Owner's Manual - Arrow Sheds
Owner's Manual - Arrow Sheds Owner's Manual - Arrow Sheds
26 Step 13 N26et (2) (6) Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer. NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the roof panels fit better, and holes will align. NOTE If a Roof Beef-Up Kit was purchased, assemble prior to attaching the roof panels. 1 Locate the roof panels and find the right roof panel. 2 Position a right roof panel at the back right corner and fasten to the top roof beam using a screw. ● Parts Needed For ● Right Roof Panel STEP 1 STEP 2 8579 7571 7571 8578 FRONT Washer Gable Nut 2 6 Bolt ● 8578 Right Roof Panel (1) 1 2 3 4 5 7571 6 8578 7571 7743 8 7 7743 STEP 3 10 9 4 FRONT 1 5 3 8 8579 3 Remove edge trim from the left gable under the roof panel. 4 Continue fastening the right roof panel to the gable and lower roof beam using screws, bolts and nuts as shown. Do not fasten the lower end of the panels to the side wall angles at this time. STEP 4 Right Roof Panel 8578 Hint: Follow the fastener sequence shown for proper alignment. 7
Step 14 N27hw (38) (22) 1 Install a left roof panel at the left rear and right front corner of the roof. Install a right roof panel at the left front corner of the roof. 2 Cut 4 short 2" (5,1 cm) strips off the roll of weather stripping tape, and put them aside. Cover the joint at the peak with weather stripping tape. Unroll the tape and press it down over the opening at the ridge as you install each roof panel. Do not cut the tape at this time. 3 Install 2 narrow and 2 wide roof panels in the sequence and positions shown on previous page. Do not fasten the lower end of the panels to the side wall angles at this time. Continue weather stripping the ridge opening. NOTE Narrow roof panel crimped rib is overlapped by wide rib of adjacent panel where possible. NOTE If roof beam holes do not line up with the roof panel holes, shift the building from left to right. If this does not help, your building may not be level. Shim the corners until holes line up. ● Parts Needed For ● Roof Assembly 8579 Left Roof Panel 7571 Roof Panel 7743 Roof Panel 8578 Right Roof Panel Fasten At Overlap with Bolt FRONT Screws To Roof Beam STEP 1 Screws To Roof Beam Do not fasten at this time ● 8578 Right Roof Panel (1) ● 8579 Left Roof Panel (2) ● 7571 Roof Panel (2) ● 7743 Roof Panel (2) Weather Stripping Tape Roll Fasten At Overlap with Bolt STEP 2 7571 Roof Panel 7743 Roof Panel STEP 3 27
- Page 1 and 2: Owner's Manual & Assembly Instructi
- Page 3 and 4: A3 Watch the Weather: Be sure the d
- Page 5 and 6: A5 Web Finish: For long lasting fin
- Page 7 and 8: THIS PAGE WAS LEFT BLANK INTENTIONA
- Page 9 and 10: A09hw The Base For Your Building Ba
- Page 11 and 12: N11hw 65103 #8-32 Hex Nut (169) 660
- Page 13 and 14: 13 Assembly by Key No. N13et 20 20
- Page 15 and 16: Step 2 D15hw (6) The main frame pie
- Page 17 and 18: Step 4 A17hw END VIEW (4) The door
- Page 19 and 20: Step 6 L19hw (26) (4) NOTE The rema
- Page 21 and 22: Step 8 D21hw (112) (17) The wall pa
- Page 23 and 24: Step 10 N23et (8) The gables go on
- Page 25: Step 12 N25hw 1 Wrap the weather st
- Page 29 and 30: Step 16 A29hw (4) (8) (4) 1 Attach
- Page 31 and 32: Step 18 A31hw (8) 1 From inside the
- Page 33 and 34: 711680705 * Nombre de la pieza *Dé
- Page 35 and 36: • 1,6 cm Mindestdicke. Qualitäts
- Page 37: XC33hw SOME FACTS ABOUT RUST SOME F
26<br />
Step 13<br />
N26et<br />
(2) (6)<br />
Installing the roof panels is best done<br />
with a step ladder. Begin installing<br />
roof panels at the back right corner of<br />
the building. Each screw and bolt in<br />
the roof requires a washer.<br />
NOTE<br />
Measure the building diagonally<br />
again and make adjustments to<br />
make sure the building is square.<br />
This will make the roof panels fit<br />
better, and holes will align.<br />
NOTE<br />
If a Roof Beef-Up Kit was<br />
purchased, assemble prior to<br />
attaching the roof panels.<br />
1 Locate the roof panels and find the<br />
right roof panel.<br />
2 Position a right roof panel at the<br />
back right corner and fasten to the top<br />
roof beam using a screw.<br />
● Parts Needed For ●<br />
Right Roof Panel<br />
STEP<br />
1<br />
STEP<br />
2<br />
8579<br />
7571<br />
7571<br />
8578<br />
FRONT Washer<br />
Gable<br />
Nut<br />
2<br />
6<br />
Bolt<br />
● 8578 Right Roof Panel (1)<br />
1<br />
2 3<br />
4 5<br />
7571<br />
6<br />
8578<br />
7571<br />
7743 8<br />
7<br />
7743<br />
STEP<br />
3<br />
10 9<br />
4<br />
FRONT<br />
1<br />
5<br />
3<br />
8<br />
8579<br />
3 Remove edge trim from the left gable under<br />
the roof panel.<br />
4 Continue fastening the right roof panel to<br />
the gable and lower roof beam using screws,<br />
bolts and nuts as shown. Do not fasten the<br />
lower end of the panels to the side wall angles<br />
at this time.<br />
STEP<br />
4<br />
Right Roof Panel<br />
8578<br />
Hint: Follow the fastener sequence<br />
shown for proper alignment.<br />
7