ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, and ES2024R) 3.4. Installing and Configuring Windows 2000 Advanced Server The Windows 2000 Advanced Server installation process consists of an installation phase (3.4.1) in which prompts appear as text messages and a configuration phase (3.4.2) in which prompts are presented as graphical screens. The following subsections describe the Notes: • Switch the monitor concentrator to the Intel node position before beginning (see 2.5.2). • Configuration settings are chosen to minimize problems during initial installation. After hardware RFU, the site may wish to customize the configuration to meet its needs. 3.4.1. Installing the Windows 2000 Advanced Server Operating System Begin Windows 2000 Advanced Server installation as follows: 1. Insert the Windows 2000 Advanced Bootable CD-ROM into the drive unit. Note: To avoid missing a five-second timing window, please read all of step 2 (next) before executing it. 2. On the Intel node, reboot or turn power on. After the hardware initialization messages are displayed, the following messages appears at the top of the screen: Setup is inspecting your computer's hardware configuration... Windows 2000 Setup ================== If you have the RAD6002-P64 RAID Controller, press the F6 key within five seconds. This will let you install the driver before the OS installation, a requirement at this time. 3. For all systems, wait for the Windows 2000 installation program to load its standard device files. The following message is then displayed: Setup could not determine the type of one or more mass storage devices... 4. Insert the “Unisys-Mylex RAID Win2000 Drivers” diskette (4556 3780) and press S, then Enter. 5. Select the Mylex AcceleRAID 352 Disk Array Controller to install it. 6. After the driver is installed, remove the diskette and press Enter to continue. 7. The Setup welcome menu appears: Welcome to Setup This portion of the Setup program prepares Microsoft Windows 2000 to run on your computer. 3–16 Version 009B (Web Only) 7850 5104–009
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, and ES2024R) ù To set up Windows 2000 now, press Enter. ù To repair a Windows 2000 installation, press R. ù To quit Setup without installing Windows 2000, press F3. 8. Press Enter to begin setting up Windows 2000. If an operating system was previously installed on this server, the following message may appear: Setup has determined that your computer's startup hard disk is new or has been erased, or that your computer is running an operating system that is incompatible with Windows 2000. If the hard disk is new or has been erased, or if you want to discard its current contents, you can choose to continue Setup. If your computer is running an operating system that is incompatible with Windows 2000, continuing Setup may damage or destroy the existing operating system. ù To continue Setup, press C. CAUTION: Any data currently on your computer's startup hard disk will be lost. ù To quit Setup, press F3. If the message above appears, press C to continue. A Windows 2000 Licensing Agreement screen appears. 9. Press F8 to indicate that you agree with the terms of the license agreement. A screen appears that identifies the unpartitioned disk space. Windows 2000 Server Setup ====================== The following shows existing partitions and unpartitioned space on this computer. Use the UP and DOWN ARROW keys to move the highlight to an item in the list. To set up Windows 2000 on the selected items, press ENTER. To create a partition in the unpartitioned space, press C. To delete the selected partition, press D. Unpartitioned space xxxx MB ENTER=Install C=Create Partition F3=Exit 7850 5104–009 Version 009B (Web Only) 3–17
- Page 31 and 32: About This Guide ClearPath HMP IX S
- Page 33 and 34: About This Guide This guide gives c
- Page 35 and 36: About This Guide OS 2200 Exec Syste
- Page 37 and 38: Notation Conventions About This Gui
- Page 39 and 40: Section 1 Introduction and Installa
- Page 41 and 42: Table 1-2. ClearPath IX Server Comp
- Page 43 and 44: 1.2.2. Installation Procedure Overv
- Page 45 and 46: Introduction and Installation Overv
- Page 47 and 48: • Configure a resilient 2200 node
- Page 49 and 50: External Communications Interface O
- Page 51 and 52: Section 2 Installation Checklists a
- Page 53 and 54: Table 2-1. General Installation Inf
- Page 55 and 56: Component Windows 2000 or Windows N
- Page 57 and 58: 2.3. Installation Tips Caution Inst
- Page 59 and 60: Finding Correct UnixWare and EBRS L
- Page 61 and 62: 2.4.1. DEPCON Workstation Requireme
- Page 63 and 64: Caution Installation Checklists and
- Page 65 and 66: Installation Checklists and Tips 3.
