM 94455-89 



Shock Spring Compression 

Tool for Milwaukee Eight 

For easy disassembly of the shock 

absorber spring and installation of Kodlin 

M-8 Lowering Kits. 

Part#: 918355 , Fitment: 18-23 Softail 

, Unit: Each , Qty.: 1 

Shock Wrench for Softail 

Models 

Fits Softail models from 89-17. 

Shock Pressing Tool 

• For all M8 Softail shocks 

• For Evolution Softail in conjunction 

with the Müller Motorcycles Conversion 

Disc (sold separately) 

• Secure tensioning of the shock 

• Quick installation of the lowering kit 

• Made in Germany 

Part#: 917738 , Fitment: 18-23 Softail , 

Fitment Note: When using Conversion 

Kit 921856 also for EVO and TwinCam 

Softail Models , Unit: Each , Qty.: 1 

Conversion Disc for Shock- 

Pressing Tool 

With the Conversion Disc you can now 

easily clamp Evolution and Twin Cam 

lowerers into the Milwaukee Eight shock 

press. 

Part#: 921856 , Fitment: 84-17 Softail , 

Field of Application: For Müller Shock 

Lowering Kits , Description: Tool for 

Müller Shock Pressing Tool , Unit: 

Each , Qty.: 1 

JIMS Fork Seal Installers 

The perfect tool for installing fork seals, 

dust seals and chrome caps. Lightly grease 

to protect chrome on fork tubes. 

20450 Slide tool with Delrin plastic cap 

for 39mm forks 

20452 Slide tool only for 39mm forks 

20453 Slide tool only for 41mm forks 

640112 

Motion Pro Fork Compressor 

Kits 

Tired of wrestling with the installation of 

the fork cap because of the spring preload? 

Wrestle no more with these Fork 

Compressor Kits. 

• Designed to install fork caps on forks 

with a large amount of spring pre-load 

• Will work on most 39mm and 41mm 

H-D fork applications 

• Available in 39mm kit, 41mm kit or 

a combined kit for 39mm and 41mm 

together 

640111 41mm Compressor kit 

640112 39mm Compressor kit

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Adjustable Split Fork Seal 

Driver Set by K&L Supply 

Replace fork seals without removing the 

inner fork tube from the T-clamp. Set 

includes: one Split Seal Driver and three 

Seal Guides 35mm, 39mm, 41mm. 

400349 Fork Seal Installer. Use on 35mm, 

39mm, and 41mm fork tubes 

Jims Fork Seal Install Tool 

Tool to install fork seals on all models 

equipped with 49mm forks 02-23 

682594 Seal install tool 

JIMS Hollow Axle Plug Tool 

Late model Dyna and Sportsters are 

now using hollow axles. The use of this 

new hollow axle has eliminated the 

center point of the axle, which had been 

preferably used as a center point for rear 

tire alignment references. Lube the o-ring 

ends of these tools and insert in left and 

right ends of axle on Dyna, and Sportster 

models. This will give you the correct 

center point required for safe vehicle 

alignment. Sold each. 

622053 For all 08-17 Dyna and 08-20 

Sportster models 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

Shock Absorber Pre-Load 

Wrench by Progressive 

Suspension 

• Specially designed spanner wrench for 

use in adjusting shock absorbers on 

Softail models 

• Works left or right. Uses 3/8" socket 

drive 

• Specially designed to fit into tight 

spaces 

• Use to loosen and tighten lock nut and 

to adjust spring pre-load 

400310 89-17 Softail 

JIMS Fork Nut Socket 

Stop rounding off the flats of your top 

fork tube plugs with this specialty socket 

tool. 

20455 Fits all Wide Glide front forks 

from 48-17 

Wheel Alignment Tool 

• For use on Softails, Sportster 

and Dyna 

• Proper wheel alignment 

extends chain/sprocket and 

belt life 

• Designed to help set rear 

wheel alignment 

• Fast, accurate and easy to use 

• Fast, accurate and easy to use 

5008368 Wheel Alignment Tool 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

Fork Cap Fork Nut Socket 

• Use to remove or install top fork nut on 

glide forks 

• Has rubber protector on inside to 

prevent damage to chrome nut 


PART# 

FITMENT 

917613 84-17 Softail, except 16-17 

FXSE, 14-17 FXSB, 13-14 FXSBSE, 

80-85 FXWG, 93-03 FXDWG, 02 

FXDWGSE3, 04-05 FXDWGI 

917614 For all HD Models with a 35mm 

upper Fork Nut 

JIMS 25mm Wheel Bearing 

Puller Tool 

This tool is used to remove the new front 

25mm H.D. wheel bearings on most of the 

07-19 ABS or non-ABS wheels. 

Note: This tool must be used with the current JIMS wheel 

bearing installer/remover tool No.1042 (CC# 400394). 

640093 For use on 25mm bearing wheels 

640087 25 mm wheel bearing installer 

JIMS Late Sealed Wheel 

Bearing Race Removal and 

Installation Tool 

Use to remove and install "new style" 

sealed wheel bearings without damaging 

the wheel. 

400394 Fits 00-17 Twin Cam, 17-23 M8, 

00-20 Sportster, 00-10 Buell and 

15-20 Street models 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Radial Ball Bearing Remover 

by Motion Pro 

This set uses a split 3/4" collet design 

to remove radial ball bearings on H-D 

models. 

640135 Complete Set (includes 3/4", 1", 

& 25mm removers) 

CruzTOOLS TirePro Dial Tire 

Gauge 

Highly accurate and easy to read, 12" 

flexible hose allows easy valve access. 

Built-in valve holds reading until released, 

and ‘bleed-down’ to desired level. 

• Provides readings in PSI and Kpa scales 

• Includes protective rubber boot 

5861185 TirePro Dial Gauge 

JIMS 3rd Hand Axle Tool 

If you have noticed, as you are torquing 

down the axle nut after you set the 

proper belt tension (Deflection), the 

welded axle nut will move to the low side 

of adjuster cam. This movement will allow 

the belt to lose adjustment. Now with 

the “JIMS 3rd Hand Axle Tool”, you won’t 

need to find a helper to hold the nut or 

have to reach around the tire yourself 

to keep the nut from moving. Just place 

this tool over the welded nut on left side 

with the neck portion of tool resting over 

the swing arm. Hand screw the adjusting 

screw to take up any slack in tool. Torque 

the axle nut from the right side knowing 

that the welded nut will not turn allowing 

the belt to lose its adjustment. Sold each. 

622061 For all 02-23 FL models 

Tire Irons 

Designed for easily getting between tire 

bead and rim without pinching tubes. 

Card of 10. 

5008004 Tire Irons 

Motion Pro 16" Curved Tire 

Iron 

Black finish hardened alloy steel. Double 

compound curve makes removing the 

toughest tires a breeze. Also makes a 

great pry bar. 

5008007 Sold each, replaces OEM 94481-89T 



JIMS Rear Axle Nut Torque 

Adapter 

Assists in adjusting the drive belt tension 

or rear wheel alignment. Eliminates the 

need to remove the mufflers to perform 

this service. Designed with a 1/2" drive 

receiver hole for inserting a torque 

wrench allowing the axle nut to be 

torqued from an offset position 

622045 For 02-23 Touring and 05-17 

V-Rod models 

CruzTOOLS TirePro Digital Tire 

Gauge 

Compact ergonomic shape for easy 

pressure reading with large display, 

readings in 1/10 psi increments. 

• Readings available in multiple scales: 

PSI, Bar, Kpa, Kg-qcm 

• Auto power off, with recall of last 

reading 

5861184 TirePro Digital Gauge 

Three-In-One Truing Stand by 

K&L Supply 

Make the most of your workspace! This 

tool allows you to perform the following 

tasks all at one location, using one fixture. 

• Build and true laced wheels 

• Balance spoke and cast wheels 

• Check for runout (cranks, fork tubes) 

• Requires optional dial gauge (sold 

separately) 

400341 Three in one truing stand 

Accessories 

400342 Dial gauge for truing stand

APPAREL 

SEATS & 

TOURING 

K&L Supply MC305 Wheel 

Stand 

This portable wheel truing stand works 

on all motorcycle wheel sizes from 14" to 

21" wheels. A wheel can be mounted on 

adjustable centering cones or ball bearings 

(using axle) for truing and static balancing 

of wheels. Frame rails can be adjusted for 

wide rims/wheels. Lightweight, zinc-plated 

pressed steel frame. 

6128621 Truing/balancing stand 

14x16 mm Axle Hex Adapter 

for Indian 

This 14mm x 16mm axle adapter is 

designed to make it easy to remove the 

front wheel on an Indian Motorcycle. 

Works on Chief, Chieftan, Scout and 

Roadmaster models. Use adjustable 

wrench on one end with other end 

inserted to operate. Made of heattreated 

carbon steel. 


Rear Wheel Alignment Tool 

• A good wheel alignment extend belt, 

chain, pulley and sprocket life 

• This tool is simple, fast, and accurate to 

keep a correct alignment 

890571 Rear wheel alignment tool 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

K&L Supply Spoke Wheel 

Weight Hammer 

Special hammer for reaching behind the 

disc rotor when installing or removing 

spoke type wheel weights. 


‘Bike Foot’ Kick Stand 

Support 

Durable ABS pad protects tile, carpet and 

wood floor coverings from kick stand 

damage. Perfect for showrooms or your 

home garage. 

400410 ‘Bike Foot’ 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

K&L Supply Spoke Wheel 

Weight Removal Tool 

Designed to allow the tech to place the 

split tang of the tool between the rim 

and the weight and tap it off the nipple 

with a CC #640493 spoke wheel weight 

hammer. 


Engine Stand for Big Twins 

Great for repairing motors out of the 

bike or for building custom motors. May 

be bolted to a work bench for added 

stability. 

58530 Fits Big Twin models 36-99 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

K&L Supply Tire Tamer 

No more skinned knuckles! This Patent 

Pending revolutionary new tool holds the 

bead away from rim for easy valve stem, 

rim lock and tube installation. 


SHEETMETAL 

INSTRUMENTS 

& GAUGES 

K&L Supply Wheel Weight 

Scraper 

Easily removes most stick-on type wheel 

weights. 

640491 Pack of three 


Engine Stand for Big Twins by 

JIMS 

Perfect for engine repair. This benchmounted 

stand works with Big Twin 

engine cases from 36-99. 

20105 Engine stand 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


Engine Stand for Sportster 

Models by JIMS 

Top-quality steel stand for Sportster 

crankcases from 57-85 and Buell 87-02. 

Makes engine overhauls a breeze. 

20119 Engine stand 

JIMS Engine Stand for Twin 

Cam 88 Big Twins 

This steel, black powder-coated stand will 

simplify your engine repair. 

23302 Fits Twin Cam A engines from 

99-17 (except Softail engines) 

Engine and Transmission 

Rollers 

A wide selection of American-made rollers 

for the engine and transmission of most 

models from 30-86. Sold in resealable 

bags which are treated to prevent 

corrosion and are clearly marked with 

their size and OEM number. Bags of 100. 

Transmission Rollers for Sportster 

Models 

Fit the mainshaft on Sportster and K 

models from 52-E84 (23 used). 

PART # SIZE OEM # 

49062 +.0004 9096 

Transmission Rollers for Big Twin 

Models 

Fit 36-E77 OHV Big Twin mainshaft (44 

used), 36-E76 OHV Big Twin countershaft 

(44 used). 


