Installation

Recommendations

Info

OPEN OPEN/CLOSE REPORTS (default = OFF) Open/close reports are messages sent to the monitoring station each time the system is ARMED or DISARMED, including which user (user ID) operated the system. ON Enabled OFF Disabled LOWBAT LOW BATTERY REPORTING (default = NONE) NONE No low battery reporting MAIN Report low main battery SENSOR Report low detector batteries ALL Report low main and detector batteries CLIENT CLIENT ACCOUNT NUMBER (default = 0000) 30 days after exiting PROGRAM mode, this option becomes hidden in local PROGRAM mode and can only be reprogrammed via remote up/download. ��Press "ON" to view programmed client account number. The first digit will flash. ��Press "ON" to step through values for the first digit (0-9,B,C,D,E,F). ��Press PANIC to store the digit. The second digit will now flash. ��Repeat for remaining digits. ��Press PANIC to store last digit, and first digit will flash. ��Repeat programming procedure to make corrections, or press "OFF" to return to top level. 0000 - 9999 Client Account number PHONE1 PHONE NUMBER 1 (default = -) NOTE: Dialler function is enabled when PHONE1 is programmed (i.e. not ‘-’). Up to 20 digits can be programmed. 30 days after exiting PROGRAM mode, this option becomes hidden in local PROGRAM mode and can only be reprogrammed via remote up/download. ��Press "ON" to view programmed phone number, which will scroll across the display, after which 2 beeps will occur and the first digit will be flashing. - Press "OFF" to leave the number unchanged and step to the next option. - Press "ON" to step through values for the first digit: - PAUSE 0-9 digits 0-9 * STAR # HASH ��Press PANIC to store the first digit. The second digit will flash. ��Repeat for each digit (the display will scroll left after the fourth digit is entered). - Press "ON" to store the last digit, then press "OFF". - The programmed phone number will scroll across the display, after which 2 beeps will occur and the first digit will be flashing. ��Press "OFF" to step to next option, or repeat procedure to make corrections. 63
PHONE2 PHONE NUMBER 2 (default = -) The procedure is the same as for PHONE NUMBER 1. ABORT DIALLER ABORT DELAY (default = 15) Gives the opportunity to abort sending an alarm message to the monitoring station within the programmed time (i.e. cancel a false alarm). 0-60 Time in seconds, 5 second steps MEDIC MEDICAL KEY ABORT DELAY (default = 20) Gives the opportunity to abort sending a Medical alarm message to the monitoring station within the programmed time (i.e. cancel a false alarm). 0-60 Time in seconds, 5 second steps T-CALL DIALLER TEST CALL (default = 7) If enabled, the first test call is sent 14 hours after PROGRAM mode EXIT. OFF Test calls disabled 1,7,14,30 Test call period in days DEFALT RESET TO FACTORY DEFAULTS Erase devices and/or default options as required. PHONE1, PHONE2 and CLIENT will only be cleared if programming timeout has not disabled reprogramming of these options. VM102-Secure will jump to the start of PROGRAM mode, displaying KEY 1. ALL Erases all programmed devices and defaults all options OPTION Defaults all option values KEY Erases all keys SENSOR Erases all detectors; defaults SENSOR 1 (main PIR) P-EXIT PROGRAM MODE EXIT/CONTINUE ��Press "ON" to exit PROGRAM mode. ��Press "OFF" to step to first program option. ��If the "OFF" button is pressed, LEARN will be displayed. By then pressing "ON", READY will be flash and the unit will be ready to learn a new code (radio key or device) 64
Page 1 and 2:
HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4:
INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6:
VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8:
LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10:
AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12:
AM AERIAL The coaxial cable supplie
Page 13 and 14:
BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16:
INSTALLATION OF MASTER STATION TIMB
Page 17 and 18: Mounting Brackets for Tamper Switch
Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34: Operating Automatic Gates AUTO GATE
Page 35 and 36: 4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
Page 53 and 54: Home Press the "ON" button two time
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67: LOKOUT DETECTOR LOCKOUT (default =
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76: Category When Chirp and/or Voice re
Page 77 and 78: IMPORTANT NOTES: To place the VM102
Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84: CHANGING THE CHIME The chime melody
Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
Page 87 and 88: CHANGING THE CHIME The chime melody
Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94: AUX ��Outputs specific voltage
Page 95: TROUBLE SHOOTING Fault: Volume Cont
show all

Installation

Create successful ePaper yourself

Delete template?

Save as template?