Owner's Manual - Arrow Sheds
Owner's Manual - Arrow Sheds Owner's Manual - Arrow Sheds
Step 9 D22hw The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. 1 Fasten the front wall channels in their positions between the end of the side wall channel and the corner panel using screws. Do not put a screw in the hole at the end behind the door opening at this time. 2 Fasten a door jamb to the front panel with two bolts, nuts and acorn nuts, as shown. 3 Fasten the center of the door jamb to the front wall panel and the front wall channel with two screws. 4 Fasten the top of the door jamb to the door track with two screws. Do the same for the bottom into frame. Repeat steps 2 through 4 for the opposite door jamb. 22 (18) (4) ● Parts Needed For ● Front Channel/Door Jamb Acorn Nut Hex Nut Acorn Nut 9365 STEP 1 STEP 2 FRONT 9369 FRONT STEP 4 (2) bolts Bolt INSIDE OF BUILDING Screw ● 9369 Door Jamb (2) ● 9365 Front Wall Channel (2) TOP VIEW Door Track 9369 TOP VIEW Front Wall Channel Screw TOP VIEW Door Track Screw STEP 3 Front Wall Channel Cross-Section Top View Screw
Step 10 N23et (8) The gables go on top of the front and rear walls to support the roof beams. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. 1 Apply edge trim to the top edge of the right gables and left gables. 2 Attach the four roof beam brackets to the gables using two bolts, washers and nuts. NOTE Mounting leg of bracket must face toward center of gable CAUTION: To avoid mishap on the sharp edge the edge trim must remain in place on the top edge of the gable until right and left roof panels are in place. 8576 ● Parts Needed For ● Gable Assemblies STEP 2 STEP 1 Edge Trim (plastic piece) 8577 FRONT 8577 6635 Roof Beam Brackets ● 8576 Right Gable (2) ● 8577 Left Gable (2) ● 6635 Roof Beam Bracket (4) Washer 23
- Page 1 and 2: Owner's Manual & Assembly Instructi
- Page 3 and 4: A3 Watch the Weather: Be sure the d
- Page 5 and 6: A5 Web Finish: For long lasting fin
- Page 7 and 8: THIS PAGE WAS LEFT BLANK INTENTIONA
- Page 9 and 10: A09hw The Base For Your Building Ba
- Page 11 and 12: N11hw 65103 #8-32 Hex Nut (169) 660
- Page 13 and 14: 13 Assembly by Key No. N13et 20 20
- Page 15 and 16: Step 2 D15hw (6) The main frame pie
- Page 17 and 18: Step 4 A17hw END VIEW (4) The door
- Page 19 and 20: Step 6 L19hw (26) (4) NOTE The rema
- Page 21: Step 8 D21hw (112) (17) The wall pa
- Page 25 and 26: Step 12 N25hw 1 Wrap the weather st
- Page 27 and 28: Step 14 N27hw (38) (22) 1 Install a
- Page 29 and 30: Step 16 A29hw (4) (8) (4) 1 Attach
- Page 31 and 32: Step 18 A31hw (8) 1 From inside the
- Page 33 and 34: 711680705 * Nombre de la pieza *Dé
- Page 35 and 36: • 1,6 cm Mindestdicke. Qualitäts
- Page 37: XC33hw SOME FACTS ABOUT RUST SOME F
Step 10<br />
N23et<br />
(8)<br />
The gables go on top of the front and<br />
rear walls to support the roof beams.<br />
NOTE<br />
The gables are packed nested<br />
together and might be mistaken<br />
as one piece. Carefully separate<br />
them before continuing.<br />
1 Apply edge trim to the top edge of<br />
the right gables and left gables.<br />
2 Attach the four roof beam<br />
brackets to the gables using two<br />
bolts, washers and nuts.<br />
NOTE<br />
Mounting leg of bracket must<br />
face toward center of gable<br />
CAUTION:<br />
To avoid mishap on the sharp<br />
edge the edge trim must remain<br />
in place on the top edge of the<br />
gable until right and left roof<br />
panels are in place.<br />
8576<br />
● Parts Needed For ●<br />
Gable Assemblies<br />
STEP<br />
2<br />
STEP<br />
1<br />
Edge Trim<br />
(plastic piece)<br />
8577<br />
FRONT<br />
8577<br />
6635<br />
Roof Beam<br />
Brackets<br />
● 8576 Right Gable (2)<br />
● 8577 Left Gable (2)<br />
● 6635 Roof Beam Bracket (4)<br />
Washer<br />
23
Change language