49064 .125 x .615 Std. 9084 

Short Rod Rollers 

Fit 52 K models and OHV Big Twins from 

51-72 (36 used). 


49002 +.0004 9103A 

Short Rod Rollers (continued) 

Fit Sportster and KH models from 54-E86 

and Big Twins from 73-86 (34 used). 


49029 +.0008 9445A 

49031 +.002 9418 

49032 +.003 n/a 

49033 –.0002 9450A 

Long Rod Rollers 

Fit Big Twins from 73-86 (17 used). 


49019 +.0006 9182 

Crankcase Rollers for Big Twin Models 

Fit the left case of OHV Big Twins from 

30-57 (24 used), and the right case from 

58-86 (28 used). Also fit wheels with loose 

roller bearings. 


49052 +.0008 9224A 

Right Side Crankcase Rollers 

Fit 57-76 Sportster models and 55-57 OHV 

Big Twins (13 used). 


49043 +.0002 9422 

49045 +.0006 9424 

49047 +.001 9426 



Jims Rolling Buddy 

Rubber mounted H-D V-twins use the 

engine as a structural part of the chassis. 

When the engine is removed, it becomes 

impossible to roll the motorcycle. This can 

incapacitate a lift or, at the very least, tie 

up floor space. Our engine dummy plates 

are designed to take the place of the 

engine and literally bolt the chassis back 

together with the ability to get the bike 

rolled out of the way. 

642287 For Evo Touring, Dyna and FXR 

models 

642288 For 99-06 Touring & 99-05 Dyna 

models 

642289 For 07-16 Touring & 06-17 Dyna 

models 

Shock Bearing Puller 

• Safely removes and installs the upper spherical bearing on rear shocks 

• Fits 24mm OD bearings 

• Durable hardened tool steel construction 

• Corrosion resistant black oxide coating 

• Laser etched for easy identification 

• Reversible puller cup with cutaway fits a wide variety of shock reservoir and 

compression adjuster configurations 

• Durable brass thrust washer 

Part#: 916717 , Field of Application: For all Shocks with 24mm OD Bushings , 

Color: Black , Material: Steel , Unit: Each , Qty.: 1

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

Steel “Round Bungs” and “Round Nuts” by 

Hell’s Kitchen Choppers 

These Round Nuts are CNC machined for use as Sissy Bar 

mounts, Fender mounts, Gas Tank mounts and a hundred other 

applications. Paint, Chrome or Powder-coat as desired. Every 

person putting a bike, or a street rod together needs a selection 

of these handy puppies on their workbench! Use along with the 

“Round Bungs” for allen head bolts also available in this catalog. 

Sold in Pairs. 

632701 Round Bung: 1/2” long, 1/2” O.D., 1/4” I.D. For 1/4” 

socket allen head bolts 







632693 Round Nut 1/4-20 UNC x 1/2 

632694 Round Nut 1/4-20 UNC x 1 

632695 Round Nut 5/16-18 UNC x 1/2 

632696 Round Nut 5/16-18 UNC x 1 

632697 Round Nut 3/8-16 UNC x 1/2 

632698 Round Nut 3/8-16 UNC x 1 

Steel Iron Cross Plates by Hell’s Kitchen 

Choppers 

These cool Iron Crosses are water jet cut from 3/16” cold rolled 

steel. You can weld them on your sissy bar, use as brackets, make 

custom foot pegs or lots of other uses. Sold Raw. Paint, Chrome 

or Powder-coat as desired. Sold each. 

632690 Steel Iron Cross 1x1 

632691 Steel Iron Cross 2x2 

Chrome Sockethead Screw Plugs 

Individual Sizes 

32356 Chrome 17/32" hole plugs for spotlamp bar (pack of 10) 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

HKC stainless steel Iron Cross and Spades design washers 

Complete the style of your bike with matching design stainless steel washers from Hells Kitchen Choppers made in Germany. The 

versions for hex type screws are a little bit wider than the versions for socket screws. They are polished and available in several sizes. 

Spades design washers Iron Cross design washers 

682129 1/4" hex 

682130 1/4" socket 

682131 5/16" hex 

682132 5/16" socket 

682135 7/16" hex 

682136 7/16" socket 

682137 1/2" hex 

682138 1/2" socket 

682145 7/16" hex 

682146 7/16" socket 

682147 1/2" hex 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



913422 913423 913429 



Complete Engine Screw Kit 

Put an end to rotten and rusty bolts on your motorcycle. These bolt kits include all engine bolts + washers for the respective model. 

All included screws are made of stainless steel A2-70 and therefore rust and corrosion free. The screws are neatly packed in bags for 

the respective engine cover / assembly. The exchange is therefore very easy. One screw is replaced after the other. This means that no 

new gaskets are needed. 

Material: Stainless Steel , Unit: Kit , Qty.: 1 

FAMILY FITMENT DESCRIPTION GLOSS BLACK 

POWDER 

COATED 

SATIN BLACK 

POWDER 

COATED 

STAINLESS 

STEEL 

Buell XB 03-10 XB Screws for Buell XB Primary Cover, Inspection 

913449 913428 

Covers, Cam Cover 

Dyna, Softail 00-06 Softail, 99-05 Dyna Screws for Dyna, Softail Primary-, Cam-, 924779 913437 913416 

Inspection-, Derby-, Timer-, Tranny Side 

Cover, Rockerboxes, Lifterbase, Inner Primary 

Dyna, Softail 89-98 Softail, 91-98 Dyna Screws for Dyna, Softail Primary-, Cam-, 


Cover, Rockerboxes, Lifterbase 

924777 913435 913414 

FL Shovel 

FL Shovel 

Indian 

Bagger, 

Indian 

Cruiser, 

Indian 

Touring 

70-76 FL Shovel, 71-76 FX 

Shovel 

77-84 FL Shovel, 77-84 FX 

Shovel 

15-23 Indian Bagger, 12-23 

Indian Cruiser, 15-23 Indian 

Touring 

Screws for FL Shovel Primary Cover, 

Inspection Cover, Cam Cover, Piont Cover, 

Lifterbase 

Screws for FL Shovel Side Covers, Inner 

Primary, Header Mount, Point Cover, 

Lifterbase 

Screws for Indian Bagger, Cruiser, Touring 

Cam-, Inner Cam-, Sprocket-, Primary Cover, 

Starter, Horn 

Indian Scout 15-23 Indian Scout Screws for Indian Scout Primary-, Clutch-, 

Sprocket-, Thermostat-, Ignition Cover, 

Engine Cover leftside, Cover Stator Badge 

Pan America 21-23 Pan America, 21-23 

Sportster RH 

Softail 07-17 Softail, except 09 

FXSTSSE3, 08-11 FXCWC, 08 

FXCW, 13-14 FXSBSE, 14-17 

FXSB, 16-17 FXSE 

Softail 

13-14 FXSBSE, 14-17 FXSB, 

08 FXCW, 08-11 FXCWC, 09 

FXSTSSE3 

Softail 18-23 Softail, except 18-19, 

23 FXBR, 18-20 FXBRS 114, 

18 FXBRS 114 ANX, 18-20 

FLFB, 18-20 FLFBS 114, 18 

FLFBS 114 ANX, 18 FLFBS 

114 ANV, 19-20 FXDRS 114, 

21-22 FXBRS, 21-23 FLFBS, 

23 FLFBSANV 

Screws for Pan America Primary Cover, 

Manifold Cover, Camshaft Cover, Ignition 

Coil, Rockerbox, Sprocket Cover 

Screws for Softail Primary-, Cam-, Derby-, 

Timer-, Tranny Side Cover, Rockerboxes, 

Lifterbase 



Lifterbase 



Lifterbase 

924775 913429 913408 

924776 913430 913409 

924789 924774 

913444 913423 

913445 913424 

913438 913417 

924780 913439 913418 

924781 913440 913419 

Softail 99 Softail Evo Screws for Softail Primary-, Cam-, 

924778 913436 913415 


Cover, Inner Primary, Rockerboxes, Lifterbase 

Sportster 04-20 Sportster, except 08- 

10 XR1200, 10-13 XR1200X 

Screws for Sportster Primary-, Sprocket-, 

Cam-, Derby-, Timer-, Inspection Cover, 

Lifterbase, Rockerboxes 

Sportster 91-03 Sportster Screws for Sportster Primary-, Sprocket-, 

Cam-, Derby-, Timer-, Inspection Cover, Anti- 

Rotation-Plate, Lifterbase, Rockerboxes 

Touring 07-16 Touring Screws for Touring Primary-, Cam-, Derby-, 


Lifterbase 

924787 913442 913421 

924786 913441 913420 

924784 913433 913412

FAMILY FITMENT DESCRIPTION GLOSS BLACK 

POWDER 

COATED 

SATIN BLACK 

POWDER 

COATED 

STAINLESS 

STEEL 

Touring 17-23 Touring, 17-23 Trike Screws for Touring Primary-, Cam-, Derby-, 924785 913434 913413 


Lifterbase 

Touring 87-98 Touring Screws for Touring Primary-, Cam-, 

924782 913431 913410 


Cover, Rockerboxes, Lifterbase 

Touring 99-06 Touring Screws for Touring Primary-, Cam-, 


Cover, Rockerboxes, Lifterbase, Inner Primary 

924783 913432 913411 

Victory 

Motorcycles 

Victory 

Motorcycles 

Victory 

Motorcycles 

10, 12-16 Cross Country, 13- Screws are supplied for Primary Cover, Plate 

17 Cross Country Tour, 16- Primary, Sprocket Cover, Cam Cover 

17 Vision, 16-17 Magnum 

X-1, 15-17 Magnum, 15-17 

Gunner, 11-16 Hammer 8 

Ball, 13-17 Judge, 09, 11-12, 

16-17 Vegas, 17 Hammer S, 

09-11 Hammer 

17 Octane Screws are supplied for Primary Cover, 

Engine Cover left Side, Stator Batch, Ignition 

Cover, Thermostat Cover, Sprocket Cover 

02 V92C Touring Cruiser 

01-02 V92C Deluxe Cruiser 

00-03 V92C Standard 

Cruiser 00-01 V92C 

Sportcruiser 00 V92C 

Special Edition 

Screws are supplied for Primary Cover, Plate 

Primary, Sprocket Cover, Cam Cover 

V-Rod 02-17 V-Rod Screws for V Rod Clutch-, Alternator-, 

Sprocket-, Oil Pump-, Derby-, Cam-, Water 

Pump Cover, Oil Pump, Starter, Thermostat 

Assembly, Oil Filter Mount, Speed- 

,Crankshaft Sensor 

913446 913425 

913448 913427 

913447 913426 

924788 913443 913422 

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

914255 914257 914254 914256 

DRIVELINE 

Sprocket/Pulley Screw Kit 

Replace the original pulley screws with the high-quality screws from screws4bikes. Screws are available in black coated steel and 

titanium for some models. 

