Installation

Recommendations

Info

ENTRY & EXIT DELAY EXIT DELAY is the time, between pressing the "ON" button and the system being ARMED, during which detector activations are ignored. The siren will chirp once when the "ON" button is pressed to indicate the start of EXIT DELAY and chirp once at the end of exit delay to indicate the system being ARMED. A warning tone at the end of EXIT DELAY indicates an unsealed reed switch, specified as displayed. ENTRY DELAY is the time between the activation a detector and the system being DISARMED, during which, detector activations do not cause an alarm. During ENTRY DELAY the siren will chirp once a second. When the "OFF" button is pressed the siren chirps 3 times to indicate DISARMED. If the "OFF" button is not pressed within the ENTRY DELAY, the siren sounds and strobe flashes. ABORT DELAY When an alarm event occurs, the siren sounds when ENTRY DELAY expires. The alarm is sent to the monitoring station only after ABORT DELAY expires. ABORT DELAY commences immediately after ENTRY DELAY expires. This gives the user time to abort the sending of an accidental alarm by pressing the "OFF" button within the ABORT DELAY period. ABORT DELAY is a programmable option. If ABORT DELAY is programmed to 0, then an alarm will be sent at the expiry of ENTRY DELAY, i.e. user CANCEL cannot be sent. If the "OFF" button is pressed before ABORT DELAY expires, a user CANCEL message will be sent. (CANCEL is a non-actionable event for the monitoring station, but it makes the monitoring station aware that the system had been briefly triggered before a user cancel.) LOCKOUT Alarm lockout inhibits multiple activation’s of the same alarm (excluding panic) i.e. the external siren will not sound again until the "OFF" button is pressed (alarm cleared). The internal siren will always sound if the option is OFF. If the option is "ON" both the external and internal sirens will be locked out (as required by AS2201.1) RUNAWAY Runaway limits the number of times an alarm from a particular device will be sent to the monitoring station. After 3 alarms have been sent, no further alarms for that device will be sent to the central station until the system is DISARMED and ARMED again. This feature prevents a large customer phone bill being incurred if, for example, a door protected by a reed switch is left unlatched and swings open and shut many times. Runaway is permanently enabled. 55
PROGRAMMING VM102-SECURE uses a common “LEARN” mode to listen for programming messages from new devices. The installer does not specify a slot number instead the unit allocates the next available slot when a device is accepted. Learning New Devices 1. On the VM102-Secure Master, remove and replace the 2-way shunt on the security PCB. 2. The software revision number is displayed briefly. 3. If unit has no keys programmed, it will display LEARN / KEY 1 until a key is programmed, otherwise the unit flashes LEARN and waits 10 seconds to receive a radio key message: ��If "OFF" is pressed on a programmed key, the unit enters PROGRAM mode, displaying the first programmed key. ��If "ON" is pressed on a programmed key, the unit enters PROGRAM mode, flashing READY and listening for a LEARN message from a new device (key or detector). ��If a LEARN message is received from an unprogrammed key, the unit will add the key to the next available slot and display the new slot number, then allow the user to configure the new key. ��If none of the above occur after 10 seconds, the unit enters OPERATE mode. (This is only the case if there is at least one radio key already programmed.) 4. To cause a device to send a LEARN message: Device Mode Learn Procedure Key Encrypted Hold down PANIC button for approximately 8 seconds. Sensor Encrypted Disconnect and reconnect battery. If the device is successfully programmed, VM102-Secure will give a "BEEP, BEEP, BEEP, BEEP." The unit will add the new device to the next available slot, display the new slot number, and allow the user to configure the new device. If the key or device is already programmed an error sound "BBRRRR" will occur. This also applies if the method of programming an encrypted key or device is incorrect. For example, if you try programming in an encrypted key by pressing the "OFF" button three times, the error sound "BBRRRR" will be heard. Press "OFF" to return to LEARN. Press "ON" to flash READY and learn another device. Or press "OFF" to step through devices and program options. 56
Page 1 and 2:
HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4:
INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6:
VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8:
LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10: AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12: AM AERIAL The coaxial cable supplie
Page 13 and 14: BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
Page 17 and 18: Mounting Brackets for Tamper Switch
Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34: Operating Automatic Gates AUTO GATE
Page 35 and 36: 4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
Page 53 and 54: Home Press the "ON" button two time
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59: DIALER < RADIO < FAIL DIALER < POWE
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76: Category When Chirp and/or Voice re
Page 77 and 78: IMPORTANT NOTES: To place the VM102
Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84: CHANGING THE CHIME The chime melody
Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
Page 87 and 88: CHANGING THE CHIME The chime melody
Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94: AUX ��Outputs specific voltage
Page 95: TROUBLE SHOOTING Fault: Volume Cont
show all

Installation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?