uhf tacsat /dama multi-service tactics, techniques ... - UHF-Satcom.com
uhf tacsat /dama multi-service tactics, techniques ... - UHF-Satcom.com
uhf tacsat /dama multi-service tactics, techniques ... - UHF-Satcom.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
25-kHz AD HOC DAMA<br />
SETUP GUIDE – AN/PSC-<br />
5C/D RADIOS<br />
1. The following are required before<br />
setup:<br />
a. AN/PSC-5C/D<br />
b. Satellite Antenna<br />
c. Proper Crypto (ANDVT)<br />
d. Proper Orderwire set<br />
e. Good batteries<br />
2. Turn radio on to PT, let the BIT<br />
finish, then ESC.<br />
3. Go to Set Presets (3), enter.<br />
4. Choose Set Mode Presets (1).<br />
5. > to DAMA; hit enter.<br />
6. Choose Preset number 1; hit enter.<br />
• Choose COMSEC fill slot: Use TEK<br />
01 as the default fill slot for ANDVT.<br />
7. Choose type of Crypto: ANDVT;<br />
enter.<br />
8. Choose Data transfer rate—<br />
• 2400; enter.<br />
9. Choose 25-kHz, enter.<br />
10. Channel number; enter.<br />
11. > Normal; enter<br />
12. TPWR select 43dbm; enter.<br />
13. Code 60; enter.<br />
14. OW: CT; enter.<br />
15. Range: Active, enter.<br />
16. Send Status B, YES<br />
17. Hit ESC X 2.<br />
18. Select Current Mode; enter.<br />
19. Change mode to LOS; enter.<br />
20. Hit ESC.<br />
21. Go to Database Options (2), enter.<br />
22. Go to Guard List (2), enter.<br />
23. > ADD, enter ##### (the network<br />
ID number from the SOI) enter.<br />
(DO NOT PUT THE TBA HERE!)<br />
24. Hit ESC twice.<br />
25. Go to Configuration (4), enter.<br />
26. Go to Terminal Data (1), enter.<br />
27. Enter ADDRESS ##### (the TBA,<br />
from the SOI) hit enter. (DO NOT<br />
PUT A NETWORK ADDRESS<br />
HERE!)<br />
28. DS-101 ADD, ignore.<br />
29. Backlight Timer, (user pref), enter.<br />
30. Msg Release: Manual. Enter.<br />
31. ENTER LAT N<br />
LON E<br />
TIME = ZULU TIME<br />
(not required)<br />
32. Platform: Stationary, hit enter.<br />
33. Freq Bands: Unlimited.<br />
34. Ext PA Opt: Normal.<br />
35. Remote Opt: PRCD.<br />
36. Press ESC twice.<br />
37. Change radio on/off switch to F1.<br />
38. Input ANDVT in fill slot 1.<br />
39. Follow the on screen instructions<br />
for filling the key. Watch for the Key<br />
Filled message on the screen. Be<br />
patient.<br />
25-kHz TDMA DAMA<br />
40. Change radio on/off switch to F2.<br />
41. Load Orderwire Keys, LANT =<br />
C5594 (positions 3-4), IO = C5596<br />
(positions 1-2) (Input the same key<br />
set in positions). Do not connect the<br />
cable until the ANCD says “connect<br />
to radio”. Cycle the radio to CT and<br />
return to F2 if it continually fails to<br />
load. Be patient.<br />
42. Return on/off switch back to CT.<br />
43. Go to Current Mode (1) and hit<br />
enter.<br />
44. Change mode back to DAMA; hit<br />
enter.<br />
45. Press Preset #1, hit the 1 key on<br />
the keypad; hit enter.<br />
46. Enter correct TK##; hit enter.<br />
47. Hit enter to confirm the remainder<br />
of the settings until SEND STATUS<br />
B YES/NO appears.<br />
48. Ensure antenna is connected at this<br />
time, with antenna on azimuth to<br />
satellite<br />
49. At SEND STATUS B, select YES,<br />
hit enter.<br />
50. Select the <strong>service</strong> preset desired<br />
(P01, P02, etc), hit enter twice.<br />
51. Radio screen will blink, an arrow in<br />
