ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, and ES2024R) 8) Click Next. A screen appears with the next configurable device: the Intel(R)82559 Fast Ethernet LAN. d. Click Internet Protocol (TCP/IP) to highlight it, then click Properties. Configure the Fast Ethernet network adapter card as follows: 1) Click “Use the following IP address.” In the IP Address field enter the IP address for the Windows 2000 Advanced node from Table 2–2, then press Tab. 2) Change the subnet mask to the netmask address from Table 2–2, or skip this field (accept the default). 3) If you have a gateway (router), tab to the Default Gateway field and type the gateway address from Table 2–2. This completes the entering of IP address information. 4) Click Advanced and add any additional gateway entries that the site requires. 5) If the site chooses to implement WINS, click the WINS tab (otherwise skip this step), then do the following to enter WINS information: a) Click Add and type the address from Table 2–2. Click Add again. b) Enter any additional IP addresses from Table 2–2. 6) Click the DNS tab. 7) If the site has any DNS servers, click Add (otherwise skip this step). In the window that appears, enter the IP address for the first DNS server from Table 2–2; then click Add again. 8) If applicable, click Add and enter any additional DNS servers. 9) Click to uncheck “Register the connections added in DNS.” 10) Leave the default selections for the DNS suffix as they are. (“Append primary…and append parent….”) 11) Click OK. 12) Click OK. 13) Click Next. Skip to step 13. ES5085R server: The detected device is the Intel[R] PRO/100+ Dual Port Server Adapter #2. These default components are checked: • Client for Microsoft Networks • File and Print Sharing for Microsoft Networks • Internet Protocol (TCP/IP) You may change these selections as desired. Click components to check or uncheck them. By default, this adapter is not used by ClearPath. Continue customizing the ES5085R as follows: 3–22 Version 009B (Web Only) 7850 5104–009
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, and ES2024R) a. Click Next. A screen appears with the next configurable device: the Intel[R] PRO/100+ Dual Port Server Adapter. The same default components are checked again (see bulleted list above). b. Select File and Print Sharing and click Properties. A Server Optimization box appears. c. Select Balance, then click OK. d. Click Internet Protocol (TCP/IP) to highlight it, then click Properties. Configure the Fast Ethernet network adapter card as follows: 1) Click “Use the following IP address.” In the IP Address field enter the IP address for the Windows 2000 Advanced node from Table 2–2, then press Tab. 2) Change the subnet mask to the netmask address from Table 2–2, or skip this field (accept the default). 3) If you have a gateway (router), tab to the Default Gateway field and type the gateway address from Table 2–2. This completes the entering of IP address information. 4) Click Advanced and add any additional gateway entries that the site requires. 5) If the site chooses to implement WINS, click the WINS tab (otherwise skip this step), then do the following to enter WINS information: a) Click Add and type address from Table 2–2. Click Add again. b) Enter any additional IP addresses from Table 2–2. 6) Click the DNS tab. 7) If the site has any DNS servers, click Add (otherwise skip this step). In the window that appears, enter the IP address for the first DNS server from Table 2–2; then click Add again. 8) If applicable, click Add and enter any additional DNS servers. 9) Click to uncheck “Register this connection’s addresses in DNS.” 10) Leave the default selections for the DNS suffix as they are. (“Append primary…and append parent….”) 11) Click OK. 12) Click OK. 13) Click Next. A screen appears with the next configurable device: the SysKonnect FDDI PCI Adapter SK-5544 [SK-NET…]. 7850 5104–009 Version 009B (Web Only) 3–23
- Page 37 and 38: Notation Conventions About This Gui
- Page 39 and 40: Section 1 Introduction and Installa
- Page 41 and 42: Table 1-2. ClearPath IX Server Comp
- Page 43 and 44: 1.2.2. Installation Procedure Overv
- Page 45 and 46: Introduction and Installation Overv
- Page 47 and 48: • Configure a resilient 2200 node
- Page 49 and 50: External Communications Interface O
- Page 51 and 52: Section 2 Installation Checklists a
- Page 53 and 54: Table 2-1. General Installation Inf
- Page 55 and 56: Component Windows 2000 or Windows N
- Page 57 and 58: 2.3. Installation Tips Caution Inst
- Page 59 and 60: Finding Correct UnixWare and EBRS L
- Page 61 and 62: 2.4.1. DEPCON Workstation Requireme
- Page 63 and 64: Caution Installation Checklists and
- Page 65 and 66: Installation Checklists and Tips 3.
