Installation

Recommendations

Info

ROOM STATIONS IN CAVITY BRICK WALLS Remove the brick and mortar and insert the wall box, ensuring that all cables are first pulled through the holes in the rear of the wall box. <strong>Installation</strong> is then the same as for timber frame walls except for using another wood screw instead of the wing toggle bolt. BRICK REMOVED LOAD RESISTOR Insert Wall Box into opening Wood Fixing Screw (26mm) ROOM STATION - CAVITYBRICK WALL WALL BOX ROOM STATION HOUSING Wood Fixing Screw (26mm) 4 x Facia Fixing Screws (12mm) ROOM STATION FACIA For Room Station Only systems (Systems without a Master), a load resistor must be fitted across the VLC and NEG terminals of the station to which the power supply is connected. Although a 220K resistor is supplied with each Room Station, only one of these resistors is to be fitted to a Room Station Only system. When fitting a load resistor to a Room Station, take care that the legs of the resistor do not short against the speaker when the fascia is attached to the back case. Because Master Stations have a Load Resistor built in to the circuitry, the fitting of an external Load resistor is generally not required for Master systems. 19
CABLE TERMINATION FOR VR102 ROOM STATION Valet Cable - Without Auxiliary Output Board AUX MUS2 MUS1 COM2 COM1 SHLD VLC TC NEG POS ORANGE GREEN BLUE WHITE OUTER SHIELD SHIELDED WHITE SHIELDED RED BLACK RED CABLE TERMINATION FOR VR102 ROOM STATION Valet Cable - With Auxiliary Output Board AUX MUS2 MUS1 COM2 COM1 SHLD VLC TC NEG POS SHIELDED RED ORANGE GREEN BLUE WHITE OUTER SHIELD SHIELDED WHITE BLACK RED VALET CABLE VALET CABLE SINGLE HOOK-UP WIRE (13 X 0.13 OR SIMILAR) 20
Page 1 and 2: HOME COMMUNICATION EQUIPMENT SYSTEM
Page 3 and 4: INSTALLATION OF VF103 DOOR STATIONS
Page 5 and 6: VR102 ROOM STATION ADJUSTMENTS.....
Page 7 and 8: LOCATION OF EQUIPMENT MASTER STATIO
Page 9 and 10: AUXILIARY/LOCK OUTPUT BOARD The Aux
Page 11 and 12: AM AERIAL The coaxial cable supplie
Page 13 and 14: BLOCK DIAGRAM FOR SYSTEM WITH MASTE
Page 15 and 16: INSTALLATION OF MASTER STATION TIMB
Page 17 and 18: Mounting Brackets for Tamper Switch
Page 19 and 20: CABLE TERMINATIONS FOR VM102-S MAST
Page 21 and 22: FM AM POWER SUPPLY 13.8V BATT IP NE
Page 23: INSTALLATION OF VR102 ROOM STATIONS
Page 27 and 28: CABLE TERMINATION FOR VR102 ROOM ST
Page 29 and 30: CABLE TERMINATION FOR VF 103 DOOR S
Page 31 and 32: WIRING VOLTAGE OUTPUTS The Lock out
Page 33 and 34: Operating Automatic Gates AUTO GATE
Page 35 and 36: 4-Wire Operation If only four wires
Page 37 and 38: CABLE TERMINATION FOR VF102 DOOR ST
Page 39 and 40: INSTALLATION OF AUXILIARY INPUT JAC
Page 41 and 42: INSTALLATION OF WIRELESS AUDIO TRAN
Page 43 and 44: INSTALLATION OF POWER SUPPLY A regu
Page 45 and 46: POWERING UP THE SYSTEM For the VM10
Page 47 and 48: VM102 MASTER STATION PROGRAMMING To
Page 49 and 50: VM102 MASTER STATION ADJUSTMENTS SE
Page 51 and 52: PROGRAMMING SECURITY FEATURES (DETA
Page 53 and 54: Home Press the "ON" button two time
Page 55 and 56: KEY TYPES User Key ��3-button p
Page 57 and 58: DISPLAY DESCRIPTION PANIC < KEY, BU
Page 59 and 60: DIALER < RADIO < FAIL DIALER < POWE
Page 61 and 62: PROGRAMMING VM102-SECURE uses a com
Page 63 and 64: PROGRAMMING RADIO DIALLER Local Pro
Page 65 and 66: SENS 2-23 DETECTOR 2-23 (default =
Page 67 and 68: LOKOUT DETECTOR LOCKOUT (default =
Page 69 and 70: PHONE2 PHONE NUMBER 2 (default = -)
Page 71 and 72: Main Unit The following events are
Page 73 and 74: VOICE MESSAGES & OPTIONS Voice annu
Page 75 and 76:
Category When Chirp and/or Voice re
Page 77 and 78:
IMPORTANT NOTES: To place the VM102
Page 79 and 80:
VR102 ROOM STATION PROGRAMMING To a
Page 81 and 82:
VR102 ROOM STATION ADJUSTMENTS MICR
Page 83 and 84:
CHANGING THE CHIME The chime melody
Page 85 and 86:
WIRING VOLTAGE OUTPUTS The Lock out
Page 87 and 88:
CHANGING THE CHIME The chime melody
Page 89 and 90:
SETTING UP INPUT JACK TYPE B If the
Page 91 and 92:
SYSTEM ONE - TERMINAL FUNCTIONS POS
Page 93 and 94:
AUX ��Outputs specific voltage
Page 95:
TROUBLE SHOOTING Fault: Volume Cont
show all

Installation

Create successful ePaper yourself

Delete template?

Save as template?