Thread: 7/16“-14 UNC , Unit: Kit , Qty.: 1 

FITMENT DESCRIPTION MATERIAL SCREW 

GRADE 

06-17 Dyna, 07-23 

Softail 

06-17 Dyna, 07-23 

Softail 

06-17 Dyna, 07-23 

Softail 

91-20 Sportster, 93-99 

Dyna, 93-99 Softail 

91-20 Sportster, 93-99 


91-20 Sportster, 93-99 


5 Allen Head Screws, 5 

Washers 

5 Conical Allen Head 

Screws, 5 Washers 

5 Hex Head Screws, 5 

Washers 

5 Allen Head Screws, 5 

Washers 

5 Conical Allen Head 

Screws, 5 Washers 

5 Hex Head Screws, 5 

Washers 

GLOSS BLACK 

POWDER COATED 

Steel/Steel 12.9 914257 924743 

SATIN BLACK 

POWDER COATED 

TITANIUM 

SATIN 

Titan/Titan Grade 5 924750 

Steel/Steel 8.8 914255 924742 

Steel/Steel 12.9 914256 924741 

Titan/Titan Grade 5 924749 

Steel/Steel 8.8 914254 924740 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



914241 914242 914243 914245 

914244 

Fender Strut Screw Kits 

High quality stainless steel screws available in stainless, gloss or satin black powdercoated. 

Material: Stainless Steel , Screw Grade: 700 N/mm2 , Unit: Kit , Qty.: 1 

FITMENT DESCRIPTION GLOSS BLACK 

POWDER COATED 

SATIN BLACK STAINLESS 

POWDER COATED STEEL 

04-20 Sportster Supplied are 4 screws and 4 washers 914241 924832 

07-17 Softail Supplied are 8 screws and 4 washers 924745 

07-23 Softail, except 19-20 FXDRS 114 Supplied are 4 screws and 4 washers 914245 924712 924819 

(strut to frame) 

08-12, 14-17 FLSTF, 08-11 FLSTSB, Supplied are 10 screws and 4 washers 914243 

08-09 FXSTB, 08 FXSTC, 10-12, 14-17 

FLSTFB, 11-15 FXST, 13 FLSTF 103, 13 

FLSTFB 103, 16-17 FLSTFBS 

12, 14-17 FLS, 11-12 FXS, 13 FLS 103, Supplied are 8 screws and 4 washers 914242 924855 

13 FXS 103, 16-17 FLSS 

18-23 Softail, except 19-20 FXDRS 114, Supplied are 8 screws and 8 washers 914244 924713 924820 

18-20 FLDE, 18-23 FLSB 

22-23 Nightster RH975, 23 Nightster 

Special RH975S 

Supplied are 4 screws 924739 924853 

914267 914265 

924835 914267 

Gas Tank Mounting Screw Kits 

The tank mounting kit consists of 2 black nuts, 2 black washers and a threaded rod. All 

parts are made of stainless steel and are „Coated in Germany“. No chipping of the paint! 


FITMENT DESCRIPTION GLOSS BLACK POWDER COATED STAINLESS STEEL 

00-17 Softail Supplied are 1 threaded rod, 2 cap nuts and 2 washers 914266 

04-20 Sportster Supplied are 1 threaded rod, 2 cap nuts and 2 washers 914264 924835 

04-20 Sportster Supplied are 2 threaded rod, 4 cap nuts and 4 washers 914265 

18-23 Softail Supplied are 1 threaded rod, 2 cap nuts and 2 washers 914267 924815 



APPAREL 

SEATS & 

TOURING 

914232 914248 914247 914246 

FOOT 

CONTROLS 

Front Fender Screw Kits 

Replace the original screws of your front fender with the high-quality screws4bikes stainless steel screws. 


FAMILY FITMENT GLOSS BLACK SATIN BLACK STAINLESS 

POWDER COATED POWDER COATED STEEL 

Dyna, Softail 91-17 Dyna, except 12, 14-16 FLD, 13 FLD103, 21-23 FXBBS, 20- 924717 924824 

23 FXST, 18-20 FXBB, 18-20 FXLR 

Softail 18, 20 FXFBS 114, 18-20 FXFB, 21-23 FXFBS, 19 FXFB 114 924720 924828 

Softail 18-20 FLDE, 18 FLFBS 114 ANV, 18 FLFBS 114 ANX, 18-20 FLFBS 

924826 

114, 18-20 FLFB, 18 FLHCS 114 ANV, 18 FLHCS 114, 18-21 FLHC, 

18-21 FLSL, 19-20 FLHC 114, 21-23 FLFBS, 21-23 FLHCS, 23 

FLFBSANV, 23 FLHCSANV 

Softail 18 FXBRS 114 ANX, 18-20 FXBRS 114, 18-19, 23 FXBR, 21-22 924718 924825 

FXBRS 

Softail 20-23 FXLRS, 22-23 FXLRST, 22 FXRST 924719 924827 

Softail 91-17 Softail, except 89-03 FXSTS, 01-02, 04-06 FXSTSI, 05-06 914246 

FLSTSCI, 01-06 FXSTDI, 07 FXSTSSE, 07 FLSTSC, 00-03, 05, 07 

FXSTD, 08 FXSTSSE2, 08-11 FLSTSB, 08 FXCW, 08-11 FXCWC, 09 

FXSTSSE3, 95-97 FXSTSB, 97-03 FLSTS, 01-03 FLSTSI, 12 FLSTSE3, 

10 FLSTSE, 11 FLSTSE2, 13-14 FXSBSE, 14-17 FXSB, 16-17 FXSE 

Sportster 04-20 Sportster, except 08-10 XR1200, 10-20 XL1200X, 10-13 914248 

XR1200X, 16-20 XL1200CX, 18 XL1200X ANX, 19-20 XL1200XS 

Sportster 10-20 XL1200X, 18 XL1200X ANX, 19-20 XL1200XS 914247 

Sportster 16-20 XL1200CX 924727 924839 

Sportster 18 XL1200X ANX, 10-20 XL1200X, 19-20 XL1200XS 924838 

Sportster RH 21-23 Sportster S RH1250S 924733 924847 

Sportster RH 22-23 Nightster RH975, 23 Nightster Special RH975S 924734 924848 

V-Rod 02-17 V-Rod 914232 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

914237 914238 

Footrest Screw Kits 

True to the motto „Black is Beautiful“, this set consists of 6 stainless steel screws with a high quality black gloss powder-coated head. The 4 

larger screws replace the original silver screws on the rear footpegs, the 2 small stainless steel screws replace the screws on the front footpegs. 

Color: Gloss Black Powder Coated , Material: Stainless Steel , Screw Grade: 700 N/mm2 , Unit: Kit , Qty.: 1 

FAMILY FITMENT POSITION GLOSS BLACK POWDER COATED 

Softail 18-23 Softail Front 924705 

Sportster 04-20 Sportster Front 924726 

V-Rod 02-06 V-Rod Front, Rear 914237 

V-Rod 07-17 V-Rod Front, Rear 914238 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



914263 914262 

Derby Cover Screw Kits 

High quality stainless steel derby cover screws available in stainless, gloss or satin black powdercoated. 


FITMENT 

GLOSS BLACK POWDER COATED MATTE BLACK POWDER COATED STAINLESS STEEL 

04-20 Sportster 924728 914263 924841 

19-23 Softail 924722 924830 

99-17 Dyna, 00-18 Softail, 99-23 Touring, 

09-23 Trike 

924744 914262 

Primary Cover Screw Kit 


FAMILY FITMENT SATIN BLACK STAINLESS 


Dyna, Softail 91-98 Dyna, 89-99 Softail 924752 924859 

Dyna, Softail 99-05 Dyna, 00-06 Softail 924753 924860 

Dyna, Softail, Touring 06-17 Dyna, 07-17 Softail, except 13-14 FXSBSE, 14-17 FXSB, 16-17 FXSE, 08 924754 924861 

FXCW, 08-11 FXCWC, 17-23 Touring, 17-23 Trike 

FL Shovel, FX Shovel 70-84 FL Shovel, 71-84 FX Shovel 924751 924858 

Pan America 21-23 Pan America, 21-23 Sportster RH 924761 924868 

Softail 13-14 FXSBSE, 14-17 FXSB, 16-17 FXSE, 08 FXCW, 08-11 FXCWC 924760 924867 

Sportster 04-20 Sportster 924756 924863 


Touring 07-16 Touring 924759 924866 





APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Cam Cover Screw Kit 

Replace the original screws of your cam cover with the high-quality screws4bikes stainless steel screws. 


FAMILY FITMENT SATIN BLACK POWDER COATED STAINLESS STEEL 

Dyna, Softail, Touring 91-98 Dyna, 89-99 Softail, 89-99 924763 924870 

Touring 

Dyna, Softail, Touring, Trike 99-17 Dyna, 00-17 Softail, 00-16 924764 924871 

Touring, 09-16 Trike 

FL Shovel, FX Shovel 70-84 FL Shovel, 71-84 FX Shovel 924762 924869 

Softail, Touring, Trike 18-23 Softail, 17-23 Touring, 17-23 924767 924874 

Trike 



HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

Point Cover Screw Kit 

Replace the original screws of your point cover with the high-quality screws4bikes stainless steel screws. 


FITMENT DESCRIPTION SATIN BLACK POWDER COATED STAINLESS STEEL 

00-17 Softail, 00-16 Touring Supplied are 5 screws 924771 924878 

18-23 Softail, 17-23 Touring, 17-23 Supplied are 2 screws 924772 924879 

Trike 

70-84 FL Shovel, 71-84 FX Shovel, 

85-94 FX Model, 91-99 Dyna, 84-99 

Softail, 85-99 Touring, 91-20 Sportster 


GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



924724 924834 924715 924822 

924714 924821 924716 924823 

Aircleaner Screw Kit 

Replace the original screws of your air cleaner cover with the high-quality screws4bikes stainless steel screws. 


FITMENT DESCRIPTION SATIN BLACK STAINLESS 


04-20 Sportster Supplied are 2 screws 924724 924834 

18-20 FLDE, 18-21 FLHC, 18-21 FLSL, 18-20 FXLR, 20-23 FXST Supplied are 1 screw and 1 washer 924714 924821 

18-20 FLFB, 18-23 FLSB, 18-20 FXBB, 18-20 FXFB Supplied are 5 screws 924716 924823 

18 FXBRS 114 ANX, 18-20 FXBRS 114, 18 FLFBS 114 ANV, 18 

FLFBS 114 ANX, 18-20 FLFBS 114, 18 FLHCS 114 ANV, 18 FLHCS 

114, 18, 20 FXFBS 114, 21-22 FXBRS, 21-23 FLFBS, 21-23 FLHCS, 

21-23 FXBBS, 21-23 FXFBS, 23 FLFBSANV, 23 FLHCSANV 


Gas Cap Screw Kit 

Fitment: 21-23 Sportster S RH1250S , Material: Stainless 

Steel , Unit: Kit , Qty.: 1 

PART# 

COLOR 

924729 Gloss Black Powder Coated 

924842 Stainless Steel 

Headlamp-/Fork Cover Screw Kit 

• Supplied are 4 screws 

Fitment: 18-20 FLFB, 18-20 FLFBS 114, 18 FLFBS 114 ANV, 

18 FLFBS 114 ANX, 21-23 FLFBS, 23 FLFBSANV , Material: 

Stainless Steel , Unit: Kit , Qty.: 1 

PART# 

COLOR 





APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Lifterbase Screw Kit 

Fitment: 04-20 Sportster , Material: Stainless Steel , Unit: 

