uhf tacsat /dama multi-service tactics, techniques ... - UHF-Satcom.com
uhf tacsat /dama multi-service tactics, techniques ... - UHF-Satcom.com uhf tacsat /dama multi-service tactics, techniques ... - UHF-Satcom.com
D-8 (5) Observe display. See Table D-4 if LOGIN is rejected by controller. CURRENT MODE DAMA -P1 - -060 TEK1 PSK ANDVT V2400 5KHz Tpwr 35 dbm Channel Number: 136 R248.900 T302.500 Code: 060 OW:CT Normal Range: Active Login: Over The Air Service Preset: 01 Start DAMA for 01000 DAMA SQ - - 045 5K Acquiring N SRV-Idle 1-Service Setup (a) Acquiring—Acquisition in process. (b) Range—Wait while ranging in process. (c) Log in—Manual log in required. (d) Log in-Pnd—Login pending. (e) Connected—Log in successful. (6) At SRVC ASGND popup message, enter on ACCEPT. To reject the service, use the arrow keys to select REJECT and press ENT key. Note: When a warning or error message is displayed, refer to tables D-5 and D-6 for proper corrective action. Srvc Asgnd CIR TEK ANDVT V2400 Prec:R EN D:01000 SYN S:02000 {ACCEPT} Note: When SRV-RX/TX appears on the display, the terminal is ready for normal communications. See Table D-7 for hot keys to access additional tasks.
Message Action A Acquisition Failed C Circuit Aborted Denied (Reason) Mismatch Detected Preempted Receive Buffer Overflow Set up Queued (Reason) Set up Rejected (Reason) Table D-4. Messages, 5-kHz DAMA Terminal is not receiving OW. Check azimuth, power out, and reposition antenna. Check previous status messages. If logged out, log in over-the-air. Other messages include circuit not available (especially DASA) and the reason. Attempt to re-establish or establish a different type of service. Circuit service request is denied for the stated reason. If condition is correctable, take appropriate action or try again later. An incoming service is established but a mismatch is detected between the service and the current mode settings. Check setting of PT/CT mode and type of attached data device. The channel controller preempted the circuit. Wait for it to resume before transmitting. Or Contact was temporarily lost with the controller; wait for it to resume. Check data device for incomplete message or errors in message. If needed, request source to retransmit message. Service is queued for the reason supplied. Local—terminal called is logged in but time-slot is unavailable. MHOP—terminal called is not logged in with controller. If it is in another footprint, wait. If it is supposed to be in the current footprint, teardown and try again later. Service request is denied for the stated reason. Try again later unless one of the following reasons is displayed. Data Rate—Requested a DASA service at higher than 2400 bps—no 25-kHz DASA channel available. Not Assignable—The LQ from terminal or the destination terminal is poor. Check LQ in network state menu. If LQ is low, check antenna or raise power. Prec. Violation—The precedence entered is not allowed. Check network state menu for assigned values. Ensure previous messages do not state logged out. If previous message stated logged out, log in over-the-air and re-attempt service set up at lower precedence. Service Restrict—Request for a 2400 bps circuit denied due to network traffic. Reduce data rate or wait until LIO no longer displayed in network state. Terminated (Reason) An existing service is terminated for the stated reason. Try again later. COMMAND Rejected Check parameters and network; try again. Rejected Port is busy (Check Current Mode) Request is rejected because of an existing active service. Ensure terminal is idle before setting up a service. D-9
- Page 63 and 64: Appendix B Information Request Code
- Page 65 and 66: Table B-1. Information Request Code
- Page 67 and 68: Table B-1. Information Request Code
