Installation
Installation Installation
PROGRAMMING AND ADJSTMENTS FOR VF103 DOOR STATION DOOR STATION ADJUSTMENTS There are 3 adjustments on the Door Station that may require fine-tuning after installation. A flat bladed screwdriver with a blade width between 2mm and 2.4mm is required for these adjustments. Using the wrong screwdriver will damage the pot. Speaker Volume Speaker volume at the Door Station is adjusted by means of a miniature trim pot (VR1) located in the centre of the circuit board. Turning this pot will vary the speaker volume. This adjustment can be made while someone is communicating to the Door Station from one of the internal stations or while the chime is activated. Chime Volume Chime volume is adjusted by means of a miniature trim pot (VR2) situated at the bottom of the circuit board as indicated below. Turning this pot will vary the chime volume throughout the entire system. This pot should be adjusted so the chime volume comes through at an acceptable level at an internal Room Station with its slide volume control set to around level 4 or 5. Microphone Gain The microphone gain pot (VR3) is generally set half way and would rarely require adjustment. The microphone level can be turned down where the Door Station causes feedback in a Room Station due to close proximity or can be turned up if the communication level from the Door Station is too low - see "Adjustments for VR102 Room Stations" for more detail. SEL PROG U5 E1 VR2 SPEAKER VOLUME CHIME VOLUME VR3 VR1 MICROPHONE GAIN . . LK + CH COM2 COM1 SHLD VLC TC NEG POS 77
CHANGING THE CHIME The chime melody can be changed to any one of ten options by means of the two programming switches (SEL and PROG) situated on the Door Station circuit board as indicated below. RED LED SEL PROG SEL PROG U5 E1 VR2 VR3 PROCEDURE: Press the PROGRAM button (PROG) – The red L.E.D. illuminates and the current chime plays. Press the SELECT button (SEL) – The next chime option plays. Repeatedly press the SELECT button until the desired melody is heard. Press the PROGRAM button to lock in selection – The red L.E.D. flashes. Press the PROGRAM button again to exit program mode – The red L.E.D. extinguishes. Pressing the SELECT button after all of the ten chime options have been sampled, will cycle back to the first chime option. VR1 . . LK + CH COM2 COM1 SHLD VLC TC NEG POS 78
- Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
- Page 33 and 34: Operating Automatic Gates AUTO GATE
- Page 35 and 36: 4-Wire Operation If only four wires
- Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
- Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
- Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
- Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
- Page 45 and 46: POWERING UP THE SYSTEM For the VM10
- Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
- Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
- Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
- Page 53 and 54: Home Press the "ON" button two time
- Page 55 and 56: KEY TYPES User Key ��3-button p
- Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
- Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
- Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
- Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
- Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
- Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
- Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
- Page 71 and 72: Main Unit The following events are
- Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
- Page 75 and 76: Category When Chirp and/or Voice re
- Page 77 and 78: IMPORTANT NOTES: To place the VM102
- Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
- Page 81: VR102 ROOM STATION ADJUSTMENTS MICR
- Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
- Page 87 and 88: CHANGING THE CHIME The chime melody
- Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
- Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
- Page 93 and 94: AUX ��Outputs specific voltage
- Page 95: TROUBLE SHOOTING Fault: Volume Cont
PROGRAMMING AND ADJSTMENTS FOR VF103 DOOR STATION<br />
DOOR STATION ADJUSTMENTS<br />
There are 3 adjustments on the Door Station that may require fine-tuning after installation.<br />
A flat bladed screwdriver with a blade width between 2mm and 2.4mm is required for these<br />
adjustments. Using the wrong screwdriver will damage the pot.<br />
Speaker Volume<br />
Speaker volume at the Door Station is adjusted by means of a miniature trim pot (VR1)<br />
located in the centre of the circuit board.<br />
Turning this pot will vary the speaker volume.<br />
This adjustment can be made while someone is communicating to the Door Station from<br />
one of the internal stations or while the chime is activated.<br />
Chime Volume<br />
Chime volume is adjusted by means of a miniature trim pot (VR2) situated at the bottom of<br />
the circuit board as indicated below.<br />
Turning this pot will vary the chime volume throughout the entire system.<br />
This pot should be adjusted so the chime volume comes through at an acceptable level at<br />
an internal Room Station with its slide volume control set to around level 4 or 5.<br />
Microphone Gain<br />
The microphone gain pot (VR3) is generally set half way and would rarely require<br />
adjustment.<br />
The microphone level can be turned down where the Door Station causes feedback in a<br />
Room Station due to close proximity or can be turned up if the communication level from<br />
the Door Station is too low - see "Adjustments for VR102 Room Stations" for more detail.<br />
SEL<br />
PROG<br />
U5<br />
E1<br />
VR2<br />
SPEAKER VOLUME<br />
CHIME VOLUME<br />
VR3<br />
VR1<br />
MICROPHONE GAIN<br />
. .<br />
LK<br />
+<br />
CH<br />
COM2<br />
COM1<br />
SHLD<br />
VLC<br />
TC<br />
NEG<br />
POS<br />
77