Kit , Qty.: 1 

PART# 

COLOR 

924769 Satin Black Powder Coated 


Battery Side Cover Screw Kit 

Fitment: 18-23 Softail , Material: Stainless Steel , Unit: Kit 

, Qty.: 1 

PART# 

COLOR 




HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

924736 924850 924737 924851 

ENGINE 

Chin Fairing Screw Kit 


FITMENT SATIN BLACK POWDER COATED STAINLESS STEEL 

21-23 Sportster S RH1250S 924736 924850 

22-23 Nightster RH975, 23 Nightster Special RH975S 924737 924851 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

924723 924831 924704 924812 924731 924845 

FRAMES 

Belt Cover Screw Kit 


FITMENT SATIN BLACK POWDER COATED STAINLESS STEEL 

04-20 Sportster 924723 924831 

18-23 Softail 924704 924812 

21-23 Sportster RH 924731 924845 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Transmission Top Cover Screw Kit 

Fitment: 07-16 Touring, 07-17 Softail, 06-17 Dyna , 


PART# 

COLOR 



Mirror Nuts Kit 

Fitment: 82-20 Sportster, 91-17 Dyna, 84-23 Softail, 85-23 

Touring, 09-23 Trike, 02-17 V-Rod , Fitment Note: Except 

VRSCF , Material: Stainless Steel , Unit: Kit , Qty.: 1 

PART# 

COLOR 



Triple Tree Screw Kit 


, Qty.: 1 

PART# 

COLOR 



Mirror Clamp Screw Kit 

Fitment: 21-23 Sportster RH , Material: Stainless Steel , 

Unit: Kit , Qty.: 1 

PART# 

COLOR 





APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Axle Clamp Screw Kit 



PART# 

COLOR 



Handlebar Clamp Screw Kit 

Part#: 924735 , Fitment: 21-23 Sportster RH , Color: Satin 

Black Powder Coated , Material: Stainless Steel , Unit: Kit 

, Qty.: 1 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

Heatshield Screw Kit 

Part#: 924843 , Fitment: 21-23 Sportster S RH1250S , Color: 

Stainless Steel , Material: Stainless Steel , Unit: Kit , Qty.: 1 

EXHAUST 

INTAKE 

ENGINE 

Fork Clamp Screw Kit 



PART# 

COLOR 



Titan Front Brake Caliper Screw Kit 

• Rolled thread 

• Material: Titanium 6AL-4V Grade 5 

• Tensile strength: 950 - 1050 N/mm² 

• PVD coated 

Color: Black , Description: 2-Piece , Material: Titan , Unit: 

Kit , Qty.: 1 

PART# FITMENT OEM # 

924748 00-03 Sportster, 00-17 Dyna, 00-14 

Softail, 00-07 Touring, 02-05 V-Rod 

924747 04-20 Sportster, 15-23 Softail, 08-23 

Touring, 09-23 Trike, 06-17 V-Rod 

44160-00, 

44163-00 

44160-00 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

Electronic Control Modul (ECM) Screw Kit 


, Qty.: 1 

PART# 

COLOR 



SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



924836 914251 924837 

914253 

Sockethead Fork Clamp Screw Kit 

Screw Grade: 12.9 , Unit: Kit , Qty.: 1 

FITMENT 

04-20 Sportster, except 16-20 XL1200X, 16-20 XL1200CX, 18 

XL1200X ANX, 19-20 XL1200XS 

16-20 XL1200X, 16-20 XL1200CX, 18 XL1200X ANX, 19-20 

XL1200XS 

DESCRIPTION GLOSS BLACK POWDER COATED STAINLESS STEEL 

4-Piece 914251 924836 

6-Piece 914253 924837 

Standard Male Mount Foot Peg Screw Kit 

Part#: 924857 , Field of Application: For HD Male Mount Footpegs , Color: Stainless Steel , Material: Stainless Steel , 


Headlight Screw Kit 

• Supplied are 2 screws 

924710 924817 924711 

924818 


FAMILY FITMENT GLOSS BLACK POWDER COATED STAINLESS STEEL 

Softail 18, 20 FXFBS 114, 18-20 FXFB, 21-23 FXFBS, 19 FXFB 114 924710 924817 

Softail 18 FXBRS 114 ANX, 18-20 FXBRS 114, 18-19, 23 FXBR, 21-22 FXBRS 924711 924818 



914236 

924725 

Shock Screw Kits 

True to the motto „Black is Beautiful“, this set consists of 4 galvanized screws with a high quality black gloss powder-coated head. 

Also included in the kit are two matching washers, which were also powdered black. Screws replace the original silver screws on the 

shock absorbers. 

Color: Gloss Black Powder Coated , Material: Steel , Screw Grade: 10.9 , Unit: Kit , Qty.: 1 

PART# 

FITMENT 

914236 07-17 V-Rod, except 07 VRSCR 

924725 04-20 Sportster

APPAREL 

Headlight Screw Kits 

PART# FITMENT COLOR FINISH 

914233 04-17 V-Rod, 02, 03 VRSCA Gloss Black Powder Coated 

Shifter Rod Screw Kits 


914235 04-17 V-Rod, 02, 03 VRSCA Gloss Black Powder Coated 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

914229 

914230 

914231 

Engine Mount Screw Kits 


914234 

04-17 V-Rod, 02, 03 

VRSCA 

Gloss Black Powder Coated 

LIGHTING 

ELECTRICAL 

EXHAUST 

Brake Caliper Screw Kit for V-Rod 

Fitment: 07-17 V-Rod 

PART# DESCRIPTION COLOR FINISH 

914229 For front and rear 

914230 For front 

914231 For rear 

Gloss Black Powder 

Coated 

INTAKE 

ENGINE 

GASKETS 

914227 914253 

Frame Screw Kits 


914228 

04-17 V-Rod, 02, 

03 VRSCA 


TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

914249 914251 914252 

924833 

914259 

FRAMES 

Front Fork Brackets Screw Kits 

PART# FITMENT COLOR 

914227 04-17 V-Rod, 02, 03 VRSCA 

914249 13, 14 FXSBSE, 14-17 FXSB 

914250 18-19, 23 FXBR, 18-20 FXBRS 114, 18 FXBRS 

114 ANX, 21-22 FXBRS 

914251 04-20 Sportster, except 16-20 XL1200X/XS, 

XL1200CX 

914252 04-20 Sportster, except 16-20 XL1200X/XS, 

XL1200CX 

914253 16-20 XL1200X, 18 XL1200X ANX, 19-20 

XL1200XS 

FINISH 

Gloss 

Black 

Powder 

Coated 

Handlebar Controls Clamping Screw Kit 

Handlebar control clamping screws to replace the OEM versions. 

Material: Stainless Steel , Unit: Kit , Qty.: 1 , Screw Grade: 

700 N/mm2 

PART# FITMENT COLOR 

924833 04-20 Sportster Stainless Steel 

914259 04-20 Sportster Gloss Black Powder Coated 

914258 96-03 Sportster, 96-17 

Dyna, 96-17 Softail, 96-16 

Touring 


FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Master Cylinder Cover Screw Kits 

Part#: 914260 , Fitment: 96-03 Sportster, 96-17 Dyna, 96-17 

Softail, 96-16 Touring , Color: Gloss Black Powder Coated 

, Description: Master Cylinder Cover , Material: Stainless 

Steel , Unit: Kit , Qty.: 1 , Screw Grade: 700 N/mm2 

Front Fender Mounting Screws 

• Black Screw Sets by Cult Werk 

• Several sets to complete the ‘All Black‘ look. 

Color: Black, Galvanized , Material: Steel , Unit: Set , Qty.: 1 

PART# 

FITMENT 

618469 02-11 V-Rod 

618474 12-17 V-Rod 

901686 10-20 XL1200X, 18 XL1200X ANX, 19-20 XL1200XS 

Well Nuts 

• Well nuts are used for various mounting applications 

• For example, tightening your windshield or mounting your oil 

tank 

Color: Black , Material: Rubber , Unit: Pack , Qty.: 10 

PART# OEM # 

919717 5027 




914239 

Exhaust Screw Kits 

921420 


914239 09-17 VRSCF, 13 VRSCF105 

914240 

07-17 VRSCDX, 08 

VRSCDXA, 12 VRSCDX_ 

ANV, 13 VRSCDX105 


Coated 


Coated 

688642 

688641 

19 700 N/mm2 


Complete Handlebar Hand Controls Screw Kit 

Kit contains screws for brake- and clutch control clamps, switch 

housings and master cylinder cover screws. 

Part#: 914261 , Fitment: 96-03 Sportster, 96-17 Dyna, 96-17 

Softail, 96-16 Touring , Color: Gloss Black Powder Coated , 

Material: Stainless Steel , Unit: Kit , Qty.: 1 , Screw Grade: 

Well Nuts 

Well nuts for various applications from headlight to cover 

mounting, windshield mounting, ignition module mounting and 

many others. Pack of ten. 

688641 Well nuts 6-32 threads, (repl. OEM# 5210) 

688642 Well nuts 10-32 threads, (repl. OEM# 5207)

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

696795 

696796 

696794 

Slim Tophat Blind Threaded 

Steel Bung 

These tophat-shaped, blind threaded steel 

bungs are perfect for making gas tank 

and oil tank mounts 

HAND 

CONTROLS 

607623 5/16”-18 (4-pack) 

LIGHTING 

ELECTRICAL 

696793 

696792 

EXHAUST 

INTAKE 

Extended Belt Sprocket Mounting Kit by Gardner 

696795 Gardner belt sprocket mounting kit for Softail models 07-23 2 1/2” long, smooth 

heads 

696796 Gardner belt sprocket mounting kit for Softail models 07-23 2 1/2” long, knurled 

heads 

Extended Belt Sprocket Mounting Kit for Custom Applications 

696792 Sockethead 7/16” x 2 1/2” without washers 

696793 Smooth allen head 7/16” x 2 1/2” without washers 

696794 Hex head 7/16” x 2 1/2” without washers 

Show Bike Kits for Twin Cam 88 

Models by Colony 

Give your bike the ultimate in bolt-on 

beauty. Chrome-plated sockethead kits for 

motor and transmission. 

Complete Kits 

36949 For all 99-05 Dyna Glide models 

36980 For all 99-05 FLT, FLHT and Road 

King models 

Individual Kits for 99-05 Dyna Glide and 

99-06 Touring Models 

36982 For cam cover 

36983 For lifter blocks 

36988 For point cover 

36990 For primary cover on Touring models 

36991 For rocker boxes 

Other Colony Dress-Up Kits 

35927 Complete upper and lower motor mount kit for Softail models from 84-99 

95195 Motor mount bolts for Evolution style engines in aftermarket frames feature a 

3 1/2" upper and 2 3/4" lower 

72073 Button head fork drain screw kit with brass washers (repl. OEM‘s #45790-80, 

#45996-73) 

Zinc-Plated Kits 

72058 Motor mount kit. Fits Softail models from 84-99 

72062 Lower motor mount kit. Fits 5-speed Touring and FXR models from 80-99 

72064 Transmission mount kit. Fits 5-speed Softail models from 86-99 


Gardner-Westcott Company 

has been serving the motorcycle 

industry for over 3 decades. A name 

built on Quality, Precision, Dedication 

and our total Commitment to the 

Customer. Gardner-Westcott produces 

the highest quality Chrome Plated 

fasteners the industry, and carry a full 

line of Motor Sets, Side Cover Sets, 

Individual Application Sets, and Fastener 

Assortments. They have the largest 

selection of fasteners for whatever you 

want to build for every motor and in 

every style and that is why Gardner- 

Westcott is “The First Name in Exceptional 

Quality Show Chrome Fasteners.” 

