ClearPath IX Systems Installation and Configuration Guide
ClearPath IX Systems Installation and Configuration Guide ClearPath IX Systems Installation and Configuration Guide
Installing the Remaining IOE Software To allow users to install PMLite, do the following: 1. Place both the SETUP.EXE and README.TXT files from the Integration Expert CD- ROM in a shared directory on your network. 2. Instruct users to map a drive to the shared directory. 3. Instruct users that they can install PMLite by executing file SETUP.EXE from their workstations. 15–8 Version 009B (Web Only) 7850 5104–009
Section 16 Customizing the Site Customer personnel at the site perform these additional tasks: • Use Integration Expert (formerly known as PathMate) to configure other software (for example, CMS 1100) (16.2) • Use Integration Expert to create and populate the IX Network Identity Repository (16.3) • Install optional IOE products (16.4) • Customize SPO Basic Edition configurations with site-specific names (16.5) • Test TCP/IP communications (16.6) In addition, you can optionally do any of the following: • Install optional UnixWare software products (if applicable) (16.7). • Repartition the UnixWare node (16.8). • Configure a resilient 2200 node partition (16.9). You can also perform any other system configuration or tuning tasks not described in this guide. For example, you can tune or regenerate the Exec using procedures in the Exec Installation and Configuration Guide. 16.1. About Using Integration Expert The first task following hardware RFU is normally the configuration of other software. Integration Expert is the application that helps you do this. Before you can use Integration Expert, however, you must first install, on a 2200 node, a CMS 1100 configuration that includes at least one TCP/IP path to the node for communication with Integration Expert (14.5.2). After establishing an appropriate CMS 1100 configuration, you can use Integration Expert to • Further customize CMS 1100 (16.2) • Create and populate the IX Network Identity Repository (16.3) (applicable only if integrating SPO Basic Edition with CA Unicenter TNG). • Configure other products such as − TransIT Open/OLTP (OLTP-TM2200) − Open Programming Environment (OPE) 7850 5104–009 Version 009B (Web Only) 16–1
- Page 303 and 304: Installing and Configuring SPO Work
- Page 305 and 306: Installing and Configuring SPO Work
- Page 307 and 308: Section 12 Configuring Intel Nodes
- Page 309 and 310: Configuring Intel Nodes for Monitor
- Page 311 and 312: Configuring Intel Nodes for Monitor
- Page 313 and 314: Configuring Intel Nodes for Monitor
- Page 315 and 316: Configuring Intel Nodes for Monitor
- Page 317 and 318: Configuring Intel Nodes for Monitor
- Page 319 and 320: Configuring Intel Nodes for Monitor
- Page 321 and 322: Section 13 Installing the Basic OS
- Page 323 and 324: Installing the Basic OS 2200 IOE Yo
- Page 325 and 326: Installing the Basic OS 2200 IOE 5.
- Page 327 and 328: Installing the Basic OS 2200 IOE 2.
- Page 329 and 330: Installing the Basic OS 2200 IOE Yo
- Page 331 and 332: Section 14 Verifying the Interconne
- Page 333 and 334: 14.2.1. Installing HLC-2 Microcode
- Page 335 and 336: Verifying the Interconnects and Ach
- Page 337 and 338: Verifying the Interconnects and Ach
- Page 339 and 340: Verifying the Interconnects and Ach
- Page 341 and 342: Verifying the Interconnects and Ach
- Page 343 and 344: Verifying the Interconnects and Ach
- Page 345 and 346: Verifying the Interconnects and Ach
- Page 347 and 348: Section 15 Installing the Remaining
- Page 349 and 350: 15.2.2. Setting Up the TIP Environm
- Page 351 and 352: APP 3 ROLLBACK INITIALIZATION START
- Page 353: INAP3 MAX PAGES Installing the Rema
- Page 357 and 358: Customizing the Site 1. Copy the ne
- Page 359 and 360: Customizing the Site 5. Verify your
- Page 361 and 362: Customizing the Site A dialogue box
- Page 363 and 364: Customizing the Site lan-address la
- Page 365 and 366: 14. Select the Changes menu bar ite
- Page 367 and 368: Customizing the Site b. Select CP_U
- Page 369 and 370: Customizing the Site l. Repeat thes
- Page 371 and 372: 16.6. Testing TCP/IP Communications
- Page 373 and 374: Customizing the Site ClearPath IX50
- Page 375 and 376: Section 17 Installing Optional OS 2
- Page 377 and 378: Appendix A Tables of Documentation,
- Page 379 and 380: Major Hardware or Software Changes
- Page 381 and 382: Major Hardware or Software Changes
- Page 383 and 384: Intel Platform Tables of Documentat
- Page 385 and 386: Tables of Documentation, Support, a
- Page 387 and 388: Appendix B Communication Settings S
- Page 389 and 390: Communication Settings Specific to
- Page 391 and 392: Appendix C SPO/HMP IX Interface Lic
- Page 393 and 394: SPO/HMP IX Interface License Key Re
- Page 395 and 396: Appendix D Configuring the FDDI Int
- Page 397 and 398: INVENTORY_INCLUDE: Limited Comprehe
- Page 399 and 400: The HLC-2 Subsystem Connections FDD
- Page 401 and 402: Appendix E Installing OPE and SysAd
- Page 403 and 404: Glossary A ACID properties The esse
Installing the Remaining IOE Software<br />
To allow users to install PMLite, do the following:<br />
1. Place both the SETUP.EXE <strong>and</strong> README.TXT files from the Integration Expert CD-<br />
ROM in a shared directory on your network.<br />
2. Instruct users to map a drive to the shared directory.<br />
3. Instruct users that they can install PMLite by executing file SETUP.EXE from their<br />
workstations.<br />
15–8 Version 009B (Web Only) 7850 5104–009