Installation

Recommendations

Info

CHIME VOLTAGE OUTPUT The CH Terminal provides an output voltage whenever the chime button is pressed. The duration of this output voltage is set by 1 of 3 programming options. Chime Voltage Output Options ��Option #1 Single flash - Voltage present for duration of Bell Press ��Option #2 Double flash - Voltage present for duration of Chime ��Option #3 Triple flash - Voltage present for 10 seconds from moment of Bell Press The Chime Voltage output duration can be changed by means of the two programming switches (SEL and PROG) situated on the Door Station circuit board as indicated below. POS NEG COM1 COM2 U5 VR3 TC VLC SHLD VR1 SEL VR2 CH PROG PROCEDURE: Press the PROGRAM button (PROG) – The red L.E.D. illuminates and the current chime is played. Press the PROGRAM button again to select the CH output option mode – The red L.E.D. flashes the current output voltage option. Press the SELECT button (SEL) – The next output option is displayed. Repeatedly press the SELECT button until the desired CH output option is displayed. Press the PROGRAM button again to lock in the selection and exit program mode – The red L.E.D. extinguishes. Pressing the SELECT button after all 3 output options have been sampled will cycle back to output option #1. SEL PROG 83
SETTING UP INPUT JACK TYPE B If the Input Jack has been wired into an 8-wire system, ensure the jumper has been removed from the two link pins labelled "L1". If the Input Jack has been wired into a 6-wire system, ensure the jumper has been fitted across the two link pins labelled "L1". The volume control on the Input Jack should be adjusted for the desired volume at the intercom stations with the Room Station volume controls adjusted to approximately 3/4 of maximum. The tone control should be adjusted 1/2 way or to personal preference. SETTING UP WIRELESS AUDIO TRANSMITTER Turn on the intercom radio and press the MUSIC button at the Master, to enable MUSIC mode. Tune the intercom radio to one of the FM frequencies listed in the table below that is not being used by a commercial FM radio station. If a clear frequency cannot be found, use one that is picking up only a weak radio signal. Store this frequency into the memory of the intercom radio, as a "preset" station. Using the table below, program the four miniature programming switches on the Wireless Audio Transmitter to correspond with the FM frequency chosen. The output of the audio device should now be audible through the intercom Master. FREQUENCY SWITCH TABLE S1 S2 S3 S4 FREQ S1 S2 S3 S4 FREQ L L L L 87.7MHz L L L H 87.7MHz H L L L 87.9MHz H L L H 87.9MHz L H L L 88.1MHz L H L H 88.1MHz H H L L 88.3MHz H H L H 88.3MHz L L H L 88.5MHz L L H H 88.5MHz H L H L 88.7MHz H L H H 88.7MHz L H H L 88.9MHZ L H H H 88.9MHZ H H H L No Operation H H H H No Operation 84
Page 1 and 2:
HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4:
INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6:
VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8:
LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10:
AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12:
AM AERIAL The coaxial cable supplie
Page 13 and 14:
BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16:
INSTALLATION OF MASTER STATION TIMB
Page 17 and 18:
Mounting Brackets for Tamper Switch
Page 19 and 20:
CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22:
FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23 and 24:
INSTALLATION OF VR102 ROOM STATIONS
Page 25 and 26:
CABLE TERMINATION FOR VR102 ROOM ST
Page 27 and 28:
CABLE TERMINATION FOR VR102 ROOM ST
Page 29 and 30:
CABLE TERMINATION FOR VF 103 DOOR S
Page 31 and 32:
WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34:
Operating Automatic Gates AUTO GATE
Page 35 and 36:
4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
Page 53 and 54: Home Press the "ON" button two time
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76: Category When Chirp and/or Voice re
Page 77 and 78: IMPORTANT NOTES: To place the VM102
Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84: CHANGING THE CHIME The chime melody
Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
Page 87: CHANGING THE CHIME The chime melody
Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94: AUX ��Outputs specific voltage
Page 95: TROUBLE SHOOTING Fault: Volume Cont
show all

Installation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?