Installation
Installation Installation
SIGNAL SIGNAL CHECK: Check signal strength of radio detectors and keys VM102-Secure registers the first device received and displays the signal strength (1-9), and beeps a corresponding number of times. ��Press "ON" to activate Signal Check - display shows “SEND DEVICE” ��For a key, press PANIC; for a detector, activate the detector ��Listen to beeps, view display ��Press "OFF" to exit Signal Check ��Press "ON" to re-activate Signal Check -- No detectors received SENS 2-23 Detector x received KEY 1-23 Key x received 1-9 Signal strength RADJAM RADIO JAMMING (default = OFF) In the event of a VM102-Secure sensing a continuous (>30 secs) source of Radio Frequency Interference (RFI), it can generate a CHIME alarm in DISARMED, HOME or HOME 2 modes, and a full alarm in ARMED mode. ON Enabled OFF Disabled RADSUB RADIO INTENTIONAL MESSAGE SUBSTITUTION (default = OFF) In the event of a VM102-Secure sensing a radio message with a recognised device ID but failing decryption, it can generate a CHIME alarm in DISARMED, HOME or HOME 2 modes, and a full alarm in ARMED mode. ON Enabled OFF Disabled SUPVIS SUPERVISION STATUS (default = 8) Non-supervised devices: If enabled, a system alarm will occur if the detector has not triggered for 20 ARM/DISARM operations. The count starts after the device’s first transmission following PROGRAM mode exit. If the warning is ignored, the display will Supervised devices: If enabled, a system alarm will occur if a valid supervisory message has not been received from the detector within the period set in this option. Supervised devices send a poll message every hour (with a random offset factor of +/- 2 minutes to eliminate collisions). If the main system does not receive a signal for X consecutive hours, a warning will be displayed. 1,4,8,16,24 Supervision alarm occurs if no supervisory message is received within set period (in hours) OFF Supervision alarms disabled 61
LOKOUT DETECTOR LOCKOUT (default = OFF) If DETECTOR LOCKOUT is enabled, all devices will only sound the external siren the first time they alarm. Any subsequent alarms from these detectors will only sound the internal siren and flash the strobe. ON Enabled OFF Disabled ENTRY ENTRY DELAY TIME (default = 10) 5-30 Time in seconds; values in 5 second steps EXIT EXIT DELAY TIME (default = 5) 5-60 Time in seconds; values in 5 second steps SIREN SIREN RESET TIME (default = 5) 1, 2, 5 Reset time in minutes CHIRPS EXTERNAL SIREN CHIRPS (default = ON) External siren chirps on ARM and DISARM. External siren does not chirp when activating or deactivating HOME or HOME 2 modes, when this option is enabled. ON Enabled OFF Disabled V-ARM VOICE ANNUNCIATION ARM/DISARM (default = ON) OFF Armed and disarmed events not annunciated ON Armed and disarmed events annunciated V-ALRM VOICE ANNUNCIATION ALARM (default = ON) OFF Alarm events not annunciated ON Alarm events annunciated V-BATT VOICE ANNUNCIATION LOW BATTERY (default = ON) OFF Low battery events not annunciated ON Low battery events annunciated V-FALT VOICE ANNUNCIATION FAULT (default = ON) OFF System faults not annunciated ON System faults annunciated V-DEMO VOICE ANNUNCIATION DEMO (default = OFF) OFF Sales presentation not annunciated ON Sales presentation annunciated 62
- Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
- Page 17 and 18: Mounting Brackets for Tamper Switch
- Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
- Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
- Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
- Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
- Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
- Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
- Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
- Page 33 and 34: Operating Automatic Gates AUTO GATE
- Page 35 and 36: 4-Wire Operation If only four wires
- Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
- Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
- Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
- Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
- Page 45 and 46: POWERING UP THE SYSTEM For the VM10
- Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
- Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
- Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
- Page 53 and 54: Home Press the "ON" button two time
- Page 55 and 56: KEY TYPES User Key ��3-button p
- Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
- Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
- Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
- Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
- Page 65: SENS 2-23 DETECTOR 2-23 (default =
- Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
- Page 71 and 72: Main Unit The following events are
- Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
- Page 75 and 76: Category When Chirp and/or Voice re
- Page 77 and 78: IMPORTANT NOTES: To place the VM102
- Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
- Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
- Page 83 and 84: CHANGING THE CHIME The chime melody
- Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
- Page 87 and 88: CHANGING THE CHIME The chime melody
- Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
- Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
- Page 93 and 94: AUX ��Outputs specific voltage
- Page 95: TROUBLE SHOOTING Fault: Volume Cont
LOKOUT DETECTOR LOCKOUT (default = OFF)<br />
If DETECTOR LOCKOUT is enabled, all devices will only sound the external siren the first<br />
time they alarm. Any subsequent alarms from these detectors will only sound the internal<br />
siren and flash the strobe.<br />
ON Enabled<br />
OFF Disabled<br />
ENTRY ENTRY DELAY TIME (default = 10)<br />
5-30 Time in seconds; values in 5 second steps<br />
EXIT EXIT DELAY TIME (default = 5)<br />
5-60 Time in seconds; values in 5 second steps<br />
SIREN SIREN RESET TIME (default = 5)<br />
1, 2, 5 Reset time in minutes<br />
CHIRPS EXTERNAL SIREN CHIRPS (default = ON)<br />
External siren chirps on ARM and DISARM. External siren does not chirp when activating<br />
or deactivating HOME or HOME 2 modes, when this option is enabled.<br />
ON Enabled<br />
OFF Disabled<br />
V-ARM VOICE ANNUNCIATION ARM/DISARM (default = ON)<br />
OFF Armed and disarmed events not annunciated<br />
ON Armed and disarmed events annunciated<br />
V-ALRM VOICE ANNUNCIATION ALARM (default = ON)<br />
OFF Alarm events not annunciated<br />
ON Alarm events annunciated<br />
V-BATT VOICE ANNUNCIATION LOW BATTERY (default = ON)<br />
OFF Low battery events not annunciated<br />
ON Low battery events annunciated<br />
V-FALT VOICE ANNUNCIATION FAULT (default = ON)<br />
OFF System faults not annunciated<br />
ON System faults annunciated<br />
V-DEMO VOICE ANNUNCIATION DEMO (default = OFF)<br />
OFF Sales presentation not annunciated<br />
ON Sales presentation annunciated<br />
62