Disc Brake Caliper Mount 

690629 00-07 Front Brake Caliper (except 

Springers) 

690631 06-07 Rear Brake Caliper for 

Softail FX Models 

690630 00-07 Rear Brake Caliper (except 

06-07 Softail FX models and 06 

Dyna Glides) 

Disc Brake Rotor to Hub 

690633 For front brake disc with 56mm 

centering diameter, cast wheels 

and 97 up laced wheels, 84-20 

Sportster, 85-94 FX Model, 

91-17 Dyna, 84-23 Softail, 85-23 

Touring, 09-23 Trike, 84 FLT, 84 

FLTC, dual discs need two sets 

690632 For models with cast wheels 

92-94 FX Model, 92-17 Dyna, 

92-23 Softail, 93-23 Touring, 

92-20 Sportster, for models with 

laced wheels 97 up 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


Dome Lifter Block Bolt Covers 

Don‘t ignore the lifter blocks when going for the custom look. 

Set of eight covers install in seconds with included silicon 

adhesive. 

66004 Fits Big Twins from late 76-99 

Chrome Bolt Covers 

Finish the look of plain exposed knurled sockethead bolts with 

these chrome-plated plastic covers. 

Smooth Covers 

PART # SIZE PACKED 

66001 1/4" 20 

66002 1/4" 50 

66003 1/4" 100 

66012 3/8" 20 

66005 5/16" 20 

Skull Covers 

PART # SIZE PACKED 

66027 1/4" 20 

66031 5/16" 50 

66037 3/8" 50 

STAINLESS STEEL BY PRO-BOLT 

KITS FOR DYNA MODELS 

684555 Engine kit 99-05 Dyna models hex 

KITS FOR SPORTSTER MODELS 

684905 04-20 Sportster, except 08-10 XR1200, 10-13 XR1200X 

WORKSHOP KITS 

684924 200 peaces Workshop Boxed kit UNC hex+spike 

684925 Workshop Cabinet 500 Pcs Imperial assorted 



APPAREL 

SEATS & 

TOURING 

Chrome Timing Plug 

Sockethead style for all Shovel & EVO models from 70-99. (rep. 

OEM 720) 

35623 Replaces OEM 720 

FOOT 

CONTROLS 

HAND 

CONTROLS 

LIGHTING 

Custom Chrome Engine and Cover Sets 

These kits contain show-quality chrome-plated components in kits 

designed for specific applications by year and model. Most kits are 

available in chrome-plated knurled sockethead hardware, or with 

the head polished smooth before plating. Some kits may contain 

hex or buttonhead hardware where sockethead hardware is not 

appropriate. These kits add visual appeal with functional topquality, 

American-made fasteners. 

Complete Motor Kits for Sportster models 

612348 04-20, except 08-13 XR1200/X7 - knurled 

612349 04-20, except 08-13 XR1200/X– smooth 

Side Cover Bolt Kits for Sportster models 

612301 Fits Sportster models from 91-03 – knurled 

Derby Cover Bolt Kit for Sportster models 

612335 Fits Sportster models from 04-20 

Rocker Box Sockethead Screw Set for Sportster models 

36378 Fits Sportster models from 91-03 - knurled 

36377 Fits Sportster models from 91-03 – smooth 

612344 04-20, except 08-13 XR1200/X – smooth 

Motor Mount Sockethead Screw Set for Sportster models 

(front upper and lower and top center mounts) 

36372 Fits Sportster models from 91-03 – smooth 

612341 04-20, except 08-13 XR1200/X - knurled 

Motor Mounts for Sportster models 

612303 Lower motor mount bolts for Sportster models from 

91-03 -knurled 

Miscellaneous Kits for Sportster Models 

Fits Sportster models from 91-03 Rocker box sockethead screw set 

36378 Smooth 

36377 Knurled 

Fits Sportster models from 91-03. Motor mount sockethead screw 

set; front upper and lower and top center mounts 

36372 Smooth 

Miscellaneous Kits for Big Twin Models 

Fits 89-93 Motor mount set. Sockethead Dyna Glide models and 

hex head screws for top and bottom motor mounts 

36384 Smooth 

36383 Knurled 

Fits 89-93 Softail Primary cover set. Sockethead and Dyna Glide 

model screws for derby, inspection, inner and outer primary 

36382 Smooth 

36381 Knurled 

Fits 36-64 Primary cover set. Sockethead Big Twins screws 

25079 Knurled 

Fits 36-64 Derby and chain inspection Big Twins cover set 

25095 Flat head screws 

Fits Late 76-99 Lifter base set. Sockethead screws Big Twins 

36366 Smooth 


Colony Chrome Show Bike Kits 

Acorn-style kits with all the necessary hardware to transform a 

stock engine into a classic. 

36173 Fits Sportster models from 77-85 

36174 Fits Panheads from 58-65 

36261 Fits Shovelheads from 70-75 

Chrome Acorn Nuts 

Sold on skin-packed display card. Available in fine, coarse or 

metric threads. 

PART # SIZE PACK 14413 7/16"-14 2 

14427 10-24 5 

14401 1/4"-20 5 

14403 1/4"-28 5 

14405 5/16"-18 4 

14407 5/16"-24 4 

14409 3/8"-16 3 

14411 3/8"-24 3 

14415 7/16"-20 2 

14417 1/2"-13 1 

14419 1/2"-20 1 

14421 6mm 5 

14423 8mm 4 

14425 10mm 3 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 


Chrome Brake Rotor, Drum and 

Sprocket Hardware 

Chrome-plated bolts and where required, nylon 

insert backing nuts. The finest American-made 

quality by Colony. 

A 

B 

C 

D 

E 

F 

G 

N 

O 

P 

Q 

H 

K 

L 

I 

J 

M 

BRAKE ROTOR KITS 

STYLE PART # DESCRIPTION 

A 36233 Front or rear rotor to hub for 82-85 FLT models (repl. OEM 

1642) 7/16"-14 x 1.75" countersunk 

B 36230 Rear rotor to hub screw and nut kit for 79-91 Sportster and 

FX models, and 81-84 FL models with spoke or cast wheels 

(repl. OEMs 31605 and 31604) 3/8“-16 x 1.5“ countersunk (set 

of 5) 

C 36232 Front or rear rotor to hub screws for 80-81 FLT models (repl. 

OEM 1643) 7/16"-14 x 1.25" countersunk 

D 36225 Front rotor to hub screw and nut kit for 78-83 FXWG models 

(dual disc requires 2 sets) 5/16"-18 x 1" countersunk 

E 25193 Replacement countersunk bolt (pack of 10) 

F 36228 Front rotor to hub screws for single disc FX and Sportster 

models from 74-77. 1/4“-20 x 5/8“ countersunk (set of 5) 

G 35657 Rotor to hub screws for FX models 74-80, and Sportster models 

from 74-77. 5/16"-18 x 1.25" countersunk 

H 36226 Front or rear rotor to hub thin hex head bolt and nut kit for 

rear of FL models 73-80, front on FL models 73-74 and front 

on FX and XL models 73 (Repl. OEM# 41198-73) 3/8“ -16 x 1“ 

thin hex. (set of 5) 

I 36227 Same as CC #36226 but with buttonhead screws instead of 

hex (set of 5) 

J 35660 Rear cast wheel rotor to hub for FX and FL models 79-91 and 

XL models 79-96. 3/8"-16 x 1" buttonhead 

K 36231 Front rotor to hub screw and nut kit for Softail and FXWG 

models 84-17. 5/16“-18 x 7/8“ buttonhead (set of 5) 

L 36229 Front brake disc with 56mm centering diameter, cast wheels 

and 97 up laced wheels, 84-20 Sportster, 85-94 FX Model, 

91-17 Dyna, 84-23 Softail, 85-23 Touring, 09-23 Trike, 84 FLT, 

84 FLTC, dual discs need two sets. 5/16”-18x7/8” 

REAR BRAKE DRUM KIT 

M 36324 Rear brake drum bolt and nut kit special shouldered bolts 

and locknut for 52-78 XL models with rear drum. 5/16"-24 

special hex 

SPROCKET AND PULLEY KITS 

N 36114 Sockethead bolt and nut kit for FXWG and FXRS models from 

85-92 with belt drive and spoke rear wheel (repl. OEM 4726) 

O 36113 Sockethead bolt and nut kit for FL, FX, and XL models with 

chain drive spoke rear wheel from 73-92 (repl. OEM 41197-73) 

P 36112 Sockethead bolt and washer kit for FL and FX models from 

73-98 and Sportster models 73-90 with cast rear wheel and 

belt drive (repl. OEM 3769) 

Q 35659 Bolt, nut and washer kit with special domed hex bolts for FX, 

FL and XL models from 73-03 with spoke rear wheels 

Q 35658 Bolt and washer kit with special domed hex bolts for FX and 

FL models from 73-98 with cast rear wheels 

— 72059 Custom hardware kit with flat sockethead screws, countersunk 

washers and locknuts. Fits FL, FX and Sportster models 

with chain drive and spoked wheels from 73-92 

— 72060 Custom hardware kit with flat sockethead screws and countersunk 

washers. Fits FL, FX and Sportster models with belt or 

chain drive and cast wheels from 73-98 

— 72061 Custom hardware kit with flat sockethead screws, countersunk 

washers and locknuts. Fits FXWG and FXRS models with 

belt drive and spoked wheels from 85-99 



Chrome Rear Fender Strut Mounting Kits by 

Colony 

Kits include everything necessary for mounting fender struts. 

35165 For mounting four hole struts on Fat Boy and Heritage 

Softail models from 86-99 (repl. OEM 59969-86) 

35164 For mounting six hole struts on Springer, Custom and 

Bad Boy models from 86-99 (repl. OEM59954-86) 

Complete Rocker Box Hardware Kit 

Full 32 piece rocker box mounting kit contains everything 

needed to install two rocker boxes. Fits all Evolution Big Twin 

and Sportster lower rocker boxes. 

