ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Introduction and Installation Overview Install the central electronics complex Install the FDDI connections for the internal LAN and connect site administraton LANs Install SCF workstation software (if not preinstalled) Power on 2200 Node and run diagnostic tests Install and configure Windows NT or UnixWare software on each Intel node (if not preinstalled) Does site already have SPO Console ? Yes No Modify current configurations to include ClearPath HMP IX nodes and automation 2200 Node Hardware Verification 1 Figure 1–2. Installation Process Overview 6. Perform a 2200 node system check as follows: a. Power on the 2200 nodes. b. Run microdiagnostics. c. Boot and run SUMMIT. 1–6 Version 009B (Web Only) 7850 5104–009 1 Install and configure SPO server software (if not preinstalled) Copy SPO server hosts file to system consoles Install and configure SPO workstation software If using SPO Console, install temporary license key and submit registration form for permanent key. (Skip if using SPO Basic Edition.) Install SPO agents on Intel nodes Install and configure OS2200IOEsoftwareon 2200 node Run interconnect tests to verify 2200 node to Intel nodes communications Use Integration Expert to customize the configuration
Introduction and Installation Overview 7. Run SUMMIT to verify intercabinet connections. Note that the minimum level of CEC500 (model IX4400 is 1R8 and the minimum level of CC3000 (model IX5000 server or IX4800 server) is 1R1. 8. Run the applicable FDDI LAN Test under UPTS-OS2200 interface sender to Sxxxxxxx receiver as follows: • IX4400 server—Run SRLANF • IX5000 server or IX4800 server—Run CALANF Intel Node Software Installation 9. Install and configure the Windows NT or UnixWare operating system as follows: Windows 2000 Advanced Server Installation Install and configure Windows 2000 as described in Section 3 (Installing Windows 2000 Advanced Server, ES5085R and ES2024R). Note: When installing multiple Intel nodes or multiple OS 2200 nodes, see 1.3. Windows NT Server Installation Install and configure Windows NT as described in Section 4 (Windows NT Server, Enterprise Edition, for ES5085R), Section 5 (Windows NT Server, Enterprise Edition, for ES2045R), or Section 6 (Windows NT Server 4.0, for DR/2). Note: When installing multiple Intel nodes or multiple OS 2200 nodes, see 1.3. UnixWare Installation Install and configure UnixWare 7 as described in Section 8. (UnixWare 7). 10. Install and configure the ClearPath IX Customer Information Web Site as described in Section 9. Note: This step can be done at any convenient time after step 9. SPO Server Software Installation 11. Sites using SPO Basic Edition install and configure Basic Edition and related software (Section 10). Sites using SPO Console must take the steps described in 2.4.3. SPO Workstation Software Installation 12. Install and configure Windows NT Workstation, or configure Windows 2000 Professional Workstation (which comes preloaded), at the SPO workstation as described in Section 11. Configuration of Intel Nodes for Monitoring by SPO 13. Configure the Intel nodes for monitoring by SPO Basic Edition as described in Section 12. 7850 5104–009 Version 009B (Web Only) 1–7
- Page 1 and 2: Unisys e-@ction ClearPath Enterpris
- Page 3 and 4: Unisys e-@ction ClearPath Enterpris
- Page 5 and 6: Unisys e-@ction ClearPath Enterpris
- Page 7 and 8: Contents About This Guide .........
- Page 9 and 10: Contents 4.4. Installing and Config
- Page 11 and 12: Contents 8.4. Installing the UnixWa
- Page 13 and 14: Contents 11.6. Configuring the FTP
- Page 15 and 16: Contents 14.4. Installing DSPER ...
- Page 17 and 18: Appendix D. Configuring the FDDI In
- Page 19 and 20: Figures 1-1. ClearPath IX Server Co
- Page 21 and 22: Tables 1-1. Operating System Levels
- Page 23 and 24: Examples 14-1. A Minimum CMS 1100 C
- Page 25 and 26: About This Guide Purpose Scope This
- Page 27 and 28: How to Use This Guide About This Gu
- Page 29 and 30: About This Guide Section 15. Instal
- Page 31 and 32: About This Guide ClearPath HMP IX S
- Page 33 and 34: About This Guide This guide gives c
- Page 35 and 36: About This Guide OS 2200 Exec Syste
- Page 37 and 38: Notation Conventions About This Gui
- Page 39 and 40: Section 1 Introduction and Installa
- Page 41 and 42: Table 1-2. ClearPath IX Server Comp
- Page 43: 1.2.2. Installation Procedure Overv
- Page 47 and 48: • Configure a resilient 2200 node
- Page 49 and 50: External Communications Interface O
- Page 51 and 52: Section 2 Installation Checklists a
- Page 53 and 54: Table 2-1. General Installation Inf
- Page 55 and 56: Component Windows 2000 or Windows N
- Page 57 and 58: 2.3. Installation Tips Caution Inst
- Page 59 and 60: Finding Correct UnixWare and EBRS L
- Page 61 and 62: 2.4.1. DEPCON Workstation Requireme
- Page 63 and 64: Caution Installation Checklists and
- Page 65 and 66: Installation Checklists and Tips 3.