- Page 67 and 68: Section 3 Installing Windows 2000 A
- Page 69 and 70: Installing Windows 2000 Advanced Se
- Page 71 and 72: Installing Windows 2000 Advanced Se
- Page 73 and 74: Installing Windows 2000 Advanced Se
- Page 75 and 76: Installing Windows 2000 Advanced Se
- Page 77 and 78: Installing Windows 2000 Advanced Se
- Page 79 and 80: Installing Windows 2000 Advanced Se
- Page 81: Installing Windows 2000 Advanced Se
- Page 85 and 86: Installing Windows 2000 Advanced Se
- Page 87 and 88: Installing Windows 2000 Advanced Se
- Page 89 and 90: Installing Windows 2000 Advanced Se
- Page 91 and 92: Installing Windows 2000 Advanced Se
- Page 93 and 94: Installing Windows 2000 Advanced Se
- Page 95 and 96: Section 4 Installing Windows NT Ser
- Page 97 and 98: Installing Windows NT Server, Enter
- Page 99 and 100: Installing Windows NT Server, Enter
- Page 101 and 102: Installing Windows NT Server, Enter
- Page 103 and 104: Installing Windows NT Server, Enter
- Page 105 and 106: Installing Windows NT Server, Enter
- Page 107 and 108: Installing Windows NT Server, Enter
- Page 109 and 110: Installing Windows NT Server, Enter
- Page 111 and 112: Installing Windows NT Server, Enter
- Page 113 and 114: Installing Windows NT Server, Enter
- Page 115 and 116: Installing Windows NT Server, Enter
- Page 117 and 118: Installing Windows NT Server, Enter
- Page 119 and 120: Installing Windows NT Server, Enter
- Page 121 and 122: Installing Windows NT Server, Enter
- Page 123 and 124: Section 5 Installing Windows NT Ser
- Page 125 and 126: Installing Windows NT Server, Enter
- Page 127 and 128: Installing Windows NT Server, Enter
- Page 129 and 130: Installing Windows NT Server, Enter
- Page 131 and 132: Installing Windows NT Server, Enter
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, <strong>and</strong> ES2024R)<br />
3.4. Installing <strong>and</strong> Configuring Windows 2000<br />
Advanced Server<br />
The Windows 2000 Advanced Server installation process consists of an installation phase<br />
(3.4.1) in which prompts appear as text messages <strong>and</strong> a configuration phase (3.4.2) in<br />
which prompts are presented as graphical screens. The following subsections describe the<br />
Notes:<br />
• Switch the monitor concentrator to the Intel node position before beginning (see<br />
2.5.2).<br />
• <strong>Configuration</strong> settings are chosen to minimize problems during initial installation.<br />
After hardware RFU, the site may wish to customize the configuration to meet its<br />
needs.<br />
3.4.1. Installing the Windows 2000 Advanced Server Operating<br />
System<br />
Begin Windows 2000 Advanced Server installation as follows:<br />
1. Insert the Windows 2000 Advanced Bootable CD-ROM into the drive unit.<br />
Note: To avoid missing a five-second timing window, please read all of step 2<br />
(next) before executing it.<br />
2. On the Intel node, reboot or turn power on.<br />
After the hardware initialization messages are displayed, the following messages<br />
appears at the top of the screen:<br />
Setup is inspecting your computer's hardware configuration...<br />
Windows 2000 Setup<br />
==================<br />
If you have the RAD6002-P64 RAID Controller, press the F6 key within five seconds.<br />
This will let you install the driver before the OS installation, a requirement at this time.<br />
3. For all systems, wait for the Windows 2000 installation program to load its st<strong>and</strong>ard<br />
device files. The following message is then displayed:<br />
Setup could not determine the type of one or more mass storage devices...<br />
4. Insert the “Unisys-Mylex RAID Win2000 Drivers” diskette (4556 3780) <strong>and</strong> press S, then<br />
Enter.<br />
5. Select the Mylex AcceleRAID 352 Disk Array Controller to install it.<br />
6. After the driver is installed, remove the diskette <strong>and</strong> press Enter to continue.<br />
7. The Setup welcome menu appears:<br />
Welcome to Setup<br />
This portion of the Setup program prepares<br />
Microsoft Windows 2000 to run on your computer.<br />
3–16 Version 009B (Web Only) 7850 5104–009