94053 Complete Evo rocker box hardware kit.

APPAREL 

Custom Chrome Engine and Cover Sets 

Chrome-plated components in kits for specific applications by year and 

model. Most kits are available in chrome-plated knurled sockethead 

hardware, or with the head polished smooth before plating. Some kits 

may contain hex or buttonhead hardware where sockethead hardware 

is not appropriate. 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

COMPLETE MOTOR KITS FOR SPORTSTER MODELS 

APPLICATION 

91-03 XL models 

86-90 XL Evolution models 

77-E84 XL models 


57-69 XLCH 

DESCRIPTION 

SIDE COVER KITS FOR SPORTSTER MODELS 

Upper and lower front and top center motor mounts, rocker box, 

primary, inspection, crankcase, shifter, cam, sprocket cover, rear 

master cylinder mount, right side crankcase, timing hole plug and 

point cover 

Cam, primary, rocker box, lifter base, top motor mount, oil filter 

mount and point cover 

Cam, primary, rocker box, lifter base, top motor mount, point/ 

magneto cover and generator mount 

Cam, primary, rocker box, lifter base, top motor mount, generator 

mount, sprocket cover and point cover 

Cam, primary, lifter base, magneto cover, generator, sprocket cover, 

rocker box and top motor mount 

36380 Smooth 36379 Knurled 


25088 Knurled 


25086 Knurled 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

APPLICATION 


DESCRIPTION 

Right side; cam cover, crankcase, sprocket cover and rear master 

cylinder mount 

36374 Smooth 

91-03 XL models Left side; crankcase and inspection covers and shifter bolt 36376 Smooth 36375 Knurled 

86-92 XL models Cam, primary and oil fill check screw 36368 Smooth 

ENGINE 

GASKETS 

77-85 XL models Cam, primary, sprocket cover and oil fill check screw 25094 Knurled 

71-76 Sportster models Cam, primary and oil fill check screw 25093 Knurled 

COMPLETE MOTOR KITS FOR BIG TWIN MODELS 

TRANNY & 

CLUTCH 

APPLICATION 

DESCRIPTION 

87-93 Big Twins (except 

Softail and Dyna Glide 

models) 

Cam, primary, rocker box, lifter base, inner primary, timing plug, 

motor mounts and point cover 


DRIVELINE 

89-98 Softail and Dyna 

Glide models 

87-88 Softail models 

Cam, inner and outer primary covers, point cover, timing plug, 

rocker box, lifter base, top motor mount, 

Cam, primary, rocker box, lifter base, inner primary, timing plug, motor 

mounts and point cover 


36350 Smooth 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

Chrome Heim Joints 

These flawlessly-plated units can serve 

a variety of uses, particularly when 

fabricating custom shift and brake 

linkages. The 5/16" heim joints are 

available with right and left hand threads 

to make links that are adjustable without 

disassembly. Made in the U.S.A. Sold each. 

19297 1/4" x 1/4-28 female 

19298 5/16" x 5/16-24 male 


19302 5/16" x 5/16-24 male (left hand 

thread) 


Chrome Swingarm Pivot Bolts 

for Softail Models 

Chrome hex head swingarm pivot bolts. 

Grade 8 bolts measure 3/4"-16 x 3"-long. 

Fit Softail models from 84-99. Sold in pairs. 

84378 Swingarm Pivot Bolts 

Swingarm Pivot Bolt Spacers 

for Softail Models 

Fit Softail models from 87-99. Pack of 10. 

84602 Swingarm Pivot Bolt Spacers 

35636 35637 35638 

Transmission Case Bottom 

Studs 

Standard and two oversized sizes for 

Big Twin models from 36-83 (parkerized 

finish). Sold in sets of 4. 

35636 3/8"-16 x 3/8"-24 

35637 7/16"-14 x 3/8"-24 

35638 1/2"-13 x 3/8"-24 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Chrome Hardware Kits for Twin 

Cam Models 

Whether you are looking to turn your new 

Twin Cam model into a show bike or just to 

add that extra sparkle of chrome, Custom 

Chrome has you covered. From complete 

kits to individual sections for your motor or 

transmission. 

Complete Kits for Motor and 

Transmission Dyna Glide Models 

32069 Fits Dyna Glide models from 99-05 

– smooth 

612358 Fits Dyna Glide and Softail models 

from 07-17 – knurled 


from 07-17 – smooth 

Softail Models 

612282 Fits Softail models from 99-06 - 

knurled 





Touring Models 

612283 Fits Touring models from 99-06 – 

knurled 

612361 Fits Touring models from 07-16 - 

smooth 

Individual Kits 

These individual hardware kits are the 

same as the ones found in the complete 

kits. All hardware is sockethead unless 

otherwise specified. 

Side Cover Bolt Kits – Includes primary, 

cam, derby, and transmission cover 

bolts 

612293 Fits Softail models from 00-06 – 

knurled 

612351 Fits Softail 99-06, Dyna 99-05 – 

smooth 

612353 Fits Touring models from 07-16 – 

smooth 

Motor Mount Bolt Kits 

612288 Lower motor mount bolts for 

Softail models from 00-06 – 

knurled 

612289 Top motor mount bolts for Softail 

models from 00-06 – knurled 

Motor Mount Bolt Kits continued 

612327 Top motor mount bolts for Softail 


612330 Top motor mount bolts for 

Touring models from 07-16 – 

smooth 

Cam Cover 

Case Bolt Kits 

612307 Fits Dyna Glide 06-17 and Touring 


612306 Fits Softail models from 07-17 - 

smooth 

Rocker Box Covers 


- knurled 

612292 Fits Big Twin Evolution models 


612319 Fits Dyna Glide, Softail, and 

Touring models from 99-Up - 

smooth 

Lifter Blocks 

612446 Fits all 99-17 Touring models 


- smooth 

Primary Cover 







Transmission Mounting Plate Bolt Kit 

612356 Fits all Big Twin models (except 

Twin Cam) – knurled 

612357 Fits all Big Twin models (except 

Twin Cam) - smooth 

Sprocket/Pulley Mounting Kits 

612445 Sprocket mounting kit 7/16 x 2 1/2 

allenhead, custom applications 

Miscellaneous Kits 

32072 Fits clutch cover for Dyna Glide 

models from 99-05 

32073 Fits inspection cover for Dyna 

Glide models from 99-05 

612315 Fits derby cover for Dyna Glide, 

Softail, and Touring models from 

99-17 

612451 

612452 

Brake Caliper Mounting Kits for Twin Cams 

Quality chrome plated mounting bolts. Sold in pairs. Dual disc applications will require two sets. 

612450 Front caliper mounting bolts for all 00-07 models (except Springer) 

612451 Front caliper mounting bolts for 08-23 Touring, 09-13, 19-23 Trike knurled 

612452 Front caliper mounting bolts for 08-23 Touring, 09-13, 19-23 Trike smooth 



APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

HAND 

CONTROLS 

Chrome Hardware Sets 

These sets dress-up your bike with topquality 

chrome-plated hardware for a big 

improvement over stock cadmium-plated 

or old rusty hardware. Kits come with 

smooth or knurled sockethead hardware 

Handlebar Controls 

Fit all models from 82-95 (master cylinder 

screws fit 85-95) 

32755 Smooth 

32754 Knurled 

Driver/Passenger Footpeg Bolts 

Fit all Sportster and Big Twin models (set 

of two 3/8"-16 x 1 1/2" bolts and nyloninserted 

lock nuts) 

32764 Smooth 

Riser Bolts 

Sets of two riser bolts with hex, Torx or 

12-point heads. 

For Softail Models from 84-99 

A pair of 1/2"-13 x 2 1/2" bolts (repl. OEM 

3450) 

32767 Hex 

32769 Chromed torx bolts (sold in pairs) 

32771 Chromed 12-point bolts (sold in 

pairs) 

For FXR and Dyna Glide Models from 

91-17 

A pair of 1/2"-13 x 2 3/4" bolts (repl. OEM 

3471) 

32768 Hex 

Colony Acorn Kits 

Chrome-plated acorn-style hardware kits 

for specific applications. 

36157 Cam cover screws for 57-70 


36130 Kickstart cover kit for 4-speed Big 

Twins from 36-86 

36133 Sprocket cover kit for 71-76 


36144 Cylinder base nuts for 36-77 Big 

Twins 

36178 Cylinder base nuts for 78-84 

Shovelheads 

36163 Lifter base screws for 57-85 


36149 Lifter base screws for 36-75 Big 

Twins 

36150 Lifter base screws for 76-84 

Shovelheads 

36177 Lifter base screws to mount late 

lifter blocks to Big Twins with 

early engine cases 

36151 Rocker box nuts for 66-84 Big 

Twins 

36161 Rocker box bolts for 57-76 


36162 Rocker box bolts for 77-85 


36154 Lower motor mount kit for 

4-speed Big Twins from 36-84 

36155 Top motor mount kit for 4-speed 

Big Twins from 36-84 

36164 Motor mount kit for 57-E84 


36152 Head bolt kit for Big Twin models 

(except Evolution models) from 

48-84 

36156 Transmission plate-to-frame kit 

for 4-speed Big Twins from 36-86 

72057 Timing cover kit for Evolution Big 

Twins from 93-99 

Colony Chrome Hardware Kits 

Original Equipment-style replacement 

hardware kits. Available chrome-plated. 

36074 Slotted lifter base screws with 

starwashers for 36-53 OHV Big 

Twins 

36075 Cylinder base nuts for 36-78 OHV 

Big Twins 

36076 Cylinder base nuts for 45" 

engines and Sportster models 

36079 Transmission side cover and 

clutch arm kit for all 4-speed Big 

Twins thru 86 

36080 Timing plug 

36081 Case drain plug for all Big Twins 

from 30-99 

36082 Transmission filler plug for all 

40-86 4-speed Big Twins 

72070 Transmission filler/dipstick for Big 

Twins 87-05 (repl. OEM 37075-87) 

36083 Kicker spring stud 

36088 Case kit for 48-64 Panheads 

36090 Case kit for 70-78 Shovelheads 

36091 Case kit for Big Twins 79-84 

72068 Flanged nut and stud case kit for 

Evolution Big Twins from 96-99 

36093 Slotted transmission top cover 

screws for OHV Big Twins from 

36-64 

36095 Generator screws for Big Twin 

models from 36-57 

36096 Generator screws for 58-69 Big 

Twins 

36097 Slotted tin primary cover screws 

for Big Twins from 36-64 

36100 Upper and lower motor mount 

kit for Big Twins from 36-69 

36101 1/4" Flatwashers (pack of 12) 




LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

Shock Mounting Kit for Softail 

Models 

Includes precision-machined shoulder 

bolts and washers for the correct 

installation of rear shock absorbers on all 

Softail models from 84-99. 

28399 Cadmium-plated (set of 4) 

Chrome Axle Adjusters for 

Softail Models 

Sold in pairs. 3/8“ UNC 

35629 Fits Softail models from 93-99 

(replaces OEM 47579-93) 

36198 Fits Softail models from 86-92 

(replaces OEM 47579-86) 


Krommets 

Show-chromed studded Krommets. Longpopular, 

classic dress-up hardware for 

chrome dresser panels and accessories. 

Sold on a display card of 10 pairs. 

