Installation
Installation
Installation
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
IMPORTANT NOTES:<br />
To place the VM102-SECURE into program mode simply remove and replace the shunt on<br />
the rear of the security PCB. The display will show the version number for 0.5 seconds<br />
then flash “LEARN” for 10 seconds. During the 10 seconds the display is flashing<br />
“LEARN”, pressing the “ON” button on any programmed key, will enable the VM102-<br />
SECURE to receive signals from radio devices (both keys and devices). “READY” will be<br />
flashing on the display.<br />
The VM102-SECURE programs the device or key into the next available position. For<br />
example, if there are already 4 sensors programmed, the next device will be programmed<br />
as sensor 5. If a sensor or key is deleted, the next sensor or key will be programmed in the<br />
erased position.<br />
Programming details<br />
��Programming Supervised / Encrypted PIR’s: With “READY” flashing on the display of<br />
the VM102-SECURE, connect the 9 volt Lithium battery to the PIR. The VM102-<br />
SECURE will respond with “BING-BING - BING-BING." The display will flash the<br />
sensor number programmed (eg. “SENS 2”). If you try to program the sensor into the<br />
VM102-SECURE by triggering the sensor the VM102-SECURE will respond with<br />
“BING – BING – BBRRRR” invalid tone.<br />
��Programming Encrypted Radio Keys: With “READY” flashing on the display of the<br />
VM102-SECURE, press and hold the PANIC button. This sequence takes<br />
approximately 8 seconds. The VM102-SECURE will respond with a “BING” when the<br />
panic message is received, then “BING-BING - BING-BING." The VM102-SECURE will<br />
flash the key number programmed (eg. “KEY 2”).<br />
��Programming Supervised / Encrypted Reed switches With “READY” flashing on the<br />
display of the VM102-SECURE, connect the correct lithium battery to the reed switch.<br />
The VM102-SECURE will respond “BING-BING - BING-BING." The display will flash<br />
the sensor number programmed (eg. “SENS 2”). If you try to program the sensor into<br />
the VM102-SECURE by triggering the reed switch, the VM102-SECURE will respond<br />
with “BING – BING – BBRRRR” invalid tone.<br />
��Programming Supervised Panic Buttons: With “READY” flashing on the display of the<br />
VM102-SECURE, connect the correct lithium battery to the panic button. The VM102-<br />
SECURE will respond with “BING-BING - BING-BING." The display will flash the key<br />
number programmed (eg. “KEY 6”). If you try to program the panic button or door bell<br />
into the VM102-SECURE by pressing the front button, the VM102-SECURE will<br />
respond with “BING – BING – BBRRRR” invalid tone.<br />
NOTE: Panic buttons are recognised as KEYS.<br />
��Programming Door Bells: With “READY” flashing on the display of the VM102-<br />
SECURE, press and hold the BELL button. This sequence takes approximately 6<br />
seconds, The VM102-SECURE will respond with a “BING” when the Bell message is<br />
received then “BING-BING - BING-BING." The VM102-SECURE will flash the door bell<br />
number programmed (eg. “KEY 7”).<br />
NOTE: Door bells are recognised as KEYS.<br />
72