ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, and ES2024R) n. If you have a gateway (router), tab to the Default Gateway field and type the gateway address from Table 2–2. o. Click Advanced and add any additional gateway entries that the site requires. p. If the site chooses to implement WINS, click the WINS tab (otherwise skip this step), then enter WINS information as follows: 1) Click Add and type the address from Table 2–2. Click Add again. 2) Enter any additional IP addresses from Table 2–2. q. Click the DNS tab. r. If the site has any DNS servers, click Add (otherwise skip this step). In the window that appears, enter the IP address for the first DNS server from Table 2–2; then click Add again. s. If applicable, click Add and enter any additional DNS servers. t. Click to uncheck “Register the connections added in DNS.” u. Leave the default selections for the DNS suffix as they are. (“Append primary…and append parent….”) v. Click OK. w. Click OK. x. Click Next. 10. A Workgroup or Computer Domain screen identifies the host name of the Windows 2000 node and asks whether the node is to participate in a workgroup or domain. Proceed as follows: a. Click No. b. Enter the workgroup name CLEARPATH in the box labeled Workgroup or computer domain. Note: You can enter a different workgroup name if the client site requirements are different. c. Click Next. The Windows 2000 Server Setup screen indicates that it is installing Windows 2000 components. This may take several minutes. A progress bar shows the status of the installation. The following message appears: You have successfully completed Windows 2000 Setup. If there is a CD in your drive, remove it. Then, to restart your computer, click Finish. 11. Click Finish. The server reboots. After a few minutes, the Windows 2000 Advanced Server logo appears and you are prompted to press Ctrl-Alt-Del to log on. 12. Log on as the administrator (3.5). A menu labeled Windows 2000 Configure Your Server appears, giving three options: 3–12 Version 009B (Web Only) 7850 5104–009
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, and ES2024R) ù This is the only server in my network. ù One or more servers are already running in my network. ù I will configure this server later. 13. Click “I will configure this server later.” Then click Next. 14. Tab to the check box labeled “Show this screen at startup” and clear it. 15. Close the Configure Your Server window. At this point, you should still be logged on as the administrator. Complete Windows 2000 Advanced installation as described in 7.2. 3.3. Configuring the RAID Controller Configure the RAID disk controller for RAID level 1 (mirroring) for two disks units. Sites can reconfigure a different RAID level following hardware RFU, if desired. For detailed information see the Mylex RAID Management documentation available on the CD- ROM labeled "Mylex Solutions Software Kit x.xx." Notes: • Switch the monitor concentrator to the Intel node position before beginning (see 2.5.2). • If you are performing a full installation on a system that was preloaded, do not format the RAID disk. Instead, use the DAC BIOS utility to initialize the RAID volume before you reload the operating system. Formatting the disk makes the drive unrecognizable to the software. • In step 2, you must press Alt-M within a few seconds to enter the BIO Options Utility. • In step 8, you must press Alt-R within a few seconds to enter the RAID controller configuration procedure; otherwise, the normal boot procedure continues. See next note for ES2024R server. • For the ES2024R server, before you press Alt-R, you must press Alt-M to access the BIOS options utility. Then press Alt-R in order to access the Mylex RAID EzAssist utility, as instructed in step 8. Take the following steps to run the RAID controller configuration utility: 1. Power on or reboot the Intel node. Several start-up messages appear, ending in a prompt to press Alt-M, as follows: DAC1100 ADAPTER BIOS VERSION x.xx Mylex Corporation Host Adapter-1 Firmware Version x.xx DRAM size xxx MB . . . Spinning up drives... . 7850 5104–009 Version 009B (Web Only) 3–13
- Page 27 and 28: How to Use This Guide About This Gu
- Page 29 and 30: About This Guide Section 15. Instal
- Page 31 and 32: About This Guide ClearPath HMP IX S
- Page 33 and 34: About This Guide This guide gives c
- Page 35 and 36: About This Guide OS 2200 Exec Syste
- Page 37 and 38: Notation Conventions About This Gui
- Page 39 and 40: Section 1 Introduction and Installa
- Page 41 and 42: Table 1-2. ClearPath IX Server Comp
- Page 43 and 44: 1.2.2. Installation Procedure Overv
- Page 45 and 46: Introduction and Installation Overv
- Page 47 and 48: • Configure a resilient 2200 node
- Page 49 and 50: External Communications Interface O
- Page 51 and 52: Section 2 Installation Checklists a
- Page 53 and 54: Table 2-1. General Installation Inf
- Page 55 and 56: Component Windows 2000 or Windows N
- Page 57 and 58: 2.3. Installation Tips Caution Inst
- Page 59 and 60: Finding Correct UnixWare and EBRS L
- Page 61 and 62: 2.4.1. DEPCON Workstation Requireme
- Page 63 and 64: Caution Installation Checklists and
- Page 65 and 66: Installation Checklists and Tips 3.