12291 Krommets 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 




Chrome-Plated ‘Grade 8’ 

Sockethead Screws 

• Assortments contain 24 sizes of UNC or 

UNF sockethead screws 

• Can be re-ordered in individual packs of 

10 of each size 

32100 Complete assortment (coarse – 

215 pieces) 

32101 Complete assortment (fine – 215 

pieces) 

COARSE FINE 

SIZE 

32103 32127 1/4" x 5/8" 

32104 32128 1/4" x 3/4" 

32105 32129 1/4" x 7/8" 

32106 32130 1/4" x 1" 

32107 32131 1/4" x 1 1/4" 

32108 32132 1/4" x 1 1/2" 

32109 32133 1/4" x 1 3/4" 

32110 1/4" x 2" 

32111 32135 1/4" x 2 1/4" 

32112 32136 5/16" x 5/8" 

32113 32137 5/16" x 3/4" 

32114 32138 5/16" x 7/8" 

32115 32139 5/16" x 1" 

32116 32140 5/16" x 1 1/4" 

32117 32141 5/16" x 1 1/2" 

32118 32142 5/16" x 1 3/4" 

32119 32143 5/16" x 2" 

32120 32144 5/16" x 2 1/4" 

32121 3/8" x 3/4" 

32122 32146 3/8" x 1" 

32123 32147 3/8" x 1 1/4" 

32124 32148 3/8" x 1 1/2" 

32125 32149 3/8" x 1 3/4" 

32126 32150 3/8" x 2" 

Chrome-Plated Grade 8 

‘Smooth’ Sockethead Screws 

• Assortments contain 24 sizes of UNC or 

UNF sockethead screws with polished 

“smooth” heads 



32200 Complete assortment (coarse – 

215 pieces) 

32201 Complete assortment (fine – 215 

pieces) 

COARSE FINE SIZE 

32203 32227 1/4" x 5/8" 

32204 32228 1/4" x 3/4" 

32205 1/4" x 7/8" 

32206 32230 1/4" x 1" 

32207 32231 1/4" x 1 1/4" 

32208 1/4" x 1 1/2" 

32209 1/4" x 1 3/4" 

32210 1/4" x 2" 

32211 32235 1/4" x 2 1/4" 

32212 32236 5/16" x 5/8" 

32213 32237 5/16" x 3/4" 

32214 32238 5/16" x 7/8" 

32215 5/16" x 1" 

32216 32240 5/16" x 1 1/4" 

32217 32241 5/16" x 1 1/2" 

32218 32242 5/16" x 1 3/4" 


32220 32244 5/16" x 2 1/4" 

32221 32245 3/8" x 3/4" 

32222 3/8" x 1" 

32223 3/8" x 1 1/4" 

32224 32248 3/8" x 1 1/2" 

32225 3/8" x 1 3/4" 

32226 32250 3/8" x 2" 

Chrome-Plated ‘Grade 8’ Torx 


• Available with smooth or knurled 

finishes 

SMOOTH KNURLED SIZE 

33304 1/4"-20 x 1" 

33311 1/4“-20 x 2 1/4“ 

33337 5/16"-18 x 1 1/4" 

33338 629537 5/16"-18 x 1 1/2" 

33339 33318 5/16"-18 x 1 3/4" 

33350 33319 3/8"-16 x 1 1/4" 

Chrome-Plated Low Crown 

Acorn Nuts 

• Assortment tray contains 16 sizes 

of UNC or UNF low crown acorn 

nutsChrome-Plated Low Crown Acorn 

Nuts 

• Assortment tray contains 16 sizes of 

UNC or UNF low crown acorn nuts 


5 or 10 for select sizes 

629536 Complete assortment (130 pieces) 

PART# 

SIZE 

629537 8 x 32 

629538 10 x 24 

629540 12 x 24 

629541 1/4” x 20 

629542 1/4” x 28 

629543 5/16” x 18 

629544 5/16” x 24 

629545 3/8” x 16 

629546 3/8” x 24 

629547 7/16” x 14* 

629548 7/16” x 20* 

629549 1/2” x 13* 

629550 1/2” x 20* 

629551 5/8” x 11* 

629552 5/8” x 18* 

*pack of 5

APPAREL 

629509 

SEATS & 

TOURING 

629554 

FOOT 

CONTROLS 

Chrome-Plated Jam Nuts 

Part# Size 

629554 1/4" x 20 

629556 5/16" x 18 

629557 5/16" x 24 

629558 3/8" x 16 

629559 3/8" x 24 

629561 7/16" x 20* 

629562 1/2" x 13* 

629563 1/2" x 20* 

*pack of 5 

Chrome-Plated Flat Top Acorn 

Nuts 

Chrome-Plated Thin Pattern 

Nylon Insert Hex Nuts 

• Assortment tray contains 12 sizes of 

UNC or UNF nylon insert hex nuts 



PART# 

629500 

SIZE 

Complete assortment (120 

pieces) 

629501 1/4” x 20 Coarse 

629502 1/4” x 28 Fine 

629503 5/16” x 18 Coarse 

629504 5/16” x 24 Fine 

629505 3/8” x 16 Coarse 

629506 3/8” x 24 Fine 

629507 7/16” x 14 Coarse 

629508 7/16” x 20 Fine 

629509 1/2” x 13 Coarse 

629510 1/2” x 20 Fine 

629511 5/8” x 11 Coarse 

629512 5/8” x 18 Fine 


Buttonhead Screws 

PART # SIZE QTY 

33381 8-32 x 1/2" 10 

33382 8-32 x 5/8" 10 

33383 10-24 x 1/2" 10 

33384 10-32 x 1/4" 10 

33385 10-32 x 1/2" 10 

33386 1/4"-20 x 5/8" 10 

33387 1/4"-20 x 3/4" 10 

33388 1/4"-20 x 7/8" 10 

33389 1/4"-20 x 1" 10 

33390 1/4"-20 x 2 1/2" 10 

33391 1/4"-28 x 1/2" 10 

33393 5/16"-18 x 1/2" 10 

33394 5/16"-18 x 3/4" 10 

33395 5/16"-18 x 1" 10 

33396 5/16"-18 x 1 1/4" 10 

33397 5/16"-24 x 1/2" 10 

33398 5/16"-24 x 1" 10 

33399 3/8"-16 x 1" 10 

33400 3/8"-16 x 1 1/4" 10 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

PART# SIZE PACK OF 

629523 1/4” x 20 10 

DRIVELINE 

629525 1/4” x 28 10 

629526 5/16” x 18 10 

629527 5/16” x 24 10 

WHEELS, TIRES 

& BRAKES 

629528 3/8” x 16 10 

629529 3/8” x 24 10 

629531 7/16” x 20* 9 5 

629532 1/2” x 13* 5 

629534 5/8” x 11* 5 

Stainless Steel Nuts and Washers 

• Pack of 50 of each size 

PART # 

SIZE 

Chrome-Plated Nuts and Washers 

• Assortment contains 1200 pieces of fine 

and coarse hardware in the sizes listed 

below 



25070 Complete assortment 

FRAMES 

FORKS & 

SHOCKS 

32361 1/4" Lock washer 

PART # 

SIZE 

SHEETMETAL 

32362 1/4" Flat washer 




32368 1/4"-28 Hex nut 

32370 5/16"-24 Hex nut 

32372 3/8"-24 Hex nut 







25179 1/4"-20 Hex nut 

25182 1/4"-28 Hex nut 

25180 5/16"-18 Hex nut 

25183 5/16"-24 Hex nut 

25181 3/8"-16 Hex nut 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



Chrome Flat Washer 

Assortment 

• Compartmented assortment 

trays include sizes and 

quantities of parts listed as 

components 

• Components can be reordered 

in individual packs 

of each size (refill quantities 

listed) 



32812 1/4" AN 50 

32813 5/16" AN 50 

32814 3/8" AN 50 

32815 7/16" SAE 25 

32816 1/2" SAE 25 

32818 #10 USS 25 

32819 1/4" USS 25 

32820 5/16" USS 25 

32821 3/8" USS 25 

32822 7/16" USS 25 

32823 1/2" USS 25 

32824 1/4" x 7/8" 25 

32825 1/4" x 1" 25 

32826 

5/16" x 1 

1/2" 

25 

32827 3/8" x 1 1/4" 25 

Chrome 7/16" and 

1/2" Bolt Assortment 

Trays 

• Compartmented assortment 

trays include sizes and 

quantities of parts listed as 

components 

• Components can be reordered 


of 5 of each size 

32830 7/16" and 1/2" coarse 

(UNC) hex bolt 

assortment 

32845 7/16" and 1/2" fine 

(UNF) hex bolt assortment 

COARSE FINE SIZE 

32831 32846 7/16" x 1" 

32832 32847 7/16" x 1 

1/4" 

32833 32848 7/16" x 1 

1/2" 

32834 32849 7/16" x 1 

3/4" 

32850 7/16" x 2" 

32836 32851 1/2" x 3/4" 

32837 32852 1/2" x 1" 

32838 

1/2" x 1 

1/4" 

32839 32854 1/2" x 1 

1/2" 

32843 32855 1/2“x 2 

3/4“ 

32841 32856 1/2" x 2 

1/4" 

32842 32857 1/2" x 2 

1/2" 

32844 32858 1/2" x 2 

*pack of 5 

Chrome-Plated 

Spacers 

90-piece assortment of 

chrome-plated steel spacers 

to fit screws with 1/4", 5/16" 

and 3/8” diameter. Can be reordered 




14642 1/4" x 1/8" 5 

14643 1/4" x 1/4" 5 

14644 1/4" x 3/8" 5 

14645 1/4" x 1/2" 5 

14646 1/4" x 3/4" 5 

14647 1/4" x 1" 5 

14648 5/16" x 1/8" 5 

14649 5/16" x 1/4" 5 

14650 5/16" x 3/8" 5 

14651 5/16" x 1/2" 5 

14652 5/16" x 3/4" 5 

14653 5/16" x 1" 5 

14654 3/8" x 1/8" 5 

14655 3/8" x 1/4" 5 

14656 3/8" x 3/8" 5 

14657 3/8" x 1/2" 5 

14658 3/8" x 3/4" 5 

14659 3/8" x 1" 5 


‘Grade 8’ Buttonhead 


• Assortment contains 24 sizes 

of UNC and UNF buttonhead 

screws 

• Can be re-ordered in 

individual packs of each 

size (refill quantities listed 

below) 


(fine and coarse – 240 

pieces) 


32301 8-32 x 1/2" 10 

32302 8-32 x 5/8" 10 

32303 8-32 x 3/4" 10 

32304 10-24 x 1/2" 10 

32305 10-32 x 1/2" 10 

32306 10-32 x 3/4" 10 

32307 10-32 x 1" 10 

32308 1/4"-20 x 5/8" 10 

32309 1/4"-20 x 3/4" 10 

32310 1/4"-20 x 7/8" 10 

32311 1/4"-20 x 1" 10 

32317 1/4"-28 x 1/2" 10 

32318 1/4"-28 x 3/4" 10 

32319 1/4"-28 x 1" 10 

32312 

32313 

5/16"-18 x 

1/2" 

5/16"-18 x 

3/4" 

10 

10 

32314 5/16"-18 x 1" 10 

32320 

32321 

5/16"-24 x 

3/8" 

5/16"-24 x 

1/2" 

10 

10 

32322 5/16"-24 x 1" 10 

32315 3/8"-16 x 3/4" 10 

32316 3/8"-16 x 1" 10 

32323 3/8"-24 x 3/4" 10 



32324 3/8"-24 x 1" 10

APPAREL 

SEATS & 

TOURING 



• Individual packs of each size 


Polished Stainless Steel Hex 

Head Capscrews 

• Individual packs of 10 of each size 

COARSE FINE 

SIZE 

FOOT 

CONTROLS 

HAND 

CONTROLS 

32727 8-32 x 1/2" 10 

32404 32428 1/4" x 3/4" 

32728 8-32 x 5/8" 10 

32729 8-32 x 3/4" 10 

32410 32434 1/4" x 2" 

32413 5/16" x 3/4" 

LIGHTING 

32730 10-24 x 1/2" 10 

32731 10-32 x 1/2" 10 

32438 5/16" x 7/8" 

32446 3/8" x 1" 

ELECTRICAL 

32732 10-32 x 3/4" 10 

32423 3/8" x 1 1/4" 

