Installation

Recommendations

Info

START UP VM102-Secure restarts by powering down and powering up the system (including battery), by removing and refitting the shunt on the back of the security PCB, or by a system reset caused by possible electrical interference. When the unit is restarted it briefly allows entry into PROGRAM mode (refer to section “PROGRAMMING”). Following this, the unit enters the previous operational mode. If the unit was in ARMED, HOME, or HOME 2 mode, it will show the mode on the display for 30 seconds. During this period triggers from the main PIR are ignored, allowing it time to settle. After this, the unit resumes normal operation in the mode displayed. This process will occur silently, without the usual arming sounds. USER MODES The system can be in one of four user modes, DISARMED, HOME, HOME 2 and ARMED. From the DISARMED mode, pressing "ON" enters ARMED mode, a second "ON" press enters HOME mode, and a third "ON" press enters HOME 2 mode (provided devices are programmed for these modes), as detailed in the following sections. Armed Press "ON" button once to ARM the system. Display ARMED Display for exit delay duration OK Light ON Voice “Armed” If V-ARM option enabled Siren 1 chirp internal at start of exit delay (if V-ARM option disabled), and 1 chirp at end of exit delay 1 chirp external (if enabled) at start of exit delay Strobe flash for 2 seconds When the display extinguishes, the system is fully armed. An optional exit delay may be programmed if desired. 47
Home Press the "ON" button two times (less than 4 second interval) to enter HOME mode. When the display extinguishes, the system is armed in HOME mode. HOME mode may only be entered if the HOME mode function has been programmed, and the VM102-Secure is DISARMED. Display HOME Display for exit delay duration OK Light Single "OFF" flash once every 2 seconds Indicates that VM102-Secure is in HOME mode Voice “Home” If V-ARM option enabled Siren Internal: HOME arming tone Strobe flash for 5 seconds Home 2 If V-ARM option disabled Press the "ON" button three times (successive presses with intervals of less than 4 seconds) to enter HOME 2 mode. When the display extinguishes, the system is armed in HOME 2 mode. HOME 2 mode may only be entered if the HOME 2 function has been programmed and the VM102-Secure is DISARMED. Display HOME 2 Display for exit delay duration OK Light Double "OFF" flash every 2 seconds Indicates that VM102-Secure is in HOME 2 mode Voice “Home two” If V-ARM option enabled Siren Internal: HOME 2 arming tone Strobe flash for 5 seconds If V-ARM option disabled 48
Page 1 and 2: HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4: INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6: VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8: LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10: AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12: AM AERIAL The coaxial cable supplie
Page 13 and 14: BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
Page 17 and 18: Mounting Brackets for Tamper Switch
Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34: Operating Automatic Gates AUTO GATE
Page 35 and 36: 4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
Page 51: PROGRAMMING SECURITY FEATURES (DETA
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76: Category When Chirp and/or Voice re
Page 77 and 78: IMPORTANT NOTES: To place the VM102
Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84: CHANGING THE CHIME The chime melody
Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
Page 87 and 88: CHANGING THE CHIME The chime melody
Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94: AUX ��Outputs specific voltage
Page 95: TROUBLE SHOOTING Fault: Volume Cont

Installation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?