Installation
Installation Installation
Alarms VM102-SECURE places alarm events for transmission to the Radio Dialler on a queue. When it transmits, it transmits the next message on the queue. If an "acknowledge" is not received from the Dialler, the VM102-SECURE re-transmits the message for a total of 10 attempts. If still unsuccessful, the VM102-SECURE ceases transmitting until a new event occurs and raises a system alarm. The oldest messages on the queue are sent first. If the queue is full (10 messages), a new message will overwrite the oldest message. Dialler Status Dialler status is sent to the VM102-SECURE when a condition changes, and VM102- SECURE raises a system alarm as required. PROGRAMMING OPTIONS KEY 1-23 KEY 1-23 (default = KEY) KEY USER KEY Alarm system user key DURESS DURESS User key with PANIC button programmed for “DURESS” operation MEDIC MEDICAL Medical help key (behaves like Duress alarm) BELL DOORBELL Doorbell NO PAN NO PANIC Stops the PANIC button from operating ERASE ERASE Remove previously programmed key SENS 1 DETECTOR 1 (main unit detector, permanently allocated; default = ALARM) ALARM ALARM Active when ARMED, inactive when DISARMED HOME HOME Active when ARMED or HOME modes HOME 2 HOME 2 Active when ARMED and HOME 2 modes FIRE FIRE 24 hour alarm, always active CHIME CHIME Chime* when DISARMED, inactive when ARMED, HOME or HOME 2 modes ACHIME ALARM/CHIME Alarm when ARMED, chime** when DISARMED, inactive when in HOME or HOME 2 modes HCHIME HOME/CHIME Alarm when ARMED mode, chime** when in HOME or HOME 2 modes, inactive when DISARMED H2CHIM HOME 2 CHIME Alarm when ARMED mode, chime** when in HOME or HOME 2 modes, inactive when DISARMED EXCLUD EXCLUDE Detector is excluded (*) Chime tone (**) Warning tone 59
SENS 2-23 DETECTOR 2-23 (default = ALARM) To learn a new detector: With display showing "LEARN" For encrypted restoring detector (e.g. reed switch): ��Power the detector off and back on again, by momentarily disconnecting the battery, with the reed switch "closed," to enable "CHECK mode" operation, and the reed "open" to disable "CHECK mode" operation. The VM102-Secure gives 2 beeps and flashes "SENS 2-23" when the code is accepted. For encrypted non-restoring detector: ��Power the detector off and back on again by momentarily disconnecting the battery. The VM102-Secure gives 2 beeps and flashes "SENS 2-23" when the code is accepted. ALARM ALARM Active when ARMED, inactive when DISARMED HOME HOME Active when ARMED or HOME modes HOME 2 HOME 2 Active when ARMED & HOME 2 modes FIRE FIRE 24 hour alarm, always active. CHIME CHIME Chime* when DISARMED, inactive when ARMED, HOME or HOME 2 modes ACHIME ALARM/CHIME Alarm when ARMED, chime** when DISARMED, inactive when in HOME or HOME 2 modes HCHIME HOME/CHIME Alarm when ARMED mode, chime** when in HOME or HOME 2 modes, inactive when DISARMED H2CHIM HOME 2 CHIME Alarm when ARMED mode, chime** when in HOME or HOME 2 modes, inactive when DISARMED ERASE ERASE Detector is erased (*) Chime tone (**) Warning tone RANGE DETECTOR RANGE (default = LOW) LOW Low range 8m HIGH High range 14m NOTE: OK light turns on each time PIR is activated. PULSE DETECTOR PULSE COUNT (default = 3) 1-4 Number of times (1-4) a detection beam needs to crossed before an alarm occurs NOTE: OK light turns on each time PIR is activated. 60
- Page 13 and 14: BLOCK DIAGRAM FOR SYSTEM WITH MASTE
- Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
- Page 17 and 18: Mounting Brackets for Tamper Switch
- Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
- Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
- Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
- Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
- Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
- Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
- Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
- Page 33 and 34: Operating Automatic Gates AUTO GATE
- Page 35 and 36: 4-Wire Operation If only four wires
- Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
- Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
- Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
- Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
- Page 45 and 46: POWERING UP THE SYSTEM For the VM10
- Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
- Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
- Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
- Page 53 and 54: Home Press the "ON" button two time
- Page 55 and 56: KEY TYPES User Key ��3-button p
- Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
- Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
- Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
- Page 63: PROGRAMMING RADIO DIALLER Local Pro
- Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
- Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
- Page 71 and 72: Main Unit The following events are
- Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
- Page 75 and 76: Category When Chirp and/or Voice re
- Page 77 and 78: IMPORTANT NOTES: To place the VM102
- Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
- Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
- Page 83 and 84: CHANGING THE CHIME The chime melody
- Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
- Page 87 and 88: CHANGING THE CHIME The chime melody
- Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
- Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
- Page 93 and 94: AUX ��Outputs specific voltage
- Page 95: TROUBLE SHOOTING Fault: Volume Cont
Alarms<br />
VM102-SECURE places alarm events for transmission to the Radio Dialler on a queue.<br />
When it transmits, it transmits the next message on the queue. If an "acknowledge" is not<br />
received from the Dialler, the VM102-SECURE re-transmits the message for a total of 10<br />
attempts. If still unsuccessful, the VM102-SECURE ceases transmitting until a new event<br />
occurs and raises a system alarm.<br />
The oldest messages on the queue are sent first. If the queue is full (10 messages), a new<br />
message will overwrite the oldest message.<br />
Dialler Status<br />
Dialler status is sent to the VM102-SECURE when a condition changes, and VM102-<br />
SECURE raises a system alarm as required.<br />
PROGRAMMING OPTIONS<br />
KEY 1-23 KEY 1-23 (default = KEY)<br />
KEY USER KEY Alarm system user key<br />
DURESS DURESS User key with PANIC button programmed for “DURESS”<br />
operation<br />
MEDIC MEDICAL Medical help key (behaves like Duress alarm)<br />
BELL DOORBELL Doorbell<br />
NO PAN NO PANIC Stops the PANIC button from operating<br />
ERASE ERASE Remove previously programmed key<br />
SENS 1 DETECTOR 1 (main unit detector, permanently allocated; default = ALARM)<br />
ALARM ALARM Active when ARMED, inactive when DISARMED<br />
HOME HOME Active when ARMED or HOME modes<br />
HOME 2 HOME 2 Active when ARMED and HOME 2 modes<br />
FIRE FIRE 24 hour alarm, always active<br />
CHIME CHIME Chime* when DISARMED, inactive when ARMED, HOME<br />
or HOME 2 modes<br />
ACHIME ALARM/CHIME Alarm when ARMED, chime** when DISARMED, inactive<br />
when in HOME or HOME 2 modes<br />
HCHIME HOME/CHIME Alarm when ARMED mode, chime** when in HOME or<br />
HOME 2 modes, inactive when DISARMED<br />
H2CHIM HOME 2 CHIME Alarm when ARMED mode, chime** when in HOME<br />
or HOME 2 modes, inactive when DISARMED<br />
EXCLUD EXCLUDE Detector is excluded<br />
(*) Chime tone<br />
(**) Warning tone<br />
59