32733 10-32 x 1" 10 

32737 1/4"-20 x 1" 10 

32738 1/4"-28 x 1/2" 10 

32742 5/16"-18 x 3/4" 10 

32746 5/16"-24 x 1" 10 

32748 3/8"-16 x 1" 10 

32750 3/8"-24 x 1" 10 

Chrome Long Buttonhead 

Screws 

PART # SIZE 

32051 1/4"-20 x 1 1/4" 5 

32052 1/4"-20 x 1 1/2" 5 

32053 1/4"-20 x 1 3/4" 5 

32054 1/4"-20 x 2" 5 

32055 1/4"-20 x 2 1/2" 5 

32056 5/16"-18 x 1 1/4" 5 

32057 5/16"-18 x 1 1/2" 5 

32058 5/16"-18 x 2" 5 

32059 3/8"-16 x 1 1/4" 5 

32060 3/8"-16 x 1 1/2" 5 

32061 3/8"-16 x 1 3/4" 5 

32062 3/8"-16 x 2" 5 

32063 3/8"-16 x 2 1/4" 5 

QTY 

Chrome Countersunk 


• Compartmented assortment trays 

include sizes and quantities of parts 

listed below 

• Components can be re-ordered in 

individual packs of each size (refill 

quantities listed) 


PART # SIZE 

QTY 

32787 8-32 x 1/2" 10 

32788 8-32 x 5/8" 10 

32789 8-32 x 3/4" 10 

32790 10-24 x 1/2" 10 

32791 10-24 x 3/4" 10 

32794 10-32 x 3/4" 10 

32795 1/4"-20 x 1/2" 10 

32796 1/4"-20 x 5/8" 10 

32797 1/4"-20 x 3/4" 10 

32798 1/4"-20 x 1" 10 

32799 1/4"-20 x 1 1/2" 10 

32800 5/16"-18 x 1/2" 10 

32802 5/16"-18 x 3/4" 10 

32803 5/16"-18 x 1" 10 

32804 5/16"-18 x 1 1/4" 10 

32805 5/16"-24 x 5/8" 10 

32807 5/16"-24 x 1" 10 

32808 3/8"-16 x 3/4" 10 

32809 3/8"-16 x 1" 10 

32810 3/8"-24 x 1" 10 

32426 3/8" x 2" 

Stainless-Steel ‘Smooth’ 


• Individual packs of 10 of each size 

COARSE FINE 

SIZE 

32629 1/4" x 7/8" 

32630 1/4" x 1" 

32631 1/4" x 1 1/4" 

32632 1/4" x 1 1/2" 

32633 1/4" x 1 3/4" 

32611 32635 1/4" x 2 1/4" 

32336 5/16" x 5/8" 

32637 5/16" x 3/4" 

32638 5/16" x 7/8" 

32639 5/16" x 1" 

32617 32641 5/16" x 1 1/2" 

32642 5/16" x 1 3/4" 


32620 32644 5/16" x 2 1/4" 

32621 32645 3/8" x 3/4" 

32623 32647 3/8" x 1 1/4" 

32624 3/8" x 1 1/2" 

32626 3/8" x 2" 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

32064 3/8"-16 x 2 1/2" 5 

32065 3/8"-16 x 2 3/4" 5 

LUBRICANTS & 

CHEMICALS 

32066 3/8"-16 x 3" 5 

TOOLS & 

EQUIPMENT 






‘Grade 5’ Hex Head 

Capscrews 

• Assortments contain 24 sizes 

of UNC or UNF capscrews 

• Can be re-ordered in 

individual packs of 10 of 

each size 


(coarse – 220 pieces) 


(fine – 220 pieces) 

COARSE FINE 

SIZE 

25125 1/4" x 5/8" 

25126 25150 

25127 25151 

1/4" x 

3/4" 

1/4" x 

7/8" 

25128 25152 1/4" x 1" 

25129 

25130 25154 

25155 

1/4" x 1 

1/4" 

1/4" x 1 

1/2" 

1/4" x 1 

3/4" 

25132 1/4" x 2" 

25134 25158 

25135 25159 

25136 25160 

5/16" x 

5/8" 

5/16" x 

3/4" 

5/16" x 

7/8" 

25137 25161 5/16" x 1" 

25138 25162 

25139 25163 

25140 

5/16" x 1 

1/4" 

5/16" x 1 

1/2" 

5/16" x 1 

3/4" 

25141 5/16" x 2" 

25142 25166 

25143 

5/16" x 2 

1/4" 

3/8" x 

3/4" 

25144 25168 3/8" x 1" 

25145 25169 

25146 25170 

25147 25171 

3/8" x 1 

1/4" 

3/8" x 1 

1/2" 

3/8" x 1 

3/4" 

25148 25172 3/8" x 2 

Coarse and Fine Thread Nuts/Screws & 

Spacers & Flat-/Lock Washers 

Available for coarse thread and fine thread products. 

I 

PART # DESCRIPTION SIZE QTY 

68037 Lockwashers 1/4"-20 4 

68038 Lockwashers 5/16" 4 


68041 Flatwashers 1/4"-20 4 

68042 Flatwashers 5/16" 4 


68086 Steel Spacers 3/8" x 1/8" 2 


68003 Acorn Nuts 5/16"-18 4 

68005 Acorn Nuts 7/16"-14 2 

68008 Smooth Sockethead 1/4"-20 x 3/4" 2 

68010 Smooth Sockethead 1/4"-20 x 1" 2 

68011 Smooth Sockethead 1/4"-20 x 1.25" 2 










68033 Hex Nut 1/4"-20 4 

68034 Hex Nut 5/16"-18 4 

68044 Bumper Bolt 1/4"-20 x 1" 2 

68114 Bumper Bolt 7/16"-14 x 2" 1 

68060 Nylok Nuts 1/2"-13 2 

68061 Buttonhead 8-32 x 1/2" 2 

68064 Buttonhead 10-24 x 1/2" 2 

68068 Buttonhead 1/4"-20 x 1" 2 

68069 Buttonhead 5/16"-18 x 1/2" 2 

68072 Buttonhead 3/8"-16 x 3/4" 2 

68073 Buttonhead 3/8"-16 x 1" 2 

68111 Hex Head 3/8"-16 x 1.5" 2 

68202 Acorn Nuts 1/4"-28 4 

68203 Acorn Nuts 5/16"-24 4 

68205 Acorn Nuts 7/16"-20 2 





68219 Smooth Sockethead 5/16"-24 x 1.25" 2 

68232 Hex Nut 3/8"-24 4 

68247 Nylok Nuts 3/8"-24 2 

68254 Buttonhead 1/4"-28 x 5/8" 2 

68258 Buttonhead 5/16"-24 x 1/2" 2 

68260 Buttonhead 5/16"-24 x 1" 2 

68270 Hex Head 1/4"-28 x 2" 2 

68279 Hex Head 3/8"-24 x 3/4" 2 

68281 Hex Head 3/8"-24 x 1.25" 2 

Custom Chrome Hardware 

Kits 

Assorted chrome nuts, bolts, washers and 

spacers. 

PART # DESCRIPTION SIZE QTY 

68003 Acorn Nuts 5/16"-18 4 

68033 Hex Nut 1/4"-20 4 

68034 Hex Nut 5/16"-18 4 

68041 Flatwashers 1/4"-20 4 



68064 Buttonhead 10-24 x 1/2" 2 

68068 Buttonhead 1/4"-20 x 1" 2 


68111 Hex Head 

3/8"-16 x 

1.5" 

68003 Acorn Nuts 5/16"-18 4 

68008 Smooth 

Sockethead 

68010 Smooth 

Sockethead 

68020 Smooth 

Sockethead 

68023 Smooth 

Sockethead 

1/4"-20 x 

3/4" 

2 

2 

1/4"-20 x 1" 2 

5/16"-18 x 

1.5" 

3/8"-16 x 

3/4" 

68033 Hex Nut 1/4"-20 4 

68034 Hex Nut 5/16"-18 4 

68037 Lockwashers 1/4"-20 4 



68041 Flatwashers 1/4"-20 4 



68064 Buttonhead 10-24 x 1/2" 2 

68068 Buttonhead 1/4"-20 x 1" 2 


68111 Hex Head 3/8"-16 x 1.5" 2 

2 

2

APPAREL 

SEATS & 

TOURING 

FOOT 

CONTROLS 

Lowbrow Customs Logo Banner 

Super cool, Lowbrow Customs banner. 47” x 17”, vinyl, 

weatherproof brass grommets in each corner. Good for your 

shop or anywhere you feel the need. 

607548 Lowbrow Customs Logo Banner, 47” x 17” 

HAND 

CONTROLS 

LIGHTING 

ELECTRICAL 

Sign by James Gaskets 

667126 Embossed Metal, GENUINE Logo, 61 x 28 cm 

Lowbrow Customs Weirdo Banner 

Big 30” x 30”, vinyl and weatherproof banners with brass 

grommets in each corner. Perfect for the garage or shop. Proud 

to be a Lowbrow Weirdo! 

607549 Lowbrow Customs Weirdo Banner 30” x 30” 

EXHAUST 

INTAKE 

ENGINE 

GASKETS 

TRANNY & 

CLUTCH 

DRIVELINE 

Service & Repair Manual 

• Clear and easy to follow page layout 

• Full procedures written from hands-on experience 

• Easy-to-follow photos 

• Faultfinding information 

• How to make special tools 


899566 899567 899568 

WHEELS, TIRES 

& BRAKES 

FRAMES 

FORKS & 

SHOCKS 

PART# FITMENT DESCRIPTION 

899566 70-84 FL Shovel, 71-84 FX Shovel, 85-94 FX Model, For Shovelhead and Evolution Big Twins (70-99) 

91-98 Dyna, 84-99 Softail, 86-99 Touring 

899567 70-13 Sportster For Sportsters XL, XLH, XLCH, XLS and XLX with 883/1000/1100 and 

1200 engines (70-13) 

899568 99-10 Dyna, 99-10 Softail, 99-10 Touring For Twin Cam 88 covering Softail (00-10), Dyna Glide (99-10), and 

Electra Glide/Road King and Road Glide (99-10) 

SHEETMETAL 

INSTRUMENTS 

& GAUGES 

LUBRICANTS & 

CHEMICALS 

TOOLS & 

EQUIPMENT 



6890423 

642983 

6890421 

6890422 


6890418 

6890427 

6890402 

6890425 

6890430 

6890424 

6890420 

6890389 

914901 

899564 

6890431 

913636 

899565 

REPAIR MANUALS 

• Most complete repair manuals available outside of the factory 

• Presented in everyday, clear, straightforward language 

• Dimensions: 7 1/2“ x 10“ 

• Packs everything from tips to complete wiring diagrams 

• Illustrated with hundreds of photos, drawings and charts 

• Clear, easy-to-follow, step-by-step explanations 

Unit: Each 

PART# FITMENT DESCRIPTION 

6890423 00-05 Softail For Softail Series 00-05 

642983 02-14 V-Rod For V-Rod Series 02-14 

6890427 04-11 Sportster For Sportster Series 04-11 

6890402 06-09 Touring For Touring Series 06-09 


6890431 06-11 Dyna For Dyna Series 06-11 





921208 17-19 Touring For Touring Series 17-19 

6890418 48-65 Panhead For Panhead Series 48-65 

6890419 59-85 Sportster For Sportster Series 59-85 

6890420 66-84 FL Shovel, 71-84 FX Shovel 


6890422 85-94 FX Model 





921208 

6890429

Section 19 Custom Chrome Europe Catalog 2024

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?