- Page 67 and 68: Section 3 Installing Windows 2000 A
- Page 69 and 70: Installing Windows 2000 Advanced Se
- Page 71 and 72: Installing Windows 2000 Advanced Se
- Page 73 and 74: Installing Windows 2000 Advanced Se
- Page 75 and 76: Installing Windows 2000 Advanced Se
- Page 77 and 78: Installing Windows 2000 Advanced Se
- Page 79 and 80: Installing Windows 2000 Advanced Se
- Page 81 and 82: Installing Windows 2000 Advanced Se
- Page 83 and 84: Installing Windows 2000 Advanced Se
- Page 85 and 86: Installing Windows 2000 Advanced Se
- Page 87: Installing Windows 2000 Advanced Se
- Page 91 and 92: Installing Windows 2000 Advanced Se
- Page 93 and 94: Installing Windows 2000 Advanced Se
- Page 95 and 96: Section 4 Installing Windows NT Ser
- Page 97 and 98: Installing Windows NT Server, Enter
- Page 99 and 100: Installing Windows NT Server, Enter
- Page 101 and 102: Installing Windows NT Server, Enter
- Page 103 and 104: Installing Windows NT Server, Enter
- Page 105 and 106: Installing Windows NT Server, Enter
- Page 107 and 108: Installing Windows NT Server, Enter
- Page 109 and 110: Installing Windows NT Server, Enter
- Page 111 and 112: Installing Windows NT Server, Enter
- Page 113 and 114: Installing Windows NT Server, Enter
- Page 115 and 116: Installing Windows NT Server, Enter
- Page 117 and 118: Installing Windows NT Server, Enter
- Page 119 and 120: Installing Windows NT Server, Enter
- Page 121 and 122: Installing Windows NT Server, Enter
- Page 123 and 124: Section 5 Installing Windows NT Ser
- Page 125 and 126: Installing Windows NT Server, Enter
- Page 127 and 128: Installing Windows NT Server, Enter
- Page 129 and 130: Installing Windows NT Server, Enter
- Page 131 and 132: Installing Windows NT Server, Enter
- Page 133 and 134: ID 0 1 2 3 4 5 6 Installing Windows
- Page 135 and 136: Installing Windows NT Server, Enter
- Page 137 and 138: Installing Windows NT Server, Enter
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, <strong>and</strong> ES2024R)<br />
a. Click Next.<br />
A screen appears with the next configurable device: the Intel[R] PRO/100+ Dual<br />
Port Server Adapter. The same default components are checked again (see<br />
bulleted list above).<br />
b. Select File <strong>and</strong> Print Sharing <strong>and</strong> click Properties.<br />
A Server Optimization box appears.<br />
c. Select Balance, then click OK.<br />
d. Click Internet Protocol (TCP/IP) to highlight it, then click Properties. Configure<br />
the Fast Ethernet network adapter card as follows:<br />
1) Click “Use the following IP address.” In the IP Address field enter the IP<br />
address for the Windows 2000 Advanced node from Table 2–2, then press Tab.<br />
2) Change the subnet mask to the netmask address from Table 2–2, or skip this<br />
field (accept the default).<br />
3) If you have a gateway (router), tab to the Default Gateway field <strong>and</strong> type the<br />
gateway address from Table 2–2. This completes the entering of IP address<br />
information.<br />
4) Click Advanced <strong>and</strong> add any additional gateway entries that the site requires.<br />
5) If the site chooses to implement WINS, click the WINS tab (otherwise skip this<br />
step), then do the following to enter WINS information:<br />
a) Click Add <strong>and</strong> type address from Table 2–2. Click Add again.<br />
b) Enter any additional IP addresses from Table 2–2.<br />
6) Click the DNS tab.<br />
7) If the site has any DNS servers, click Add (otherwise skip this step). In the<br />
window that appears, enter the IP address for the first DNS server from Table<br />
2–2; then click Add again.<br />
8) If applicable, click Add <strong>and</strong> enter any additional DNS servers.<br />
9) Click to uncheck “Register this connection’s addresses in DNS.”<br />
10) Leave the default selections for the DNS suffix as they are. (“Append<br />
primary…<strong>and</strong> append parent….”)<br />
11) Click OK.<br />
12) Click OK.<br />
13) Click Next.<br />
A screen appears with the next configurable device: the SysKonnect FDDI PCI<br />
Adapter SK-5544 [SK-NET…].<br />
7850 5104–009 Version 009B (Web Only) 3–23