Installation

Recommendations

Info

PROGRAMMING SECURITY FEATURES (QUICK GUIDE) 1) Fit 2-way jumper to alarm PCB to enter “LEARN” mode. 2) Version number followed by alternating “LEARN” and “KEY 1” will appear on display. 3) Press and hold “PANIC” button on remote key fob. 4) A single bell followed by two double bells will be heard. 5) “KEY 1” will flash on display. 6) Press “DISARM” button on key fob to select “LEARN.” 7) Press “ARM” button on key fob to select “READY.” 8) Press and hold “PANIC” button on 2nd key fob. 9) A single bell followed by two double bells will be heard. 10) “KEY 2” will flash on display. 11) Press “DISARM” button on key fob to select “LEARN.” 12) Press “ARM” button on key fob to select “READY.” 13) Select “LEARN” and “READY” modes with key fob as above, to program additional key fobs. 14) These will appear as “KEY 3”, “KEY 4”, etc. 15) To program sensors, connect battery to sensor while Master is in “READY” mode. 16) Select “LEARN” and “READY” modes with key fob as above to program additional wireless sensors. 17) These will appear as “SENS 1”, “SENS 2” etc. 18) Press “DISARM” button repeatedly to scroll through the various options for programming. 19) Press “ARM” button to view current setting. 20) Repeatedly press “ARM” button to view optional settings. 21) Press and hold “PANIC” button to select new setting. 22) Use “DISARM” button to scroll through remaining options. 23) When “P-EXIT” appears on display, Press “ARM” button to exit program mode. 24) Voice message will be heard: “Warning outside siren tamper fault." Display will read: “Siren tamper excluded XX hrs XX min ago.” This is because the tamper switch on the fascia is unsealed. 25) Press the “DISARM” button on the key fob to clear message. 26) Press and release the Lid tamper switch to test tamper circuit. Siren should sound from Master and message should scroll across display. 27) Press the "DISARM" button on the key fob repeatedly until message clears. 28) While arming and disarming using remote key fob, adjust VR1 on Master termination PCB to set the security voice volume level. NOTE: This adjustment will also affect the siren volume level from the Master and Room Stations and should be set as loud as tolerable. 45
PROGRAMMING SECURITY FEATURES (DETAILED) FEATURES VM102-SECURE includes the following features and functions: ��23 supervised and encrypted radio devices (minimum 1 key and 1 detector) ��6 character Display ��Voice annunciation ��Two HOME modes ��Variable voice volume ��Strobe light differentiation for arm and disarm ��Doorbell ��Fixed panic button (supervised) ��Event memory (locally accessible) DEVICE CATEGORIES There are two categories of devices: 1. Keys (devices operated by buttons) User key Medical key Doorbell Fixed Panic button 2. Detectors PIR Reed switch DEVICE ALLOCATION The allowable number of keys is 1-23, denoted as KEY 1-23. The allowable number of detectors is 1-23, denoted as SENSOR 1-23. The maximum allowable number of keys and detectors is 24, e.g. 4 keys and 20 detectors. There are a total of 24 device slots. KEY 1 must be programmed first, with a radio key device. SENSOR 1 is non-applicable. The remaining slots can be programmed with any combination of radio devices. 46
Page 1 and 2: HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4: INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6: VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8: LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10: AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12: AM AERIAL The coaxial cable supplie
Page 13 and 14: BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
Page 17 and 18: Mounting Brackets for Tamper Switch
Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34: Operating Automatic Gates AUTO GATE
Page 35 and 36: 4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49: VM102 MASTER STATION ADJUSTMENTS SE
Page 53 and 54: Home Press the "ON" button two time
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76: Category When Chirp and/or Voice re
Page 77 and 78: IMPORTANT NOTES: To place the VM102
Page 79 and 80: VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82: VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84: CHANGING THE CHIME The chime melody
Page 85 and 86: WIRING VOLTAGE OUTPUTS The Lock out
Page 87 and 88: CHANGING THE CHIME The chime melody
Page 89 and 90: SETTING UP INPUT JACK TYPE B If the
Page 91 and 92: SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94: AUX ��Outputs specific voltage
Page 95: TROUBLE SHOOTING Fault: Volume Cont

Installation

Create successful ePaper yourself

Delete template?

Save as template?