vdoc
Index TermsLinkssines, law of 33–34single sampling plans 155 156Six Sigma 318–19skew, of data set 205–6snap gages 70–71softwarein machine vision systems 107verification, for test equipment 196–97sorting 151spaces, confined 321–22special causes 258–61specification limits, versus control limits 261spline gages 71square, of a number 9square root 9–10stability 85 124standard deviation 209–11standard normal distribution 238–39standard normal distribution table 239–45 385–86(Appendix D)standard normal random variable 238standards, reference 322–23Starlink seed corn, contamination incident 173statistical process control (SPC) 246–303statisticsbasic, and applications 200–245versus parameters 200steel rule 59Sturgis’s formula 218supplementary angles 26surface area, of basic geometric shapes 25–26surface characteristics 96This page has been reformatted by Knovel to provide easier navigation.
Index TermsLinkssurface finishgages 98–99measuring 98–100surface metrology 96–98surface plateangle measurement instruments 91–93equipment 89–91surface quality specifications 96–98switching procedures, in sampling 156system audit 309systematic errors 167Tteamsroles and responsibilities 326–27stages of development 327–28technical mathematics 2–55technical reports 323–24templates 71tensile testing 187–88tension test 187–88 191test equipment, verification of software for 196–97testingand inspection 137–97versus inspection 197methods 180–97thread plug gages 71thread snap gages 71tolerance(s) 140–43tolerance of position control 147torque testing 191traceabilityequipment 119product 170–73This page has been reformatted by Knovel to provide easier navigation.
- Page 356 and 357: How to Use This BookTo assist reade
- Page 358 and 359: 2 Test Questions5. Solve the follow
- Page 360 and 361: 4 Test Questions14. The figure belo
- Page 362 and 363: 6 Test Questions23. The volume of a
- Page 364 and 365: 8 Test Questions35. The vernier cal
- Page 366 and 367: 10 Test Questions48. Which of the f
- Page 368 and 369: 12 Test Questions62. What number in
- Page 370 and 371: 14 Test Questions73. The process ca
- Page 372 and 373: 16 Test Questions85. A manufacturer
- Page 374 and 375: 18 Test Questions95. Which of the f
- Page 376 and 377: 20 Test Questions108. The quality t
- Page 378 and 379: 22 Test Questions121. Which of the
- Page 380 and 381: 24 Test Questions133. In an FMEA, w
- Page 382 and 383: 26 Test Questions144. Accessing inf
- Page 385 and 386: Test Answer Key1. B28. C55. B82. C2
- Page 387 and 388: INDEXIndex TermsLinksAacceptance nu
- Page 389 and 390: Index TermsLinksCc chart 284-88cali
- Page 391 and 392: Index TermsLinksDdata set, skew of
- Page 393 and 394: Index TermsLinksfinal inspection 16
- Page 395 and 396: Index TermsLinkshierarchical design
- Page 397 and 398: Index TermsLinkslaw of sines 33-34l
- Page 399 and 400: Index TermsLinksmicrometer caliper
- Page 401 and 402: Index TermsLinksoutput, action on 2
- Page 403 and 404: Index TermsLinksQQS-9000 standards
- Page 405: Index TermsLinkssampling 150-61adva
- Page 409 and 410: Index TermsLinksvariance 208variati
- Page 411 and 412: Appendix AQuality Inspector Certifi
- Page 413 and 414: 334 Part V: Appendices2. Measuring
- Page 415 and 416: 336 Part V: Appendices5. Verificati
- Page 417 and 418: 338 Part V: AppendicesComprehension
- Page 419 and 420: 340 Part V: AppendicesFigure B.1 Th
- Page 421 and 422: 342 Part V: AppendicesSaving a Mini
- Page 423 and 424: 344 Part V: AppendicesEXAMPLE B.2Us
- Page 425 and 426: 346 Part V: Appendicesthe option Si
- Page 427 and 428: 348 Part V: AppendicesContinuedFigu
- Page 429 and 430: 350 Part V: Appendices(a) As shown
- Page 431 and 432: 352 Part V: AppendicesBar Chart. En
- Page 433 and 434: 354 Part V: AppendicesContinuedFigu
- Page 435 and 436: 356 Part V: AppendicesEXAMPLE B.11C
- Page 437 and 438: 358 Part V: AppendicesShewhart X -
- Page 439 and 440: 360 Part V: AppendicesContinuedTabl
- Page 441 and 442: 362 Part V: AppendicesThe p Chart:
- Page 443 and 444: 364 Part V: Appendicesmenu select S
- Page 445 and 446: 366 Part V: AppendicesContinued7. I
- Page 447 and 448: 368 Part V: AppendicesUnits of Leng
- Page 449 and 450: 370 Part V: AppendicesUnits of Volu
- Page 451 and 452: 372 Part V: Appendices3. NOTES ON B
- Page 453 and 454: 374 Part V: AppendicesUnits Square
- Page 455 and 456: 376 Part V: AppendicesUnits of Capa
Index Terms
Links
surface finish
gages 98–99
measuring 98–100
surface metrology 96–98
surface plate
angle measurement instruments 91–93
equipment 89–91
surface quality specifications 96–98
switching procedures, in sampling 156
system audit 309
systematic errors 167
T
teams
roles and responsibilities 326–27
stages of development 327–28
technical mathematics 2–55
technical reports 323–24
templates 71
tensile testing 187–88
tension test 187–88 191
test equipment, verification of software for 196–97
testing
and inspection 137–97
versus inspection 197
methods 180–97
thread plug gages 71
thread snap gages 71
tolerance(s) 140–43
tolerance of position control 147
torque testing 191
traceability
equipment 119
product 170–73
This page has been reformatted by Knovel to provide easier navigation.