- Page 69 and 70: Table B-1. Information Request Code
- Page 71 and 72: Table B-2. Configuration Codes Conf
- Page 73 and 74: C-2 Option Table C-2. MIL-STD 188-1
- Page 75 and 76: C-4 Table C-4. UHF SATCOM Programmi
- Page 77 and 78: pointing using the SATCOM receive s
- Page 79 and 80: 5. AN/PSC-117F DAMA UHF SATCOM a. U
- Page 81 and 82: C-10 Table C-7. DAMA Programming Ch
- Page 83 and 84: C-12 Table C-8. DAMA Net Preset Par
- Page 85 and 86: C-14 Figure C-6. DAMA Port Configur
- Page 87 and 88: C-16 Figure C-7. DAMA Destination P
- Page 89 and 90: h. Passive ranging and ephemeris da
- Page 91 and 92: (c) Select the destination to be ca
- Page 93 and 94: • ACTIVE—Service request has be
- Page 95 and 96: q. Terminate 25-kHz AC DAMA calls o
- Page 97 and 98: communications. Slower data rate li
- Page 99 and 100: (d) Select the desired DAMA net by
- Page 101 and 102: completion of the communications. P
- Page 103 and 104: C-32 Figure C-12. MSG Service Call
- Page 105 and 106: C-34 Figure C-14. DAMA Service Stat
- Page 107 and 108: 1. Line of Sight (LOS) Operations A
- Page 109 and 110: k. Enter channel number (009 to 239
- Page 111 and 112: GUARD LIST VIEW 1 64000 ------ ----
- Page 113: (13) For DASA only, enter time requ
- Page 117 and 118: Message Action Aborted To:xxxx (Rea
- Page 119 and 120: Table D-7. Hot Keys, 5-kHz DAMA Key
- Page 121 and 122: (9) Enter configuration code, if re
- Page 123 and 124: (1) Select over-the-air, if the ter
- Page 125 and 126: 25-kHz AD HOC DAMA SETUP GUIDE - AN
- Page 127 and 128: 5C/D RADIOS 1. The following are re
- Page 129 and 130: Table D-8. 5-kHz DAMA Operations (S
- Page 131 and 132: Table D-8. 5-kHz DAMA Operations (S
- Page 133 and 134: E-2 d. Programming operating modes.
- Page 135 and 136: (12) After pushing the variable pos
- Page 137 and 138: d. radio. Prior to COLD START, pres
- Page 139 and 140: aa. INTKG should flash. Leave as is
- Page 141 and 142: 1. Skyfire Operator Training Append
- Page 143 and 144: The following message appears- F-2
- Page 145 and 146: F-4 CI MENU LOAD PRESETS LOADING PR
- Page 147 and 148: STEP 2. Rotate selector control kno
- Page 149 and 150: (1) On = Activates guard receiver.
- Page 151 and 152: 1. Setting Up for DAMA Appendix G A
- Page 153 and 154: (1) Enter *92 then depress the Ente
- Page 155 and 156: Appendix H EMI CHARACTERIZATION CHE
- Page 157 and 158: Appendix J CUT SHEETS The following
- Page 159 and 160: DAMA Database Set up Presets Mode P
- Page 161 and 162: Appendix K Prioritization Scheme Ta
- Page 163 and 164: References Joint CJCSM 3122.01, Joi
D-8<br />
(5) Observe display. See Table D-4 if LOGIN is rejected by controller.<br />
CURRENT MODE<br />
DAMA -P1 - -060<br />
TEK1 PSK ANDVT V2400<br />
5KHz Tpwr 35 dbm<br />
Channel Number: 136<br />
R248.900 T302.500<br />
Code: 060 OW:CT<br />
Normal Range: Active<br />
Login: Over The Air<br />
Service Preset: 01<br />
Start DAMA for 01000<br />
DAMA SQ - - 045<br />
5K Acquiring N<br />
SRV-Idle<br />
1-Service Setup<br />
(a) Acquiring—Acquisition in process.<br />
(b) Range—Wait while ranging in process.<br />
(c) Log in—Manual log in required.<br />
(d) Log in-Pnd—Login pending.<br />
(e) Connected—Log in successful.<br />
(6) At SRVC ASGND popup message, enter on ACCEPT. To reject the <strong>service</strong>, use<br />
the arrow keys to select REJECT and press ENT key.<br />
Note: When a warning or error message is displayed, refer to tables D-5 and D-6 for<br />
proper corrective action.<br />
Srvc Asgnd<br />
CIR TEK ANDVT V2400<br />
Prec:R EN D:01000<br />
SYN S:02000 {ACCEPT}<br />
Note: When SRV-RX/TX appears on the display, the terminal is ready for normal<br />
<strong>com</strong>munications. See Table D-7 for hot keys to access additional tasks.