- Page 67 and 68: Section 3 Installing Windows 2000 A
- Page 69 and 70: Installing Windows 2000 Advanced Se
- Page 71 and 72: Installing Windows 2000 Advanced Se
- Page 73 and 74: Installing Windows 2000 Advanced Se
- Page 75 and 76: Installing Windows 2000 Advanced Se
- Page 77: Installing Windows 2000 Advanced Se
- Page 81 and 82: Installing Windows 2000 Advanced Se
- Page 83 and 84: Installing Windows 2000 Advanced Se
- Page 85 and 86: Installing Windows 2000 Advanced Se
- Page 87 and 88: Installing Windows 2000 Advanced Se
- Page 89 and 90: Installing Windows 2000 Advanced Se
- Page 91 and 92: Installing Windows 2000 Advanced Se
- Page 93 and 94: Installing Windows 2000 Advanced Se
- Page 95 and 96: Section 4 Installing Windows NT Ser
- Page 97 and 98: Installing Windows NT Server, Enter
- Page 99 and 100: Installing Windows NT Server, Enter
- Page 101 and 102: Installing Windows NT Server, Enter
- Page 103 and 104: Installing Windows NT Server, Enter
- Page 105 and 106: Installing Windows NT Server, Enter
- Page 107 and 108: Installing Windows NT Server, Enter
- Page 109 and 110: Installing Windows NT Server, Enter
- Page 111 and 112: Installing Windows NT Server, Enter
- Page 113 and 114: Installing Windows NT Server, Enter
- Page 115 and 116: Installing Windows NT Server, Enter
- Page 117 and 118: Installing Windows NT Server, Enter
- Page 119 and 120: Installing Windows NT Server, Enter
- Page 121 and 122: Installing Windows NT Server, Enter
- Page 123 and 124: Section 5 Installing Windows NT Ser
- Page 125 and 126: Installing Windows NT Server, Enter
- Page 127 and 128: Installing Windows NT Server, Enter
Installing Windows 2000 Advanced Server (ES5044R, ES5085R, <strong>and</strong> ES2024R)<br />
n. If you have a gateway (router), tab to the Default Gateway field <strong>and</strong> type the<br />
gateway address from Table 2–2.<br />
o. Click Advanced <strong>and</strong> add any additional gateway entries that the site requires.<br />
p. If the site chooses to implement WINS, click the WINS tab (otherwise skip this<br />
step), then enter WINS information as follows:<br />
1) Click Add <strong>and</strong> type the address from Table 2–2. Click Add again.<br />
2) Enter any additional IP addresses from Table 2–2.<br />
q. Click the DNS tab.<br />
r. If the site has any DNS servers, click Add (otherwise skip this step). In the<br />
window that appears, enter the IP address for the first DNS server from Table 2–2;<br />
then click Add again.<br />
s. If applicable, click Add <strong>and</strong> enter any additional DNS servers.<br />
t. Click to uncheck “Register the connections added in DNS.”<br />
u. Leave the default selections for the DNS suffix as they are. (“Append<br />
primary…<strong>and</strong> append parent….”)<br />
v. Click OK.<br />
w. Click OK.<br />
x. Click Next.<br />
10. A Workgroup or Computer Domain screen identifies the host name of the Windows<br />
2000 node <strong>and</strong> asks whether the node is to participate in a workgroup or domain.<br />
Proceed as follows:<br />
a. Click No.<br />
b. Enter the workgroup name CLEARPATH in the box labeled Workgroup or<br />
computer domain.<br />
Note: You can enter a different workgroup name if the client site<br />
requirements are different.<br />
c. Click Next.<br />
The Windows 2000 Server Setup screen indicates that it is installing Windows 2000<br />
components. This may take several minutes. A progress bar shows the status of the<br />
installation.<br />
The following message appears:<br />
You have successfully completed Windows 2000 Setup.<br />
If there is a CD in your drive, remove it. Then,<br />
to restart your computer, click Finish.<br />
11. Click Finish.<br />
The server reboots. After a few minutes, the Windows 2000 Advanced Server logo<br />
appears <strong>and</strong> you are prompted to press Ctrl-Alt-Del to log on.<br />
12. Log on as the administrator (3.5).<br />
A menu labeled Windows 2000 Configure Your Server appears, giving three options:<br />
3–12 Version 009B (Web Only) 7850 5104–009