the right side of the screen will go<br />
up and then down once or twice,<br />
then see acquiring, then range,<br />
then 25-kHz AC connected-SRVidle<br />
52. NOTE: AD HOC DAMA WILL<br />
ALLOW TBA-TO-TBA, TBA TO<br />
MULTIPLE TBA, AND TBA TO<br />
NETWORK CONNECTIONS.<br />
53. Hit next to Service Setup (1),<br />
select R (Routine), then enter the<br />
TBA, MULTIPLE TBA’S, OR TO A<br />
NETWORK ADDRESS enter time<br />
required, hit enter and then Send,<br />
enter.<br />
54. Radio screen will show arrows on<br />
the right going up and down and<br />
then the screen will display 25-kHz<br />
AC SRV-RX/TX (the station or<br />
network called will change at the<br />
same time).<br />
55. Ready to talk as normal (be<br />
patient).<br />
56. To terminate setup, select<br />
Teardown (2) THE CONNECTION<br />
MUST BE TORN DOWN AFTER<br />
COMPLETING TRAFFIC TO<br />
AVOID INTERFERING WITH<br />
OTHER STATIONS’ TRAFFIC.<br />
57. Terminal will be in idle mode.<br />
NOTE: To send data: (for<br />
example, KL-43 or V-Mail) change the<br />
V2400 to D2400.<br />
NOTE: If the radio is not working<br />
properly cycle the radio off/on several<br />
times. Filter Tune does not correct all<br />
as it did with older versions of radios!<br />
38. Do not connect the cable until the<br />
ANCD says “connect to radio”.<br />
ERROR CODES = DO THIS<br />
(PREVENTIVE MEASURE)<br />
77 = Talk to net NCS. NCS needs<br />
to check with Naples to insure the<br />
TBA is on line.<br />
82 = Check the TBA entered into<br />
the radio to ensure it is correct.<br />
(pmcs)<br />
90 = This is a busy signal. Call<br />
back later.<br />
92 = Indicates conference call to<br />
more than one terminal was made. At<br />
least one terminal is not on the air but<br />
others are.<br />
Troubleshooting DAMA problems<br />
Problem: Fail to get past 25-kHz<br />
AC – Acquiring M – Idle when attempting<br />
first connection after initial setup. No up<br />
and down arrows displayed on the right<br />
side of the screen.<br />
Solution: Ensure the current<br />
Orderwire key segment is loaded in fill<br />
slots 1–4 in F2. Lack of the current<br />
orderwire COMSEC loaded and/or not in<br />
1 – 4 will cause a connection stop at the<br />
25-kHz AC – Acquiring – Idle window<br />
during initial connection.<br />
Problem: Cannot get the Orderwire<br />
COMSEC to load.<br />
Solution: Do not connect the<br />
ANCD cable to the radio until the ANCD<br />
displays Connect ANCD to Radio. Press<br />
the down arrow after connecting the<br />
cable, follow on screen instructions.<br />
Problem: COMSEC Alarm<br />
continues to popup.<br />
Solution: Refill keys in F1.<br />
Problem: CTIC alarm.<br />
Solution: Refill the orderwire key in<br />
the correct positions – F2.<br />
Problem: Data <strong>com</strong>munications not<br />
getting through but voice<br />
<strong>com</strong>munications are.<br />
Solution: Run Link Test. It is item 7<br />
in DAMA menu, needs to be run at 32<br />
kbps, and the Symbol Errors need to be<br />
less than 100 when transmitting data.<br />
Takes about a minute to run and lets the<br />
operator know a better signal is needed.<br />
Info Code 93 appears, send back<br />
information report and wait since<br />
someone else is running the test.<br />
ERROR CODES = DO THIS<br />
D-19