Installation

Recommendations

Info

INSTALLATION OF VF103 DOOR STATIONS These stations are best located adjacent to the front door or at the front gate at a suggested height of 1400 millimetres and may require a wall box depending upon the surface to which they are to be affixed. Any station exposed to the weather will require the fitting of a weatherproof cover. Where stations are to be installed in solid brick or concrete columns at a front gate, it is required that the cable be run in conduit from the station to below ground level and back to the house. When using 8-wire cable to connect to the Door Station, do not connect the spare two wires to the MUS1/MUS2 terminals at the Master Station (or Room Station) end of the cable. The two spare wires from an 8-wire cable may be wired in parallel to the POS and NEG wires to the gate station, to double the maximum cable distance to a length of 200 metres. Where a Door Station is part of a wiring loop, the Door Station should generally be the last station on the loop. BRICK REMOVED INSERT WALL BOX INTO OPENING WOOD FIXING SCREW (26mm) DOOR STATION – BRICK WALL WALL BOX BACK HOUSING WOOD FIXING SCREW (26mm) FASCIA 23
CABLE TERMINATION FOR VF 103 DOOR STATION Using Valet Cable LK - + CH - COM2 COM1 SHLD VLC TC NEG POS BLUE WHITE OUTER SHIELD SHIELDED WHITE SHIELDED RED BLACK RED RELAY RELAY GREEN ORANGE CABLE TERMINATION FOR VF103 DOOR STATION Using Cat 5 Cable LK - + CH - COM2 COM1 SHLD VLC TC NEG POS GREEN/WH GREEN BLUE/WH BLUE BROWN/WH BROWN RELAY RELAY ORANGE ORANGE/WH NOT USED VALET CABLE NOT USED CAT 5 CABLE CONNECTION AT ROOM OR MASTER CONNECTION AT ROOM OR MASTER GREEN ORANGE ORANGE ORANGE/WH 24
Page 1 and 2: HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4: INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6: VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8: LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10: AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12: AM AERIAL The coaxial cable supplie
Page 13 and 14: BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
Page 17 and 18: Mounting Brackets for Tamper Switch
Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23 and 24: INSTALLATION OF VR102 ROOM STATIONS
Page 25 and 26: CABLE TERMINATION FOR VR102 ROOM ST
Page 27: CABLE TERMINATION FOR VR102 ROOM ST
Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34: Operating Automatic Gates AUTO GATE
Page 35 and 36: 4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
Page 53 and 54: Home Press the "ON" button two time
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76: Category When Chirp and/or Voice re
Page 77 and 78: IMPORTANT NOTES: To place the VM102
Page 79 and 80:
VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82:
VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84:
CHANGING THE CHIME The chime melody
Page 85 and 86:
WIRING VOLTAGE OUTPUTS The Lock out
Page 87 and 88:
CHANGING THE CHIME The chime melody
Page 89 and 90:
SETTING UP INPUT JACK TYPE B If the
Page 91 and 92:
SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94:
AUX ��Outputs specific voltage
Page 95:
TROUBLE SHOOTING Fault: Volume Cont
show all

Installation

Create successful ePaper yourself

Delete template?

Save as template?