Automotive Electrical and Electronic Systems Classroom Manual Fifth Edition Update by John F. Kershaw
www.TechnicalBooksPDF.comTools, Fasteners, and Safety 17Figure 1-43. This vehicle fell from the hoist becausethe pads were not set correctly. No one was hurt, butthe vehicle was a total loss.(a)SAFETYARM CLIP(b)Figure 1-42. (a) Tall safety stands can be used toprovide additional support for a vehicle while on ahoist. (b) A block of wood should be used to avoid thepossibility of doing damage to components supportedby the stand.5. Before lowering the hoist, the safetylatch(es) must be released and the directionof the controls reversed. The speed downwardis often adjusted to be as slow as possiblefor additional safety.Figure 1-44. The safety arm clip should be engagedto prevent the possibility that the hoist support armscan move.ELECTRICAL CORDSAFETYUse correctly grounded three-prong sockets andextension cords to operate power tools. Sometools use only two-prong plugs. Make sure theseare double insulated. When not in use, keep electricalcords off the floor to prevent tripping overthem. Tape the cords down if they are placed inhigh foot traffic areas.
www.TechnicalBooksPDF.com(a)(b)Figure 1-45. (a) An assortment of hoist pad adapters that are often necessary to use tosafely hoist many pickup trucks, vans, and sport utility vehicles. (b) A view from underneatha Chevrolet pickup truck showing how the pad extensions are used to attach the hoist liftingpad to contact the frame.(a)(b)Figure 1-46. (a) In this photo the pad arm is just contacting the rocker panel of the vehicle.(b) This photo shows what can occur if the technician places the pad too far inward underneaththe vehicle. The arm of the hoist has dented in the rocker panel.18
- Page 2 and 3: www.TechnicalBooksPDF.comAutomotive
- Page 4 and 5: www.TechnicalBooksPDF.comIntroducti
- Page 6 and 7: www.TechnicalBooksPDF.comHow to Use
- Page 8 and 9: www.TechnicalBooksPDF.comAcknowledg
- Page 10 and 11: www.TechnicalBooksPDF.comContentsCh
- Page 12 and 13: www.TechnicalBooksPDF.comContentsxi
- Page 14 and 15: www.TechnicalBooksPDF.com1Tools,Fas
- Page 16 and 17: www.TechnicalBooksPDF.comTools, Fas
- Page 18 and 19: www.TechnicalBooksPDF.comTools, Fas
- Page 20 and 21: www.TechnicalBooksPDF.comFigure 1-1
- Page 22 and 23: www.TechnicalBooksPDF.comFigure 1-2
- Page 24 and 25: www.TechnicalBooksPDF.comTools, Fas
- Page 26 and 27: www.TechnicalBooksPDF.comTools, Fas
- Page 28 and 29: www.TechnicalBooksPDF.comTools, Fas
- Page 32 and 33: www.TechnicalBooksPDF.comTools, Fas
- Page 34 and 35: www.TechnicalBooksPDF.com2Introduct
- Page 36 and 37: www.TechnicalBooksPDF.comIntroducti
- Page 38 and 39: www.TechnicalBooksPDF.comIntroducti
- Page 40 and 41: www.TechnicalBooksPDF.comIntroducti
- Page 42 and 43: www.TechnicalBooksPDF.comIntroducti
- Page 44 and 45: www.TechnicalBooksPDF.comIntroducti
- Page 46 and 47: www.TechnicalBooksPDF.comIntroducti
- Page 48 and 49: www.TechnicalBooksPDF.com3Electrica
- Page 50 and 51: www.TechnicalBooksPDF.comElectrical
- Page 52 and 53: www.TechnicalBooksPDF.comElectrical
- Page 54 and 55: www.TechnicalBooksPDF.comElectrical
- Page 56 and 57: www.TechnicalBooksPDF.comElectrical
- Page 58 and 59: www.TechnicalBooksPDF.comElectrical
- Page 60 and 61: www.TechnicalBooksPDF.comElectrical
- Page 62 and 63: www.TechnicalBooksPDF.comElectrical
- Page 64 and 65: www.TechnicalBooksPDF.comElectrical
- Page 66 and 67: www.TechnicalBooksPDF.com4Magnetism
- Page 68 and 69: www.TechnicalBooksPDF.comMagnetism
- Page 70 and 71: www.TechnicalBooksPDF.comMagnetism
- Page 72 and 73: www.TechnicalBooksPDF.comMagnetism
- Page 74 and 75: www.TechnicalBooksPDF.comMagnetism
- Page 76 and 77: www.TechnicalBooksPDF.comMagnetism
- Page 78 and 79: www.TechnicalBooksPDF.comMagnetism
www.TechnicalBooksPDF.com
Tools, Fasteners, and Safety 17
Figure 1-43. This vehicle fell from the hoist because
the pads were not set correctly. No one was hurt, but
the vehicle was a total loss.
(a)
SAFETY
ARM CLIP
(b)
Figure 1-42. (a) Tall safety stands can be used to
provide additional support for a vehicle while on a
hoist. (b) A block of wood should be used to avoid the
possibility of doing damage to components supported
by the stand.
5. Before lowering the hoist, the safety
latch(es) must be released and the direction
of the controls reversed. The speed downward
is often adjusted to be as slow as possible
for additional safety.
Figure 1-44. The safety arm clip should be engaged
to prevent the possibility that the hoist support arms
can move.
ELECTRICAL CORD
SAFETY
Use correctly grounded three-prong sockets and
extension cords to operate power tools. Some
tools use only two-prong plugs. Make sure these
are double insulated. When not in use, keep electrical
cords off the floor to prevent tripping over
them. Tape the cords down if they are placed in
high foot traffic areas.