- Page 67 and 68: Section 3 Installing Windows 2000 A
- Page 69 and 70: Installing Windows 2000 Advanced Se
- Page 71 and 72: Installing Windows 2000 Advanced Se
- Page 73 and 74: Installing Windows 2000 Advanced Se
- Page 75 and 76: Installing Windows 2000 Advanced Se
- Page 77 and 78: Installing Windows 2000 Advanced Se
- Page 79 and 80: Installing Windows 2000 Advanced Se
- Page 81 and 82: Installing Windows 2000 Advanced Se
- Page 83 and 84: Installing Windows 2000 Advanced Se
- Page 85 and 86: Installing Windows 2000 Advanced Se
- Page 87 and 88: Installing Windows 2000 Advanced Se
- Page 89 and 90: Installing Windows 2000 Advanced Se
- Page 91 and 92: Installing Windows 2000 Advanced Se
- Page 93 and 94: Installing Windows 2000 Advanced Se
Introduction <strong>and</strong> <strong>Installation</strong> Overview<br />
7. Run SUMMIT to verify intercabinet connections. Note that the minimum level of<br />
CEC500 (model <strong>IX</strong>4400 is 1R8 <strong>and</strong> the minimum level of CC3000 (model <strong>IX</strong>5000 server<br />
or <strong>IX</strong>4800 server) is 1R1.<br />
8. Run the applicable FDDI LAN Test under UPTS-OS2200 interface sender to Sxxxxxxx<br />
receiver as follows:<br />
• <strong>IX</strong>4400 server—Run SRLANF<br />
• <strong>IX</strong>5000 server or <strong>IX</strong>4800 server—Run CALANF<br />
Intel Node Software <strong>Installation</strong><br />
9. Install <strong>and</strong> configure the Windows NT or UnixWare operating system as follows:<br />
Windows 2000 Advanced Server <strong>Installation</strong><br />
Install <strong>and</strong> configure Windows 2000 as described in Section 3 (Installing Windows<br />
2000 Advanced Server, ES5085R <strong>and</strong> ES2024R).<br />
Note: When installing multiple Intel nodes or multiple OS 2200 nodes, see 1.3.<br />
Windows NT Server <strong>Installation</strong><br />
Install <strong>and</strong> configure Windows NT as described in Section 4 (Windows NT Server,<br />
Enterprise Edition, for ES5085R), Section 5 (Windows NT Server, Enterprise<br />
Edition, for ES2045R), or Section 6 (Windows NT Server 4.0, for DR/2).<br />
Note: When installing multiple Intel nodes or multiple OS 2200 nodes, see 1.3.<br />
UnixWare <strong>Installation</strong><br />
Install <strong>and</strong> configure UnixWare 7 as described in Section 8. (UnixWare 7).<br />
10. Install <strong>and</strong> configure the <strong>ClearPath</strong> <strong>IX</strong> Customer Information Web Site as described in<br />
Section 9.<br />
Note: This step can be done at any convenient time after step 9.<br />
SPO Server Software <strong>Installation</strong><br />
11. Sites using SPO Basic Edition install <strong>and</strong> configure Basic Edition <strong>and</strong> related software<br />
(Section 10). Sites using SPO Console must take the steps described in 2.4.3.<br />
SPO Workstation Software <strong>Installation</strong><br />
12. Install <strong>and</strong> configure Windows NT Workstation, or configure Windows 2000<br />
Professional Workstation (which comes preloaded), at the SPO workstation as<br />
described in Section 11.<br />
<strong>Configuration</strong> of Intel Nodes for Monitoring by SPO<br />
13. Configure the Intel nodes for monitoring by SPO Basic Edition as described in<br />
Section 12.<br />
7850 5104–009 Version 009B (Web Only) 1–7